Fuzzy Buttons

I seem to be having a possible variation of the fuzzy font
problem. Whenever I test a movie, the "over state" of my buttons
appear fuzzy. This does not happen on the stage when simple buttons
are enabled. It only happens when I test the movie. Any ideas what
the problem/solution might be?

I am using Captivate 4. I have the same problem in one project I created, but not in another! I can't figure this out--to me, there is no difference between my two files. Both buttons launch a URL and the only difference I can find is that the URL, the text and location of the buttons are different between the two projects.
Assistance would be greatly appreciated. The work around is more work--which would be to use images instead of the text, and then a click box over it.

Similar Messages

Hi I have a MacBook Pro 2011 i7 and it stays on for about 4 hours then the screen go's fuzzy and I have to turn it off by the power button has anyone had this problem thanks mike

I Have a MacBook Pro i7 2011 it stays on for about 4 hours then the screen go's all fuzzy and I have to turn it off by the power button has any body else had this problem thanks mike

My guess would also be a failling connection between your logicboard and your GPU. See 2011 MacBook Pro and Discrete Graphics Card
For most users it starts with some random crashes and freezes like you describe it. And then it just gets worse and worse. There are still no "good" solutions, sadly. This is a hardware problem from the production.

Bevel button and fuzzy type

I made a button and put a simple bevel filter on it.
When I added type to the button the text bleeds into the
filter. How can I stop/fix this?

Thanks for the reply Tom. After I posted the first time I went to the Finder, Get Info, and I saw that I could change the 'Opens with' to QuickTime and therefore it became a QuickTime file. About that Anamorphic business I read a 'how to' on dealing with images before bringing them into video. The tip says in the 'New' file dialogue box to choose 640x480 size and in the pull down menu at the bottom where you can choose the 'Pixel Aspect Ratio' it was suggest to use that Anamorphic setting. I did it but it certainly didn't look right but I went with it.
Again after I posted I looked at the Format of one of the clips and saw the size to be 720x480, Compressor is DV/DVCPRO-NTSC, Pixel Aspect is NTSC-CCIR 601, Anamorphic field is blank. I'm running Photoshop CS2. So I went back there and created a new blank file to use a template for dealing with stills but this time I used the Preset pull down menu and chose NTSC DV 720x480 with guides and the Pixel Aspect Ratio automatically loaded D1/DV NTSC (0.9), clicked Ok and viola, the blank file looks exactly like the Canvas in FCE. I haven't played with a still with this new setting but I will try it on the little project I'm working on.
As for viewing it, I am looking at it on my Mac flat screen. I went into QuickTime Preferences and checked the box for high quality, thank you. Thanks for reassuring me on the file size.
I also don't know what "D4/D16 Anamorphic" means.
I don't understand the fuzzy type. I'm aware these are 72 ppi files and video is not resolution dependent but rather pixel dependent. Computer monitors display at 72 ppi, televisions are higher. I have yet to complete the process of burning a DVD and playing it back on a TV. Maybe that's where I'll see the type showing up sharper.
At any rate, just dealing with this itty bitty project tells me I have a lot to learn about video, never mind learning about how to use FCE as well.

TS1367 My mac went all fuzzy and now wont start up. When I hit the on button it simply makes a beeping noise and nothing else happens!

My mac went all fuzzy and now wont start up. When I hit the on button it simply makes a beeping noise and nothing else happens!

Here's the Apple support article on beeps https://support.apple.com/kb/HT1547

Hello Every time I create a motion menu the play buttons have a fuzzy outl

Hello
Every time I create a motion menu the play buttons have a fuzzy outline. I really don't like this and would love to know how to avoid it as it looks really bad and not crisp.
Here's how i do it:
1) I create the motion menu in AEX and add in the button here. I have the button coming in about 5 seconds after the start to give a delayed effect and this will therefore be the loop point I set in DVDSP.
2) I then export out a Photoshop layers file from AEX and then bring this file into Photoshop to make the overlay. I'm not sure if I'm doing this step correctly as I then go Image/adjustments/levels and make the play button black
3) I then make the menu an .m2v and bring this and the overlay .jpg file into DVDSP.
4) When I select the play button the edges go fuzzy. This particular PLAY button was the text PLAY in white, with a black outline. Maybe this black outline had something to do with it?? I've also had heart shaped buttons for example and this does the same thing.
Hope you can help.
Many thanks, Margie

One thing that could help is not using a .jpg which is compressed. A .tif may work better (to some degree).
Not sure if you are using text highlights or something else when you mention you make the button black. Larger text (20pt plus, Sans Serif) can often help. Part of it also may be the selection process of what you are changing. Sounds like you are sending out the highlights as a seperate layer by itself. If so you do not not to switch it to Black, depending on the color you can map it out in DVD SP.
Another thing is that if the highlight is in the motion menu (unhighlighted) the highlighing may be slightly off of the underlying item making it a bit fuzzier. Could also be colors.
On pt 4, not sure if you mean select as "I pressed the button for the action" or as just moving to the button. If the former, then there can be a slight shift as the DVD itself moves to different place. Feathering the black edges may also help....

I have been trying to crop my grandson out of a picture and make him into an 8x10. His face comes out fuzzy. I have used effects buttons-sharpness, definitionm, etc with no good results. Where should I go from there?

Using I Photo I selected a photo of two people and tried to crop one out to make an 8x10 of that person. Have tried numerouse times and have used the effects selection trying to make face clearer with no luck. cropped photo is very fuzzy.
any suggestions or just give up?

While we all have MacBooks in this forum not all of us use iPhoto. There's an iPhoto Support Community where everybody uses iPhoto. You should also post this question there to increase your chances of getting an answer.
https://discussions.apple.com/community/ilife/iphoto

Issues: extremely slow start up, occasional green fuzzy screen, doesn't always hibernate and overheats

First off, I should say that I'm not the type of person to shutdown my computer. If anything, I shut it to hiberate. I'm not sure if that's bad pratice or if that's what lead to this over time.. So here's what happens.. Today, I was working away and all of a sudden a fuzzy screen comes up with a little bit of green and then a beeping sound. So I shut it off. This is rare, sometimes the fuzzy screen comes up for a second randomly or when I open my computer from hiberate mode or when I'm just using the computer.
When I turn my computer on,
1. sometimes the 'on' button doesn't work and it takes a few tries (however this hasn't happened in the past few weeks. *knock on wood*)
Once the computer is on the blue screen comes up:
2. which stays on for anywhere from 5-20 minutes.
3. Log in appears with the cursor blinking but I actually can't type anything.. It lags behind sometimes another 20 minutes before my password appears and I could log on.
Checking the message board for similar questions it was recommended that I update the software.
I've tried to get Mavericks on here but I get an error message when it tries to restart the computer and never does so successfully on its own.
I've helped it along and was able to attempt at installing it but I waited a least an hour for it to 'find my disks' with no luck I went the disk utility repair route istead of time machine backup which couldn't find my external or anything for that matter.
The error message I got back was:
invalid block count It should be 21066078 instead of 21066076. Found corrupt needs to be repaired.
Any thoughts or advice would be helpful. Thanks in advance. Below is my EtreCheck.
Hardware Information:
    MacBook Pro (15-inch, Mid 2010)
    MacBook Pro - model: MacBookPro6,2
    1 2.66 GHz Intel Core i7 CPU: 2 cores
    8 GB RAM
Video Information:
    NVIDIA GeForce GT 330M - VRAM: 512 MB
    Intel HD Graphics - VRAM: 288 MB
System Software:
    Mac OS X 10.6.8 (10K549) - Uptime: 0 days 2:2:6
Disk Information:
    Hitachi HTS725050A9A362 disk0 : (465.76 GB)
        (null) (disk0s1) <not mounted>: 200 MB
        Macintosh HD (disk0s2) / [Startup]: 465.44 GB (80.03 GB free)
    MATSHITADVD-R   UJ-898
USB Information:
    Apple Internal Memory Card Reader
    Apple Inc. BRCM2070 Hub
        Apple Inc. Bluetooth USB Host Controller
    Apple Inc. Apple Internal Keyboard / Trackpad
    Apple Computer, Inc. IR Receiver
    Apple Inc. Built-in iSight
FireWire Information:
Thunderbolt Information:
Problem System Launch Daemons:
    [System]    org.samba.winbindd.plist 3rd-Party support link
Launch Daemons:
    [System]    com.adobe.fpsaud.plist 3rd-Party support link
    [System]    com.adobe.SwitchBoard.plist 3rd-Party support link
Launch Agents:
    [System]    com.adobe.AAM.Updater-1.0.plist 3rd-Party support link
    [System]    com.adobe.CS5ServiceManager.plist 3rd-Party support link
User Launch Agents:
    [not loaded]    com.adobe.AAM.Updater-1.0.plist 3rd-Party support link
    [not loaded]    com.adobe.ARM.[...].plist 3rd-Party support link
User Login Items:
    AdobeResourceSynchronizer
    Dropbox
Internet Plug-ins:
    AdobeAAMDetect: Version: AdobeAAMDetect 1.0.0.0 - SDK 10.6 3rd-Party support link
    FlashPlayer-10.6: Version: 13.0.0.214 - SDK 10.6 3rd-Party support link
    Flip4Mac WMV Plugin: Version: 2.4.4.2 3rd-Party support link
    AdobePDFViewerNPAPI: Version: 10.1.9 3rd-Party support link
    AdobePDFViewer: Version: 10.1.9 3rd-Party support link
    CouponPrinter-FireFox_v2: Version: Version 1.1.9 - SDK 10.5 3rd-Party support link
    Flash Player: Version: 13.0.0.214 - SDK 10.6 3rd-Party support link
    JavaAppletPlugin: Version: 13.9.8 - SDK 10.6 Outdated! Update
    QuickTime Plugin: Version: 7.6.6
    Silverlight: Version: 5.1.20513.0 - SDK 10.6 3rd-Party support link
    iPhotoPhotocast: Version: 7.0 - SDK 10.7
iTunes Plug-ins:
    Quartz Composer Visualizer: Version: 1.2
3rd Party Preference Panes:
    Flash Player 3rd-Party support link
    Flip4Mac WMV 3rd-Party support link
Old Applications:
    None
Time Machine:
    Time Machine information requires OS X 10.7 "Lion" or later.
Top Processes by CPU:
         6%    firefox
         5%    EtreCheck
         2%    hidd
         1%    WindowServer
         0%    distnoted
Top Processes by Memory:
    631 MB    firefox
    164 MB    mds
    74 MB    Mail
    74 MB    Dropbox
    57 MB    plugin-container
Virtual Memory Information:
    5.33 GB    Free RAM
    1.02 GB    Active RAM
    799 MB    Inactive RAM
    886 MB    Wired RAM
    1.30 GB    Page-ins
    0 B    Page-outs

Simska,
regarding the overheating, you can try resetting your MacBook Pro’s System Management Controller.
Regarding the invalid block count, you should boot from your grey Mac OS X Install DVD which originally came in the box with your MacBook Pro, run Disk Utility from it (via the Utilities menu in the menu bar), and select Repair Disk for your internal disk.
After your disk is repaired, exit Disk Utility and restart from your internal disk. When you log in, you should uninstall your installed version of iPhoto Photocast — it was written to work with the Lion (Mac OS X 10.7) SDK, but you have Snow Leopard (Mac OS X 10.6.8) installed, so it’s not supported under Snow Leopard. Install in its place an older version of iPhoto Photocast which is compatible with Snow Leopard. You also have an outdated version of Silverlight installed — you can download the most recent version from here.

Kernel Panic: You need to restart you computer. Hold down the Power button until it turns off, then press the Power button again.

I apologize for writing a book, but I think explaining the full story may possibly get me a correct answer. I hope that someone can give me some insight as to what is the problem with my MacBook Pro. I have a MacBook Pro (15-inch Early 2008), model identifier: MacBookPro4,1 running OSX Lion 10.7.5 with 6 GB memory. My wife first noticed a problem with the display. Every so often it would get fuzzy with jumping lines going across the screen making it vitually unviewable. The final time that incident took place the computer froze which required holding down the power button to restart the computer. The computer started up to the point of the Apple logo and the spinning gear for quite some time until the screen darkened from top to bottom displaying the following message in five different languages: "You need to restart your computer. Hold down the Power button until it turns off, then press the Power button again." I have read other blogs and support communities where people get the message intermittently, but my computer would not go past that point no matter what. Through research and the Apple Store I was told that this is a Kernel Panic. The so called "Apple Genius" at the local Apple Store was unable to get the computer to boot past that point even with his gadget. It would not startup in recovery mode, safe mode or off of a disc. I forget exacty what he told me, but he said it was getting past the first two startup steps, but it would not get past the third step which is to mount the desktop. He guessed that it may be a problem with the hard drive; a loose wire or something or other. I disconnected the hard drive completely and took it out. Everything appered to be connected properly. Then I installed it back correctly, but it did not solve the issue. So I guess I disproved his theory of a loose wire... I purchased ProSoft Data Rescue 3 and connected my MacBook Pro to another Apple computer using a firewire 400 cable. I was able to get everything I needed off of the hard drive. I did some more research and I decided to restart the MacBook Pro in verbose mode (holding down the command button and V button). The computer magically started up!!! I was upset that I wasted my money on the ProSoft Data Rescue 3. I managed to take additional items off of the computer and back it up on to an external hard drive. After some time the computer froze. I repeated the power button process to restart and received the same kernel panic. I managed to get the computer to startup approximately six or seven more times via verbose mode; each time the computer staying on for a shorter amount of time before it would freeze. I managed to run Disk Utitlity. I performed first aid to fix the hard drive and it said that the hard drive appeared to be fine. After first aid I erased the hard drive and booted off of a Lion disc to perform a clean install or an erase and install. Lion installed until the progress bar got the the end where I received a message that there was an error installing Lion, please try again. Each time I attempted to install the software I would receive the same message. Eventually the computer would not boot from the Lion disc. I went back to the Apple Store and the Apple Genius was able to get the computer to boot off of his gadget where Lion istalled completely. I set up the computer as a new computer. He said that he partitioned the hard drive as DOS and then back to Mac OS Extended (Journaled) which would get rid of any errors the drive may have had. He guessed that the problem was the hard drive, but was not exactly sure. When I brought it home I installed all of the software applications I had on it previously. Approximately three days later, which may have been the fifth of sixth time starting up the computer, the display became fuzzy again and the computer froze. The computer did restart once and I was able to retreive a "log" which I have pasted below. After if froze for the second time it restarted once using verbose mode and froze almost immediately. After holding down the power key to shut it down and then restart; I received the same kernel panic after the Apple logo and spinning gear which put me right back to square one. Now the computer will not boot via any method. It freezes at the end of verbose mode which forces you to hold down the power button to shut down. I also read that poorly seated ram may cause this issue, but I removed and installed the ram multiple times. I even purchased new ram from Other World Computing (Mac Sales) 6 GB, but that did not make a difference. I think I may see six possible problems on the verbose screen mode, five errors and one warning; I will type them out here:
1. SMC: :smcReadKeyAction ERROR: smcReadData8 failed for key $Num (kSMCKeyNotFound)
2. SMC: :smcReadKeyAction ERROR: $Num kSMCKeyNotFound(0x84) fKeyHashTable=0x0
3. SMC: :smcInitHelper ERROR: MMIO regMap ==NULL - fall back to old SMC mode
4. WARNING - ACPI_SMCCtrlLoop: :initCPUCtrlLoop - no sub-config match for MacBookPro4,1 with 8 p-states, using default stepper instead
5. SMC: :smcReadKeyAction ERROR: smcReadData8 failed for key MOTP (kSMCKeyNotFound)
6. SMC: :smcReadKeyAction ERROR: smcReadData8 failed for key BEMB (kSMCKeyNotFound)
I was hoping that someone could read my log to ascertain wether or not they see a problem that stands out. I was also hoping that someone could tell me if verbose mode provides any information that may be wrong with my computer. I just hope that someone can give me some insight as to what may be wrong with my computer. If it is the hard drive I will easily replace it, but I want to make sure that is the problem first before I waste money on a hard drive or anything else. Please let me know if anyone requires any other information from me.
Thank you!
Interval Since Last Panic Report: 21959 sec
Panics Since Last Report:          1
Anonymous UUID:                    B62D9AB4-53DD-4F76-90B2-32453302297E
Sat Aug 31 15:20:06 2013
panic(cpu 1 caller 0xffffff80002c4794): Kernel trap at 0xffffff7f81d9d774, type 14=page fault, registers:
CR0: 0x0000000080010033, CR2: 0x0000000000000010, CR3: 0x0000000011d06000, CR4: 0x0000000000000660
RAX: 0x0000000000000004, RBX: 0xffffff809eb71000, RCX: 0xffffff8000892604, RDX: 0xffffff80b69d3aa8
RSP: 0xffffff80b69d3bd0, RBP: 0xffffff80b69d3bd0, RSI: 0x0000000000000000, RDI: 0x0000000000000000
R8: 0x0000000000000000, R9: 0x00000000010751b4, R10: 0xfffffffffffffff4, R11: 0xffffff8000640fd4
R12: 0xffffff809eb71000, R13: 0x0000000000000000, R14: 0x0000000000000000, R15: 0x0000000000000010
RFL: 0x0000000000010202, RIP: 0xffffff7f81d9d774, CS: 0x0000000000000008, SS: 0x0000000000000010
CR2: 0x0000000000000010, Error code: 0x0000000000000000, Faulting CPU: 0x1
Backtrace (CPU 1), Frame : Return Address
0xffffff80b69d3880 : 0xffffff8000220792
0xffffff80b69d3900 : 0xffffff80002c4794
0xffffff80b69d3ab0 : 0xffffff80002da55d
0xffffff80b69d3ad0 : 0xffffff7f81d9d774
0xffffff80b69d3bd0 : 0xffffff7f81d8913a
0xffffff80b69d3c20 : 0xffffff7f81d89928
0xffffff80b69d3c40 : 0xffffff7f81d5be8f
0xffffff80b69d3c70 : 0xffffff7f8087f832
0xffffff80b69d3cb0 : 0xffffff7f8087f93d
0xffffff80b69d3cd0 : 0xffffff7f8088b625
0xffffff80b69d3d40 : 0xffffff7f80889c76
0xffffff80b69d3d80 : 0xffffff80006245ca
0xffffff80b69d3dd0 : 0xffffff8000657d4e
0xffffff80b69d3e30 : 0xffffff80002a3851
0xffffff80b69d3e80 : 0xffffff8000223096
0xffffff80b69d3eb0 : 0xffffff80002148a9
0xffffff80b69d3f10 : 0xffffff800021bbd8
0xffffff80b69d3f70 : 0xffffff80002aef10
0xffffff80b69d3fb0 : 0xffffff80002daec3
      Kernel Extensions in backtrace:
         com.apple.iokit.IOGraphicsFamily(2.3.4)[D0A1F6BD-E66E-3DD8-9913-A3AB8746F422]@0 xffffff7f80874000->0xffffff7f808acfff
            dependency: com.apple.iokit.IOPCIFamily(2.7)[5C23D598-58B2-3204-BC03-BC3C0F00BD32]@0xffffff 7f80849000
         com.apple.GeForce(7.3.2)[7E1D7726-416F-3716-ACCB-E1E276E35002]@0xffffff7f81d590 00->0xffffff7f81e1bfff
            dependency: com.apple.NVDAResman(7.3.2)[97284661-2629-379E-B86B-D388618E8C30]@0xffffff7f808 bf000
            dependency: com.apple.iokit.IONDRVSupport(2.3.4)[7C8672C4-8B0D-3CCF-A79A-23C62E90F895]@0xff ffff7f808ad000
            dependency: com.apple.iokit.IOPCIFamily(2.7)[5C23D598-58B2-3204-BC03-BC3C0F00BD32]@0xffffff 7f80849000
            dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[D0A1F6BD-E66E-3DD8-9913-A3AB8746F422]@0 xffffff7f80874000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
11G63
Kernel version:
Darwin Kernel Version 11.4.2: Thu Aug 23 16:25:48 PDT 2012; root:xnu-1699.32.7~1/RELEASE_X86_64
Kernel UUID: FF3BB088-60A4-349C-92EA-CA649C698CE5
System model name: MacBookPro4,1 (Mac-F42C89C8)
System uptime in nanoseconds: 62230646656
last loaded kext at 53384504695: com.apple.filesystems.autofs 3.0 (addr 0xffffff7f81efc000, size 45056)
loaded kexts:
com.apple.filesystems.autofs 3.0
com.apple.driver.AudioAUUC 1.59
com.apple.driver.AppleTyMCEDriver 1.0.2d2
com.apple.driver.AppleUpstreamUserClient 3.5.9
com.apple.driver.AppleHDAHardwareConfigDriver 2.2.5a5
com.apple.driver.AppleHDA 2.2.5a5
com.apple.GeForce 7.3.2
com.apple.driver.SMCMotionSensor 3.0.2d6
com.apple.driver.AppleSMCPDRC 5.0.0d8
com.apple.driver.AppleSMCLMU 2.0.1d2
com.apple.driver.AppleMuxControl 3.1.33
com.apple.driver.AppleBacklight 170.2.2
com.apple.driver.AppleMCCSControl 1.0.33
com.apple.iokit.IOUserEthernet 1.0.0d1
com.apple.iokit.IOBluetoothSerialManager 4.0.8f17
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.AudioIPCDriver 1.2.3
com.apple.driver.ApplePolicyControl 3.1.33
com.apple.driver.ACPI_SMC_PlatformPlugin 5.0.0d8
com.apple.driver.AppleLPC 1.6.0
com.apple.driver.AppleUSBTCButtons 227.6
com.apple.driver.BroadcomUSBBluetoothHCIController 4.0.8f17
com.apple.driver.AppleUSBTCKeyEventDriver 227.6
com.apple.driver.AppleUSBTCKeyboard 227.6
com.apple.driver.AppleIRController 312
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 33
com.apple.iokit.SCSITaskUserClient 3.2.1
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.1.0
com.apple.iokit.AppleYukon2 3.2.2b1
com.apple.driver.AppleUSBHub 5.1.0
com.apple.driver.AppleAHCIPort 2.3.1
com.apple.driver.AppleEFINVRAM 1.6.1
com.apple.driver.AirPortBrcm43224 501.36.15
com.apple.driver.AppleFWOHCI 4.9.0
com.apple.driver.AppleIntelPIIXATA 2.5.1
com.apple.driver.AppleUSBEHCI 5.1.0
com.apple.driver.AppleRTC 1.5
com.apple.driver.AppleUSBUHCI 5.1.0
com.apple.driver.AppleHPET 1.7
com.apple.driver.AppleSmartBatteryManager 161.0.0
com.apple.driver.AppleACPIButtons 1.5
com.apple.driver.AppleSMBIOS 1.9
com.apple.driver.AppleACPIEC 1.5
com.apple.driver.AppleAPIC 1.6
com.apple.driver.AppleIntelCPUPowerManagementClient 195.0.0
com.apple.nke.applicationfirewall 3.2.30
com.apple.security.quarantine 1.4
com.apple.security.TMSafetyNet 8
com.apple.driver.AppleIntelCPUPowerManagement 195.0.0
com.apple.kext.triggers 1.0
com.apple.driver.DspFuncLib 2.2.5a5
com.apple.nvidia.nv50hal 7.3.2
com.apple.nvidia.nvGK100hal 7.3.2
com.apple.nvidia.nvGF100hal 7.3.2
com.apple.NVDAResman 7.3.2
com.apple.iokit.IOFireWireIP 2.2.5
com.apple.driver.AppleBacklightExpert 1.0.4
com.apple.driver.AppleSMBusController 1.0.10d0
com.apple.driver.AppleHDAController 2.2.5a5
com.apple.iokit.IOHDAFamily 2.2.5a5
com.apple.iokit.IOSurface 80.0.2
com.apple.iokit.IOSerialFamily 10.0.5
com.apple.iokit.IOAudioFamily 1.8.6fc18
com.apple.kext.OSvKernDSPLib 1.3
com.apple.driver.AppleGraphicsControl 3.1.33
com.apple.iokit.IONDRVSupport 2.3.4
com.apple.iokit.IOGraphicsFamily 2.3.4
com.apple.driver.AppleSMC 3.1.3d10
com.apple.driver.IOPlatformPluginLegacy 5.0.0d8
com.apple.driver.AppleSMBusPCI 1.0.10d0
com.apple.driver.IOPlatformPluginFamily 5.1.1d6
com.apple.driver.AppleFileSystemDriver 13
com.apple.driver.AppleUSBBluetoothHCIController 4.0.8f17
com.apple.iokit.IOBluetoothFamily 4.0.8f17
com.apple.driver.AppleUSBMultitouch 230.5
com.apple.iokit.IOUSBHIDDriver 5.0.0
com.apple.driver.AppleUSBMergeNub 5.1.0
com.apple.driver.AppleUSBComposite 5.0.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.2.1
com.apple.iokit.IOBDStorageFamily 1.7
com.apple.iokit.IODVDStorageFamily 1.7.1
com.apple.iokit.IOCDStorageFamily 1.7.1
com.apple.iokit.IOATAPIProtocolTransport 3.0.0
com.apple.iokit.IOSCSIArchitectureModelFamily 3.2.1
com.apple.iokit.IOUSBUserClient 5.0.0
com.apple.iokit.IOAHCIFamily 2.0.8
com.apple.iokit.IO80211Family 420.3
com.apple.iokit.IONetworkingFamily 2.1
com.apple.iokit.IOFireWireFamily 4.4.8
com.apple.iokit.IOATAFamily 2.5.1
com.apple.driver.AppleEFIRuntime 1.6.1
com.apple.iokit.IOUSBFamily 5.1.0
com.apple.iokit.IOHIDFamily 1.7.1
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 177.11
com.apple.kext.AppleMatch 1.0.0d1
com.apple.driver.DiskImages 331.7
com.apple.iokit.IOStorageFamily 1.7.2
com.apple.driver.AppleKeyStore 28.18
com.apple.driver.AppleACPIPlatform 1.5
com.apple.iokit.IOPCIFamily 2.7
com.apple.iokit.IOACPIFamily 1.4
Model: MacBookPro4,1, BootROM MBP41.00C1.B00, 2 processors, Intel Core 2 Duo, 2.4 GHz, 6 GB, SMC 1.27f3
Graphics: NVIDIA GeForce 8600M GT, GeForce 8600M GT, PCIe, 256 MB
Memory Module: BANK 0/DIMM0, 4 GB, DDR2 SDRAM, 667 MHz, 0x7F7F7F7F7F9B0000, 0x4354353132363441433636372E4D31364643
Memory Module: BANK 1/DIMM1, 2 GB, DDR2 SDRAM, 667 MHz, 0x7F7FBAFFFFFFFFFF, 0xFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8C), Broadcom BCM43xx 1.0 (5.10.131.36.15)
Bluetooth: Version 4.0.8f17, 2 service, 18 devices, 1 incoming serial ports
Network Service: Wi-Fi, AirPort, en1
Serial ATA Device: Hitachi HTS543225L9SA02, 250.06 GB
Parallel ATA Device: MATSHITADVD-R   UJ-867
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x1a100000 / 2
USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x820f, 0x1a110000 / 5
USB Device: Built-in iSight, apple_vendor_id, 0x8502, 0xfd400000 / 2
USB Device: Apple Internal Keyboard / Trackpad, apple_vendor_id, 0x0230, 0x5d200000 / 3
USB Device: IR Receiver, apple_vendor_id, 0x8242, 0x5d100000 / 2

I had already written a book and I did not want to bombard people with more information, but in my previous research I did come across the major issues with the NVIDIA card. I also was well aware that Apple offered a replacement program that ended in December of 2012. I was going to add that in my original post, but I discounted that theory because I put my faith in the so called "Apple Genius" when I made my second trip to the Apple Store. I brought the NVIDIA card issue to his attention and asked him if he thought that may be the problem, but he said no. He said if it was the NVIDIA card that the screen would be completely black and there would be no startup chime. When I experienced the screen issues I thought it was a problem with the NVIDIA card or the logic board. I asked myself, how can a flawed hard drive cause the screen to act funny.
nbar and Rick Warren, I thank you both for your help and insight; people like you are the real "Apple Geniuses." I was hoping there was a way I could wipe the hard drive before I dumped the computer or attempted to sell it. I guess I will look into purchasing a new machine when I have the funds. Again...thank you both!

Firefox 16.0 and the last 15.0.1 I had issues with yahoo mail page turning fuzzy and an error message firefox is unresponsive. Page froze up and could not close

I signed into yahoo mail okay. what happens is after I open my mail the past two days all of a sudden the page would get fuzzy and I couldn't read anything or it would turn white. This never happened before and I looked at the top of the browser and it said mozilla firefox is unresponsive. I tried signing out and nothing worked. I tried minimizing the page and closing it manually and it would not let me. I tried deleting cookies and what happened it that the temporary files kept deleting for about five minutes. it was very upsetting. I have no idea what is causing this. Even when I went to control panel-internet options-delete cookies it sometimes went unresponsive. that's a first. any advise is helpful

Firefox keeps its own temporary files and cookies, separate from the ones stored by IE which you can manage through the Windows menu. If you haven't already done the following, please give it a try:
(1) Bypass Firefox's Cache
Use Ctrl+Shift+r to reload the page fresh from the server.
(You also can clear Firefox's cache completely using:
orange Firefox button ''or'' Tools menu > Options > Advanced
On the Network mini-tab > Cached Web Content : "Clear Now")
(2) Remove your yahoo.com cookies (save any pending work first) using either of these:
* While viewing a page on the site, right-click and choose View Page Info > Security > "View Cookies"
* Alt+t (open the classic Tools menu) > Page Info > Security > "View Cookies"
Then try reloading the page. Does that help at all?
When Yahoo goes blank or fuzzy moving to a different task, it may be doing some kind of animated transition. Have you noticed any graphics or font rendering anomalies?
Try disabling Firefox's hardware acceleration of graphics. Since this feature was added to Firefox, it has gradually improved, but there still are a few glitches.
You usually need to restart Firefox in order for this to take effect, so save all work first (e.g., mail you are composing, online documents you're editing, etc.).
orange Firefox button ''or'' classic Tools menu > Options > Advanced
On the "General" mini-tab, uncheck the box for "Use hardware acceleration when available"
If you restart Firefox, is the issue improved?

Delete all instances of a button in a project - Captivate 4

Hi there.
It seems that with Captivate 2 (or maybe 3), you could copy a button and paste it on all the rest of the slides in your project. Then if you had to modify that button, you could select it from the Library (memory's fuzzy here, that may not be accurate), then delete it, and it would delete the button from every slide.
With Captivate 4, I don't see any buttons in the Library. It also appears that if I paste a button onto all of my slides, each button is renamed and lives as a separate instance, and it's not just replicas of the original button.
Is this the case?
Basically, I want to delete a button from my project that's been pasted on all of my slides. Without deleting it slide by slide. Can this be done in Captivate 4?
I am aware of persistent buttons available via the Widgets functionality, but that wasn't appropriate for my project in this case.
Thanks,
Tichelle

Here's a way to at least delete all Back buttons in a project at once:
1.    Select Preferences from Edit menu.
2.    In the Category pane on the left side of the Preferences window, select Quiz>Settings.
3.    Under the Settings part of the window, uncheck the box next to “Allow backward movement.”
4.    Click the OK button.
NOTES: • Depending on how many slides are in your project, it can take several seconds to complete the process. The Preferences window will disappear when it has completed removing all Back buttons.
                 • Also, if this doesn’t work for some reason (it didn’t remove the Back buttons from all my slides a couple of times), start by first selecting all slides (from Edit menu or Ctrl+A).

Screen display looks fuzzy using xf86-video-intel on a HP Pavilion 23

Hello,
First off I want to say, thank you for Arch! Been using some distros on and off and I think I found my /home! I made a full plunge into Linux a bit ago after some Windows 8.1 issues, switched to Arch and not looking back. Anyways, So far all my computers are either Arch or Manjaro which I am moving more towards straight arch as Manjaro does have some issues when updating your system (dependency loops). All and all not bad, just liking the full control of a pure system then building from scratch.
Ok, the issue at hand. I have removed Windows 8.1 from my HP All in One Pavilion 23 machine....what a nightmare that was.... Everything was good after turning off secure boot. I installed Arch Linux (3.14.4-1) x86_64, and I am having issues getting the xf86-video-intel driver to play nice with X.
I have taken a screenshot:
Screenshot
I notice this starts right after the choosing the Arch Linux from the boot option menu. It starts the load nice and crisp but after a second the screen flickers with some lines at the top of the screen, random colors, only about the top 3rd of the screen. This modules begin to load but the terminal text looks blocky and horrible.
I am using Openbox 3.5.2-6 with slim 1.3.6-4. Running xorg-server 1.15.1-1 and xorg-server-utils 7.6-3 with all the dependencies of course.
Output from pacman queries for video drivers
xf86-video-intel 2.99.911-2
xf86-video-vesa 2.3.2-4
lspci output
00:00.0 Host bridge: Intel Corporation 4th Gen Core Processor DRAM Controller (rev 06)
00:02.0 VGA compatible controller: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor Integrated Graphics Controller (rev 06)
00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05)
00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 05)
00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 05)
00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 (rev d5)
00:1c.2 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #3 (rev d5)
00:1c.4 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #5 (rev d5)
00:1c.5 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #6 (rev d5)
00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 (rev 05)
00:1f.0 ISA bridge: Intel Corporation H87 Express LPC Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05)
00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 05)
02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 0c)
03:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5229 PCI Express Card Reader (rev 01)
04:00.0 Network controller: Qualcomm Atheros AR9485 Wireless Network Adapter (rev 01)
my /etc/mkinitcpio.conf
# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run. Advanced users may wish to specify all system modules
# in this array. For instance:
# MODULES="piix ide_disk reiserfs"
MODULES="i915"
# BINARIES
# This setting includes any additional binaries a given user may
# wish into the CPIO image. This is run last, so it may be used to
# override the actual binaries included by a given hook
# BINARIES are dependency parsed, so you may safely ignore libraries
BINARIES=""
# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in any way. This is useful for config files.
FILES=""
# HOOKS
# This is the most important setting in this file. The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added. Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
## This setup specifies all modules in the MODULES setting above.
## No raid, lvm2, or encrypted root is needed.
# HOOKS="base"
## This setup will autodetect all modules for your system and should
## work as a sane default
# HOOKS="base udev autodetect block filesystems"
## This setup will generate a 'full' image which supports most systems.
## No autodetection is done.
# HOOKS="base udev block filesystems"
## This setup assembles a pata mdadm array with an encrypted root FS.
## Note: See 'mkinitcpio -H mdadm' for more information on raid devices.
# HOOKS="base udev block mdadm encrypt filesystems"
## This setup loads an lvm2 volume group on a usb device.
# HOOKS="base udev block lvm2 filesystems"
## NOTE: If you have /usr on a separate partition, you MUST include the
# usr, fsck and shutdown hooks.
HOOKS="base udev autodetect modconf block filesystems keyboard fsck"
# COMPRESSION
# Use this to compress the initramfs image. By default, gzip compression
# is used. Use 'cat' to create an uncompressed image.
#COMPRESSION="gzip"
#COMPRESSION="bzip2"
#COMPRESSION="lzma"
#COMPRESSION="xz"
#COMPRESSION="lzop"
#COMPRESSION="lz4"
# COMPRESSION_OPTIONS
# Additional options for the compressor
#COMPRESSION_OPTIONS=""
,my /etc/default/grub.conf
GRUB_DEFAULT=0
GRUB_TIMEOUT=5
GRUB_DISTRIBUTOR="Arch"
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash"
GRUB_CMDLINE_LINUX=""
# Preload both GPT and MBR modules so that they are not missed
GRUB_PRELOAD_MODULES="part_gpt part_msdos"
# Uncomment to enable Hidden Menu, and optionally hide the timeout count
#GRUB_HIDDEN_TIMEOUT=5
#GRUB_HIDDEN_TIMEOUT_QUIET=true
# Uncomment to use basic console
GRUB_TERMINAL_INPUT=console
# Uncomment to disable graphical terminal
#GRUB_TERMINAL_OUTPUT=console
# The resolution used on graphical terminal
# note that you can use only modes which your graphic card supports via VBE
# you can see them in real GRUB with the command `vbeinfo'
GRUB_GFXMODE=auto
# Uncomment to allow the kernel use the same resolution used by grub
GRUB_GFXPAYLOAD_LINUX=keep
# Uncomment if you want GRUB to pass to the Linux kernel the old parameter
# format "root=/dev/xxx" instead of "root=/dev/disk/by-uuid/xxx"
#GRUB_DISABLE_LINUX_UUID=true
# Uncomment to disable generation of recovery mode menu entries
GRUB_DISABLE_RECOVERY=true
# Uncomment and set to the desired menu colors. Used by normal and wallpaper
# modes only. Entries specified as foreground/background.
#GRUB_COLOR_NORMAL="light-blue/black"
#GRUB_COLOR_HIGHLIGHT="light-cyan/blue"
# Uncomment one of them for the gfx desired, a image background or a gfxtheme
#GRUB_BACKGROUND="/path/to/wallpaper"
#GRUB_THEME="/path/to/gfxtheme"
# Uncomment to get a beep at GRUB start
#GRUB_INIT_TUNE="480 440 1"
#GRUB_SAVEDEFAULT="true"
And last my /var/log/Xorg.0.log
[ 15.641]
X.Org X Server 1.15.1
Release Date: 2014-04-13
[ 15.641] X Protocol Version 11, Revision 0
[ 15.641] Build Operating System: Linux 3.14.0-4-ARCH x86_64
[ 15.641] Current Operating System: Linux localhost 3.14.4-1-ARCH #1 SMP PREEMPT Tue May 13 16:41:39 CEST 2014 x86_64
[ 15.641] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=0c1916a0-b631-478f-ac6b-aa5d123f75cd rw quiet splash
[ 15.641] Build Date: 14 April 2014 08:39:09AM
[ 15.641]
[ 15.641] Current version of pixman: 0.32.4
[ 15.641] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 15.641] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 15.641] (==) Log file: "/var/log/Xorg.0.log", Time: Sun Jun 1 17:05:15 2014
[ 15.687] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 15.687] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 15.739] (==) No Layout section. Using the first Screen section.
[ 15.739] (==) No screen section available. Using defaults.
[ 15.739] (**) |-->Screen "Default Screen Section" (0)
[ 15.739] (**) | |-->Monitor "<default monitor>"
[ 15.764] (==) No device specified for screen "Default Screen Section".
Using the first device section listed.
[ 15.764] (**) | |-->Device "Intel Graphics"
[ 15.764] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 15.764] (==) Automatically adding devices
[ 15.764] (==) Automatically enabling devices
[ 15.764] (==) Automatically adding GPU devices
[ 15.793] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 15.793] Entry deleted from font path.
[ 15.795] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/OTF/,
/usr/share/fonts/100dpi/,
/usr/share/fonts/75dpi/
[ 15.795] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 15.795] (**) Extension "Composite" is enabled
[ 15.795] (**) Extension "RENDER" is enabled
[ 15.795] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 15.795] (II) Loader magic: 0x804c80
[ 15.795] (II) Module ABI versions:
[ 15.795] X.Org ANSI C Emulation: 0.4
[ 15.795] X.Org Video Driver: 15.0
[ 15.795] X.Org XInput driver : 20.0
[ 15.796] X.Org Server Extension : 8.0
[ 15.796] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 15.798] (--) PCI:*(0:0:2:0) 8086:0412:103c:2b0f rev 6, Mem @ 0xf7800000/4194304, 0xe0000000/268435456, I/O @ 0x0000f000/64
[ 15.798] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 15.798] Initializing built-in extension Generic Event Extension
[ 15.798] Initializing built-in extension SHAPE
[ 15.798] Initializing built-in extension MIT-SHM
[ 15.798] Initializing built-in extension XInputExtension
[ 15.798] Initializing built-in extension XTEST
[ 15.798] Initializing built-in extension BIG-REQUESTS
[ 15.798] Initializing built-in extension SYNC
[ 15.798] Initializing built-in extension XKEYBOARD
[ 15.798] Initializing built-in extension XC-MISC
[ 15.798] Initializing built-in extension SECURITY
[ 15.798] Initializing built-in extension XINERAMA
[ 15.798] Initializing built-in extension XFIXES
[ 15.798] Initializing built-in extension RENDER
[ 15.799] Initializing built-in extension RANDR
[ 15.799] Initializing built-in extension COMPOSITE
[ 15.799] Initializing built-in extension DAMAGE
[ 15.799] Initializing built-in extension MIT-SCREEN-SAVER
[ 15.799] Initializing built-in extension DOUBLE-BUFFER
[ 15.799] Initializing built-in extension RECORD
[ 15.799] Initializing built-in extension DPMS
[ 15.799] Initializing built-in extension Present
[ 15.799] Initializing built-in extension DRI3
[ 15.799] Initializing built-in extension X-Resource
[ 15.799] Initializing built-in extension XVideo
[ 15.799] Initializing built-in extension XVideo-MotionCompensation
[ 15.799] Initializing built-in extension XFree86-VidModeExtension
[ 15.799] Initializing built-in extension XFree86-DGA
[ 15.799] Initializing built-in extension XFree86-DRI
[ 15.799] Initializing built-in extension DRI2
[ 15.799] (II) "glx" will be loaded by default.
[ 15.799] (II) LoadModule: "dri2"
[ 15.799] (II) Module "dri2" already built-in
[ 15.799] (II) LoadModule: "glamoregl"
[ 15.808] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[ 15.917] (II) Module glamoregl: vendor="X.Org Foundation"
[ 15.917] compiled for 1.15.0, module version = 0.6.0
[ 15.917] ABI class: X.Org ANSI C Emulation, version 0.4
[ 15.917] (II) LoadModule: "glx"
[ 15.917] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 15.928] (II) Module glx: vendor="X.Org Foundation"
[ 15.929] compiled for 1.15.1, module version = 1.0.0
[ 15.929] ABI class: X.Org Server Extension, version 8.0
[ 15.929] (==) AIGLX enabled
[ 15.929] Loading extension GLX
[ 15.929] (II) LoadModule: "intel"
[ 15.929] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 15.955] (II) Module intel: vendor="X.Org Foundation"
[ 15.955] compiled for 1.15.0, module version = 2.99.911
[ 15.955] Module class: X.Org Video Driver
[ 15.955] ABI class: X.Org Video Driver, version 15.0
[ 15.955] (II) intel: Driver for Intel(R) Integrated Graphics Chipsets:
i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G,
915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM,
Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33,
GM45, 4 Series, G45/G43, Q45/Q43, G41, B43
[ 15.956] (II) intel: Driver for Intel(R) HD Graphics: 2000-5000
[ 15.956] (II) intel: Driver for Intel(R) Iris(TM) Graphics: 5100
[ 15.956] (II) intel: Driver for Intel(R) Iris(TM) Pro Graphics: 5200
[ 15.956] (++) using VT number 7
[ 15.971] (--) intel(0): Integrated Graphics Chipset: Intel(R) HD Graphics 4600
[ 15.971] (--) intel(0): CPU: x86-64, sse2, sse3, ssse3, sse4.1, sse4.2, avx, avx2
[ 15.971] (II) intel(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 15.971] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[ 15.971] (==) intel(0): RGB weight 888
[ 15.971] (==) intel(0): Default visual is TrueColor
[ 15.971] (**) intel(0): Option "AccelMethod" "sna"
[ 15.971] (**) intel(0): Option "DRI" "true"
[ 15.971] (**) intel(0): Option "TearFree" "true"
[ 15.972] (**) intel(0): Framebuffer tiled
[ 15.972] (**) intel(0): Pixmaps tiled
[ 15.972] (**) intel(0): "Tear free" enabled
[ 15.972] (**) intel(0): Forcing per-crtc-pixmaps? no
[ 15.972] (II) intel(0): Output eDP1 has no monitor section
[ 15.972] (--) intel(0): Found backlight control interface acpi_video0 (type 'firmware') for output eDP1
[ 15.972] (II) intel(0): Output VGA1 has no monitor section
[ 15.972] (II) intel(0): Output DP1 has no monitor section
[ 15.972] (II) intel(0): Output HDMI1 has no monitor section
[ 15.972] (II) intel(0): Output DP2 has no monitor section
[ 15.972] (II) intel(0): Output HDMI2 has no monitor section
[ 15.972] (II) intel(0): Output VIRTUAL1 has no monitor section
[ 15.972] (--) intel(0): Output eDP1 using initial mode 1920x1080 on pipe 0
[ 15.972] (==) intel(0): DPI set to (96, 96)
[ 15.972] (II) Loading sub module "dri2"
[ 15.972] (II) LoadModule: "dri2"
[ 15.972] (II) Module "dri2" already built-in
[ 15.972] (==) Depth 24 pixmap format is 32 bpp
[ 15.986] (II) intel(0): SNA initialized with Haswell (gen7.5, gt2) backend
[ 15.986] (==) intel(0): Backing store enabled
[ 15.986] (==) intel(0): Silken mouse enabled
[ 15.986] (II) intel(0): HW Cursor enabled
[ 15.986] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 15.987] (==) intel(0): DPMS enabled
[ 15.987] (II) intel(0): [DRI2] Setup complete
[ 15.987] (II) intel(0): [DRI2] DRI driver: i965
[ 15.987] (II) intel(0): [DRI2] VDPAU driver: i965
[ 15.987] (II) intel(0): direct rendering: DRI2 Enabled
[ 15.987] (==) intel(0): hotplug detection: "enabled"
[ 15.987] (--) RandR disabled
[ 16.067] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 16.067] (II) AIGLX: enabled GLX_ARB_create_context
[ 16.067] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 16.067] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[ 16.067] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 16.067] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 16.067] (II) AIGLX: enabled GLX_EXT_framebuffer_sRGB
[ 16.067] (II) AIGLX: enabled GLX_ARB_fbconfig_float
[ 16.067] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 16.067] (II) AIGLX: enabled GLX_ARB_create_context_robustness
[ 16.067] (II) AIGLX: Loaded and initialized i965
[ 16.067] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 16.085] (II) intel(0): switch to mode [email protected] on eDP1 using pipe 0, position (0, 0), rotation normal, reflection none
[ 16.107] (II) intel(0): Setting screen physical size to 508 x 285
[ 16.375] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 16.375] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 16.375] (II) LoadModule: "evdev"
[ 16.383] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 16.402] (II) Module evdev: vendor="X.Org Foundation"
[ 16.402] compiled for 1.15.1, module version = 2.9.0
[ 16.402] Module class: X.Org XInput Driver
[ 16.402] ABI class: X.Org XInput driver, version 20.0
[ 16.402] (II) Using input driver 'evdev' for 'Power Button'
[ 16.402] (**) Power Button: always reports core events
[ 16.402] (**) evdev: Power Button: Device: "/dev/input/event1"
[ 16.402] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 16.402] (--) evdev: Power Button: Found keys
[ 16.402] (II) evdev: Power Button: Configuring as keyboard
[ 16.402] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1/event1"
[ 16.402] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 16.402] (**) Option "xkb_rules" "evdev"
[ 16.402] (**) Option "xkb_model" "pc104"
[ 16.402] (**) Option "xkb_layout" "us"
[ 16.442] (II) config/udev: Adding input device Video Bus (/dev/input/event2)
[ 16.442] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 16.442] (II) Using input driver 'evdev' for 'Video Bus'
[ 16.442] (**) Video Bus: always reports core events
[ 16.442] (**) evdev: Video Bus: Device: "/dev/input/event2"
[ 16.442] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 16.442] (--) evdev: Video Bus: Found keys
[ 16.442] (II) evdev: Video Bus: Configuring as keyboard
[ 16.442] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:01/input/input2/event2"
[ 16.442] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 16.442] (**) Option "xkb_rules" "evdev"
[ 16.442] (**) Option "xkb_model" "pc104"
[ 16.442] (**) Option "xkb_layout" "us"
[ 16.443] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[ 16.443] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 16.443] (II) Using input driver 'evdev' for 'Power Button'
[ 16.443] (**) Power Button: always reports core events
[ 16.443] (**) evdev: Power Button: Device: "/dev/input/event0"
[ 16.443] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 16.443] (--) evdev: Power Button: Found keys
[ 16.443] (II) evdev: Power Button: Configuring as keyboard
[ 16.443] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0/event0"
[ 16.443] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[ 16.443] (**) Option "xkb_rules" "evdev"
[ 16.443] (**) Option "xkb_model" "pc104"
[ 16.443] (**) Option "xkb_layout" "us"
[ 16.444] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 16.444] (II) config/udev: Adding input device HP High Definition 1MP Webcam (/dev/input/event8)
[ 16.444] (**) HP High Definition 1MP Webcam: Applying InputClass "evdev keyboard catchall"
[ 16.444] (II) Using input driver 'evdev' for 'HP High Definition 1MP Webcam'
[ 16.444] (**) HP High Definition 1MP Webcam: always reports core events
[ 16.444] (**) evdev: HP High Definition 1MP Webcam: Device: "/dev/input/event8"
[ 16.444] (--) evdev: HP High Definition 1MP Webcam: Vendor 0x4f2 Product 0xb40b
[ 16.444] (--) evdev: HP High Definition 1MP Webcam: Found keys
[ 16.444] (II) evdev: HP High Definition 1MP Webcam: Configuring as keyboard
[ 16.444] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-5/1-5:1.0/input/input8/event8"
[ 16.444] (II) XINPUT: Adding extended input device "HP High Definition 1MP Webcam" (type: KEYBOARD, id 9)
[ 16.444] (**) Option "xkb_rules" "evdev"
[ 16.444] (**) Option "xkb_model" "pc104"
[ 16.445] (**) Option "xkb_layout" "us"
[ 16.445] (II) config/udev: Adding input device NextWindow Touchscreen (/dev/input/event14)
[ 16.445] (**) NextWindow Touchscreen: Applying InputClass "evdev touchscreen catchall"
[ 16.445] (II) Using input driver 'evdev' for 'NextWindow Touchscreen'
[ 16.445] (**) NextWindow Touchscreen: always reports core events
[ 16.445] (**) evdev: NextWindow Touchscreen: Device: "/dev/input/event14"
[ 16.445] (--) evdev: NextWindow Touchscreen: Vendor 0x1926 Product 0x33e
[ 16.445] (--) evdev: NextWindow Touchscreen: Found absolute axes
[ 16.445] (--) evdev: NextWindow Touchscreen: Found absolute multitouch axes
[ 16.445] (II) evdev: NextWindow Touchscreen: No buttons found, faking one.
[ 16.445] (--) evdev: NextWindow Touchscreen: Found x and y absolute axes
[ 16.445] (--) evdev: NextWindow Touchscreen: Found absolute touchscreen
[ 16.445] (II) evdev: NextWindow Touchscreen: Configuring as touchscreen
[ 16.445] (**) evdev: NextWindow Touchscreen: YAxisMapping: buttons 4 and 5
[ 16.445] (**) evdev: NextWindow Touchscreen: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 16.446] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-7/1-7:1.0/0003:1926:033E.0001/input/input14/event14"
[ 16.446] (II) XINPUT: Adding extended input device "NextWindow Touchscreen" (type: TOUCHSCREEN, id 10)
[ 16.446] (II) evdev: NextWindow Touchscreen: initialized for absolute axes.
[ 16.446] (**) NextWindow Touchscreen: (accel) keeping acceleration scheme 1
[ 16.446] (**) NextWindow Touchscreen: (accel) acceleration profile 0
[ 16.446] (**) NextWindow Touchscreen: (accel) acceleration factor: 2.000
[ 16.446] (**) NextWindow Touchscreen: (accel) acceleration threshold: 4
[ 16.446] (II) config/udev: Adding input device NextWindow Touchscreen (/dev/input/mouse2)
[ 16.446] (II) No input driver specified, ignoring this device.
[ 16.446] (II) This device may have been added with another device file.
[ 16.447] (II) config/udev: Adding input device NextWindow Touchscreen (/dev/input/event9)
[ 16.447] (II) No input driver specified, ignoring this device.
[ 16.447] (II) This device may have been added with another device file.
[ 16.447] (II) config/udev: Adding input device NextWindow Touchscreen (/dev/input/event10)
[ 16.447] (**) NextWindow Touchscreen: Applying InputClass "evdev pointer catchall"
[ 16.447] (II) Using input driver 'evdev' for 'NextWindow Touchscreen'
[ 16.447] (**) NextWindow Touchscreen: always reports core events
[ 16.447] (**) evdev: NextWindow Touchscreen: Device: "/dev/input/event10"
[ 16.447] (--) evdev: NextWindow Touchscreen: Vendor 0x1926 Product 0x33e
[ 16.447] (--) evdev: NextWindow Touchscreen: Found 3 mouse buttons
[ 16.447] (--) evdev: NextWindow Touchscreen: Found absolute axes
[ 16.447] (--) evdev: NextWindow Touchscreen: Found x and y absolute axes
[ 16.447] (--) evdev: NextWindow Touchscreen: Found absolute touchscreen
[ 16.447] (II) evdev: NextWindow Touchscreen: Configuring as touchscreen
[ 16.447] (**) evdev: NextWindow Touchscreen: YAxisMapping: buttons 4 and 5
[ 16.447] (**) evdev: NextWindow Touchscreen: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 16.448] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-7/1-7:1.2/0003:1926:033E.0003/input/input10/event10"
[ 16.448] (II) XINPUT: Adding extended input device "NextWindow Touchscreen" (type: TOUCHSCREEN, id 11)
[ 16.448] (II) evdev: NextWindow Touchscreen: initialized for absolute axes.
[ 16.448] (**) NextWindow Touchscreen: (accel) keeping acceleration scheme 1
[ 16.448] (**) NextWindow Touchscreen: (accel) acceleration profile 0
[ 16.448] (**) NextWindow Touchscreen: (accel) acceleration factor: 2.000
[ 16.448] (**) NextWindow Touchscreen: (accel) acceleration threshold: 4
[ 16.448] (II) config/udev: Adding input device NextWindow Touchscreen (/dev/input/js0)
[ 16.448] (II) No input driver specified, ignoring this device.
[ 16.448] (II) This device may have been added with another device file.
[ 16.449] (II) config/udev: Adding input device NextWindow Touchscreen (/dev/input/mouse0)
[ 16.449] (II) No input driver specified, ignoring this device.
[ 16.449] (II) This device may have been added with another device file.
[ 16.449] (II) config/udev: Adding input device Hewlett Packard HP Wireless Keyboard Kit (/dev/input/event11)
[ 16.449] (**) Hewlett Packard HP Wireless Keyboard Kit: Applying InputClass "evdev keyboard catchall"
[ 16.449] (II) Using input driver 'evdev' for 'Hewlett Packard HP Wireless Keyboard Kit'
[ 16.449] (**) Hewlett Packard HP Wireless Keyboard Kit: always reports core events
[ 16.449] (**) evdev: Hewlett Packard HP Wireless Keyboard Kit: Device: "/dev/input/event11"
[ 16.449] (--) evdev: Hewlett Packard HP Wireless Keyboard Kit: Vendor 0x461 Product 0x4e25
[ 16.449] (--) evdev: Hewlett Packard HP Wireless Keyboard Kit: Found keys
[ 16.449] (II) evdev: Hewlett Packard HP Wireless Keyboard Kit: Configuring as keyboard
[ 16.449] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-9/1-9:1.0/0003:0461:4E25.0004/input/input11/event11"
[ 16.449] (II) XINPUT: Adding extended input device "Hewlett Packard HP Wireless Keyboard Kit" (type: KEYBOARD, id 12)
[ 16.449] (**) Option "xkb_rules" "evdev"
[ 16.449] (**) Option "xkb_model" "pc104"
[ 16.449] (**) Option "xkb_layout" "us"
[ 16.450] (II) config/udev: Adding input device Hewlett Packard HP Wireless Keyboard Kit (/dev/input/event12)
[ 16.450] (**) Hewlett Packard HP Wireless Keyboard Kit: Applying InputClass "evdev keyboard catchall"
[ 16.450] (II) Using input driver 'evdev' for 'Hewlett Packard HP Wireless Keyboard Kit'
[ 16.450] (**) Hewlett Packard HP Wireless Keyboard Kit: always reports core events
[ 16.450] (**) evdev: Hewlett Packard HP Wireless Keyboard Kit: Device: "/dev/input/event12"
[ 16.450] (--) evdev: Hewlett Packard HP Wireless Keyboard Kit: Vendor 0x461 Product 0x4e25
[ 16.450] (--) evdev: Hewlett Packard HP Wireless Keyboard Kit: Found 1 mouse buttons
[ 16.450] (--) evdev: Hewlett Packard HP Wireless Keyboard Kit: Found scroll wheel(s)
[ 16.450] (--) evdev: Hewlett Packard HP Wireless Keyboard Kit: Found relative axes
[ 16.450] (II) evdev: Hewlett Packard HP Wireless Keyboard Kit: Forcing relative x/y axes to exist.
[ 16.450] (--) evdev: Hewlett Packard HP Wireless Keyboard Kit: Found absolute axes
[ 16.450] (II) evdev: Hewlett Packard HP Wireless Keyboard Kit: Forcing absolute x/y axes to exist.
[ 16.450] (--) evdev: Hewlett Packard HP Wireless Keyboard Kit: Found keys
[ 16.450] (II) evdev: Hewlett Packard HP Wireless Keyboard Kit: Configuring as mouse
[ 16.450] (II) evdev: Hewlett Packard HP Wireless Keyboard Kit: Configuring as keyboard
[ 16.450] (II) evdev: Hewlett Packard HP Wireless Keyboard Kit: Adding scrollwheel support
[ 16.450] (**) evdev: Hewlett Packard HP Wireless Keyboard Kit: YAxisMapping: buttons 4 and 5
[ 16.450] (**) evdev: Hewlett Packard HP Wireless Keyboard Kit: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 16.450] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-9/1-9:1.1/0003:0461:4E25.0005/input/input12/event12"
[ 16.450] (II) XINPUT: Adding extended input device "Hewlett Packard HP Wireless Keyboard Kit" (type: KEYBOARD, id 13)
[ 16.450] (**) Option "xkb_rules" "evdev"
[ 16.450] (**) Option "xkb_model" "pc104"
[ 16.450] (**) Option "xkb_layout" "us"
[ 16.451] (II) evdev: Hewlett Packard HP Wireless Keyboard Kit: initialized for relative axes.
[ 16.451] (WW) evdev: Hewlett Packard HP Wireless Keyboard Kit: ignoring absolute axes.
[ 16.451] (**) Hewlett Packard HP Wireless Keyboard Kit: (accel) keeping acceleration scheme 1
[ 16.451] (**) Hewlett Packard HP Wireless Keyboard Kit: (accel) acceleration profile 0
[ 16.451] (**) Hewlett Packard HP Wireless Keyboard Kit: (accel) acceleration factor: 2.000
[ 16.451] (**) Hewlett Packard HP Wireless Keyboard Kit: (accel) acceleration threshold: 4
[ 16.451] (II) config/udev: Adding input device Hewlett Packard HP Wireless Keyboard Kit (/dev/input/event13)
[ 16.451] (**) Hewlett Packard HP Wireless Keyboard Kit: Applying InputClass "evdev pointer catchall"
[ 16.451] (II) Using input driver 'evdev' for 'Hewlett Packard HP Wireless Keyboard Kit'
[ 16.451] (**) Hewlett Packard HP Wireless Keyboard Kit: always reports core events
[ 16.451] (**) evdev: Hewlett Packard HP Wireless Keyboard Kit: Device: "/dev/input/event13"
[ 16.452] (--) evdev: Hewlett Packard HP Wireless Keyboard Kit: Vendor 0x461 Product 0x4e25
[ 16.452] (--) evdev: Hewlett Packard HP Wireless Keyboard Kit: Found 3 mouse buttons
[ 16.452] (--) evdev: Hewlett Packard HP Wireless Keyboard Kit: Found scroll wheel(s)
[ 16.452] (--) evdev: Hewlett Packard HP Wireless Keyboard Kit: Found relative axes
[ 16.452] (--) evdev: Hewlett Packard HP Wireless Keyboard Kit: Found x and y relative axes
[ 16.452] (II) evdev: Hewlett Packard HP Wireless Keyboard Kit: Configuring as mouse
[ 16.452] (II) evdev: Hewlett Packard HP Wireless Keyboard Kit: Adding scrollwheel support
[ 16.452] (**) evdev: Hewlett Packard HP Wireless Keyboard Kit: YAxisMapping: buttons 4 and 5
[ 16.452] (**) evdev: Hewlett Packard HP Wireless Keyboard Kit: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 16.452] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-9/1-9:1.2/0003:0461:4E25.0006/input/input13/event13"
[ 16.452] (II) XINPUT: Adding extended input device "Hewlett Packard HP Wireless Keyboard Kit" (type: MOUSE, id 14)
[ 16.452] (II) evdev: Hewlett Packard HP Wireless Keyboard Kit: initialized for relative axes.
[ 16.452] (**) Hewlett Packard HP Wireless Keyboard Kit: (accel) keeping acceleration scheme 1
[ 16.452] (**) Hewlett Packard HP Wireless Keyboard Kit: (accel) acceleration profile 0
[ 16.452] (**) Hewlett Packard HP Wireless Keyboard Kit: (accel) acceleration factor: 2.000
[ 16.452] (**) Hewlett Packard HP Wireless Keyboard Kit: (accel) acceleration threshold: 4
[ 16.452] (II) config/udev: Adding input device Hewlett Packard HP Wireless Keyboard Kit (/dev/input/mouse1)
[ 16.452] (II) No input driver specified, ignoring this device.
[ 16.452] (II) This device may have been added with another device file.
[ 16.453] (II) config/udev: Adding input device HDA Intel PCH Mic (/dev/input/event6)
[ 16.453] (II) No input driver specified, ignoring this device.
[ 16.453] (II) This device may have been added with another device file.
[ 16.453] (II) config/udev: Adding input device HDA Intel PCH Line Out (/dev/input/event5)
[ 16.453] (II) No input driver specified, ignoring this device.
[ 16.453] (II) This device may have been added with another device file.
[ 16.453] (II) config/udev: Adding input device HDA Intel PCH Front Headphone (/dev/input/event4)
[ 16.453] (II) No input driver specified, ignoring this device.
[ 16.453] (II) This device may have been added with another device file.
[ 16.453] (II) config/udev: Adding input device PC Speaker (/dev/input/event3)
[ 16.453] (II) No input driver specified, ignoring this device.
[ 16.453] (II) This device may have been added with another device file.
[ 16.454] (II) config/udev: Adding input device HP WMI hotkeys (/dev/input/event7)
[ 16.454] (**) HP WMI hotkeys: Applying InputClass "evdev keyboard catchall"
[ 16.454] (II) Using input driver 'evdev' for 'HP WMI hotkeys'
[ 16.454] (**) HP WMI hotkeys: always reports core events
[ 16.454] (**) evdev: HP WMI hotkeys: Device: "/dev/input/event7"
[ 16.454] (--) evdev: HP WMI hotkeys: Vendor 0 Product 0
[ 16.454] (--) evdev: HP WMI hotkeys: Found keys
[ 16.454] (II) evdev: HP WMI hotkeys: Configuring as keyboard
[ 16.454] (**) Option "config_info" "udev:/sys/devices/virtual/input/input7/event7"
[ 16.454] (II) XINPUT: Adding extended input device "HP WMI hotkeys" (type: KEYBOARD, id 15)
[ 16.454] (**) Option "xkb_rules" "evdev"
[ 16.454] (**) Option "xkb_model" "pc104"
[ 16.454] (**) Option "xkb_layout" "us"
[ 1192.410] (II) intel(0): switch to mode [email protected] on eDP1 using pipe 0, position (0, 0), rotation normal, reflection none
[ 1811.202] (II) intel(0): switch to mode [email protected] on eDP1 using pipe 0, position (0, 0), rotation normal, reflection none
[ 5455.421] (II) intel(0): switch to mode [email protected] on eDP1 using pipe 0, position (0, 0), rotation normal, reflection none

I saw your post, and had found it incredulous that you have a 1920x1080 display. A bit of research and I found I was wrong.
So, it appears you are driving the panel at its native resolution. Unfortunately, trying to determine what you mean by "Fuzzy" is probably going to be like trying to nail Jello to a tree. But, let's give it a shot. Is it fuzzy before you start X? Are lines and shapes fuzzy? Or is it just text that is fuzzy?
If it is just fonts, it could be a problem with hinting. Hinting is where the edges of fonts are deliberately fuzzed and feathered to get the kerning correct when the physical pixels of the display don't quite line up. This works well, unless the thing doing the hinting does not understand the geometry of the display. In a color LCD, each pixel is actually made up of smaller sub pixels, generally three -- A red, a green, and a blue. Green is usually in the middle. Some displays have Two greens per pixel, arranged RGBG. Some displays even have yellow subpixels. Sometimes the subpixels are arranged left to right, sometimes they are arranged top to bottom. Long story short, if you have hinting enabled, but the geometry is configured incorrectly, bad things happen. Take a look at this wiki article

Why is the video quality so fuzzy?

I’ve got a Flip Ultra HD that we’re using to make simple business-related videos to upload to YouTube. If I'm able to upload directly from the Flip software without needing to edit the video, it looks great, crisp and clear. But we wanted to make something a little more complex that needed just a few edits. I got it all put together and then looked at my file/export options. I selected web streaming and it compressed it. I uploaded and viewed it and it looks like crap. So I exported again, using the CD-ROM setting, and it still looks fuzzy.
Am I doing something wrong? When I view the source files before importing them from the Flip camera into iMovie, they look great. Total size is about 320 meg. Then I'm cutting about a third of the video out from them which should reduce it further. But if I want to export with ‘full quality’ from iMovie, it’s going to create a 700 MB file. I can’t upload that to YT.
If I were to upload these directly (without the needed edits), it would look great and be much smaller than what iMovie wants to upload.
FYI, I'm doing this in iMovie 6 but just got iLife 09 to install. I’m wondering if I'll get any better results with iMovie 9.
Any help would be appreciated.
Message was edited by: Conejo

try this:
Export with QT/Expert settings.. hit the blue button..
next menu: choose 'Quicktime' again, click Options
choose 'Compression', choose h264 (=very efficient codec)
if your project is very 'huge', reduce the framerate to 15fps (=drops files size by half)
if your happy with YT 'standard res', reduce resolution to 320x240 ... (=reduces file size again by 3/4)
if you're a few bits over the limit: reduce audio sampling to 22kHz/mono
this should shrink your files to YT limits ..

HT204291 my airplay from my MacBook Pro to my tv through my apple tv is fuzzy- it just started being fuzzy about 2 months ago- it used to be clear- anyone else have this problem? How can I fix it?

my airplay from my MacBook Pro to my tv through my apple tv is fuzzy- it just started being fuzzy about 2 months ago- it used to be clear- anyone else have this problem? How can I fix it?

Hi freezebri,
The following steps may resolve your issue:
Apple TV: Basic troubleshooting
http://support.apple.com/kb/ht1551
If your TV screen appears fuzzy or black (you see no video)
Make sure the television you are using supports the Apple TV resolution requirements. Please see the Apple TV technical specifications.
When you connect power, check to make sure the LED turns on. If the LED is not on, then verify with a known good power outlet or connect something else to the outlet you're using for Apple TV and make sure it works (such as a lamp or clock).
Make sure you're using the correct video cables and that they are connected firmly to Apple TV and to your TV.
Connect the HDMI cable directly into the Apple TV and your television, remove any third party devices or adapters.
Make sure the input setting you've selected on your TV matches the input you have your video cables connected to. See the documentation that came with your TV for more information.
Change the Apple TV resolution by pressing and holding the Menu and Up button for six seconds. The Apple TV will automatically cycle to the next resolution at approximately 20 second intervals. Pressing the Selectbutton will immediately cycle to the next resolution.
If you are connected via HDMI, try unplugging and replugging your HDMI cable.
If HDMI isn't working on an Apple TV (1st generation), try component cables instead (and disconnect the HDMI cable temporarily). Read more about HDMI vs component video.
Hope this information helps ...
- Judy

Export a pdf to a swf file with navigation buttons???

I have CS4 and I've tried to export a couple indesign files using the swf export feature, but it the navigation of the file is very weak and not very intuitive, and when you zoom in to any of the text the text goes fuzzy.
I would like to just convert a PDF to SWF file with navigation buttons, page controls, zoom in/out, single or two page view options, so that my end user can view it with the free flash player, but I don't have time to build the file in Flash and I don't want to use an online service that comes with a per month or per publication fee.
Any suggestions??

I've looked at that, but most of the pdf's that I need to convert are more than 10 pages. I want a program I can download, install and use without a per use cost, or per publication cost.
I'm looking more for a plug-in for either Acrobat, or Indesign or stand alone program that would convert them without adding copyrights, or ads to the file.

How can I create clearer, sharper images and buttons in Muse?

How can I create buttons and images that have a vector like clarity? When I upload images (buttons, jpegs and pngs) a lot of the time they seem to have a slightly fuzzy quality to them. I have read previous posts on this matter and none have helped. Any feedback on this will be greatly appreciated. Thanks

When you place your images in exactly the size you saved them in Photoshop or whatever, Muse doesn’t touch it.
The quality in this case is the quality you saved the image.
The best way is, to examine in Muse the available pixel size of the image and then use Photoshop to obtain this size
A helpful widget to examine the potential size of an image in advance, is the "lore ipsum"-Muse-widget, that you find in the free widget collection "Andrew’s Prototypes":
Andrew Prototypes | Exchange | Adobe Muse CC

Fuzzy Buttons

Similar Messages

Maybe you are looking for