FWSM move from Active/Standby to Active/active
Hi there,
we have some FWSM installed in 6500 with many contexts in them. They are at the moment configured as Active/Standby and in production. But we have noticed that whenever a backup is run which goes through some of the contexts, the FWSM start counting errors which was already determined to be an oversubscription issue. So, while we wait for the new ASA 5585X to arrive and finally replace them, we want to mitigate the issue by configuring the FWSM as Active/Active and move the contexts for backup traffic to the other box (keeping the production contexts in the other one).
My question is, can this be done without impacting the production traffic? Or as soon as we enable the active/active by the configuration of the groups and assignments of the contexts, the traffic will be impacted and we will produce an outage to the network?
Thanks in advance for your help.
Regards,
Paula
So no answers?
Just one to update why had problem here: we need to to pull changes from Physical StandBy, because of performance reasons we cannot afford to reload every table with full refresh, we only want to get changes. At first I thought that it will be easy just create materialized view log and do basic replication, but in Physical StandBy we cant do it
Similar Messages
-
Issue in configuring Standby Database from Active database in 11g by RMAN
POSTED THE SAME IN DATA GUARD CATEGORY UNABLE TO DELETE
Hi All,
I am facing issue in creating the standby database from Active database using RMAN and getting the below issue after i executed the duplicate command.
Version of Database:11g(11.2.0.1.0)
Operating System:Linux 5
Error:
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of Duplicate Db command at 12/21/2012 17:26:52
RMAN-03015: error occurred in stored script Memory Script
RMAN-04006: error from auxiliary database: ORA-12514: TNS:listener does not currently know of service requested in connect descriptor
Primary Database Entries:
Tnsentry:
SONYPRD =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.20.131)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = sonyprd.localdomain)(UR=A)
SONYPRDSTBY =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.20.132)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = sonyprdstby)(UR=A)
Listner Entry:
SID_LIST_SONYPRD =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtproc)
(ORACLE_HOME = /u01/app/oracle/product/11.2.0/dbhome_1)
(PROGRAM = extproc)
(SID_DESC =
(SID_NAME = SONYPRD)
(GLOBAL_DBNAME = SONYPRD)
Auxiliary Details:
Tns Entry:
SONYPRD =
(DESCRIPTION =
# (ADDRESS = (PROTOCOL = TCP)(HOST = oracle11g.localdomain)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.20.131)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = sonyprd.localdomain)
SONYPRDSTBY =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.20.132)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = sonyprdstby)(UR=A)
Listener Entry in auxiliary:
SID_LIST_SONYPRDSTBY =
(SID_LIST =
(SID_DESC =
(GLOBAL_DBNAME = SONYPRDSTBY)
(ORACLE_HOME = /u01/app/oracle/product/11.2.0/dbhome_1)
(SID_NAME = SONYPRDSTBY)
TNSPING from Primary DB:
[oracle@oracle11g ~]$ tnsping sonyprdstby
TNS Ping Utility for Linux: Version 11.2.0.1.0 - Production on 21-DEC-2012 17:39:28
Copyright (c) 1997, 2009, Oracle. All rights reserved.
Used parameter files:
/u01/app/oracle/product/11.2.0/dbhome_1/network/admin/sqlnet.ora
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.20.132)(PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = sonyprdstby)(UR=A)))
OK (0 msec)
TNSPING from Auxuliary server
[oracle@oracle11gstby ~]$ tnsping sonyprd
TNS Ping Utility for Linux: Version 11.2.0.1.0 - Production on 21-DEC-2012 17:40:19
Copyright (c) 1997, 2009, Oracle. All rights reserved.
Used parameter files:
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.20.131)(PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = sonyprd.localdomain)))
OK (10 msec)
Script Used for duplicate:
run {
allocate channel prmy1 type disk;
allocate channel prmy2 type disk;
allocate channel prmy3 type disk;
allocate channel prmy4 type disk;
allocate auxiliary channel stby type disk;
duplicate target database for standby from active database
spfile
parameter_value_convert 'sonyprd','sonyprdstby'
set db_unique_name='sonyprdstby'
set db_file_name_convert='/sonyprd/','/sonyprdstby/'
set log_file_name_convert='/sonyprd/','/sonyprdstby/'
set control_files='/u01/app/oracle/oradata/control01.ctl'
set log_archive_max_processes='5'
set fal_client='sonyprdstby'
set fal_server='sonyprd'
set standby_file_management='AUTO'
set log_archive_config='dg_config=(sonyprd,sonyprdstby)'
set log_archive_dest_2='service=sonyprd ASYNC valid_for=(ONLINE_LOGFILE,PRIMARY_ROLE) db_unique_name=sonyprd'
Tried the script from both Primary and auxiliary but no luck
[oracle@oracle11gstby admin]$ rman target sys/welcome@sonyprd auxiliary sys/*****@sonyprdstby
Recovery Manager: Release 11.2.0.1.0 - Production on Fri Dec 21 17:26:24 2012
Copyright (c) 1982, 2009, Oracle and/or its affiliates. All rights reserved.
connected to target database: SONYPRD (DBID=3131093559)
connected to auxiliary database: SONYPRD (not mounted)
Listener Status from primary:
[oracle@oracle11g ~]$ lsnrctl status
LSNRCTL for Linux: Version 11.2.0.1.0 - Production on 21-DEC-2012 18:08:56
Copyright (c) 1991, 2009, Oracle. All rights reserved.
Connecting to (ADDRESS=(PROTOCOL=tcp)(HOST=)(PORT=1521))
STATUS of the LISTENER
Alias LISTENER
Version TNSLSNR for Linux: Version 11.2.0.1.0 - Production
Start Date 20-DEC-2012 17:42:17
Uptime 1 days 0 hr. 26 min. 41 sec
Trace Level off
Security ON: Local OS Authentication
SNMP OFF
Listener Parameter File /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/listener.ora
Listener Log File /u01/app/oracle/diag/tnslsnr/localhost/listener/alert/log.xml
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(KEY=EXTPROC1521)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=localhost.localdomain)(PORT=1521)))
Services Summary...
Service "sonyprd.localdomain" has 1 instance(s).
Instance "sonyprd", status READY, has 1 handler(s) for this service...
Service "sonyprdXDB.localdomain" has 1 instance(s).
Instance "sonyprd", status READY, has 1 handler(s) for this service...
The command completed successfully
Listener Status from Standby when database bring to Nomount state:
[oracle@oracle11gstby admin]$ lsnrctl status
LSNRCTL for Linux: Version 11.2.0.1.0 - Production on 21-DEC-2012 18:11:54
Copyright (c) 1991, 2009, Oracle. All rights reserved.
Connecting to (ADDRESS=(PROTOCOL=tcp)(HOST=)(PORT=1521))
STATUS of the LISTENER
Alias LISTENER
Version TNSLSNR for Linux: Version 11.2.0.1.0 - Production
Start Date 21-DEC-2012 16:13:47
Uptime 0 days 1 hr. 58 min. 6 sec
Trace Level off
Security ON: Local OS Authentication
SNMP OFF
Listener Parameter File /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/listener.ora
Listener Log File /u01/app/oracle/diag/tnslsnr/oracle11gstby/listener/alert/log.xml
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=oracle11gstby)(PORT=1521)))
Services Summary...
Service "sonyprdstby" has 1 instance(s).
Instance "sonyprdstby", status BLOCKED, has 1 handler(s) for this service...
The command completed successfully
Please provide any work arounds to proceed further in creating the standby database.
Thanks,
Ram.
Edited by: 895188 on Dec 21, 2012 5:50 PM
Edited by: 895188 on Dec 21, 2012 6:09 PM
Edited by: 895188 on Dec 21, 2012 6:22 PMHello;
Script has to be run from auxiliary.
Great details, but what I don't see is how you connect in RMAN.
Example
Start RMAN
$ORACLE_HOME/bin/rman target=sys/@recover2 auxiliary=sys/@reclone
Recovery Manager: Release 11.2.0.2.0 - Production on Wed Feb 22 14:50:31 2012
Copyright (c) 1982, 2009, Oracle and/or its affiliates. All rights reserved.
connected to target database: RECOVER2 (DBID=3806912436)
connected to auxiliary database: RECLONE (not mounted)Nothing in your tnsnames or listener jumps out as wrong. I copied them into my text editor and compared against my working ones.
Generally for active duplication I start the future standby on a pfile NOMOUNT.
Auxiliary Instance Initialization Parameters Needed :
DB_NAME
CONTROL_FILES
DB_BLOCK_SIZE
( add extra parameters like DB_FILE_NAME_CONVERT and LOG_FILE_NAME_CONVERT instead of using the SET command - clean up standby spfile right after duplication )
Then start RMAN and finally run a single line duplication command.
$ORACLE_HOME/bin/rman target=sys/@primary auxiliary=sys/@standby
RMAN>duplicate target database for standby from active database NOFILENAMECHECK;Best Regards
mseberg -
Issue in creating the standby database from Active database using RMAN
Hi All,
I am facing issue in creating the standby database from Active database using RMAN and getting the below issue after i executed the duplicate command.
Version of Database:11g(11.2.0.1.0)
Operating System:Linux 5
Error:
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of Duplicate Db command at 12/21/2012 17:26:52
RMAN-03015: error occurred in stored script Memory Script
RMAN-04006: error from auxiliary database: ORA-12514: TNS:listener does not currently know of service requested in connect descriptor
Primary Database Entries:
Tnsentry:
SONYPRD =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.20.131)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = sonyprd.localdomain)(UR=A)
SONYPRDSTBY =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.20.132)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = sonyprdstby)(UR=A)
Listner Entry:
SID_LIST_SONYPRD =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtproc)
(ORACLE_HOME = /u01/app/oracle/product/11.2.0/dbhome_1)
(PROGRAM = extproc)
(SID_DESC =
(SID_NAME = SONYPRD)
(GLOBAL_DBNAME = SONYPRD)
Auxiliary Details:
Tns Entry:
SONYPRD =
(DESCRIPTION =
# (ADDRESS = (PROTOCOL = TCP)(HOST = oracle11g.localdomain)(PORT = 1521))
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.20.131)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = sonyprd.localdomain)
SONYPRDSTBY =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.20.132)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = sonyprdstby)(UR=A)
Listener Entry in auxiliary:
SID_LIST_SONYPRDSTBY =
(SID_LIST =
(SID_DESC =
(GLOBAL_DBNAME = SONYPRDSTBY)
(ORACLE_HOME = /u01/app/oracle/product/11.2.0/dbhome_1)
(SID_NAME = SONYPRDSTBY)
TNSPING from Primary DB:
[oracle@oracle11g ~]$ tnsping sonyprdstby
TNS Ping Utility for Linux: Version 11.2.0.1.0 - Production on 21-DEC-2012 17:39:28
Copyright (c) 1997, 2009, Oracle. All rights reserved.
Used parameter files:
/u01/app/oracle/product/11.2.0/dbhome_1/network/admin/sqlnet.ora
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.20.132)(PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = sonyprdstby)(UR=A)))
OK (0 msec)
TNSPING from Auxuliary server
[oracle@oracle11gstby ~]$ tnsping sonyprd
TNS Ping Utility for Linux: Version 11.2.0.1.0 - Production on 21-DEC-2012 17:40:19
Copyright (c) 1997, 2009, Oracle. All rights reserved.
Used parameter files:
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = 192.168.20.131)(PORT = 1521)) (CONNECT_DATA = (SERVER = DEDICATED) (SERVICE_NAME = sonyprd.localdomain)))
OK (10 msec)
Script Used for duplicate:
run {
allocate channel prmy1 type disk;
allocate channel prmy2 type disk;
allocate channel prmy3 type disk;
allocate channel prmy4 type disk;
allocate auxiliary channel stby type disk;
duplicate target database for standby from active database
spfile
parameter_value_convert 'sonyprd','sonyprdstby'
set db_unique_name='sonyprdstby'
set db_file_name_convert='/sonyprd/','/sonyprdstby/'
set log_file_name_convert='/sonyprd/','/sonyprdstby/'
set control_files='/u01/app/oracle/oradata/control01.ctl'
set log_archive_max_processes='5'
set fal_client='sonyprdstby'
set fal_server='sonyprd'
set standby_file_management='AUTO'
set log_archive_config='dg_config=(sonyprd,sonyprdstby)'
set log_archive_dest_2='service=sonyprd ASYNC valid_for=(ONLINE_LOGFILE,PRIMARY_ROLE) db_unique_name=sonyprd'
Tried the script from both Primary and auxiliary but no luck
[oracle@oracle11gstby admin]$ rman target sys/welcome@sonyprd auxiliary sys/*****@sonyprdstby
Recovery Manager: Release 11.2.0.1.0 - Production on Fri Dec 21 17:26:24 2012
Copyright (c) 1982, 2009, Oracle and/or its affiliates. All rights reserved.
connected to target database: SONYPRD (DBID=3131093559)
connected to auxiliary database: SONYPRD (not mounted)
Listener Status from primary:
[oracle@oracle11g ~]$ lsnrctl status
LSNRCTL for Linux: Version 11.2.0.1.0 - Production on 21-DEC-2012 18:08:56
Copyright (c) 1991, 2009, Oracle. All rights reserved.
Connecting to (ADDRESS=(PROTOCOL=tcp)(HOST=)(PORT=1521))
STATUS of the LISTENER
Alias LISTENER
Version TNSLSNR for Linux: Version 11.2.0.1.0 - Production
Start Date 20-DEC-2012 17:42:17
Uptime 1 days 0 hr. 26 min. 41 sec
Trace Level off
Security ON: Local OS Authentication
SNMP OFF
Listener Parameter File /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/listener.ora
Listener Log File /u01/app/oracle/diag/tnslsnr/localhost/listener/alert/log.xml
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(KEY=EXTPROC1521)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=localhost.localdomain)(PORT=1521)))
Services Summary...
Service "sonyprd.localdomain" has 1 instance(s).
Instance "sonyprd", status READY, has 1 handler(s) for this service...
Service "sonyprdXDB.localdomain" has 1 instance(s).
Instance "sonyprd", status READY, has 1 handler(s) for this service...
The command completed successfully
Listener Status from Standby when database bring to Nomount state:
[oracle@oracle11gstby admin]$ lsnrctl status
LSNRCTL for Linux: Version 11.2.0.1.0 - Production on 21-DEC-2012 18:11:54
Copyright (c) 1991, 2009, Oracle. All rights reserved.
Connecting to (ADDRESS=(PROTOCOL=tcp)(HOST=)(PORT=1521))
STATUS of the LISTENER
Alias LISTENER
Version TNSLSNR for Linux: Version 11.2.0.1.0 - Production
Start Date 21-DEC-2012 16:13:47
Uptime 0 days 1 hr. 58 min. 6 sec
Trace Level off
Security ON: Local OS Authentication
SNMP OFF
Listener Parameter File /u01/app/oracle/product/11.2.0/dbhome_1/network/admin/listener.ora
Listener Log File /u01/app/oracle/diag/tnslsnr/oracle11gstby/listener/alert/log.xml
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=oracle11gstby)(PORT=1521)))
Services Summary...
Service "sonyprdstby" has 1 instance(s).
Instance "sonyprdstby", status BLOCKED, has 1 handler(s) for this service...
The command completed successfully
Please provide any work arounds to proceed further in creating the standby database.
Thanks,
Ram.Pl do not post duplicates - Issue in configuring Standby Database from Active database in 11g by RMAN
-
RMAN 11gR2 DUPLICATE TARGET FOR STANDBY FROM ACTIVE DATABASE - Issue -HELP
First question.
Can primary and standby database have the same SID name?
As I recall it is yes.
I believe they must have different GLOBAL or DB_UNIQUE_NAME?
Anyway, RMAN I believe is telling me it is having problems copying control file on first and dies.
Permissions Issue on STANDBY machine?
RMAN> connect target backup_admin/backup_admin
connected to target database: LABDG (DBID=1973403623)
RMAN> connect auxiliary sys/oracle@STANDBY;
connected to auxiliary database: LABDG (not mounted)
RMAN> DUPLICATE TARGET DATABASE FOR STANDBY FROM ACTIVE DATABASE;
Starting Duplicate Db at 18-JUL-11
using target database control file instead of recovery catalog
allocated channel: ORA_AUX_DISK_1
channel ORA_AUX_DISK_1: SID=10 device type=DISK
contents of Memory Script:
backup as copy reuse
targetfile '/u01/app/oracle/product/11.2.0/dbhome_1/dbs/orapwLABDG' auxiliar
'/u01/app/oracle/product/11.2.0/dbhome_1/dbs/orapwLABDG' ;
executing Memory Script
Starting backup at 18-JUL-11
allocated channel: ORA_DISK_1
channel ORA_DISK_1: SID=151 device type=DISK
Finished backup at 18-JUL-11
contents of Memory Script:
backup as copy current controlfile for standby auxiliary format '/u01/oradat
restore clone controlfile to '/u01/app/oracle/flash_recovery_area/LABDG/cont
'/u01/oradata/LABDG/control01.ctl';
executing Memory Script
Starting backup at 18-JUL-11
using channel ORA_DISK_1
channel ORA_DISK_1: starting datafile copy
copying standby control file
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of Duplicate Db command at 07/18/2011 11:20:54
RMAN-03015: error occurred in stored script Memory Script
RMAN-03009: failure of backup command on ORA_DISK_1 channel at 07/18/2011 11:20:
ORA-17628: Oracle error 19505 returned by remote Oracle serverHi,
Permissions Issue on STANDBY machine?First problem I see is the sysdba password must be the same on both sides (target and auxiliary dbs).
From the documentation.
The source database and auxiliary instances must use the same SYSDBA password, which means that both instances must have password files. You can
create the password file with a single password so you can start the auxiliary instance and enable the source database to connect to it.Check all prereqs for the standby db duplicate here.
http://download.oracle.com/docs/cd/E11882_01/backup.112/e10643/rcmsynta020.htm#i81724
Rgds,
Tycho -
Hello,
I am attempting to create a physical standby database, following this guide:
http://www.oracle.com/global/uk/education/downloads/uwe_data_guard.pdf
as well as the oracle documentation on Data Guard. Using Oracle 11gR2 patched at #7 running on Windows Server 2008.
I've set all the parameters, created password files and checked connectivity. Hopefully correctly. I will post pfile exports at the end.
Here is where I hit a dead end.
RMAN> connect target system/password@HPROD89
connected to target database : HPROD89 (DBID)
RMAN> connect auxiliary sys/password@HPROD89STND
connected to auxiliary database: HPROD89STND (not mounted)
RMAN> duplicate target database for standby from active database;Error from spool. I need to spool the file to get the error code, otherwise the only thing rman provides is a "error message stack follows" message with nothing after that.
RMAN-03002: failure of Duplicate Db command at 11/19/2010 21:24:04
RMAN-06136: ORACLE error from auxiliary database: ORA-03114: not connected to ORACLEI'm running rman on the standby server with the database in NOMOUNT as the guide linked above suggests. This raises a simple question to start with: what server do I run rman on? The one with the primary database, or on the standby?
I hope it's just because it's getting late, but this issue has me confused .. rman clearly connects the auxiliary, but when trying to perform the actual duplication, it's not connected.
Thanks for input.
Regards.primary parameters:
hprod89.__db_cache_size=3825205248
hprod89.__java_pool_size=33554432
hprod89.__large_pool_size=33554432
hprod89.__oracle_base='C:\app\oracle'#ORACLE_BASE set from environment
hprod89.__pga_aggregate_target=4127195136
hprod89.__sga_target=6375342080
hprod89.__shared_io_pool_size=0
hprod89.__shared_pool_size=2415919104
hprod89.__streams_pool_size=0
*._gby_hash_aggregation_enabled=FALSE
*._unnest_subquery=FALSE
*.audit_file_dest='C:\app\oracle\admin\HPROD89\adump'
*.audit_trail='db'
*.compatible='11.2.0.0.0'
*.control_files='E:\oracle\oradata\HPROD89\controlfiles\control01.ctl','E:\oracle\oraflash\HPROD89\controlfiles\control02.ctl'
*.db_block_size=8192
*.db_domain='ad.rferl.org'
*.db_file_name_convert='E:\oracle\oradata\HPROD89STND\datafiles\','E:\oracle\oradata\HPROD89\datafiles\'
*.db_files=1021
*.db_name='HPROD89'
*.db_recovery_file_dest='E:\oracle\oraflash'
*.db_recovery_file_dest_size=104857600000
*.diagnostic_dest='C:\app\oracle'
*.dispatchers='(PROTOCOL=TCP) (SERVICE=HPROD89XDB)'
*.fal_server='HPROD89STND'
*.log_archive_config='dg_config=(HPROD89, HPROD89STND)'
*.log_checkpoint_interval=0
*.log_checkpoint_timeout=0
*.log_file_name_convert='E:\oracle\oradata\HPROD89STND\redologs\','E:\oracle\oradata\HPROD89\redologs\'
*.memory_target=10485760000
*.nls_language='ENGLISH'
*.nls_length_semantics='CHAR'
*.nls_territory='CZECH REPUBLIC'
*.open_cursors=300
*.processes=150
*.remote_login_passwordfile='EXCLUSIVE'
*.standby_file_management='AUTO'
*.undo_tablespace='UNDOTBS1'
standby:
hprod89stnd.__db_cache_size=5100273664
hprod89stnd.__java_pool_size=33554432
hprod89stnd.__large_pool_size=33554432
hprod89stnd.__oracle_base='C:\app\oracle'#ORACLE_BASE set from environment
hprod89stnd.__pga_aggregate_target=4227858432
hprod89stnd.__sga_target=6274678784
hprod89stnd.__shared_io_pool_size=0
hprod89stnd.__shared_pool_size=1040187392
hprod89stnd.__streams_pool_size=0
*._gby_hash_aggregation_enabled=FALSE
*._unnest_subquery=FALSE
*.audit_file_dest='C:\app\oracle\admin\HPROD89STND\adump'
*.audit_trail='db'
*.compatible='11.2.0.0.0'
*.control_files='E:\oracle\oradata\HPROD89STND\controlfiles\control01.ctl','E:\oracle\oraflash\HPROD89STND\controlfiles\control02.ctl'
*.db_block_size=8192
*.db_domain=''
*.db_file_name_convert='E:\oracle\oradata\HPROD89\datafiles\','E:\oracle\oradata\HPROD89STND\datafiles\'
*.db_files=1021
*.db_name='HPROD89S'
*.db_recovery_file_dest='E:\oracle\oraflash'
*.db_recovery_file_dest_size=104857600000
*.db_unique_name='HPROD89STND'
*.diagnostic_dest='C:\app\oracle'
*.dispatchers='(PROTOCOL=TCP) (SERVICE=HPROD89STNDXDB)'
*.log_checkpoint_interval=0
*.log_checkpoint_timeout=0
*.log_file_name_convert='E:\oracle\oradata\HPROD89\redologs\','E:\oracle\oradata\HPROD89STND\redologs\'
*.memory_target=10485760000
*.nls_language='ENGLISH'
*.nls_length_semantics='CHAR'
*.nls_territory='CZECH REPUBLIC'
*.open_cursors=300
*.processes=150
*.remote_login_passwordfile='EXCLUSIVE'
*.undo_tablespace='UNDOTBS1' -
When executing 'duplicate target database for standby from active' the system tablespace/datafile (datafile 1) is not cloned. All other datafiles clone successfully. The RMAN process aborts with the following errors while attempting to clone the system tablespace/datafile.
ORA-19558: error de-allocating device
ORA-19557: device error, device type: DISK, device name:
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-03135: connection lost contact
Here are the details:
Primary is 11.2.0.2 RAC database on an Exadata platform
Standby is 11.2.0.2 Single Instance database (same patch level as primary) on a Red Hat Linux box
This is an ASM to ASM duplication.
This is not unique to this database. We tried another database and go the same behavior - all datafiles clone successfully with the exception of the system tablespace/datafile.
We have traced the RMAN execution and it seems to fail when it is trying to assign a NEWNAME to the system tablespace/datafile.
We even issued an explicit SET NEWNAME command but RMAN ignored it.
We also shutdown the primary and started is up in mount mode thinking that something had ahold of the System Tablespace/datafile.
We also opened up the network firewall to allow permit any,any traffic.
We increased the max_server_processes
and added TCP.NODELAY=yes to the sqlnet.ora file.
There seems to be some artifact present in our Primary System tablespace/data file that is preventing it form being cloned.
checked all alert files grid, asm, and dbhome - no abnormal messages.
We are in the process of restoring the database from a backup but we would prefer to get this working using the 'Active Database' methodologyI successfully created the standby database using RMAN backup and recovery.
I started the managed recovery. Archive logs are being sent from the primary to the standby ( I can see them in ASM), but the standby is not applying them.
I get the following messages in the standby alert log...
Fetching gap sequence in thread 2, gap sequence 154158-154257
Tue Nov 26 16:19:58 2013
Using STANDBY_ARCHIVE_DEST parameter default value as USE_DB_RECOVERY_FILE_DEST
Using STANDBY_ARCHIVE_DEST parameter default value as USE_DB_RECOVERY_FILE_DEST
Tue Nov 26 16:20:01 2013
Fetching gap sequence in thread 2, gap sequence 154158-154257
Tue Nov 26 16:20:11 2013
Fetching gap sequence in thread 2, gap sequence 154158-154257
Tue Nov 26 16:20:22 2013
Fetching gap sequence in thread 2, gap sequence 154158-154257
Tue Nov 26 16:20:32 2013
Fetching gap sequence in thread 2, gap sequence 154158-154257
I don't see any MRP processes:
select process,
status,
thread#,
sequence#,
block#,
blocks
7 from v$managed_standby;
PROCESS STATUS THREAD# SEQUENCE# BLOCK# BLOCKS
ARCH CLOSING 2 154363 1 132
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
RFS IDLE 0 0 0 0
RFS IDLE 1 145418 121 1
RFS IDLE 0 0 0 0
PROCESS STATUS THREAD# SEQUENCE# BLOCK# BLOCKS
RFS IDLE 0 0 0 0
12 rows selected.
SQL> SELECT THREAD#, SEQUENCE#, APPLIED FROM V$ARCHIVED_LOG;
THREAD# SEQUENCE# APPLIED
2 154356 NO
2 154357 NO
1 145411 NO
2 154358 NO
2 154360 NO
2 154361 NO
1 145414 NO
1 145415 NO
2 154362 NO
2 154363 NO
1 145416 NO
11 rows selected.
I do have the archive logs that cover sequences 154158-154257
Crosschecked 38 objects
Crosschecked 62 objects
Finished implicit crosscheck backup at 26-NOV-13
Starting implicit crosscheck copy at 26-NOV-13
using channel ORA_DISK_1
using channel ORA_DISK_2
Crosschecked 2 objects
archived log file name=+RECO_XORA/nmuasb00/archivelog/2013_11_26/thread_2_seq_154377.344.832521989 RECID=29 STAMP=832521990
validation succeeded for archived log
archived log file name=+RECO_XORA/nmuasb00/archivelog/2013_11_26/thread_2_seq_154378.346.832521991 RECID=31 STAMP=832521993
Crosschecked 31 objects -
RMAN DUPLICATE FOR STANDBY FROM ACTIVE DATABASE fails
Hello
I'm trying to use RMAN DUPLICATE to create a standby database using Oracle 11.2.0.3 with PSU 6 on HP-UX.
Primary is 2 node RAC. Standby is also 2 node RAC.
Standby database instance is started in nomount mode.
I use:
duplicate target database for standby from active database
spfile
<some spfile parameters>
with PFILE I get:
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of Duplicate Db command at 10/01/2013 12:41:13
RMAN-05501: aborting duplication of target database
RMAN-03015: error occurred in stored script Memory Script
RMAN-03009: failure of sql command on clone_default channel at 10/01/2013 12:41:13
RMAN-11003: failure during parse/execution of SQL statement: alter system set spfile= '/opt/oracle/db11203/dbs/spfileCU1.ora'
ORA-02097: parameter cannot be modified because specified value is invalid
ORA-01565: error in identifying file '/opt/oracle/db11203/dbs/spfileCU1.ora'
ORA-27037: unable to obtain file status
HPUX-ia64 Error: 2: No such file or directory
With SPFILE I get;
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of Duplicate Db command at 10/01/2013 13:06:34
RMAN-05501: aborting duplication of target database
RMAN-05537: DUPLICATE without TARGET connection when auxiliary instance is started with spfile cannot use SPFILE clause
But I do have RMAN connexion to target database.
Thanks for your help.Here is the output beginning of the script which clearly shows that I'm always connected to target database:
Recovery Manager: Release 11.2.0.3.0 - Production on Tue Oct 1 13:05:47 2013
Copyright (c) 1982, 2011, Oracle and/or its affiliates. All rights reserved.
connected to target database: CU (DBID=1143962925)
connected to auxiliary database: CU (not mounted)
RMAN> set echo on
2> run
3> {
4> configure device type disk parallelism 10;
5> allocate channel pr1 type disk;
6> allocate channel pr2 type disk;
7> allocate channel pr3 type disk;
8> allocate channel pr4 type disk;
9> allocate channel pr5 type disk;
10> allocate channel pr6 type disk;
11> allocate channel pr7 type disk;
12> allocate channel pr8 type disk;
13> allocate channel pr9 type disk;
14> allocate channel pr10 type disk;
15> allocate auxiliary channel st1 type disk;
16> allocate auxiliary channel st2 type disk;
17> allocate auxiliary channel st3 type disk;
18> allocate auxiliary channel st4 type disk;
19> allocate auxiliary channel st5 type disk;
20> allocate auxiliary channel st6 type disk;
21> allocate auxiliary channel st7 type disk;
22> allocate auxiliary channel st8 type disk;
23> allocate auxiliary channel st9 type disk;
24> allocate auxiliary channel st10 type disk;
25> duplicate target database for standby from active database
26> spfile -
UCCX 8.0 SNMP notification to report failover from active to the standby server?
Does any know the UCCX 8.0 SNMP notification to report failover from active to the standby server? (The specific notification.)
ftp://ftp.cisco.com/pub/mibs/v2/CISCO-VOICE-APPS-MIB.my
I see this in the MIB.
cvaModuleStart NOTIFICATION-TYPE
OBJECTS { cvaAlarmSeverity, cvaModuleName }
STATUS current
DESCRIPTION
"A cvaModuleStart notification signifies that an
application module or subsystem has successfully
started and transitioned into in-service state.
This notification is working in conjunction with
the cvaModuleStop notification to notify the start
and stop status of a particular application module."
::= {ciscoVoiceAppsMIBNotifications 1}Attached are two files:
cad-ecc-viewer.html
This is a template HTML document which dictates how the pop up will look and what data fields are available.
cad-ecc-viewer.vbs
This is the Windows Scripting Host file which you run from a CDA workflow, and you pass it the values of the call data, it then launches an instance of IE and loads the above template.
By default the code is setup to use the following data from the call, but can be modified to work with more, less, or different data:
Customer Name
Customer Status (like Premium, or Platinum)
Customer Number (like an account number)
Customer Phone Number
So when you specify the VBS file to run in CDA you need to pass those variables in that order.
The CDA should expect the VBS file on the root of C:\ by default, and the VBS file expects the HTML Template on the root of C:\ also.
I have only tested this on UCCX 7x and IE 8x. Use the code as a guide to your own solution, that suites your business requirements.
EDIT: I see that this does not work on my Win7/IE9 system, so I will spend some time updating the code for Win7/IE9 and I'll let you know how it goes.
Anthony Holloway
Please use the star ratings to help drive great content to the top of searches. -
Duplicate database for standby from active database
I'm running 11.1.0.7. Has anybody ever duplicated a standby database from active database and the active database being a physical standby open for read only with active dataguard instead of a primary dataguard database?
The key here is location. The primary is located at a remote site where network bandwidth is inadequate for fast copy of database. The active standby database is at same site where I would like to build the new physical standby.I don't think you can, because "You cannot CONNECT RMAN to the standby database and then use DUPLICATE ... FOR STANDBY to create an additional standby database " and you can't fake it out by getting a controlfile from the primary because the controlfile has to match up with the backup and can't be a standby.
But I'm wondering if you could failover to the standby, duplicate, fail back, then... oh well, that will never work either, incarnation problem.
Snapshot standby? Could one back it up, then flashback restored new standby, change dbid? I would guess there would be an SCN problem, but don't know enough about it. -
I have ATV2 and the correct version of ITunes yet when watching a movie from ITunes, ATV2 will drop it mid way through and then will claim home sharing is not activated in ITunes. Can anyone offer advice please?
yepp, I have done numerous tests today, skipped router and hard wired betwenn PC and appletv3. same problem.
same network, but from my laptop, works like a charm.. so its not reproducable on all machines.
this seems to be a itunes/bonjour problem, not ATV3 problem. -
Duplicate target database for standby from active database session
i have 1 tb db. for example i execute the duplicate command from activate standby database.after 500gb datafile copy the session terminate due to some bottle neck ( network) .is it possible to resume the job again means job again starded from the previous stage .
thanks
Edited by: 913779 on Sep 4, 2012 12:28 AMHello;
Changing my answer - you can use repeat DUPLICATE to do this :
http://docs.oracle.com/cd/E11882_01/backup.112/e10642/rcmdupdb.htm#BGBEFJHH
As an alternative you could move the RMAN backup and then roll it forward :
http://www.visi.com/~mseberg/duprman2.html
and then :
http://www.oracle-ckpt.com/?s=incremental&op.x=0&op.y=0
Best Regards
mseberg
Edited by: mseberg on Sep 4, 2012 4:45 AM -
Audit DBA Activity, skip table from logical standby!
Dear All,
My database is 10gR2 on windows 2003 server.
I want to know if I can put some audit on the commands: execute dbms_logstdby.skip() to skip tables from Logical standby and also the same on unskipping the objects exec dbms_logstdby.unskip.
Thanks, ImranHi,
Given that your Database is 10g, the auditing options were extended to included DML from only SELECT in 9i, but not audit on procedures. You could double check the Fine Grained Auditing options in 10g, but I don't think this extends to DBMS_ packages.
I would consider writing a trigger or a small job that monitors the DBA_LOGSTDBY_SKIP view for additional entries. This is the only workaround that I can suggest that might fit your needs. -
Error during "duplicate target ... from active database"
hi:
RMAN duplicate failure after the auxiliary instance mounted,we want to create a physical standby database .
Platform: solaris10 spark 64bit
Version: 11.2.0.1.5 (both primary and standby)
thank you..
RMAN log:
rman target sys/password@his_primary auxiliary sys/password@his_standby_tt
Recovery Manager: Release 11.2.0.1.0 - Production on Thu Aug 30 15:40:06 2012
Copyright (c) 1982, 2009, Oracle and/or its affiliates. All rights reserved.
connected to target database: HIS (DBID=3271178181)
connected to auxiliary database: HIS (not mounted)
RMAN> duplicate target database for standby from active database;
Starting Duplicate Db at 30-AUG-12
using target database control file instead of recovery catalog
allocated channel: ORA_AUX_DISK_1
channel ORA_AUX_DISK_1: SID=2833 device type=DISK
allocated channel: ORA_AUX_DISK_2
channel ORA_AUX_DISK_2: SID=3399 device type=DISK
allocated channel: ORA_AUX_DISK_3
channel ORA_AUX_DISK_3: SID=3966 device type=DISK
allocated channel: ORA_AUX_DISK_4
channel ORA_AUX_DISK_4: SID=3 device type=DISK
contents of Memory Script:
backup as copy reuse
targetfile '/u01/oracle/product/11.2.0/db_1/dbs/orapwhis' auxiliary format
'/u01/app/oracle/product/11.2.0/db_1/dbs/orapwhis' ;
executing Memory Script
Starting backup at 30-AUG-12
allocated channel: ORA_DISK_1
channel ORA_DISK_1: SID=1570 device type=DISK
allocated channel: ORA_DISK_2
channel ORA_DISK_2: SID=1708 device type=DISK
allocated channel: ORA_DISK_3
channel ORA_DISK_3: SID=1851 device type=DISK
allocated channel: ORA_DISK_4
channel ORA_DISK_4: SID=1995 device type=DISK
Finished backup at 30-AUG-12
contents of Memory Script:
backup as copy current controlfile for standby auxiliary format '/u01/app/oradata/his/control01.ctl';
restore clone controlfile to '/u01/app/oradata/his/control02.ctl' from
'/u01/app/oradata/his/control01.ctl';
restore clone controlfile to '/u01/app/oradata/his/control03.ctl' from
'/u01/app/oradata/his/control01.ctl';
executing Memory Script
Starting backup at 30-AUG-12
using channel ORA_DISK_1
using channel ORA_DISK_2
using channel ORA_DISK_3
using channel ORA_DISK_4
channel ORA_DISK_1: starting datafile copy
copying standby control file
output file name=/export/home/oracle/snap.f tag=TAG20120830T154059 RECID=9 STAMP=792690060
channel ORA_DISK_1: datafile copy complete, elapsed time: 00:00:03
Finished backup at 30-AUG-12
Starting restore at 30-AUG-12
using channel ORA_AUX_DISK_1
using channel ORA_AUX_DISK_2
using channel ORA_AUX_DISK_3
using channel ORA_AUX_DISK_4
channel ORA_AUX_DISK_2: skipped, AUTOBACKUP already found
channel ORA_AUX_DISK_3: skipped, AUTOBACKUP already found
channel ORA_AUX_DISK_4: skipped, AUTOBACKUP already found
channel ORA_AUX_DISK_1: copied control file copy
Finished restore at 30-AUG-12
Starting restore at 30-AUG-12
using channel ORA_AUX_DISK_1
using channel ORA_AUX_DISK_2
using channel ORA_AUX_DISK_3
using channel ORA_AUX_DISK_4
channel ORA_AUX_DISK_2: skipped, AUTOBACKUP already found
channel ORA_AUX_DISK_3: skipped, AUTOBACKUP already found
channel ORA_AUX_DISK_4: skipped, AUTOBACKUP already found
channel ORA_AUX_DISK_1: copied control file copy
Finished restore at 30-AUG-12
contents of Memory Script:
sql clone 'alter database mount standby database';
executing Memory Script
sql statement: alter database mount standby database
contents of Memory Script:
set newname for tempfile 1 to
"/u01/app/oradata/his/temp.266.750421813";
set newname for tempfile 2 to
"/u01/app/oradata/his/ts_temp_patrol.298.750425277";
set newname for tempfile 3 to
"/u01/app/oradata/his/ts_his_temp.296.750427905";
set newname for tempfile 4 to
"/u01/app/oradata/his/ts_tjjk_temp.282.750427917";
set newname for tempfile 5 to
"/u01/app/oradata/his/ts_temp_shuhao.595.782919539";
switch clone tempfile all;
set newname for datafile 1 to
"/u01/app/oradata/his/system.256.750421615";
set newname for datafile 2 to
"/u01/app/oradata/his/sysaux.257.750421615";
set newname for datafile 3 to
"/u01/app/oradata/his/undotbs1.258.750421615";
set newname for datafile 4 to
"/u01/app/oradata/his/users.259.750421615";
set newname for datafile 5 to
"/u01/app/oradata/his/ts_his.280.750425023";
set newname for datafile 6 to
"/u01/app/oradata/his/ts_his_index.281.750425025";
set newname for datafile 7 to
"/u01/app/oradata/his/system.569.754307341";
set newname for datafile 8 to
"/u01/app/oradata/his/ts_bj.283.750425027";
set newname for datafile 9 to
"/u01/app/oradata/his/ts_gt.284.750425027";
set newname for datafile 10 to
"/u01/app/oradata/his/ts_fx.285.750425027";
set newname for datafile 11 to
"/u01/app/oradata/his/ts_uap.286.750425029";
set newname for datafile 12 to
"/u01/app/oradata/his/ts_gkxj.287.750425029";
set newname for datafile 13 to
"/u01/app/oradata/his/ts_xejj.288.750425031";
set newname for datafile 14 to
"/u01/app/oradata/his/ts_zdzyrz.289.750425031";
set newname for datafile 15 to
"/u01/app/oradata/his/ts_zj.290.750425033";
set newname for datafile 16 to
"/u01/app/oradata/his/ts_jgcp.291.750425033";
set newname for datafile 17 to
"/u01/app/oradata/his/ts_gtbj.292.750425033";
set newname for datafile 18 to
"/u01/app/oradata/his/ts_base.293.750425035";
set newname for datafile 19 to
"/u01/app/oradata/his/ts_exdata.294.750425035";
set newname for datafile 20 to
"/u01/app/oradata/his/ts_tjjk.295.750425037";
set newname for datafile 21 to
"/u01/app/oradata/his/ts_shuhao.594.782919537";
set newname for datafile 22 to
"/u01/app/oradata/his/ts_patrol.297.750425037";
backup as copy reuse
datafile 1 auxiliary format
"/u01/app/oradata/his/system.256.750421615" datafile
2 auxiliary format
"/u01/app/oradata/his/sysaux.257.750421615" datafile
3 auxiliary format
"/u01/app/oradata/his/undotbs1.258.750421615" datafile
4 auxiliary format
"/u01/app/oradata/his/users.259.750421615" datafile
5 auxiliary format
"/u01/app/oradata/his/ts_his.280.750425023" datafile
6 auxiliary format
"/u01/app/oradata/his/ts_his_index.281.750425025" datafile
7 auxiliary format
"/u01/app/oradata/his/system.569.754307341" datafile
8 auxiliary format
"/u01/app/oradata/his/ts_bj.283.750425027" datafile
9 auxiliary format
"/u01/app/oradata/his/ts_gt.284.750425027" datafile
10 auxiliary format
"/u01/app/oradata/his/ts_fx.285.750425027" datafile
11 auxiliary format
"/u01/app/oradata/his/ts_uap.286.750425029" datafile
12 auxiliary format
"/u01/app/oradata/his/ts_gkxj.287.750425029" datafile
13 auxiliary format
"/u01/app/oradata/his/ts_xejj.288.750425031" datafile
14 auxiliary format
"/u01/app/oradata/his/ts_zdzyrz.289.750425031" datafile
15 auxiliary format
"/u01/app/oradata/his/ts_zj.290.750425033" datafile
16 auxiliary format
"/u01/app/oradata/his/ts_jgcp.291.750425033" datafile
17 auxiliary format
"/u01/app/oradata/his/ts_gtbj.292.750425033" datafile
18 auxiliary format
"/u01/app/oradata/his/ts_base.293.750425035" datafile
19 auxiliary format
"/u01/app/oradata/his/ts_exdata.294.750425035" datafile
20 auxiliary format
"/u01/app/oradata/his/ts_tjjk.295.750425037" datafile
21 auxiliary format
"/u01/app/oradata/his/ts_shuhao.594.782919537" datafile
22 auxiliary format
"/u01/app/oradata/his/ts_patrol.297.750425037" ;
sql 'alter system archive log current';
executing Memory Script
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
renamed tempfile 1 to /u01/app/oradata/his/temp.266.750421813 in control file
renamed tempfile 2 to /u01/app/oradata/his/ts_temp_patrol.298.750425277 in control file
renamed tempfile 3 to /u01/app/oradata/his/ts_his_temp.296.750427905 in control file
renamed tempfile 4 to /u01/app/oradata/his/ts_tjjk_temp.282.750427917 in control file
renamed tempfile 5 to /u01/app/oradata/his/ts_temp_shuhao.595.782919539 in control file
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
executing command: SET NEWNAME
Starting backup at 30-AUG-12
using channel ORA_DISK_1
using channel ORA_DISK_2
using channel ORA_DISK_3
using channel ORA_DISK_4
channel ORA_DISK_1: starting datafile copy
input datafile file number=00008 name=+DATA/his/datafile/ts_bj.283.750425027
channel ORA_DISK_2: starting datafile copy
input datafile file number=00009 name=+DATA/his/datafile/ts_gt.284.750425027
channel ORA_DISK_3: starting datafile copy
input datafile file number=00005 name=+DATA/his/datafile/ts_his.280.750425023
channel ORA_DISK_4: starting datafile copy
input datafile file number=00015 name=+DATA/his/datafile/ts_zj.290.750425033
RMAN-03009: failure of backup command on ORA_DISK_3 channel at 08/30/2012 16:10:23
ORA-19558: error de-allocating device
ORA-19557: device error, device type: DISK, device name:
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-03135: connection lost contact
channel ORA_DISK_3 disabled, job failed on it will be run on another channel
RMAN-03009: failure of backup command on ORA_DISK_4 channel at 08/30/2012 16:42:19
ORA-19558: error de-allocating device
ORA-19557: device error, device type: DISK, device name:
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-03135: connection lost contact
channel ORA_DISK_4 disabled, job failed on it will be run on another channel
RMAN-03009: failure of backup command on ORA_DISK_2 channel at 08/30/2012 16:51:58
ORA-19558: error de-allocating device
ORA-19557: device error, device type: DISK, device name:
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-03135: connection lost contact
channel ORA_DISK_2 disabled, job failed on it will be run on another channel
RMAN-03009: failure of backup command on ORA_DISK_1 channel at 08/30/2012 17:49:09
ORA-19558: error de-allocating device
ORA-19557: device error, device type: DISK, device name:
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-03135: connection lost contact
channel ORA_DISK_1 disabled, job failed on it will be run on another channel
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of Duplicate Db command at 08/30/2012 17:49:09
RMAN-03015: error occurred in stored script Memory Script
RMAN-03009: failure of backup command on ORA_DISK_4 channel at 08/30/2012 16:42:19
ORA-19558: error de-allocating device
ORA-19557: device error, device type: DISK, device name:
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-03135: connection lost contact
RMAN-03009: failure of backup command on ORA_DISK_2 channel at 08/30/2012 16:51:58
ORA-19558: error de-allocating device
ORA-19557: device error, device type: DISK, device name:
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-03135: connection lost contact
RMAN-03009: failure of backup command on ORA_DISK_1 channel at 08/30/2012 17:49:09
ORA-19558: error de-allocating device
ORA-19557: device error, device type: DISK, device name:
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-03135: connection lost contact
RMAN-03009: failure of backup command on ORA_DISK_3 channel at 08/30/2012 16:10:23
ORA-19558: error de-allocating device
ORA-19557: device error, device type: DISK, device name:
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-17627: ORA-01041: internal error. hostdef extension doesn't exist
ORA-03135: connection lost contact
RMAN>
Primary database alert log:
Thu Aug 30 15:41:00 2012
Clearing standby activation ID 3277937203 (0xc3615a33)
The primary database controlfile was created using the
'MAXLOGFILES 16' clause.
There is space for up to 11 standby redo logfiles
Use the following SQL commands on the standby database to create
standby redo logfiles that match the primary database:
ALTER DATABASE ADD STANDBY LOGFILE 'srl1.f' SIZE 536870912;
ALTER DATABASE ADD STANDBY LOGFILE 'srl2.f' SIZE 536870912;
ALTER DATABASE ADD STANDBY LOGFILE 'srl3.f' SIZE 536870912;
ALTER DATABASE ADD STANDBY LOGFILE 'srl4.f' SIZE 536870912;
ALTER DATABASE ADD STANDBY LOGFILE 'srl5.f' SIZE 536870912;
ALTER DATABASE ADD STANDBY LOGFILE 'srl6.f' SIZE 536870912;
WARNING: OMF is enabled on this database. Creating a physical
standby controlfile, when OMF is enabled on the primary
database, requires manual RMAN intervention to resolve OMF
datafile pathnames.
NOTE: Please refer to the RMAN documentation for procedures
describing how to manually resolve OMF datafile pathnames.
Thu Aug 30 16:10:13 2012
Errors in file /u01/oracle/diag/rdbms/his_primary/his/trace/his_ora_25860.trc (incident=72361):
ORA-00600: internal error code, arguments: [1868], [0xFFFFFFFF7BBD4988], [], [], [], [], [], [], [], [], [], []
Incident details in: /u01/oracle/diag/rdbms/his_primary/his/incident/incdir_72361/his_ora_25860_i72361.trc
Thu Aug 30 16:10:20 2012
Trace dumping is performing id=[cdmp_20120830161020]
Thu Aug 30 16:10:22 2012
Sweep [inc][72361]: completed
Sweep [inc2][72361]: completed
Thu Aug 30 16:40:32 2012
Thread 1 cannot allocate new log, sequence 3031
Private strand flush not complete
Current log# 4 seq# 3030 mem# 0: +DATA/his_primary/onlinelog/group_4.579.759345057
Current log# 4 seq# 3030 mem# 1: /backup/odsdb/HIS_PRIMARY/onlinelog/o1_mf_4_74nf15rq_.log
Thread 1 advanced to log sequence 3031 (LGWR switch)
Current log# 5 seq# 3031 mem# 0: +DATA/his_primary/onlinelog/group_5.261.759345075
Current log# 5 seq# 3031 mem# 1: /backup/odsdb/HIS_PRIMARY/onlinelog/o1_mf_5_74nf1q2g_.log
Thu Aug 30 16:40:37 2012
LNS: Standby redo logfile selected for thread 1 sequence 3031 for destination LOG_ARCHIVE_DEST_2
Thu Aug 30 16:40:39 2012
Archived Log entry 5829 added for thread 1 sequence 3030 ID 0xffffffffc3615a33 dest 1:
Thu Aug 30 16:42:15 2012
Errors in file /u01/oracle/diag/rdbms/his_primary/his/trace/his_ora_25862.trc (incident=72369):
ORA-00600: internal error code, arguments: [1868], [0xFFFFFFFF7BBD4988], [], [], [], [], [], [], [], [], [], []
Incident details in: /u01/oracle/diag/rdbms/his_primary/his/incident/incdir_72369/his_ora_25862_i72369.trc
Thu Aug 30 16:42:17 2012
Trace dumping is performing id=[cdmp_20120830164217]
Thu Aug 30 16:42:17 2012
Sweep [inc][72369]: completed
Sweep [inc2][72369]: completed
Thu Aug 30 16:51:53 2012
Errors in file /u01/oracle/diag/rdbms/his_primary/his/trace/his_ora_25858.trc (incident=72353):
ORA-00600: internal error code, arguments: [1868], [0xFFFFFFFF7BBD4988], [], [], [], [], [], [], [], [], [], []
Incident details in: /u01/oracle/diag/rdbms/his_primary/his/incident/incdir_72353/his_ora_25858_i72353.trc
Thu Aug 30 16:51:55 2012
Sweep [inc][72353]: completed
Sweep [inc2][72353]: completed
Thu Aug 30 16:51:55 2012
Trace dumping is performing id=[cdmp_20120830165155]
Edited by: 960892 on 2012-9-24 上午2:22hi:
this is the initialization parameter file for auxiliary instance:
*.audit_file_dest='/u01/oracle/admin/his/adump'
*.audit_trail='db'
*.compatible='11.2.0.0.0'
*.control_files='/u01/app/oradata/his/control01.ctl','/u01/app/oradata/his/control02.ctl','/u01/app/oradata/his/control03.ctl'
*.db_block_size=8192
*.db_domain='abc.com.cn'
*.db_file_name_convert='+DATA/his/datafile/','/u01/app/oradata/his/','+DATA/his/tempfile/','/u01/app/oradata/his/','+DATA/his_primary/datafile/','/u01/app/oradata/his/','+DATA/his_primary/tempfile/','/u01/app/oradata/his/'
*.db_files=1000
*.db_name='his'
*.db_recovery_file_dest='/backup/oracle'
*.db_recovery_file_dest_size=1073741824000
*.db_unique_name='his_standby_tt'
*.diagnostic_dest='/u01/oracle'
*.dispatchers='(PROTOCOL=TCP) (SERVICE=hisXDB)'
*.fal_client='his_standby_tt'
*.fal_server='his_primary'
*.log_archive_config='DG_CONFIG=(his_primary,his_standby_tt)'
*.log_archive_dest_1='LOCATION=/backup/oracle/HIS_STANDBY_TT/archivelog VALID_FOR=(ALL_LOGFILES,ALL_ROLES) DB_UNIQUE_NAME=his_standby_tt'
*.log_archive_dest_2='SERVICE=his_primary LGWR ASYNC VALID_FOR=(ONLINE_LOGFILES,PRIMARY_ROLE) DB_UNIQUE_NAME=his_primary'
*.log_archive_dest_state_1='enable'
*.log_archive_dest_state_2='enable'
*.log_file_name_convert='+DATA/his_primary/onlinelog/','/u01/app/oradata/his/','/backup/odsdb/HIS_PRIMARY/onlinelog/','/u01/app/oradata/his/'
*.memory_target=2181038080
*.nls_language='SIMPLIFIED CHINESE'
*.nls_territory='CHINA'
*.open_cursors=300
*.processes=3000
*.remote_login_passwordfile='EXCLUSIVE'
*.service_names='his.abc.com.cn,his_standby_tt.abc.com.cn'
*.sessions=3305
*.standby_file_management='AUTO'
*.undo_tablespace='UNDOTBS1'
*.event='10298 trace name context forever, level 32' -
How reliable is DUPLICATE .. FROM ACTIVE DATABASE ?
Version : 11.2.0.3
Platform : OEL 6
DUPLICATE .. FOR STANDBY FROM ACTIVE DATABASE doesn't involve taking any RMAN Backup files. Right? Just transferring data across the network.
Given that I have a good network throughput, how reliable it is to use this feature to create a standby from a 2 TeraByte Primary ? The standby DB will be created in our Data Center located 50KM away from the Primary Site.Kavanagh wrote:
Version : 11.2.0.3
Platform : OEL 6
DUPLICATE .. FOR STANDBY FROM ACTIVE DATABASE doesn't involve taking any RMAN Backup files. Right? Just transferring data across the network.
Given that I have a good network throughput, how reliable it is to use this feature to create a standby from a 2 TeraByte Primary ? The standby DB will be created in our Data Center located 50KM away from the Primary Site.2TB is not a small database to perform Duplicate from ACTIVE Database, Yes as you said there is no more need of backups from 11g if you use ACTIVE database.
Do not consider of the distance, Consider the bandwidth speed between two sites and how fast data can transfer and how stable it is.
You can test the network speed by transferring any one of the big file using SCP also, On top of that you can estimate how much time it can complete and ensure there is no network glitches/interruptions to avoid failure duplicate. -
Duplicate from Active database
Hi,
I have RAC primary database running in 11.2.0.3 with linux 5(dc). We also have configured RAC cluster on DR site recently.Now we need to create stanby database on DR site.
For this is have following doubts
My database size is 6TB(from dba_segmnets) and total is 14TB(from dba_data_files)
1) How duplicate of active database works internally? Does it copy the exact file to standby site for example copy datafile(which is of 5GB in size) and send it over to standby over network?
2) Both primary and standby sites are in different states, so i was thinking to backup the primary database first to tapes and then courier tapes to dr site and then finally restore and recover standby.
I have doubts in above approaches which should i implement. I think active database duplication will skip a)backup time b) courier time. Is that correct?
However if my database size is 14TB and using 1st method, does it send files to dr worth of 14TB size?I am working on active database duplication and has below issue. Can any one help me on this?
RMAN> connect target sys@Pa305
connected to target database: PA305 (DBID=2787277616)
RMAN> connect auxiliary sys@Pb305
connected to auxiliary database: PB305 (not mounted)
RMAN> DUPLICATE TARGET DATABASE
TO 'PB305'
FROM ACTIVE DATABASE
2> 3> 4> ;
Starting Duplicate Db at 31-JUL-2012 17:20:07
using target database control file instead of recovery catalog
allocated channel: ORA_AUX_DISK_1
channel ORA_AUX_DISK_1: SID=2838 instance=PB3051 device type=DISK
contents of Memory Script:
sql clone "alter system set control_files =
''+DG_075_DATA01/PB305/controlfile/current.270.790104009'', ''+DG_075_FRA01/PB305/controlfile/current.286.790104009'' comment=
''Set by RMAN'' scope=spfile";
sql clone "alter system set db_name =
''PA305'' comment=
''Modified by RMAN duplicate'' scope=spfile";
sql clone "alter system set db_unique_name =
''PB305'' comment=
''Modified by RMAN duplicate'' scope=spfile";
shutdown clone immediate;
startup clone force nomount
backup as copy current controlfile auxiliary format '+DG_075_DATA01/PB305/controlfile/current.269.790104009';
restore clone controlfile to '+DG_075_FRA01/PB305/controlfile/current.288.790104009' from
'+DG_075_DATA01/PB305/controlfile/current.269.790104009';
sql clone "alter system set control_files =
''+DG_075_DATA01/PB305/controlfile/current.269.790104009'', ''+DG_075_FRA01/PB305/controlfile/current.288.790104009'' comment=
''Set by RMAN'' scope=spfile";
shutdown clone immediate;
startup clone nomount;
alter clone database mount;
executing Memory Script
sql statement: alter system set control_files = ''+DG_075_DATA01/PB305/controlfile/current.270.790104009'', ''+DG_075_FRA01/PB305/controlfile/current.286.790104009'' comment= ''Set by RMAN'' scope=spfile
sql statement: alter system set db_name = ''PA305'' comment= ''Modified by RMAN duplicate'' scope=spfile
sql statement: alter system set db_unique_name = ''PB305'' comment= ''Modified by RMAN duplicate'' scope=spfile
Oracle instance shut down
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of Duplicate Db command at 07/31/2012 17:20:18
RMAN-06174: not connected to auxiliary database
RMAN-03015: error occurred in stored script Memory Script
RMAN-04006: error from auxiliary database: ORA-12514: TNS:listener does not currently know of service requested in connect descriptor
RMAN>
Maybe you are looking for
-
Error while invoking DXFA to stitch templates
Hi, I am getting the following exception when I attempt to invoke DXFA to stitch multiple templates dynamically. The stitching works fine though. It is just the error message being printed that is annoying. I am using the JAR files from the Account E
-
Function Module or BAPI to update the cheque payments
Hi Everyone, I would like to know whether we have any Function Module or BAPI which can update the cheque payment or its attributes into SAP. Thanks, KC Message was edited by: kittu chowdary
-
I'm testing a computationally intensive java program that runs on several remote machines and its execution can last several days. From time to time, I'd like to check its progress to see if its doing the right thing by logging into one of the machin
-
Why in iMessage isn't there a vocal message?
My question is: Why isn't there a VOCAL MESSAGE? Apple must use it! Walter, italian
-
Why does Java utility look like this - mac god required pls
Where are my option tabs - this is driving me nutzoid