FW400 not listed in System-Profiler

How can i update the Port, that i can connect my Projekt-Mix.

Can you paste what System Profiler says about FW here?
Do you have any other fW 400 devices?
Are there any other FW devices plugged in?
FireWire Bus:
Maximum Speed:          Up to 800 Mb/sec
OEM ATA Device 00:
Manufacturer:          NewerTech
Model:          0x0
GUID:          0x30E002E0001558
Maximum Speed:          Up to 800 Mb/sec
Connection Speed:          Up to 800 Mb/sec
Sub-units:
OEM ATA Device 00 Unit:
Unit Software Version:          0x10483
Unit Spec ID:          0x609E
Firmware Revision:          0x110
Product Revision Level:
Sub-units:
OEM ATA Device 00 SBP-LUN:
Capacity:          931.51 GB
Removable Media:          Yes
BSD Name:          disk5
Mac OS 9 Drivers:          No
Partition Map Type:          APM (Apple Partition Map)
S.M.A.R.T. status:          Not Supported
Volumes:
Leo2:
Capacity:          931.39 GB
Available:          215.98 GB
Writable:          Yes
File System:          Journaled HFS+
BSD Name:          disk5s3
Mount Point:          /
OXFORD IDE Device 1:
Manufacturer:          OWC Mercury Elite Pro AL
Model:          0x0
GUID:          0x1D202009202C0
Maximum Speed:          Up to 800 Mb/sec
Connection Speed:          Up to 800 Mb/sec
Sub-units:
OXFORD IDE Device 1 Unit:
Unit Software Version:          0x10483
Unit Spec ID:          0x609E
Firmware Revision:          0x102
Product Revision Level:          3.AA
Sub-units:
OXFORD IDE Device 1 SBP-LUN:
Capacity:          465.76 GB
Removable Media:          Yes
BSD Name:          disk2
Mac OS 9 Drivers:          No
Partition Map Type:          APM (Apple Partition Map)
S.M.A.R.T. status:          Not Supported
Volumes:
OSX8:
Capacity:          465.64 GB
Available:          357.53 GB
Writable:          Yes
File System:          Journaled HFS+
BSD Name:          disk2s3
Mount Point:          /Volumes/OSX8
Unknown Device:
Manufacturer:          Unknown
Model:          Unknown
Maximum Speed:          Up to 400 Mb/sec
Connection Speed:          Unknown

Similar Messages

Why are applications not listed in System Profiler?

Hi Apple Support Community,
System Profiler -> Software -> Applications displays "No information found." instead of the expected list of 64bit / 32bit applications installed. What could cause this and how can I get System Profiler to rescan the applications installed?
Thank you,
System Version:          Mac OS X 10.6.8 (10K549)
Kernel Version:          Darwin 10.8.0
64-bit Kernel and Extensions:          Yes

Discussion thread http://discussions.apple.com/message.jspa?messageID=11077939 suggests Applications are not displayed in System Profiler because I purposefully disabled Spotlight for performance reasons and the indexing of external drives.

L3 Cache disabled, non-functional or not listed in system profiler?

I have a 15" 1 ghz powerbook G4 titanium, and for as long as I can remember, the 1 MB L3 Cache it's supposed to have is not listed in the system profiler. It fails the power-on self test in OS 9, as well as the Apple Hardware test CD. IS there any way of investigating this? The machine seems to run okay, but i'm sure it's hindering the performance of it somehow...

Hi Les,
Welcome to Apple Discussions.
As far as "investigating" goes, you've done all you need to; three separate sources all indicating the same L3 failure is pretty solid evidence.
I'm sure you're correct that it affects performance; unfortunately, cache is soldered onto the logic board, so beyond replacing the logic board, there's nothing you can do. If you've lived with it this long, I'd continue to live with it and put the LB replacement money toward your next machine.

CI and QE not listed on System Profiler

Hi All, I just picked up a MBP 15" 2.4Ghz, NVidia 8800M GT 256M ram, Model A1226 late 2007/early 2008. It has a few very small vertical lines down the left side. I took it to the Apple store to check the GPU out and it passed. While looking at posts here and Google, it was suggested to disable Quartz Extreme. So I looked at System Profiler and Core Image and Quartz Extreme are not even listed.
NVIDIA GeForce 8600M GT:
Chipset Model: GeForce 8600M GT
Type: GPU
Bus: PCIe
PCIe Lane Width: x1
VRAM (Total): 256 MB
Vendor: NVIDIA (0x10de)
Device ID: 0x0407
Revision ID: 0x00a1
ROM Revision: 3175
Displays:
Color LCD:
Resolution: 1440 x 900
Pixel Depth: 32-Bit Color (ARGB8888)
Main Display: Yes
Mirror: Off
Online: Yes
Built-In: Yes
Display Connector:
Status: No Display Connected
Could the previous owner have disabled them? How do I get them back?
Any help,
Glynn

Just found my answer...Since ALL Intel cpu's support Quartz Extreme, it is no longer listed on a Snow Leopard Mac. The same is true for Core Image.
Cheers

Way to find transaction code - if not listed in system-- status

Hi friends
way to find transaction code - if not listed in system--> status
ex:
spro- sd - sales -sales documents- sales document item -define item categories
I didn't find T-code for this path from <b>system -->status</b>
Please let me know the ways to find out exact T- codes.
Thanks
Prasad

Hi Prasad, once you are in
spro- sd - sales -sales documents- sales document item -define item categories,
go to Additional Information-> Additional Information -> Display Key -> IMG Activity
this will show you a code, in this case SIMG_CFMENUOLSDVOV7
take last four caracters, this is transaction code: VOV7.
Please reward if you find this useful.
Regards,
Efren

Removing an account not listed in System Preferences Accounts?

Somehow I inadvertently created a second account on my iMac that shows as an option at startup. I think I did this with the startup disc somehow. It's not listed in System Preferences>Accounts. How do I get rid of it?

I tried the terminal command first. It returned this line:
dsebableroot: Command not found.
I then tried the instructions after the link http://support.apple.com/kb/HT1528?viewlocale=en_US
"Click the Finder icon in the Dock.
From the Go menu, choose Utilities.
Open Directory Utility.
Click the lock in the Directory Utility window.
Enter an administrator account name and password, then click OK.
Choose Disable Root User from the Edit menu."
However in the Edit menu, "Disable Root User" is not an option. "Enable Root User" is.

G$ FW800 stock optical drive not seen in System Profile - is it daid?

I added a USB PCI card (2.0) to my FW and shifted some files (Migration Assistant) to my FW by Firewire from an eMac and then I wanted to run Diskwarrior to sort it all out. My CDW/DVDR wouldn't open, either with the eject key or through Toast. Not recognized in Toast. Not recognized in System Profile either. I reset the PMU (cause I can), then tried to boot the DW CD from a Firewire LaCie drive. No good. I finally got the CD to start the FW by using "alt" on startup and waiting for it to find DW but after running all the tests, my drive still seems to be dead. Any more resets or something I can try?
Also, I took the card out and tried again but no good. Are the circuits for the drive and PCI somehow related? Did I cook a controller or something?
Guys, what's the scoop? or is it poop?

Ok, that's it. I read a few posts in the "...SuperDrive won't accept my CD.." section. and it seems some people are just swapping optical drives like mad, ready to accept that the kit is crap, and "...oh, well, I sure hope this one works better...".
But one guy had the brains to have a look inside. Turns out dust had accumulated in the drive and on the connectors, and when he cleaned them, and unplugged and replugged them, it worked fine. So that's what I did. Took it out and put it back in. Amazing the stuff I cleared out! I also un- and re-plugged the power cable and the data ribbon at the mutha board and bingo!. We have disk, and I can breathe again.
Recommend to others they pretend they've bought a new drive, do a remove and reinstall and be very fastidious. You may not need a new one after all. I just love it that stuff can still be FIXED!
Thanks to Lou and all of you who share your experiences. It's like my brain is suddenly soooo huge...

Replaced Superdrive Not Seen in System Profiler 10.5.1

I just noticed my replaced Superdrive ( Pioneer DVR-111D [Beige Bezel] 'SuperDrive' 16X DVD w/DL + CDRW Burner) does not show in System Profiler under 10.5.1. It did after replacement after using Patch Burn under 10.4.0. Now Patch Burn says that it is unnecessary under 10.5 (Leopard). Also, there is no burn button available with iTunes (08). I don't want to waste a DVD to experiment, so does anyone happen to know anything about this (Mr Totes or any of the resident SD specialists?). Any and all comments would be appreciated.
Thanks, Chris

Hi Chris,
Thanks for posting back with your pioneering (excuse the pun) experience.
cheers
mrtotes

SATA HD not recognized in system profiler

Hi, I have just fitted a Sonnet SATA controller card along with a Seagate 500GB harddrive.
Disk Utility recognizes the disk and it mounts.
In System Profiler>PCI Cards the SATA card is recognized but not the Drive is not seen in System Profiler>S-ATA Devices.
Why is this?

Drives connected to PCI controller cards apparently don't show up in Panther's or Tiger's ASP, so that's not an actual problem. Another G4 owner who recently added a Sonnet SATA card posted the same question here.

External USB not recognized on my iMac (intel) in Disk Utility, Finder as well as in Terminal diskutil list but is listed in System Profile, which includes the location ID of 0xfa400000 / 5. Can the location ID be used to restore USB identity ?

My 1TB Seagate external USB not recognized by my iMac (intel) in Disk Utility, nor in Finder as well as in Terminal "diskutil list" but it is listed within the System Profile, which includes the location ID of 0xfa400000 / 5. Can the location ID be used to restore the identity of my external USB ?

Hello JNotorious,
Thank you for using Apple Support Communities.
For more information, take a look at:
USB and FireWire Quick Assist
http://support.apple.com/kb/ht1151
Have a nice day,
Mario

USB drives show up on list in System Profiler, but not on desktop

Hi, I have a 2.0 USB hub with 2 external USB drives attached, and sometimes they show up on the desktop, sometimes they don"t. When they don't, I can find them in the System Profiler under USB, and when I click refresh, they still show up in the list but don't show up on the desk top, or in the device utility either. Is there some way to get them to "re-appear" on the desk top? I too only have 1 USB port that will run them, but this doesn't make them show up on the DT. Anyone have an idea of what to do?
Thanks in advance for any help!

Hi, no they don't. If I connect them one at a time, they are fine. Sometimes I can get them to show up, and they stay on the desktop until , for some reason, they disappear and I get a dialog that says this drive was not put away properly . . .. I put the computer to sleep, I unplug the hub, start up the computer, plug in the hub again, but can't find a consistent way to get them to show up!

Optical drive not recognized in system profile after hardware rebuild

This is an old MacBook Pro. Apple call it vintage.
Logic board died, so rather than consign it being a doorstop, I took out the logic board and "cooked" it to reflow the solder. It actually worked!
Just prior to this and just before the logic board completely bit the dust I'd inserted a DVD into the optical drive, where it sat and didn't read, wasn't recognized etc. I was trying to drop back down in OS as Lion was too resource hungry for the old machine, so it was an OS install disk. Panther I think?
So now I've got the logic board working, but I cannot remove the DVD. I tried all the tricks, including Terminal etc. On checking System Profile I noticed that the optical drive isn't even listed now. So my question is, is it possible I missed a connection etc when rebuilding the MBP after replacing the logic board? If so, thoughts on where I should look? Is there a way to "force" the OS to find the optical drive? Any thoughts on what to do?
I can't pull the optical drive as one of the screws is completely stripped and honestly, not sure if the laptop is even worth the cost of a replacement drive anyway.

Ok, that's it. I read a few posts in the "...SuperDrive won't accept my CD.." section. and it seems some people are just swapping optical drives like mad, ready to accept that the kit is crap, and "...oh, well, I sure hope this one works better...".
But one guy had the brains to have a look inside. Turns out dust had accumulated in the drive and on the connectors, and when he cleaned them, and unplugged and replugged them, it worked fine. So that's what I did. Took it out and put it back in. Amazing the stuff I cleared out! I also un- and re-plugged the power cable and the data ribbon at the mutha board and bingo!. We have disk, and I can breathe again.
Recommend to others they pretend they've bought a new drive, do a remove and reinstall and be very fastidious. You may not need a new one after all. I just love it that stuff can still be FIXED!
Thanks to Lou and all of you who share your experiences. It's like my brain is suddenly soooo huge...

Start Up Items (Listed on System Profiler)

Hi,
I have two macs. My Mac Mini is running on Tiger and MBP on Leopard. The Mini has 16 "start up items" listed on the systems profiler that I have no item what they do. My MBP only has 4.
How do I identify necessary from unnecessary start up items?
I would like to remove the items I do not need. (Faster start up and possible hacker crap).
Thank you....

This are the listed Start Up Items. Do you see any problemware?
Adobe Version Cue
Apache
Apple Share
AppServices
AuthServer
CrashReporter
Disks
FibreChannel
IFCStart
IPService
Metadata
NetworkTime
NFS
PrintingServices
Virex

Hard Drive not recognized by system profiler

A few months ago with the help of some of you I inserted a new hard drive and things are / were working just fine. I have just noticed that now in the system profiler it is not being recognized but my old one original one is at the 74 G capacity. I am using the hd due to I'm on here so why not showing up? I had also inserted a PCI card. All was recognized when I did it.
Message was edited by: Jan Olsen1

It shows up in du and I ran a verify disk and it was ok...
It is connected via pci card. This is the info gathered by DU:
Name : ATA ST3160815A Media
Type : Disk
Disk Identifier : disk1
Media Name : ATA ST3160815A Media
Media Type : Generic
Connection Bus : SCSI
Connection Type : External
Connection ID : SCSI Target ID 0, Logical Unit 0
Partition Type : Applepartitionscheme
Device Tree : pci/ACARD,6280M@3/@0:0
Writable : Yes
Ejectable : Yes
Mac OS 9 Drivers Installed : No
Location : External
Total Capacity : 149.1 GB (160,041,885,696 Bytes)
S.M.A.R.T. Status : Not Supported
Disk Number : 1
Partition Number : 0

DVD stuck, drive not recognized in system profiler, can't eject, HELP!

I am distraught, my DVD/CD drive is quite sick, if not dead. Alright, I watch DVDs on my computer somewhat regularly, but this one time I was about an hour into a movie when it just stopped playing. I couldn't finish the movie because now my computer doesn't recognize the disc or even the fact that it has a DVD/CD drive at all. The DVD doesn't appear on the desktop and the eject button doesn't do anything, it's been stuck my drive for maybe a month or so and I forgot about it for a while actually.
The scariest thing is that when I check my system profiler I can't find any info about my DVD drive. When I click on disc burning, it says I dont have a disc burning device installed.
I've tried resetting the power manager (PMU) but to no avail. I would really like to solve this without taking my computer somewhere.
Any suggestions?

Welcome to Apple Discussions
Simple step first. If the "stuck" is due to a software problem, restart the computer holding down the click pad through the start-up until the disk ejects. This usually ejects anything in the drive.
You'll find other suggestions here (Donald Worrell post).
If none of the above suggestion work, you'll need to get a technician (Apple certified, if still under warranty) to look at the machine. If the DVD ejects, but the profiler still does not recognize the drive, then a trip to the Technician is your only recourse.

FW400 not listed in System-Profiler

Similar Messages

Maybe you are looking for