Fuzzy Logic 4 Turbo problems

Hi!
I just tried to use Fuzzy Logic's auto clocking. It does this tests and then reboots. Then I read from manual that there should be someking of Turbo-button I can use after rebooting to use best possible clocking. My problem is that I don't have any Turbo-button! Can anyone help, please?

if u want you can redownload it here(big link): link
it is still better to overclock through the bios

Similar Messages

Fuzzy Logic 4 problem

Like Dutch in a different post, I have a 694 T Pro MB with a Celeron 1.1a.
I installed Fuzzy Logic 4 in hopes that it would allow me to raise the FSB.
It gives me a popup in both manual and automatic about privileged instruction, and won't let me raise anything.
I can't even make the changes in the bios...It will try to reboot to the new fsb setting,
but halfway through the start-up it reverts to original settings and restarts.
This is a brand new version 5 tualatin board. What am I doing wrong that is locking this out?
(This is a supported chip, with the yellow Tualatin label on the socket 370.)
Thank you for any help and insights.

I have the same problem with my M3-6368 and I can't stand it. What I don't understand is why the BIOS always reverts to the default setting. Hopefully this will be easy to fix with a simple BIOS update.

Fuzzy logic display problems

anyone else got a fix for the fuzzy logic 4 not being displayed on screen properly? all off alignment etc.
thanks

-yes
i had the same prob with the old fuzylogic version i tried back in january when i first put the box together.
everything else about this 'puter runs fine for the past 10 months. occasionally it makes me play unreal tournament too much and sometimes it tells me to ignore my family, but other than that its ok
I just tried the new live update version of fuzzy-l and its dejavu all over again...........

MOVED: KT333 Ultra; fuzzy logic, 1.6xp overclocking problem help !!!!!

This topic has been moved to Overclockers & Modding Corner.
KT333 Ultra; fuzzy logic, 1.6xp overclocking problem help !!!!!

Not that I am an expert o/c but here are some thoughts on the matter.
My comments are based on my experiences of the KT3 Ultra2 which is basically the same as the Ultra version.
This mobo does not have the ability to lock the PCI/AGP bus freely from the FSB. However, it does have dividers. At 133 a 1/4 divider kicks in. Above 152FSB the 1/5 divider works, so that at 166 the PCI & AGP buses will be back in sync. If you are o/c your cpu, don't go from 133 to 145, etc since you will be running the PCI/AGP buses further out of whack. Just go to either the mid 150's or to 166 in one jump. The other problem / issue relates to your cpu. From what you say you have one of the old Palominos which are not great o/c's. I would personally o/c your cpu from the BIOS rather than 'Fluffy Logic' which I would tend to stay away from.
With a 166FSB cpu a very stable o/c would be 175-177 beyond 180 gets decidedly tricky.
Hope this helps

Fuzzy Logic Fuzzy Problem!!

My system:
MSI 694T Pro (6309) version 5 (celeron 1.1a)
Windows XP Pro
Fuzzy Logic 4 (latest version)
Fuzzy logic is fuzzy, it has GUI problem and does not work. help!! ?( ?(
Screen shot:
http://web.njit.edu/~yz5/fuzzy.jpg

Hi I am having the same problem on Win2K. Have you fixed it? Cheers Rui.

Problem with Fuzzy Logic Controller Design window

Hi,
I'm designing a fuzzy inference system using the Fuzzy Logic Controller Design tool.
But when I use up to 4 input variables, the Rule Editor window is out of center and I cannot see the left parts of the antecedents.
See the attached picture.
The visualization is not movable and resizing the window with system utilities does not give any results.
Anyody can help me? Thanks!
Attachments:
Bug Fuzzy Controller Design.JPG ‏68 KB

Hello all
The PID and Fuzzy Logic Toolkit 2009 was completely redesigned.
There are new API VIs and a more intuitive user interface for creating controllers.
You can create MIMO controllers with unlimited inputs and outputs, and also modify the controller on-the-fly.
Check it out the new features and let us know your needs on Fuzzy control.
LabVIEW PID and Fuzzy Logic Toolkit User Manual
Regards,
Bruno Cesar
National Instruments

Fuzzy Logic Freezes

After downloading & trying Fuzzy Logic with my new 845PE Max 2 (XP Prof) with a P4 2.533, I found it goes to re-boot (as it should) but when I try to put it into "turbo" the computer freezes & I have to unplug the power & wait a while before turning it on again. The power & reset switches stop working! Can anyone advise what's happening here & hot to fix FZLogic so it will work?

Quote
Originally posted by Tribeca
After downloading & trying Fuzzy Logic with my new 845PE Max 2 (XP Prof) with a P4 2.533, I found it goes to re-boot (as it should) but when I try to put it into "turbo" the computer freezes & I have to unplug the power & wait a while before turning it on again. The power & reset switches stop working! Can anyone advise what's happening here & hot to fix FZLogic so it will work?
I have the same problem with my 645E Max 2 LRU with a P4 2.4 Northwood. When I try to put it into "turbo" FuzzyLogic4 the pc freezes. Can it be that these boards was designed for FuzzyLogic3 but is delivered with a utility-cd with FuzzyLogic 4? Please help - anybody!!

Fuzzy Logic Toolkit

I followed the truck maneuvering example in the 'PID Control Toolset User Manual' and tried to use the 'I/O-Characteristic' test facility. But, when I tried to run the test facility, I realized that there is no run & stop buttons in the window. By the way I did not do the exact the same things the book showed. For instance, the example uses 5 terms for one input and 7 for another one. I used 3 for both. But, I think basically I followed the most steps he mentions in the example. Do you have any idea what went wrong, or can you tell me how I can run the test facility?
Airo

Dear AdamB,
I am just wondering if you could help me a bit. I have two problems. The first one is, I'm working with the fuzzy logic toolbox from matlab. I created a .fis file with some rules from the fuzzy editor in the fuzzy logic toolbox from matlab, wich I want to run in labview, with the matlab script. How can load the fis file? I tried with the examples attached, but it didn't work.
The second problem is I have been doing some work with fuzzy logic toolbox in Matlab. The fuzzy inference system (FIS) built in Matlab environment is quite simple and straightforward. An example of the FIS in Matlab can be found in the attachment. Now I want to use the fuzzy logic toolkit from Labview to perform the same task. An example of the FIS in Labview can also be found attached. Although the FIS properties in Labview has been made the same as in Matlab, the result of the defuzzification is different. The FIS properties in Matlab are:
And method: prod
Or method: max
Implication: Prod
Aggregation: Sum
Defuzzification: Centroid
The FIS properties in Labview has been made:
Defuzzification Method: Center of Gravitiy (which is another name for Centroid)
If no rule is active: Take last value
Inference Method: Max-Min
Select form of rulebase: Normal rulebase
For instance, if the input to FIS is Matlab is -3.51, the output is 0.202. However, with the same input, the output from FIS in Labview is 0.30.
Perhaps you could help me?
Dedy
Attachments:
fuzzy_test.zip ‏7 KB
deltaR5.zip ‏2 KB

Fuzzy logic 4 doesn't work with the KT4-SR!

why ;( ?!

I also have problems running Fuzzy Logic.
I do not run any other utilities, and I have the latest version of it. When I run the program, it sits in the system tray, if I try to click on it, nothing happens. Taskmanager shows FL4 uses around 99% of the CPU. Aslo, when I shut down after running FL4, Win XP can take upto 10 mins to kill the app.
Does anyone have a fix, re-installing or upgrading FL4 doesn't work.
Alternativly, is there another program that can be used?
I have:
KT4 Ultra with AMD XP 2400+
Windows XP Pro / SP1
Thanks

Fuzzy logic controller design

Hi,
Is it possible to configure the "Fuzzy Logic Controller Design" with sending a code in another language of programmation like C for exemple and without need to access each time using : Tools > Control Design and Simulation > Fuzzy Logic Controller Design ?????????????????????????????????

I assume you have 3 terms for each of your 3 parameters then, to get the 27 rules. If this is the case, going to the rule-base editor will bring up all 27 rules (the control designer automatically populates the rules list, so you don't even have to add additional rules to reach this number). Consequences, unlike rules however, are limited to 9. When I asked what you are using the controller before, perhaps I should have been more specific, as I was more curious as to whether or not you need singletons for your consequences? I am still having trouble imagining a situation where you need 27 *consequences*, unless perhaps they are singletons.
That being said, I don't know of a way to use the fuzzy logic kit to create a controller with more than 9 consequences (27 rules are no problem). How familiar are you with the mathematics and principles behind the fuzzy logic controller? It's always possible to write your own code, and if you need any help, I'd be more than willing to help out.
-Cory

Fuzzy Logic 4 & 100% CPU Usage freeze

Hi,
is there any Fuzzy Logic 4 Version out there that works with KT3 Ultra2-R and XP?
I tried 4.0.63.1 and 4.1.48.0 from the MSI Pages and the Version I got on CD
4.0.63.1 just can't find the avi ...
4.1.48.0 and the CD Version just add the Icon to the taskbar when starting and than take 100% CPU-Time and do nothing anymore.
The Program is not even killable in Taskmanager so all I can do afterwards is wait 10 minutes until XP has shutdown with the leftover CPUtime.

I understand the CS2 is probably not helping, but there is really a problem on other apps too - not only CS2 and those are universal.
Page ins/outs are currently 142257/71109 and i have not been using or even opening CS2 - just safari, itunes, What size , MSEntourage, VLC and moving some files.
I have taken some earlier advice on your posts regarding using multiple internal disks - so i moved itunes and iphoto libraries to a separate disk and also use that for scratch in CS2. The drives are 250GB WD and 250GB Seagate, and i am looking at replacing them with one or two 750GB WD RE2, although probably not in RAID ( dont want to complicate my life too much in one go !)
Overall i think the page ins/outs look high from my searching in other posts, but can't see why it would be overloaded when i normally dont use the CS2 that much ( only a hobby)
Also the private/var/vm directory has 3 swap files - two of 64 MB and one (Swapfile2) is 128MB, if that tells something else ?
looks like i will have to invest in 4GB more memory as well as the HDD's. i was confused with the apparent further lack of support in CS3 for 64 bit programming (?) although i dont know when that would be launched so soon after CS3
I have a case of a little knowledge ( which can be a dangerous thing!)
Message was edited by: grahams

I searched and searched (fuzzy logic 4)

Hello!
Right now i was reading for over an hour and i cannot find the right answer about fuzzy logic 4
I used live update to get the most recent drivers for my mobo msi 845 pe max2.
(just to be complete I have the HT option in the bios while having a P4 2.4Ghz, for those who want to know, bios 1.20).....
My problem:
I used the "auto" function in fuzzy-logic and waited 3 minutes, the FSB is boosted to 164. Than the system hangs and restarts. (thats normal right?) the cpu-temp is 64C when it hangs..
then after the reboot, nothing has changed and the fsb is back to 133???
What is wrong? how can i overclock my system with fuzzy logic??
Sander

I would NOT use Core-Center Either with your Board, as since it is a 845 Series, I dont Believe that you even have the "Core-Cell" Chip on your Motherboard ..I suggest that you use "Speed-Fan" as this seems to be the Utility that Most of the Members have Success with, and if you want a Utility to Overclock your FSB with, Download Clock-Generator, at http://www.cpuid.com .....Sean REILLY875

Fuzzy logic in labview

Hey,
I try to design a fuzzy logic controller in LabVIEW 2009 for a air heating coil.i have two entries, error and error variation and i need the my fuzzy control to give variation order. The problem is the variation order is always 0 my rule base is not invoked, Can we tell my what are the possible causes ?

Stoleriu wrote:
Sorry i m new to this
No worries, please follow the link I included in my above comment. It will show you how to post a snippet here, so we can actually see the code in LabVIEW ourselves.
P.S. Dang, are you running utorrent on Windows 95? Haha

My project title is fuzzy logic controller for rotary crane. need to reduce sway of pendulum

helo. i want to ask whether my block diagram is correct or not. there is no error occured but no waveform will generate. i give the picture of my block diagram and my front panel. really need help. big thanks!
Attachments:
macam jadik je.JPG ‏42 KB
front panell.JPG ‏28 KB

Please look at this post for instructions in how to use Fuzzy Logic with RT. However, notice that this only works with RT, not FPGA:
http://forums.ni.com/t5/LabVIEW/Problem-of-using-fuzzy-in-my-project/m-p/1772362#M615631
Hope this helps
Barp - Control and Simulation Group - LabVIEW R&D - National Instruments

How to get Fuzzy Logic to keep it's settings?

I'm having problems getting Fuzzy Logic 4 to keep the overclocking settings (i.e. FSB setting) after a restart.
If I open FL4 and manually set the FSB to 160 Mhz my machine works great, very stable and fast. However, after every restart or reboot, FL is not active and I one again have to open FL4 manually and set the FSB. This is quite irritating...
Even if I place a shortcut to FL4 in the "startup" folder the only thing that happens is that FL4 is started once windows has started but the FSB setting is back to normal, this happens even if I click "save" after setting the FSB in FL4.
Is this normal, shouldn't FL4 keep its settings even after a restart?
Is there a way to get it to keep the setting I make? Registry hack?
Any help much appreciated...
System specs:
MS-6704 1.0 8845PE-Max2-FIR
P4(2400)@2880 (with FSB 160)
768 Mb PC3200 DRAM
Windows XP Pro SP1

a "save" button but FL doesn't start automatically when Windows restarts. Even if I manually make a shortcut to FL and place it in the "startup" folder the only thing that happens is that FL starts but even then it doesn't retain it's previous settings (even if the were "saved")...

Fuzzy Logic 4 Turbo problems

Similar Messages

Maybe you are looking for