Fuzzy Logic 4 help!

How do I use Fuzzy Logic 4??
I can install it, I can run it but I am buggered if I can actually change anything, all I can do is look at temp, voltage, multiplier, fsb speed and CPU speed.
I thought this tool was to enable you to manipulate the CPU speed??
I have a K7N2-L mobo 2100XP (TB 'b') CPU and using win XP home.

How do I use Fuzzy Logic 4??, you ask...
The short answer is: you can't. It doesn't work with the nForce2, as MSI makes clear.
System:
Mecca Future Dreamers CP101
Thermaltake Purepower ATX420W
MSI K7N2G-L
BIOS 3.2
XP2000+ T'bred
1 x 256MB Spectek PC2700
Maxtor 40GB 7200RPM
JustCool internal HD cooler
Maxtor 6.4GB 5400RPM
Lite-On 32x12x40
NEC 100MB Zip drive
Win 2k Pro (SP 3)

Similar Messages

  • MOVED: KT333 Ultra; fuzzy logic, 1.6xp overclocking problem help !!!!!

    This topic has been moved to Overclockers & Modding Corner.
    KT333 Ultra; fuzzy logic, 1.6xp overclocking problem help !!!!!

    Not that I am an expert o/c but here are some thoughts on the matter.
    My comments are based on my experiences of the KT3 Ultra2 which is basically the same as the Ultra version.
    This mobo does not have the ability to lock the PCI/AGP bus freely from the FSB. However, it does have dividers. At 133 a 1/4 divider kicks in. Above 152FSB the 1/5 divider works, so that at 166 the PCI & AGP buses will be back in sync. If you are o/c your cpu, don't go from 133 to 145, etc since you will be running the PCI/AGP buses further out of whack. Just go to either the mid 150's or to 166 in one jump. The other problem / issue relates to your cpu. From what you say you have one of the old Palominos which are not great o/c's. I would personally o/c your cpu from the BIOS rather than 'Fluffy Logic' which I would tend to stay away from. 
    With a 166FSB cpu a very stable o/c would be 175-177 beyond 180 gets decidedly tricky.
    Hope this helps

  • Fuzzy Logic Toolkit

    I followed the truck maneuvering example in the 'PID Control Toolset User Manual' and tried to use the 'I/O-Characteristic' test facility. But, when I tried to run the test facility, I realized that there is no run & stop buttons in the window. By the way I did not do the exact the same things the book showed. For instance, the example uses 5 terms for one input and 7 for another one. I used 3 for both. But, I think basically I followed the most steps he mentions in the example. Do you have any idea what went wrong, or can you tell me how I can run the test facility?
    Airo

    Dear AdamB,
    I am just wondering if you could help me a bit. I have two problems. The first one is, I'm working with the fuzzy logic toolbox from matlab. I created a .fis file with some rules from the fuzzy editor in the fuzzy logic toolbox from matlab, wich I want to run in labview, with the matlab script. How can load the fis file? I tried with the examples attached, but it didn't work.
    The second problem is I have been doing some work with fuzzy logic toolbox in Matlab. The fuzzy inference system (FIS) built in Matlab environment is quite simple and straightforward. An example of the FIS in Matlab can be found in the attachment. Now I want to use the fuzzy logic toolkit from Labview to perform the same task. An example of the FIS in Labview can also be found attached. Although the FIS properties in Labview has been made the same as in Matlab, the result of the defuzzification is different. The FIS properties in Matlab are:
    And method: prod
    Or method: max
    Implication: Prod
    Aggregation: Sum
    Defuzzification: Centroid
    The FIS properties in Labview has been made:
    Defuzzification Method: Center of Gravitiy (which is another name for Centroid)
    If no rule is active: Take last value
    Inference Method: Max-Min
    Select form of rulebase: Normal rulebase
    For instance, if the input to FIS is Matlab is -3.51, the output is 0.202. However, with the same input, the output from FIS in Labview is 0.30.
    Perhaps you could help me?
    Dedy
    Attachments:
    fuzzy_test.zip ‏7 KB
    deltaR5.zip ‏2 KB

  • Fuzzy Logic - How do I get into it?

    When I click on the Fuzzy Logic .exe file, it says Fuzzy Logic or PC Alert already running...
    I See PC Alert and can look at/configure stuff, but where is Fuzzy Logic?
    And what can I do with it?

    You only can open one program at a time. Meaning if you open pc alert ..then you cannot open fuzzy logic and vice versa. Hope this helps.

  • Fuzzy logic controller design

    Hi,
    Is it possible to configure the "Fuzzy Logic Controller Design" with sending a code in another language of programmation like C for exemple and without need to access each time using : Tools > Control Design and Simulation > Fuzzy Logic Controller Design  ?????????????????????????????????

    I assume you have 3 terms for each of your 3 parameters then, to get the 27 rules. If this is the case, going to the rule-base editor will bring up all 27 rules (the control designer automatically populates the rules list, so you don't even have to add additional rules to reach this number). Consequences, unlike rules however, are limited to 9. When I asked what you are using the controller before, perhaps I should have been more specific, as I was more curious as to whether or not you need singletons for your consequences? I am still having trouble imagining a situation where you need 27 *consequences*, unless perhaps they are singletons.
    That being said, I don't know of a way to use the fuzzy logic kit to create a controller with more than 9 consequences (27 rules are no problem). How familiar are you with the mathematics and principles behind the fuzzy logic controller? It's always possible to write your own code, and if you need any help, I'd be more than willing to help out.
    -Cory

  • Problem with Fuzzy Logic Controller Design window

    Hi,
    I'm designing a fuzzy inference system using the Fuzzy Logic Controller Design tool.
    But when I use up to 4 input variables, the Rule Editor window is out of center and I cannot see the left parts of the antecedents.
    See the attached picture.
    The visualization is not movable and resizing the window with system utilities does not give any results.
    Anyody can help me? Thanks!
    Attachments:
    Bug Fuzzy Controller Design.JPG ‏68 KB

    Hello all
    The PID and Fuzzy Logic Toolkit 2009 was completely redesigned.
    There are new API VIs and a more intuitive user interface for creating controllers.
    You can create MIMO controllers with unlimited inputs and outputs, and also modify the controller on-the-fly.
    Check it out the new features and let us know your needs on Fuzzy control.
    LabVIEW PID and Fuzzy Logic Toolkit User Manual
    Regards,
    Bruno Cesar
    National Instruments

  • Fuzzy Logic 4 & 100% CPU Usage freeze

    Hi,
    is there any Fuzzy Logic 4 Version out there that works with KT3 Ultra2-R and XP?
    I tried 4.0.63.1 and 4.1.48.0 from the MSI Pages and the Version I got on CD
    4.0.63.1 just can't find the avi ...
    4.1.48.0 and the CD Version just add the Icon to the taskbar when starting and than take 100% CPU-Time and do nothing anymore.
    The Program is not even killable in Taskmanager so all I can do afterwards is wait 10 minutes until XP has shutdown with the leftover CPUtime.

    I understand the CS2 is probably not helping, but there is really a problem on other apps too - not only CS2 and those are universal.
    Page ins/outs are currently 142257/71109 and i have not been using or even opening CS2 - just safari, itunes, What size , MSEntourage, VLC and moving some files.
    I have taken some earlier advice on your posts regarding using multiple internal disks - so i moved itunes and iphoto libraries to a separate disk and also use that for scratch in CS2. The drives are 250GB WD and 250GB Seagate, and i am looking at replacing them with one or two 750GB WD RE2, although probably not in RAID ( dont want to complicate my life too much in one go !)
    Overall i think the page ins/outs look high from my searching in other posts, but can't see why it would be overloaded when i normally dont use the CS2 that much ( only a hobby)
    Also the private/var/vm directory has 3 swap files - two of 64 MB and one (Swapfile2) is 128MB, if that tells something else ?
    looks like i will have to invest in 4GB more memory as well as the HDD's. i was confused with the apparent further lack of support in CS3 for 64 bit programming (?) although i dont know when that would be launched so soon after CS3
    I have a case of a little knowledge ( which can be a dangerous thing!)
    Message was edited by: grahams

  • Fuzzy Logic Fuzzy Problem!!

    My system:
    MSI 694T Pro (6309) version 5 (celeron 1.1a)
    Windows XP Pro
    Fuzzy Logic 4 (latest version)
    Fuzzy logic is fuzzy, it has GUI problem and does not work. help!! ?(  ?(
    Screen shot:
    http://web.njit.edu/~yz5/fuzzy.jpg

    Hi I am having the same problem on Win2K. Have you fixed it?  Cheers Rui.

  • Display fuzzy logic firering rule in front panel?

    Hi all,
    I only can display the firering rule no. (attached 1.gif red circule) in front panel.
    How can I also display the firering rule no. detail infomation (attached 2.gif) in display panel?
    Can I show the .fc file (generate in Fuzzy Logic Controller Design)detail infomation in display panel?
    Thanks
    Fung
    Attachments:
    1.GIF ‏61 KB
    2.GIF ‏79 KB

    Stephen M,
    Attached .fc file. Please help!
    Thanks
    Fung
    Attachments:
    FuzzyDesign_v5_height.fc ‏3 KB

  • Fuzzy Logic 4 problem

    Like Dutch in a different post,  I have a 694 T Pro MB with a Celeron 1.1a.
     I installed Fuzzy Logic 4 in hopes that it would allow me to raise the FSB.
     It gives me a popup in both manual and automatic about privileged instruction, and won't let me raise anything.
     I can't even make the changes in the bios...It will try to reboot to the new fsb setting,
     but halfway through the start-up it reverts to original settings and restarts.
    This is a brand new version 5 tualatin board. What am I doing wrong that is locking this out?
    (This is a supported chip, with the yellow Tualatin label on the socket 370.)
    Thank you for any help and insights.

    I have the same problem with my M3-6368 and I can't stand it. What I don't understand is why the BIOS always reverts to the default setting. Hopefully this will be easy to fix with a simple BIOS update.

  • Fuzzy logic controller for DC motor

    Hello guys!
    Can anyone help me out in giving inputs to fuzzy controller which has two input member function Error and Change in error. Is there any tool which can store the previous error and compare it with present error which gives the chane in error?

    Hello,
    Please look at the shipping example of Fuzzy Logic Toolkit in:
    C:\Program Files\National Instruments\LabVIEW 2010\examples\control\fuzzy\Tanks with PI control\FuzzyEx Tanks with PI control.vi
    This code will allow you to see how you can implement the error and rate error by using pure LabVIEW code. Now, if you have the Control Design and Simulation Module, this tool have functions that easily calculate the error and derivative for you.
    Hope this helps
    PS: Notice that this example is in LabVIEW 2010. The same example can be found also in 2009 by changing the number of the LabVIEW version on the path to 2009. Previous versions have this code, but they are a bit more difficult to understand. If you have previous version of LV 2009, I strongly recommend you to update to at least 2009 since on this version the toolkit was completely refactored. If you can't here is the location of the example previous to 2009:
    C:\Program Files\National Instruments\LabVIEW 8.6\examples\control\fuzzy\tanks.llb\Tanks - fuzzy control PI.vi
    Barp - Control and Simulation Group - LabVIEW R&D - National Instruments

  • My project title is fuzzy logic controller for rotary crane. need to reduce sway of pendulum

    helo. i want to ask whether my block diagram is correct or not. there is no error occured but no waveform will generate. i give the picture of my block diagram and my front panel. really need help. big thanks!
    Attachments:
    macam jadik je.JPG ‏42 KB
    front panell.JPG ‏28 KB

    Please look at this post for instructions in how to use Fuzzy Logic with RT. However, notice that this only works with RT, not FPGA:
    http://forums.ni.com/t5/LabVIEW/Problem-of-using-fuzzy-in-my-project/m-p/1772362#M615631
    Hope this helps
    Barp - Control and Simulation Group - LabVIEW R&D - National Instruments

  • How to get Fuzzy Logic to keep it's settings?

    I'm having problems getting Fuzzy Logic 4 to keep the overclocking settings (i.e. FSB setting) after a restart.
    If I open FL4 and manually set the FSB to 160 Mhz my machine works great, very stable and fast. However, after every restart or reboot, FL is not active and I one again have to open FL4 manually and set the FSB. This is quite irritating...
    Even if I place a shortcut to FL4 in the "startup" folder the only thing that happens is that FL4 is started once windows has started but the FSB setting is back to normal, this happens even if I click "save" after setting the FSB in FL4.
    Is this normal, shouldn't FL4 keep its settings even after a restart?
    Is there a way to get it to keep the setting I make? Registry hack?
    Any help much appreciated...
    System specs:
    MS-6704 1.0 8845PE-Max2-FIR
    P4(2400)@2880 (with FSB 160)
    768 Mb PC3200 DRAM
    Windows XP Pro SP1

    a "save" button but FL doesn't start automatically when Windows restarts. Even if I manually make a shortcut to FL and place it in the "startup" folder the only thing that happens is that FL starts but even then it doesn't retain it's previous settings (even if the were "saved")...

  • Fuzzy Logic 4 Turbo problems

    Hi!
    I just tried to use Fuzzy Logic's auto clocking. It does this tests and then reboots. Then I read from manual that there should be someking of Turbo-button I can use after rebooting to use best possible clocking. My problem is that I don't have any Turbo-button! Can anyone help, please?

    if u want you can redownload it here(big link): link
    it is still better to overclock through the bios

  • Fuzzy Logic Development

    Sir,
    I have developed an inference system using the Labview fuzzy system designer. Now the .fs file has no block diagram with it.
    I want to add some VIs for the input and output and some graphic to make the system more user friendly
    How can i modify the fuzzy system designer file as its block diagram is not visible?
    Best Regards,
    Ali

    After you develop the Fuzzy Logic System using the Designer, you need to use the VI "FL Fuzzy Controller.vi" to implement the controller. The best way to see this is using the examples below: 
    C:\Program Files (x86)\National Instruments\LabVIEW 2013\examples\control\fuzzy\Car Parking\FuzzyEx Car Backward Parking.vi
    This example will show you how how implement a closed-loop controller with two fuzzy logic system running in different activities (forward and backward). and you can see this example:
    C:\Program Files (x86)\National Instruments\LabVIEW 2013\examples\control\fuzzy\Dynamic greenhouse controller\FuzzyEx Dynamic Fuzzy Controller for a greenhouse.vi
    This example shows how to change the paraemters othe fuzzy controller while it is running and also shows you how to create a multiple-input and multiple output controller.
    Hope this helps,
    Barp - Control and Simulation Group - LabVIEW R&D - National Instruments

Maybe you are looking for