Fully controlled bridge

Hi:
I need some help. I gonna control the speed of DC motor, so I gonna use a single-phase fully controlled bridge rectifier. I have a NI USB-6008, with it a goona make the pulses to the scr's; so I need to know how can I synchronize this pulses with the frecuency of the source??, and how can I move this pulses to vary the speed?.
Thank you

If you can find the zero cross, you can synchronize your pulses, wherever you want as the frequency is stable, 50 Hz (or 60Hz).
You just measure time inside one half-period. Then another zero cross will occur, and you restart measuring time.
The only thing i am not sure, is that you probably need a real-time software to do that. If you rely on windows... you will have problems, for sure...
Message Edited by Pnt on 05-05-2008 08:17 AM

Similar Messages

ARD 3.6.1 - unable to fully control a client over the web

I am controling a mac mini at a remote location.
I have the remotre system set up using DYNDNS. The router at that location has ports 3283 and 5900 open, pointing towards the IP of the mac mini. Remote Access is enabled with all priviledges checked.
I am able to set up the connection as well as see and control the machine - no problem.
I am however uable to copy files, install packages, update client software and generate reports. ARD tell me the system does not support that procedure.
Any advice on this?
Thanks in advance,
Tobias
Mac OSX 10.8.3
ARD 3.6.1

Ok, now I am getting a different message, when trying to copy a file to the machine saying that the ARD Client is not active....
How do I activate it?
ARD Client 3.6.2. ist installed, Remote Management in System Preferences is active....
Any advice?

Speedfan control of "CPUFAN"

I am talking about a Z68A GD55B3 at the moment, but this issue dates back at least to P35 boards. I cannot control CPUFAN from within speedfan. SYSFAN1 is also a 4-pin header, yet I can control the speed of it. It doesn't matter if I turn on fan control in the BIOS or not, it seems that software control of CPUFAN is blocked. Is there any way around this? I need it to act like the other 4-pin header (SYSFAN1).
Thanks in advance for input!

All your posts are absolutely correct. But allow me to explain what I would like to do and please give it consideration.
I have not seen any aftermarket controllers that offer software control, but I'm open to suggestions. I'm not interested in going to the machine and turning the fans on every time it goes from idle to heavy use, and back off again after. Not to mention if I forget and overheat it.
My goal is to have a passive system at idle. This is far from unreasonable, with c-state, c1e and Intel's turbo function... If you have a decent HSF on a sandy bridge CPU, you might even get away with fanless under load, though I have not tested that. You can even get fairly powerful video cards with fanless heatsinks now. If you can, why not? It's quiet, saves power and fan life, and lessens the need to open a case and clean heatsinks.
I connected a 4-pin fan to the CPUFAN header and I can control it, but I don't know of any 4-pin (PWM) fans that will stop completely. I can fully control a 3-pin fan from the (also 4-pin) SYSFAN1 header, which leads me to believe that not being able to control a 3-pin fan on the CPUFAN header is a "feature" for safety and not a hardware limitation of 4-pin headers. Is it the intent of MSI to prevent people from unwittingly cooking something? If so, I understand, but I would like to lobby for a BIOS setting to bypass this. The past 5 to 10 MSI boards I have purchased have not allowed variation of a 3-pin fan on the CPUFAN header. My old P35 board allows control of 3 sysfan headers but newer MSI boards only have control of 2, so I need that CPUFAN header more.
I have Abit and Asus boards that coincide (chipset-wise) with the MSI boards that don't allow 3-in control of the CPU header. I will test them to see if this is just an MSI thing or if it's industry wide. Passive cooling has merit, and I believe passive at idle is the wave of future. GPUs and CPUs are more and more efficient every year, I'd like to see better options than 4-pin fans that will only slow to 600RPMs from MSI. So my question now is, is there a physical difference between CPUFAN and SYSFAN1 (both 4-pin), and if not, could we lobby for a new setting in the BIOS that would allow CPUFAN to act just like SYSFAN1?

Adobe Bridge CC not playing After Effects CC animations

Hello,
I am fairly new to After Effects and Adobe Bridge, and I recently ran into a problem.
So, when I turn on After Effects , and in the Effects Panel , I click "Browse Presets", and then It opens Adobe Bridge. But when I single-click in any kind of an animation in Bridge, it's not playing it in the "Preview" panel.
The little Windows's "picture icon" just starts zoomed in, and then it quickly zooms out.
I'm using a freshly installed Windows 8.1 , and fully updated Bridge and After Effects.
What might be the problem?
If you want, I could also record the problem with a screen recorder and upload it to YouTube.
EDIT : I just fixed the problem by updating Bridge to the latest version (CC 6.1)!
The animations are playing smoothly without any problems! Just run the Adobe Update Manager, and update
Bridge!
Edited by Michael Jackson, 1999.

Hi,
Please refer to the help document below:
CC applications close immediately after launch
Regards,
Sheena

Bridge to PS CC 2014: Error "Windows Cannot Find Photoshop CC" for PSD & TIFF files

Since installing PS CC 2014, I have been unable to open PSD & TIFF files from within Bridge. If I do- I get the error above. Once Photoshop CC 2014 was installed, I removed the older version of PS CC.
Sounds like a registry issue created when PS CC 2014 installed alongside PS CC; confusing Bridge of where to send Photoshop files.

Looks like bridge is still trying to run the old version. Did you uninstall Photoshop CC after installing Photoshop CC 2014?
Have you made sure and fully closed Bridge and reopened it? Logging off and back on would ensure that.
Failing the above, people have reported success with using the Creative Cloud Cleaner tool followed by a reinstall of Photoshop CC 2014...
Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6
-Noel

Windows cannot find Photoshop CS5 Error in Bridge

This is really about Photoshop CS6 Beta but this error is generated whenever I tried to open a file from Bridge, either Bridge [12.1 or 13.0]. It was frustrating at first.
I tried to figure out why I was receiving this message. Originally, I had Photoshop CS5 on my system. Then, I upgraded to Photoshop CS5 Extended. Finally, I installed Photoshop CS6 Beta. After the last install, I decided to uninstall Photoshop CS5 which I no longer used. These are 64-bit programs but I doubt that makes a difference. Whenever I opened Bridge for Photoshop CS5 Extended or Photoshop CS6 Beta, the shown error would generate. After reviewing the error closely, I decided to try and look at file associations but not in Windows as I had no problems elsewhere. It must be in Bridge.
I went to Edit -> Preferences and found a File Type Associations section with every file type it uses. Sure enough, by clicking on the triangle to the right of the file type, it showed only Photoshop. By clicking on Browse and going to the Photoshop CS6 Beta folder, I was able to change a couple of the ones I use exclusively and clicked OK. Afterwards, no problems. To change each and every one of those is going to require some time on my part.
This brings up an important question regarding upgrades. I think most of us upgrade before uninstalling the old version. Here are my questions:
1. Why did not the Bridge associated with the extended version change the file associations to the appropriate version of CS5 when it was installed?
2. Why did not the Bridge associated with Photoshop CS6 Beta change the file associations to this version when installed?
At the very least, it should be an option but I think it should actually point to the new version. Is this a bug in the Bridge software? I know Bridge is used for other Adobe applications but this definitely seems to be a bug when the only application iis Photoshop. I have Lightroom 4 also installed but this application does not use Bridge. Can this be corrected?

Looks like bridge is still trying to run the old version. Did you uninstall Photoshop CC after installing Photoshop CC 2014?
Have you made sure and fully closed Bridge and reopened it? Logging off and back on would ensure that.
Failing the above, people have reported success with using the Creative Cloud Cleaner tool followed by a reinstall of Photoshop CC 2014...
Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6
-Noel

Bridge-group 1 in a WLAN environment

I'm configuring some AP 1130 AG.
For customer requirements I cannot use the VLAN 1 but in particular a VLAN 102 for the management and the VLAN 117 for the WiFi users. At this point I configured the switch port in trunk with the vlan 117 and 102 as native. In the AP I configured a fast ethernet interface0,vlan- id with the vlan-id ugual to the native vlan (102) I wrote also encapsulation dot1q 102 native. As bridge-group I tried to leave the bridge-group 1 but I lost the connection. If I put as bridge-group 102 all is ok. Why? I know that It is not necessary to specify the bridge group to which the FastEthernet interface 0.native_vlan_number belongs. It will be associated by default to the bridge group 1 used for the administration of the access point. I don't understand why? is there a link between bridge group 1 and vlan 1 (that I put down in the switch)?

Thank you very much!
Here a piece of the conf:
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 117 mode ciphers tkip
ssid XYZ
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.102
encapsulation dot1Q 102 native
no ip route-cache
bridge-group 102
bridge-group 102 subscriber-loop-control
bridge-group 102 block-unknown-source
no bridge-group 102 source-learning
no bridge-group 102 unicast-flooding
bridge-group 102 spanning-disabled
interface Dot11Radio0.117
encapsulation dot1Q 117
no ip route-cache
bridge-group 117
bridge-group 117 subscriber-loop-control
bridge-group 117 block-unknown-source
no bridge-group 117 source-learning
no bridge-group 117 unicast-flooding
bridge-group 117 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 117 mode ciphers tkip
encryption vlan 102 key 1 size 128bit 7 D27D726E54606C44B67B17586243 transmit-key
encryption vlan 102 mode wep mandatory
ssid ITC
no dfs band block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.102
encapsulation dot1Q 102 native
ip address 172.44.12.20 255.255.255.0
no ip route-cache
bridge-group 102
no bridge-group 102 source-learning
bridge-group 102 spanning-disabled
interface FastEthernet0.117
encapsulation dot1Q 117
ip address 172.44.17.20 255.255.255.0
no ip route-cache
bridge-group 117
no bridge-group 117 source-learning
bridge-group 117 spanning-disabled
interface BVI1
no ip address
no ip route-cache
ip default-gateway 172.44.17.1
radius-server host 172.21.3.2 auth-port 1812 acct-port 1813 key 7 adafsgvvf1234r
radius-server host 172.25.3.22 auth-port 1812 acct-port 1813 key 7 144fghnjgrgregh
bridge 1 route ip
Switch port configuration:
interface FastEthernet1/0/21
description To AP1130
switchport trunk encapsulation dot1q
switchport trunk native vlan 102
switchport mode trunk
switchport nonegotiate

1242AG Bridge, VLAN and Multiple SSIDs

I have two buildings that I'm trying to configure a bridge in between them using 2 1242AG APs.
Building A
PCOFFICE SSID on VLAN 200 Radio G
ROOT_1 SSID on Native VLAN 1 Radio A
Root Bridge
Building B
FDAPC SSID on Native VLAN 1 Radio G
ROOT_1 SSID on Native VLAN 1 Radio A
We are using directional antenna. I know they are lined up properly because I have them both down and in front of me. I'm getting an error on the Building B AP that says "
No SSID with VLAN configured. Dot11Radio1 not started." and I'm unable to get this to work. The bridge was working before I added the VLAN and encryption/WPA information for the PCOFFICE and FDAPC SSIDs
Any assistance would be amazing. Thanks! Please see attached files for configurations. I know the switch is configured properly because I had this working before and forgot to save the damn configuration off the devices. I'm not having to do it over from scratch.

That did not work.
I've managed to fix the ROOT_1 and FDAPC... now I'm having an issue where I can attempt to connect to the PCOFFICE SSID but I'm unable to get a DHCP address from the server.
Here is the config for the AP with PCOFFICE on it and the switch.
SWITCH
interface GigabitEthernet3/2
switchport trunk allowed vlan 1,200
switchport mode trunk
interface Vlan1
ip address 192.168.3.4 255.255.255.0
interface Vlan200
ip address 192.168.30.2 255.255.255.0
ip helper-address 192.168.3.98
ip default-network 192.168.3.0
ip route 0.0.0.0 0.0.0.0 192.168.3.1
no ip http server
ACCESS POINT
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP1_ROOT_AP
enable secret 5 REMOVED
ip subnet-zero
no aaa new-model
dot11 vlan-name VLAN1 vlan 1
dot11 vlan-name pcCopper vlan 200
dot11 ssid PCOFFICE
   vlan 200
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 REMOVED
dot11 ssid ROOT_1
   vlan 1
   authentication open
   authentication key-management wpa
   infrastructure-ssid optional
   wpa-psk ascii 7 REMOVED
dot11 network-map
dot11 arp-cache optional
power inline negotiation prestandard source
username Cisco password 7 REMOVED
username admin privilege 15 password 7 REMOVED
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
encryption vlan 200 mode ciphers tkip
ssid PCOFFICE
speed basic-2.0 5.5 11.0 12.0 18.0 24.0 36.0 48.0 54.0
no power client local
power client 17
power local cck 17
power local ofdm 17
channel 2462
station-role root access-point
antenna receive right
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 port-protected
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.200
encapsulation dot1Q 200
no ip route-cache
bridge-group 200
bridge-group 200 subscriber-loop-control
bridge-group 200 block-unknown-source
no bridge-group 200 source-learning
no bridge-group 200 unicast-flooding
bridge-group 200 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption mode ciphers tkip
encryption vlan 1 mode ciphers tkip
ssid ROOT_1
dfs band 3 block
speed basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0
no power client local
power client 11
power local 11
channel 5180
station-role root bridge
antenna receive right
antenna transmit right
interface Dot11Radio1.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
hold-queue 160 in
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0.200
encapsulation dot1Q 200
no ip route-cache
bridge-group 200
bridge-group 200 spanning-disabled
interface BVI1
ip address 192.168.3.241 255.255.255.0
no ip route-cache
ip default-gateway 192.168.3.1
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
control-plane
bridge 1 route ip
line con 0
line vty 0 4
login local

Cisco 877w -Configuration of subinterfaces and main interface within the same bridge group is not permitted

Hi,
I have another problem - after upgrade ios wirelles connection not work.
After reload i have :
Configuration of subinterfaces and main interface
within the same bridge group is not permitted
STP: Unable to get the port parameters.
Please configure the bridge group on this interface first.
Please configure the bridge group on this interface first.
Please configure the bridge group on this interface first.
SETUP: new interface NVI0 placed in "shutdown" state
my old configuration work propertly in the old software, but after update i have notificatio.
Old thread:
https://supportforums.cisco.com/discussion/12379491/cisco-877w-no-wireless-connection
my current sh run:
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
service password-encryption
hostname cisco
boot-start-marker
boot system flash:c870-advipservicesk9-mz.124-24.T6.bin
boot-end-marker
logging message-counter syslog
logging buffered 4096 informational
enable secret 5 $1$eCNp$rWuBfZ/cexnwnkm7L447s.
aaa new-model
aaa session-id common
dot11 syslog
dot11 ssid ciscowifi
vlan 1
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 050D031D26595D0617
dot11 wpa handshake timeout 500
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.56.1
ip dhcp pool CLIENT
import all
network 192.168.56.0 255.255.255.0
default-router 192.168.56.1
dns-server 8.8.8.8 194.204.159.1 194.204.152.34
lease 0 2
ip cef
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
username marek password 7 00121A0908500A
archive
log config
hidekeys
ip tcp path-mtu-discovery
bridge irb
interface ATM0
description Polaczenie ADSL do ISP$ES_WAN$
no ip address
no atm ilmi-keepalive
pvc 0/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
hold-queue 224 in
interface FastEthernet0
description Edzia
interface FastEthernet1
description dom
interface FastEthernet2
description Dziadek
interface FastEthernet3
interface Dot11Radio0
no ip address
no ip redirects
ip local-proxy-arp
ip nat inside
ip virtual-reassembly
no dot11 extension aironet
encryption vlan 1 mode ciphers tkip
encryption mode ciphers aes-ccm tkip
broadcast-key change 3600
ssid ciscowifi
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
world-mode dot11d country AU indoor
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.1
description ciscowifi
encapsulation dot1Q 1 native
no cdp enable
interface Vlan1
no ip address
bridge-group 1
interface Dialer0
description Interfejs dzwoniacy
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp chap hostname [email protected]
ppp chap password 7 xxxxxxxxxxxxxxxxxxxxxx
interface BVI1
description Polaczenie dla sieci LAN
ip address 192.168.56.1 255.255.255.0
ip nat inside
ip virtual-reassembly
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
no ip http secure-server
ip nat inside source list 100 interface Dialer0 overload
ip nat inside source static tcp 192.168.56.10 80 interface Dialer0 80
ip nat inside source static tcp 192.168.56.10 22 interface Dialer0 22
logging trap debugging
logging 192.168.56.10
access-list 100 permit ip 192.168.56.0 0.0.0.255 any
access-list 100 deny ip any any
no cdp run
snmp-server community ciskacz RO
snmp-server chassis-id ciskacz
control-plane
bridge 1 protocol ieee
bridge 1 route ip
line con 0
no modem enable
line aux 0
line vty 0 4
exec-timeout 0 0
transport preferred ssh
transport input ssh
scheduler max-task-time 5000
end
please help - thanks!

Hello Marek,
I suppose you are not planning to do any kinds of advanced config using several VLANs and multiple SSIDs so let's just make your configuration simple and working.
In short, you need to remove all references to VLAN 1 and to any subinterfaces possibly related to the VLAN 1. This means in particular (follow these steps in sequence):
Remove the Dot11Radio0.1 subinterface entirely
In the Dot11Radio0 section, remove the encryption vlan 1 mode ciphers tkip command
In the dot11 ssid ciscowifi section, remove the vlan 1 command
After performing these steps, make sure that the ssid ciscowifi and encryption mode commands are still present in the Dot11Radio0 configuration, and if not, reenter them.
Best regards,
Peter

Bridge with 2 x Aironet 2602e

Hi -
I'm trying to configure two Aironet 2602e (with external antennas) to form a bridge between two buildings. I can't figure out how to get them to run faster than 54 Mbit between them. Currently they just sit at my desk in a test-setup. I think, I should maybe set them up as Workgroup-bridges instead of root-to-non-root, but I don't get other speed options than those 54 Mbit. Also I think it should be done at 5 GHz radio.
Could it be something with encryption mode or is it only possible through CLI or...
Please help
Sincerly
Nicholas

That was a fast response!
My config (too much of it??):
dot11 syslog
dot11 ssid Gangbro3
   authentication open
   authentication key-management wpa version 2
   wpa-psk ascii 7 0100525750585400751842594900
crypto pki token default removal timeout 0
username administrator privilege 15 password xxxxxxxxxxxxxxxx
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
shutdown
encryption mode ciphers aes-ccm
antenna gain 0
speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. m16. m17. m18. m19. m20. m21. m22. m23.
station-role root access-point
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid Gangbro3
antenna gain 0
no dfs band block
stbc
speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. m16. m17. m18. m19. m20. m21. m22. m23.
channel dfs
station-role root bridge
bridge-group 1
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip forward-protocol nd
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
transport input all
end

DHCP over wireless bridge

I want to setup a wireless bridge going from a current network (siteA), to a new small network across the street (siteB). I have 2 Cisco 1131AG Access points. I have no need for any client access, only the bridge. I have the interfaces up and can ping across, however, no dhcp requests seem to come over the bridge. Where am I going wrong??
[SiteA]
dot11 ssid Cisco
authentication open
authentication key-management wpa
guest-mode
infrastructure-ssid
wpa-psk ascii secret
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid Cisco
station-role root access-point
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 10.175.36.254 255.255.255.0
no ip route-cache
bridge 1 route ip
[SiteB]
dot11 ssid Cisco
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii secret
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid Cisco
station-role workgroup-bridge
bridge-group 1
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address 10.175.36.253 255.255.255.0
no ip route-cache
bridge 1 route ip
bridge 1 aging-time 120

Have you tried configuring Site A as root bridge and Site B as non-root bridge.
See this example:
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008058f53e.shtml

1941W bridge issues

I'm trying to setup a (what I think to be) simple wireless network using a Cisco 1941W integrated services router. Currently running this on a test environment behind a little Linksys router/modem combo (at 192.168.0.1). I would like to use the 2.4ghz radio as a root access point for clients to gain access to both the wired network (currently at 192.168.2.0) and the external network (currently at 192.168.0.1). Wireless clients are set to 192.168.1.X.
I can ping external IPs from the router (ie google.com), ping all the interfaces on the AP (BVI interface and clients). From the AP I can ping all the interfaces on the router, I can't however leave the router at all (ie ping 192.168.0.1, google). Been playing with this for a while so there might be some extras in my config but:
Router Config:
! Last configuration change at 22:59:21 UTC Thu Aug 5 2010
version 15.0
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname YTCamsRouter
boot-start-marker
boot-end-marker
enable secret 5 $1$..KB$Qa/M2FDZkxqAHydIMyFDk1
no aaa new-model
service-module wlan-ap 0 bootimage autonomous
no ipv6 cef
ip source-route
ip cef
ip dhcp excluded-address 192.168.1.1 192.168.1.99
ip dhcp excluded-address 192.168.1.201 192.168.1.254
ip dhcp pool ytexternal
   network 192.168.1.0 255.255.255.0
   default-router 192.168.1.1
   dns-server 192.168.1.1
ip name-server 8.8.8.8
ip name-server 4.4.4.4
ip name-server 192.168.0.1
multilink bundle-name authenticated
license udi pid CISCO1941W-A/K9 sn FHK140573YT
username SAadmin privilege 15 secret 5 $1$izd3$bv13qI3qWRcgT6a7YivWc1
interface Wlan-GigabitEthernet0/0
description Internal switch interface connecting to the embedded AP
interface GigabitEthernet0/0
description internal interface
ip address 192.168.2.1 255.255.255.0
ip access-group from-lan in
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered Vlan1
arp timeout 0
no mop enabled
no mop sysid
interface GigabitEthernet0/1
description external interface
bandwidth 1000
ip address 192.168.0.200 255.255.255.0
ip access-group from-lan out
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
interface FastEthernet0/0/0
no ip address
shutdown
duplex auto
speed auto
interface FastEthernet0/0/1
no ip address
shutdown
duplex auto
speed auto
interface Vlan1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
no ip http server
no ip http secure-server
ip route 0.0.0.0 0.0.0.0 192.168.0.1
ip access-list extended nat-list
permit ip 192.168.0.0 0.0.0.255 any
permit tcp 192.168.1.0 0.0.0.255 any
control-plane
line con 0
password xxxxx
login
line aux 0
line 67
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
password xxxxxx
login
scheduler allocate 20000 1000
end
AP Config:
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
no logging buffered
enable secret 5 $1$iTve$jLo12l8pXiW6fzZ34B5fg1
no aaa new-model
dot11 syslog
dot11 ssid YTGuest
   vlan 1
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 033D0B1E080832581E1E17
username Cisco password 7 01300F175804
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
encryption vlan 1 mode ciphers aes-ccm
ssid YTGuest
antenna gain 0
station-role root access-point
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
antenna gain 0
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
no ip route-cache
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.1.3 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
no activation-character
line vty 0 4
login local
end
show ip route from the router:
YTCamsRouter#show ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route, + - replicated route
Gateway of last resort is 192.168.0.1 to network 0.0.0.0
S*    0.0.0.0/0 [1/0] via 192.168.0.1
      192.168.0.0/24 is variably subnetted, 2 subnets, 2 masks
C        192.168.0.0/24 is directly connected, GigabitEthernet0/1
L        192.168.0.200/32 is directly connected, GigabitEthernet0/1
      192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
C        192.168.1.0/24 is directly connected, Vlan1
L        192.168.1.1/32 is directly connected, Vlan1
      192.168.2.0/24 is variably subnetted, 2 subnets, 2 masks
C        192.168.2.0/24 is directly connected, GigabitEthernet0/0
L        192.168.2.1/32 is directly connected, GigabitEthernet0/0
YTCamsRouter#
Just for good measure, a show IP Interfaces brief from the router
Interface                  IP-Address      OK? Method Status                Prot
ocol
Wlan-GigabitEthernet0/0    unassigned      YES unset up                    up
GigabitEthernet0/0         192.168.2.1     YES manual up                    up
wlan-ap0                   192.168.1.1     YES TFTP   up                    up
GigabitEthernet0/1         192.168.0.200   YES manual up                    up
FastEthernet0/0/0          unassigned      YES NVRAM administratively down down
FastEthernet0/0/1          unassigned      YES NVRAM administratively down down
Vlan1                      192.168.1.1     YES NVRAM up                    up
NVI0                       192.168.2.1     YES unset up                    up
YTCamsRouter#
Thanks in advance.

Hi Jeff,
I don't see a default gateway configured on the ap.
looks like it should be 192.168.1.1

1252 Access point bridge problems

Hello
Currently im trying to deploy solution for external people as somethink like quest connection (in config name is public.net)
The only spare AP i have is cisco 1252
After research in setup whitchport as trunk for management vlan (which must be done) and for me entire config seems to be good. Im able to connect to ssid, but im unable to browse web, when connected.(still receiving 169. ip addres)
Im able to ping default gateway,able to ping dhcp server. Think is, when checking bridge, receiving is ok, but nothing is being transmitted.
Vlan 192 is our vlan just for public conenction, works correctly on other aps.
Btw same problem is have with 1142.
I think there must me missing something specific for this two models (as was that management vlan must be native on switch side)
any ideas please?
dot11 ssid public.net
vlan 192
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 0 on2access@wpa!
dot11 aaa csid ietf
dot11 network-map 60
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 192 mode ciphers tkip
ssid public.net
speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
channel 2412
station-role root
rts threshold 2312
world-mode dot11d country SK both
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.192
encapsulation dot1Q 192
no ip route-cache
bridge-group 192
bridge-group 192 subscriber-loop-control
bridge-group 192 block-unknown-source
no bridge-group 192 source-learning
no bridge-group 192 unicast-flooding
bridge-group 192 spanning-disabled
interface Gi0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface Gi0.16
encapsulation dot1Q 16
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface Gi0.192
encapsulation dot1Q 192
no ip route-cache
bridge-group 192
no bridge-group 192 source-learning
bridge-group 192 spanning-disabled
interface BVI1
ip address 10.250.16.68 255.255.255.0
no ip route-cache

Hi
Try to add following & see
interface Gi0.16
encapsulation dot1Q 16 native
int d0.16
encapsulation dot1Q 16 native
bridge-group 1
Also if "ip default-gateway x.x.x.x" command is missing add that as well. Here is a basic configuration without any added security.
dot11 ssid TEST
vlan 143
authentication open
guest-mode
interface Dot11Radio1
ssid TEST
interface Dot11Radio1.143
encapsulation dot1Q 143
bridge-group 143
interface Dot11Radio1.999
encapsulation dot1Q 999 native
bridge-group 1
interface GigabitEthernet0.143
encapsulation dot1Q 143
bridge-group 143
interface GigabitEthernet0.999
encapsulation dot1Q 999 native
bridge-group 1
interface BVI1
ip address 192.168.99.99 255.255.255.0
ip default-gateway 192.168.99.1
HTH
Rasika
**** Pls rate all useful responses *****

Bridge looses cache folder tree window when I rename parent folder

I managed to activate the code to change the name of the parent folder containing some images (I put an underscore before de parent folder name).
When I did it by hand, the folder and subfolders I was navigating on were visible on the folder window (left side)
But I lose the navigation of folders in the left window when I do exactly the same by code.
    var newPath = decodeURI(Path.parent)+"/_"+name;
    var bt = new BridgeTalk();
    bt.target = "bridge";
    // as acções do bridge contêm 1. colocação do _   2. label 3. organização dos ficheiros por tipo
    bt.body = "app.document.thumbnail =Folder('"+newPath+"').fsName;";
    bt.send(8);
    bt.pump();
... and the left navigation desapears...
Is there same cache loosing problem? Can I recreate the last folder navigational window some how with code?

I can't believe I found it, but it works and it is simple.
At the same time, I spent 2 years using Bridge the wrong way and if I had an Adobe Bridge dev here, I wouldn't be very happy.
Why Adobe simply can't give straight and direct answers like this case?
When i rename a app.document.presentationPath, I usually returned to its parent folder on first place and then refresh() this one.
Then I would go back to the new renamed folder.
Problem:
The 'Content' panel was OK and refreshed but the 'Folders' panel was not: the last non-renamed folder was still there and I always needed to close its parent folder on 'Folder' panel, click F5, and reopen making that ghost folder to disappear.
The solution is simple and logical but sadly it took 2 years for me to solve it.
I only needed to start dealing with the node string containing a fully qualified Bridge URI (uniform resource identifier).
For example:
var origin = Folder(app.document.presentationPath);
var renamedFolderName = 'v_'+ Folder(app.document.presentationPath).name;
app.document.thumbnail = new Thumbnail(new Folder(app.document.presentationPath).parent); // back to parent folder
Folder(origin).rename(renamedFolderName ); // renaming
app.document.thumbnail.refresh(); // refreshing the parent folder
app.document.thumbnail = new Thumbnail(new Thumbnail(Folder(Folder(origin).parent + "/" + renamedFolderName ).fsName).uri); // the uri is the node (fully qualified Bridge URI)
And... the 'Folders' panel was updated correctly and the ghost folder vanished!

AP 1242AG Bridge

Hi
I'm looking for some help. I've created a wireless bridge using WGB at switch end and Root Bridge at remote end.
This worked fine, till I tried to add vlans to it.
VLAN 20 data/native and VLAN 30 Voice.
I created the VLANs on both ends and assigned to antenna. Now I'm not able to get the ping.
On the WGB AP Click on ASSOCIATION - it shows the Infrastructure 1 and the corrent OP and MAC as assaciated on vlan 20.
Click on the Root Bridge end, States Association Processing.
Any help would be great
cheers
Craig
Header 1
Header 2
WGB
Root Bridge
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
logging rate-limit console 9
enable secret 5 $1$SCCZ$laZulA7.ofnaOGc0Kw9vu1
no aaa new-model
dot11 syslog
dot11 vlan-name voice vlan 30
dot11 ssid bridge
   vlan 20
   authentication open mac-address mac_methods
   infrastructure-ssid optional
dot11 ssid vbridge
   vlan 30
   authentication open mac-address mac_methods
username Cisco password 7 01300F175804
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption key 1 size 128bit 7 D364625F7E6C49E6781D082F12A2 transmit-key
encryption mode wep mandatory
ssid bridge
ssid vbridge
station-role workgroup-bridge
world-mode dot11d country-code GB both
interface Dot11Radio0.20
encapsulation dot1Q 20 native
no ip route-cache
bridge-group 1
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption key 1 size 128bit 7 D364625F7E6C49E6781D082F12A2 transmit-key
encryption mode wep mandatory
ssid bridge
ssid vbridge
no dfs band block
channel dfs
station-role root
interface Dot11Radio1.20
encapsulation dot1Q 20 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
bridge-group 30 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.20
encapsulation dot1Q 20 native
no ip route-cache
bridge-group 1
interface FastEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
interface BVI1
ip address 10.160.10.14 255.255.255.128
no ip route-cache
ip default-gateway 10.160.10.1
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
login local
workgroup-bridge client-vlan 20
end
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
logging rate-limit console 9
enable secret 5 $1$jZV1$Su/gfThsuQ/Pdd981xL5D0
no aaa new-model
dot11 syslog
dot11 ssid bridge
   vlan 20
   authentication open mac-address mac_methods
   infrastructure-ssid
dot11 ssid vbridge
   vlan 30
   authentication open mac-address mac_methods
username Cisco password 7 072C285F4D06
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption key 1 size 128bit 7 9B10473716A854D41AAC5A3A7C4C transmit-key
encryption mode wep mandatory
ssid bridge
ssid vbridge
station-role root bridge
world-mode dot11d country-code GB both
infrastructure-client
interface Dot11Radio0.20
encapsulation dot1Q 20 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption key 1 size 128bit 7 C67646529F78224D5205272E0A71 transmit-key
encryption mode wep mandatory
ssid bridge
ssid vbridge
no dfs band block
channel dfs
station-role root
interface Dot11Radio1.20
encapsulation dot1Q 20 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
bridge-group 30 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.20
encapsulation dot1Q 20 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 spanning-disabled
interface BVI1
ip address 10.160.10.16 255.255.255.128
no ip route-cache
ip default-gateway 10.160.10.1
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
login local
end

Hi Surendra
Since sending the last post, I reset the APs again to factory setting and started again. This time I did get them to link, but they seem to now freeze, can't ping, telnet, web. LEDS showing as normal.
The config is attached , it's basic at the minute, trying to get them to say up and pass DHCP.
I'm trying to get VLANs 20 as infrasturture and VLAN 30 for Voice.
Cheers
Craig

Fully controlled bridge

Similar Messages

Maybe you are looking for