Full "show run" output on Cisco Prime Infrastructure

Hi,
does anyone know if there's a way to see the entire "show run" config in one file?
on the gui it is presenting the configuration is divided into sections like - interfaces, ACL's, SNMP and so on...
i'm looking for one full file that i will be able to copy and paste on another device without deleting every headline.
hopefully you understand my request.
thanks,
Adir

Add - it's under the configuration archive tab:

Similar Messages

Cisco Prime Infrastructure 1.3, Mail Configuration

Hi,
I have a Cisco Prime Infrastructure 1.3 and I want to set up the mail. When I test it, I get this error:
Failed to send mail to primary SMTP server. Failed to send mail to secondary SMTP server. Please make sure that you save mail configuration by hitting 'Save' button.
I have the ip address, and the username and password. Do I need to create a new buzon for the prime? because by default the "From" field appears with
[email protected]
Thanks!!

Some extra info that has just come to my attention. At one point we were running (we're actually still running) CiscoWorks with LMS3.2 and Cisco NCS 1.x. I merged these two things together into Cisco Prime Infrastructure (upgraded the licensing to get 450 lifecycle licenses to cover the APs + all of the devices coming from LMS3.2). I followed all of the documented procedures to upgrade the NCS appliance to Prime Infrastructure. But when I type "show application" from the CLI of the NCS appliance (now the Prime Infrastructure appliance) I see this:
HQ-NCS1/admin# show application
NCS Cisco Prime Network Control System
Is that normal? Maybe this is my problem. Should this output list "Cisco Prime Infrastructure" instead of (or in addtion to) Cisco Prime Network Control System? When I login to the GUI it shows "Cisco Prime Infrastructure" and the GUI has changed considerably (menus are different) so I'm assuming that the application upgrades I launched from the CLI to go to Prime Infrastructure worked fine.

Cisco Prime Infrastructure Scheduled Configuration Archive not executing

We have a deployment of Cisco Prime Infrastrcuture 1.3 (1.3.0.20).
Configuration Archive is a feature that collects and archives the device configurations i.e. cisco switches.
You have an option to schedule this to run, say daily, weekly etc. Once scheduled you can see it in the "Jobs Dashboard" and with the "next start time" of what you configured. I have a situation whereby the time it is suppose to start - it doesnt - howevere flags the job as a "success". Not newe device configurations are archived and the "next start time" remain the same. Its almost like it is failing to execute, but some other process under the hood thinks that it was been executed correctly?
Any ideas or experience that could help here would be appreciated!

Some extra info that has just come to my attention. At one point we were running (we're actually still running) CiscoWorks with LMS3.2 and Cisco NCS 1.x. I merged these two things together into Cisco Prime Infrastructure (upgraded the licensing to get 450 lifecycle licenses to cover the APs + all of the devices coming from LMS3.2). I followed all of the documented procedures to upgrade the NCS appliance to Prime Infrastructure. But when I type "show application" from the CLI of the NCS appliance (now the Prime Infrastructure appliance) I see this:
HQ-NCS1/admin# show application
NCS Cisco Prime Network Control System
Is that normal? Maybe this is my problem. Should this output list "Cisco Prime Infrastructure" instead of (or in addtion to) Cisco Prime Network Control System? When I login to the GUI it shows "Cisco Prime Infrastructure" and the GUI has changed considerably (menus are different) so I'm assuming that the application upgrades I launched from the CLI to go to Prime Infrastructure worked fine.

Cisco Prime Infrastructure 2.0 not showing alerts from switch

Hello,
I have a prime infrastructure 2.0 running at a customer place and the customer now complains that he is not receiving link up/down messages from the switch. When i checked I have seen that if I shut down a port in the switch the prime identifies after a long time, but its not generating an alarm still. How can I fine tune the prime to fix this issue. Please help on this.
Thanks in advance

Hi,
Same problem here.
I am using Cisco Prime Infrastructure 2.0 (evaluation version for 60 days). I want to deploy port monitoring for my trunk ports between switches and some other important ports e.g. servers. Basically I want to get alarms when these ports are down, there are errors on ports and etc.
So in Design>Port Grouping I created User Defined group with important ports. In Deploy>Monitoring Deployment I selected Interface Health (default)>Deploy selected Port Groups and when selected port group I created.
Now the rule shows Deployed: Yes and Status: Active. After that I just pulled out one port which was in monitored group, waited 5min as it is set in Interface Health (default) template, and nothing happened, and worse, alarms started to show up of other ports where regular users are connected (computers was turned off), which I do not want to see at all. I tried redeploy template, I even created my own template but still no desired result.
Any suggestions how to make port monitoring work?

A job in Cisco Prime Infrastructure 2.1 has been running for 50 days

I found a job (SAM_Poller_22_15_GETVPNPoller_1878262177) in cisco prime infrastructure 2.1 (Administration -> Job Dashboard -> System-defined), which has been running for about 50 days. Is this normal? How can I stop it? Thanks for any help..
SAM_Poller_22_15_GETVPNPoller_1878262177
PollerJob
In-Progress
Running
2014-09-19 01:28
49 Days 01 : 28 : 37

Not normal, seems to be stuck. Try to stop (ncs stop) and start (ncs start) the system processes, which should stop this job.
If it happens again, i would recommend to open a TAC case for further investigation.
-Thanks
Vinod

Is cisco prime infrastructure support / can be run as syslog server?

Dear All,
is cisco prime infrastructure support / can be run as syslog server?
and,
where i can see network topology diagram, using cisco prime infrastructure?
many thanks,
Jerri

Hello. Cisco Prime LMS will be replaced by Cisco Prime Infrastructure in the near future.
In the current release of Cisco Prime Infrastructure you can't use topology diagrams. This feature is in roadmap.
About syslog, you can send syslogs to Cisco Prime Infrastructure, but I don't recommend using it as syslog server. Please see this link for more information https://supportforums.cisco.com/thread/2179520
Please rate if this helps

Cisco Prime Infrastructure 2.0 - no traps/info are pushed from devices

Good evening,
I have setup Cisco Prime Infrastructure 2.0 and, though I have added manually my 4 network cores as devices without any problem, I can't get a single trap or a single SNMP information to be pushed into my Cisco Prime Infra.
Here is my SNMP config on my core :
snmp-server user *edited* *edited* v3
snmp-server group *edited* v3 noauth notify *tv.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF.FFFFFFFF0F
snmp-server community *edited* RO
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps flowmon
snmp-server enable traps transceiver all
snmp-server enable traps call-home message-send-fail server-fail
snmp-server enable traps tty
snmp-server enable traps rf
snmp-server enable traps memory
snmp-server enable traps cpu_threshold
snmp-server enable traps eigrp
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps flex-links status
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps ethernet cfm cc mep-up mep-down cross-connect loop config
snmp-server enable traps ethernet cfm crosscheck mep-missing mep-unknown service-up
snmp-server enable traps ether-oam
snmp-server enable traps aaa_server
snmp-server enable traps flash insertion removal
snmp-server enable traps l2tc threshold sys-threshold
snmp-server enable traps power-ethernet police
snmp-server enable traps rep
snmp-server enable traps vswitch dual-active vsl
snmp-server enable traps udld link-fail-rpt status-change
snmp-server enable traps vtp
snmp-server enable traps vlancreate
snmp-server enable traps vlandelete
snmp-server enable traps auth-framework sec-violation
snmp-server enable traps dot1x auth-fail-vlan guest-vlan no-auth-fail-vlan no-guest-vlan
snmp-server enable traps envmon fan shutdown supply temperature status
snmp-server enable traps entity-diag boot-up-fail hm-test-recover hm-thresh-reached scheduled-test-fail
snmp-server enable traps port-security
snmp-server enable traps ethernet evc status create delete
snmp-server enable traps energywise
snmp-server enable traps ipsla
snmp-server enable traps vstack
snmp-server enable traps bfd
snmp-server enable traps bgp
snmp-server enable traps bulkstat collection transfer
snmp-server enable traps cef resource-failure peer-state-change peer-fib-state-change inconsistency
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps config-ctid
snmp-server enable traps event-manager
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps isis
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
snmp-server enable traps syslog
snmp-server enable traps isakmp policy add
snmp-server enable traps isakmp policy delete
snmp-server enable traps isakmp tunnel start
snmp-server enable traps isakmp tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps errdisable
snmp-server enable traps ethernet cfm alarm
snmp-server enable traps vlan-membership
snmp-server enable traps mac-notification change move threshold
snmp-server enable traps vrfmib vrf-up vrf-down vnet-trunk-up vnet-trunk-down
snmp-server host *ip-address-edited* version 3 noauth *edited*
Basically all traps are enabled but absolutely nothing is showing up in my Prime Infra except that my 4 devices are "Reachable".
Here is a show snmp on the same device :
sh snmp
Chassis: *S/N Edited*
38554534 SNMP packets input
    0 Bad SNMP version errors
    14 Unknown community name
    0 Illegal operation for community name supplied
    0 Encoding errors
    38453185 Number of requested variables
    0 Number of altered variables
    17790703 Get-request PDUs
    20583581 Get-next PDUs
    0 Set-request PDUs
    0 Input queue packet drops (Maximum queue size 1000)
38490708 SNMP packets output
    0 Too big errors (Maximum packet size 1500)
    0 No such name errors
    0 Bad values errors
    0 General errors
    38371069 Response PDUs
    13 Trap PDUs
SNMP global trap: enabled
SNMP agent enabled
SNMP logging: enabled
    Logging to *edited*, 0/10, 13 sent, 0 dropped.
Can anyone point out what is wrong or missing in my configuration? I can't seem to single it out myself.
Thanks
Jeremy

Hi Jeremy,
SNMP traps are shown in the events and alerts section of PI.
SNMP config looks fine. Can you run the SNMP debug (debug snmp packets ) .check the logs and see if the device is actually sending the TRAPS to the PI server.
Thanks-
Afroz
[Do rate the useful post]
****Ratings Encourages Contributors ****

Web interface on Cisco Prime Infrastructure express not coming up

Trying to get Cisco Prime Infrastructure express installed. The installation completes without any error but when I try to run show NCS or attempt to start stop the service get the following output
usdayt-cis-002/admin# show application status NCS
% Application NCS is not installed
usdayt-cis-002/admin# ncs start
sh: /opt/CSCOlumos/bin/wcsadmin.sh: No such file or directory
here's the output from show inventory
usdayt-cis-002/admin# show inventory
NAME: "Cisco-VM chassis", DESCR: "Cisco-VM chassis"
PID: Cisco-VM-SPID , VID: V01 , SN: 1GP9SNNE5HJ
Total RAM Memory: 16304916 kB
CPU Core Count: 8
CPU 0: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 1: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 2: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 3: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 4: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 5: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 6: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
CPU 7: Model Info: Intel(R) Xeon(R) CPU E5-2695 v2 @ 2.40GHz
Hard Disk Count(*): 1
Disk 0: Device Name: /dev/sda
Disk 0: Capacity: 314.50 GB
Disk 0: Geometry: 255 heads 63 sectors/track 38244 cylinders
NIC Count: 1
NIC 0: Device Name: eth0
NIC 0: HW Address: 00:50:56:AF:76:34
NIC 0: Driver Descr: e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
(*) Hard Disk Count may be Logical.
usdayt-cis-002/admin# show disks
disk: 1% used (184324 of 44628400)
temp. space 2% used (35792 of 1967952)
Internal filesystems:
all internal filesystems have sufficient free space
any idea what could be the issue here?

OK, that's the correct one. Can you verify the checksum of the file? It should be:
91dc6ebc446c1c9c000c69af4be93102
If that's OK, I would delete the VM and try installing the ova once more.
Other than that, I'd suggest calling the TAC if it's a supported installation (i.e. not an evaluation copy).

Cisco Prime Infrastructure - not updating device details

We run Cisco prime Infrastructure and I have found an interesting problem that I can't see an easy way round.
If I have say a Cisco 2950 switch on my network, managed by Prime and I upgrade it to a 3560 - I then ask Prime to re-sync the device details.
This works - you can see the updated configuration files etc but the device ID stays the same - Prime still thinks it is a 3560, which it was when the device was originally added.
Is there a way, short of deleting the device and adding it again (losing the config archive) of getting prime to update it's details to reflect the hardware change?
It came to light as it screwed up a network hardware audit I was doing - this is all showing up on Prime as the old 2050's which I have replaced with 3560's.
There must be an easier way that just deleting the device and re-adding it?

This is by no means a full solution, but deleting and re-adding only takes a few minutes if you use the "Export Device" and "Bulk Import" features from the Device Work Center. You can export the desired devices to a CSV file, delete them, then import from the CSV.
Of course, you might lose historical data when deleting the devices, but I'm guessing that's not as relevant since the devices themselves have been replaced by different hardware.

When is Cisco Prime Infrastructure 2.0 released, and what does 2.0 offer?

We are running Prime Infrastructure 1.3 primarily for wireless management at this point. We have enough licenses to add all our switches, routers, and firewalls, but we're hesitant to do so until 2.0 comes out. While there are some features for backing up and configuring switches and routers, 1.3 still seems pretty limited in regards to non-wireless features. For example, nearly every report in 1.3 is for wireless controllers or AP's, there are no reports I've found relevent for switches and routers. I've read a lot of blogs, cisco posts, and white papers talking about how Cisco Prime Infrastrucure 2.0 will finally consolidate Prime into a truly all-in-one network management suite that can manage the entire Cisco environment. Does anyone know when it's officially being released? Does anyone have an tech sheets on what's new in 2.0, or what its capabilities are? I want to better understand what 2.0 has to offer, when it's coming out, how to upgrade, so I can start planning for the upgrade and eventually importing all our network devices to Cisco Prime for centralized management. Any useful information or links would be appreciated.
Thanks,
Christian

PI 2.0 is in Beta mode for testing in closed group already. However it may still take some time to get released on CCO for FCS.
I think it is expected to be released between aug-sep. BU has also started working on CPI 2.1, which you can see test uploads on CCO.
For what does it have for customers?
> As Cisco have a vision of one network Management software for both wired and wireless infrastructure, which started getting real partially with Cisco PI.
As WCS got evolved to NCS and eventually to Cisco Prime Infrastructure, but it doesnt yet have full Management capability for wired infra., which is there with LMS.
With CPI 2.x Cisco plans to blend entire LMS and WCS features together.
-Thanks

Ciscoworks LMS 3.0 to Cisco Prime Infrastructure LMS 4.2

In order to complete the upgrade the LMS 3.x runs over a physical server that ends with the upgrade(server its gona be retired), the think is that the Cisco Prime comes with an UCS and its gona run over a VM. The question here is the "Cisco Prime Infrastructure 1.1 - Maj Upg from LMS 2.x/3.x" media could be runs as clean install, I mean with no LMS 3.x intalled before? an the "Prime Infrastructure LMS 4.2 - 1.5K Device Maj Upg Lic" could be registered with no license installed of LMS 3.x?

There are a couple of things to distinguish:
1. The product SKU you need to order to migrate from LMS 3 to LMS 4.2.
2. The license file that is installed on that new LMS server.
#1 is based on Cisco agreeing, usually through the partner or reseller you are working with, that you are entitled to order the upgrade SKU (vs. buy a complete new product). The upgrade SKUs are all listed in the ordering guide here.
L-PI12-1.5K-UP (note - NOT the 1.1 product description you noted in the original post) would be the SKU for a major upgrade from LMS 2.x/3.x to the current Prime Infrastructure 1.2 release at the 1500 device license level. That upgrade includes licenses for both PI 1.2 and Prime LMS 4.2. You may choose which to install - most LMS customers stick with LMS for now as PI 1.2 does not yet have full feature parity. Your managed devices should not exceed 1500 combined (in this case) but that combined number is not enforced technically by the product's license daemon.
Once you have purchased the product and have the media you can install it on any host that meets the installation prerequisites as far as OS, memory, disk etc. A clean installation of LMS does not check for or require a previous installation as far as technical checks.
#2 - Once you have installed the new LMS server (and optionally a step near the end of installation, you need to add in the license file (*.lic file). That is obtained through the Cisco licensing portal (or via the TAC if you prefer) using the Product Activation Key (PAK) received with your product.

CISCO PRIME INFRASTRUCTURE 1.2 NCS ERROR

Hi everyone,
can anyone put through on this, i'm having issue starting the ncs server on cisco prime infrastructure 1.2 .below is the message i get when i do show ncs status:
NGPHC-CPR001/admin# ncs status
Health Monitor is running, with an error.
failed to start NCS on startup Health Monitor
Reporting Server is running
Ftp Server is running
Database server is running
Tftp Server is running
Matlab Server is running
NMS Server is stopped.
SAM Daemon is not running ...
DA Daemon is not running ...
Syslog Daemon is not running ...
status
thanks.

Hi Marvin,
Its has never worked. This is the first time i am installing it.
I haved done as you adviced but still getting the same error as stated above.
Please is there another way out.
thanks.

Ask the Expert: Cisco Prime Infrastructure - Implementation and Deployment

Welcome to the Cisco Support Community Ask the Expert conversation.
This Ask The expert Session will cover questions spanning Cisco Prime Infrastructure on Implementation and Deployment on Wired and Wireless. This will be more specific to Customer’s and Partners questions product covering PI on configuration, Features and Menu, Network Monitoring, Maps, Implementation, High Availability and Maintenance and t/s parts.
Monday, February 2nd, 2015 to Friday, February 13th, 2015
Dhiresh Yadav is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco Prime Infrastructure and Cisco Wireless products. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS) and CCIE (DC) certifications.
Afroz Ahmad is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 7 years of industry experience working with large enterprise and service provider networks. He also holds CCNP (RS),CCIE (DC), and SCJP (Sun Certified Java Professional )
Vinod Kumar Arya is a customer support engineer in High-Touch Technical Services (HTTS) handling supporting Wireless and Network Management based Cisco products and is based in Bangalore. His areas of expertise include Cisco NMS products like Prime Infrastructure, LMS, IP SLA and SNMP etc. He has over 8 years of industry experience working with large enterprise and service provider networks. He also holds VCP 5 and RHCE certifications.
** Remember to use the rating system to let the experts know you have received an adequate response.**
Because of the volume expected during this event, the experts might not be able to answer every question. Remember that you can continue the conversation in the Network Infrastructure community, > Network Management, shortly after the event. This event lasts through February 13th 2015. Visit this forum often to view responses to your questions and those of other Cisco Support Community members.

Hello Wilson,
Thanks for joining us.
1841 should just work fine for net flow . Hope you have a valid "PI Assurance license" installed on the server.
"PI Assurance license" is required for "net-flow" feature
Devices supporting Netflow in PI ::
1400, 1600, 1700 & 1800
2500, 2600 & 2800
3600, 3700, 3750 & 3800
4500 & 4700
AS5300 & 5800
7200, 7300, 7400 & 7500
Catalyst 4500 ASCI
Catalyst 5000, 6500, & 7600 ASCI
ESR 10000 ASCI
GSR 12000 ASCI
Cisco IOS Software Release Version
Supported Cisco Hardware Platforms
11.1CA, 11.1CC
Cisco 7200 and 7500 series, RSP 7200 series
12.0
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series
12.0T, 12.0S
Cisco 1720, 2600, 3600, 4500, 4700, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8600 series
12.0(3)T, 12.0(3)S
Cisco 1720, 2600, 3600, 4500, 4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)T
Cisco 1400, 1600, 1720, 2500, 2600, 3600, 4500,
4700, AS5300, AS5800
RSP 7000 and 7200 series
uBR 7200 and 7500 series
RSM series, MGX8800RPM series, and BPx8650 series
12.0(4)XE
Cisco 7100 series
12.0(6)S
Cisco 12000 series
NetFlow is also supported by these devices Cisco 800, 1700, 1800, 2800, 3800, 6500, 7300, 7600, 10000, CRS-1 and these Catalyst series switches: 45xx, 55xx, 6xxx.
NetFlow export is also supported on other Cisco switches when using a NetFlow Feature Card (NFFC) or NFFC II and the Route Switch Module (RSM), or Route Switch Feature Card (RSFC). However, check whether version 5 is supported, as most switches export version 7 by default.
You can check the below steps to diagnose the issue::
To verify that NetFlow is exported from a device to PI, follow the steps below:
1)   Browse to Administration > Data Sources page. Check the value in column ‘Last Active Time’ for the ‘Device Data Sources’ table. If the table is empty or the value does not represent recent time, then
it is possible that the device is not exporting NetFlow or PI Assurance license is not applied / expired.
2)   Login to PI console ( via SSH) as root user and run the command:
                netstat –an | grep 9991 – Output of this should be like : udp        0      0 :::9991         :::*
                Check the firewall settings on PI server using the command: firewall -L
1)   Check the configuration on an IOS / IOS –XE device. Run the commands
a)   sh running-config | inc destination
1)   This should list the IP address of the PI SERVER ( along with other outputs if any)
b)   sh running-config | inc 9991
1)   This should list at least one entry.
c)   If the above are fine, then verify that the flow monitor, flow exporter and the flow records are correctly configured on the device.
Refer to the URLs below to configure NetFlow export.
http://preview.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/user/guide/setup_monitor.html#wp1056427
Thanks-
Afroz
***Ratings Encourages Contributors ****

Cisco Prime Infrastructure 1.4 SNMP Traps are not converted into Alarms

Hi everybody,
I just configured SNMP Traps on a Cisco Catalyst 3750-x to send to our Cisco Prime Infrastructure 1.4 Appliance.
Now I forced the Switch to send some traps (Power off a Power Supply, Interface errdisable). The only events I see in Alarms & Events on PI is the same information message everytime:
Configuration management event has been recorded in ccmHistoryEventTable.
I think the forced traps should be converted into alarms? Why can't I see them?
Thanks,
Marc

Ok, I started debugging as you said. I get the following output:
Mar 13 09:28:13.711: SNMP: V2 Trap, reqid 11689, errstat 0, erridx 0
sysUpTime.0 = 198609846
snmpTrapOID.0 = ciscoSyslogMIB.2.0.1
clogHistoryEntry.2.1688 = PM
clogHistoryEntry.3.1688 = 5
clogHistoryEntry.4.1688 = ERR_RECOVER
clogHistoryEntry.5.1688 = Attempting to recover from bpduguard err-disable state on Gi1/0/13
clogHistoryEntry.6.1688 = 198609844
Mar 13 09:28:13.737: SNMP: Queuing packet to xx.xx.xx.xx
Looks like the Switch is sending SNMP Traps from the ciscoSyslogMIB. Is this why PI can't show the Traps and convert it into a alarm?
After this test I configured logging (syslog) to the PI. Now the errors are showed but still not converted into alarms. I just want to be notified by email when such errors occurs.
Thanks,
Marc

Cisco Prime Infrastructure 1.2 licensing

I have a customer that is running CiscoWorks 3.2 and they also have NCS 1.1 (upgraded from WCS 7.0). They have found that it costs way more to upgrade CiscoWorks to Cisco Prime Infrastructure than it would be to just buy licenses after they finish upgrading NCS to Cisco Prime 1.2.
The main question about Cisco Prime 1.2 is how the licensing works, we need to know if the licensing will work the same as it did for CiscoWorks where they only needed one license for a full stack of switches. They believe that Prime 1.2 will require a license for each switch in the stack, which will cause them to buy several more licenses than what they feel they can afford.
If anyone knows how the licensing works, it would be appreciated.
Thanks.

Have you gone through the below link
http://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/prime-infrastructure/guide_c07-714720.html

Full "show run" output on Cisco Prime Infrastructure

Similar Messages

Maybe you are looking for