FX5200 causes XP blue screen

Hi,
Bought a MSI FX5200-TD128 card for my Compaq Evo D500 Desktop. The card was detected without issue. But after Windows login, XP abruptly terminates into a blue screen, indicating Page Fault Error caused by NTaccess.sys. Then, the PC after saving the coredump info, reboots itself.
Now I am running my PC in Safe Mode with Networking, and the display is standard VGA. I have downloaded the latest drivers for FX5200, but the problem still exists.
The Compaq BIOS information did not have many settings to play with. I tried setting the AGP aperture size to 256MB, but that did not help.
Hope someone can help me on this.
Rgds.

Thanks for the help. Driver Cleaner works. I think MSI live update may have caused the blue screen because at one point, after I removed the nVidia drivers and rebooted the machine, the blue screen still happened. So I uninstalled the MSI Utilities in Safe Mode and proceeded with installing the drivers from scratch.

Similar Messages

T61 DVD causes a blue screen crash

My T61 with a Mat**bleep**a DVD-RAM UJ-862 causes a blue screen crash when I put a blank, unformated disk in the drive. A pre-recorded video or audio disk will play but a blank disk causes a crash.

No it really doesn't "go to sleep." It doesn't seem to me to be "the monitor," I think this is strickly happening with the computer that incidentley happens to be connected to a monitor. My simple take anyway.

Blu-ray creation causes windows blue screen crash

I am testing Premier Elements 7 for the creation of best quality DVD and Blu ray disks. Source is AVCHD 1920x1080i and I have managed to create a number of DVD's and one Bluray without problem. My latest trial creating a Bluray disk failed at about 98%, burn in progress with a Device Error message. This resulted in a blue screen windows crash. Far more worrying is if I re-insert that BD RE disk back into my PC to erase it and try again, it immediately prompts a Blue screen windows crash, so I guess the disk is ruined. I have previously used Premiere Pro, Ulead and more recently Cyberlink Power Director and Sony Vegas. The quality of the DVD footage produced by Premier is far superior and the Bluray output was also excellent. Cyberlink has proved to be a good package appart from the poor quality of re-rendered output. Sony Vegas Pro seems the only one to recognise raw AVCHD footage and opt not to recompress it!!! The Movie Studio version doesn't appear to do this, however, I have only had a limited go at the trials. I had narrowed my choice to upgrading to Adobe Premier, or the cheaper Elements 7 which suits my requirements for home movies, however, a major windows crash, which I tend never to get has got me running scared. Why o why is there not a burn to hard disk option for Bluray creation as for DVD? Has anyone experienced a similar problem - any ideas as to what I could try?

A BSOD situation normally indicates something is wrong systemicly with the computer. It can be either software (usually OS), or hardware related.
The first thing that I would do would be to gather all info on your system and list full OS, version, updates, etc., and all hardware specs. Something in those lists might provide a clue.
Next, I'd look carefully at Event Viewer, especially at the System and Applications tabs. Look for yellow warning messages at the time of the BSOD, and especially the red error messages. It might be easier to invoke a BSOD, so you will know the exact time and date of the crash. Study each yellow and each red message carefully. Many might not yield much useful info, but some might tell you a lot of about what is happening, and may even give you the cause. Please explore every link that is offered in each of these messages. They should take you to either the MS site, or to the site of a software, or hardware company. These will likely be where you'll gather the most important data.
Here's what to look for in Event Viewer:
Give us any details found there.
Also, see this LINK. The video is a bit long, but will furnish you with a lot of troubleshooting tips, and also tools from MS. Make notes of these tools and their use.
Good luck,
Hunt

Firefox.exe is causing a blue screen of death in Windows Vista.

I was browsing the internet a few hours ago when my computer bluescreened. This is the first time this has ever happened on my 2-year-old system, so when Windows booted up again I searched for a way to diagnose the problem. The resulting Windows Debugging Tool cited Firefox.exe as the cause of the crash.
Has anybody else had this issue? Is there a solution?
Please and thanks! :-D

I have this problem for 3 weeks now.
Blue screen occurs 2/3 times a day, only when FF running (tested with IE : problem disapears).
More blue screens occur when playing a video, but happens without Flash player anyway.
Seems to be a minidump / AppDataLocal Temp... error.
Any idea ?

Blackberry Media Sync causes Windows "Blue Screen of Death"

I recently suffered a very inconvenient (and costly) "Blue Screen of Death" just after disconnecting my Pearl 8110 (using Media Sync. I run Windows XP).
I was wondering whether the Blackberry hardware or software had in some way caused this - and whether I should be concerned about using Media Sync in the future.
Any thoughts?

Who knows? It is possible. There are a couple of threads on here about this (although not Media Sync, just DTM). Check out this thread: http://supportforums.blackberry.com/t5/BlackBerry-Desktop-Software/Upgrade-of-Desktop-software-resul...
They mention they found a fix for the problem they were seeing on XP (SP2, not SP3).
I consistently get a system crash immediately on plugging in my BB. I am running 64-bit Vista SP2. I haven't found a solution, yet. And, I have a RAID drive, and have to suffer through a several hour image rebuild after the crash, so I understand "costly." At least I can still use the machine while it rebuilds.

Videos cause a blue screen in XP Pro

Hello all, I have been led to this site after hours of google searching and reading similar problems. the only thing I noticed is that most of the people having the same problem are from 2005 or 2007! The other thing I noted is the lack of any solution so I thought I should start a new thread myself...
Every time I try to import any video into my itunes (latest version) for my ipod nano (latest software update) I get, 90% of the time, an instant blue screen that references win32k.sys
I do not have any other program on my PC that will do this.
I have noted however some strange things about itunes in general.
I used a program called prism video converter, recommended to produce great ipod compatible video by a friend, I set it to convetrt about 6 video files, all to the exact same settings, same bitrate/size/etc and they came out fien.
I can even play them in windows mediaplayer no problem.
now, I open itunes and go 'import from folder' and select the folder they are all inside.
first try: Blue Screen.
Second try I did them one at a time through the add files way.
Wow! Video 01 appeared in itunes and no crash!
So I try adding the next one...
Itunes seemed to freeze a bit on doing this, maybe cos the video is a bit longer (only 3 minutes though) and then it displayed no change!
the first video was still there but it had not added the second.
I tried again with the second video.
Nothing appeared.
Why would this happen if the videos are technically the same??!
So I tried video 3.
It appeared in itunes!!
I tried video 4...
Blue Screen!
The worst of it is that usually, whatever I try I will get itunes throwing my PC into a blue screen error whenever I am dealing with these m4v, mp4 or mov (or any other apple video file!) and trying to put them into itunes.
I am so sick of this problem and I would not usually come and ask like this as I pride myself on using google etc and fixing my own PC problems but this one is just a bit too much asd there is no apparent logic to it and nothing I try gets me any closer to a solution!

**** there.
Let me first make this really clear: It is most definitely nothing to do with the Prism Software. I know this as I have tried converting with many programs before this but usually just got a bluescreen whatever I tried, as soon as I tried to import a video file into itunes.
the thing about prism is that this seems to be the only time I have actually managed to succeed in importing a video file into itunes! So if anything it is faring better than anything else!!
I am usually really good with video on a PC. I have created and encoded and converted so many in the past that I am usually able to work it out if there's maybe a compatibility issue or a codec issue. This time ... nope!
I do think it may be related to some codec or the way XP is handling these itunes compatible video files. They seem to just cause errors.
Ironic: I just dragged and dropped one of the video file sinto a quicktime window and I got a bluescreen.(Thank god for firefox session manager, saving what I had typed so far).
Anyway the result is that these files are also able to throw the same blue screen if I drag them into firefox.
I have converted to ipod format from many apps and, whatever app I use, whatever bitrate I use, if it is a file format as described above (Ie. the type it has to be to play in itunes/ipod) then it will/can/usually does give this blue screen!
Please be clear though: Prism has nothing to do with it. Also, I am confused what the criteria is for itunes to accept video files anyway...why is it that it will accept some and not others that are in essence, exactly the same?
Any help is greatly appreciated

When watching Youtube clips firefox causes windown blue screen - windows 7 on HP8540w

Hi
HP8540w laptop with Windows7 professional.
when watching youtube clips windows crashes - blue screen of death!
watching the same clips in Internet explorer doesn't cause a crash - isolated to Firefox.

See below -- the way I asked the question the first time may not be clear. This post was a goof but I can't figure out how to delete it

Sound Blaster Zx driver install causes IO blue screen

So things went like this:
I received my Sound Blaster Zx today. Opened it up, found that it contained some very handy instructions, so I followed those to the letter.
During the installation of the drivers, after I was prompted to choose whether or not to install the drivers by my Windows 7 64 bit (which obviously I chose to install), it blue screened with an IO error.
Then, presumably because the drivers didn't install correctly, it blue screened due to cthdb.sys every time I booted up.
I had to boot in safe mode and remove the drivers.
Then, I started up normally again. Windows automatically installed the drivers, even though it is said to do NOTHING when it detects a new device - no updates, no driver installation, no nothing. It installed the SAME drivers and so I had the IO blue screen again, and then blue screened due to cthdb.sys every time I booted.
Again I had to remove the drivers using safe mode.
No drivers will install without the card being installed, and if the card installed then the dodgy, BSOD causing drivers get installed automatically.
What do I do?

Uninstall the sound driver via Device Manager and remove when asked all the drivers related so it doesnt reinstall them at every reboot.
Swap the card around until you find a good slot and uninstall drivers and disable in BIOS afterwards the onboard prior testing another driver.
Is the cards properly seated in the slot ?!
Ignore the metal stuff look at the slot.

NEO2-FIS2R ATI 9800 AIW Pro TV Tuner causes freezes/blue screens. Help!

I recently upgraded my system from P4 2.4Ghz to P4 3.4Ghz Northwood and went from All in Wonder Radeon to 9800 AIW Pro. Only other change worth mentioning is I created a 0+1 RAID using 4 hard drives which were previously configured differently. I watch a lot of TV while I work on the computer. I do a lot of disk writes and data management which ultimately creates a lot of transfering of data between disks. Never was a problem in the old config. BTW, I also use an external HD conntected through USB for data transfers as well.
Immediately, my system went from stable to unstable. I first noticed that the destop redraw on bootup was slower. Then I noticed that the TV had a delayed response on changing channels and changing volume. Switching to another window causes a slow redraw and sometimes causes a jerk in the TV display like a hickup. Other symptoms include blue screens but no driver is referenced. The blue screen otherwise is a normal STOP screen except for the bottom quarter of the monitor which looks like video garble. Sometimes it just reboots. Sometimes, it freezes. I noticed that doing disk transfers while watching TV usually speeds up the behavior. Comparatively, my use of the TV in the old config was transparent regarless of how much I taxed the system.
Anyway, in view of the unexpected behavior, I decided to backup and reinstall the OS from scratch using a vanilla install method. Everything was detected properly, OS installed fine. Installed ATI's latest Catalyst drivers. I turn on the TV and within about 15 minutes of use, the erratic behavior begins. I figured it was a bad card so I exchanged it out. Same thing with the new card. ATI is shrugging their shoulders and pointing at MSI.
I ran hardware tests, updated the MB BIOS to latest available. Tested all four hard drives/RAM. I can't find any hardware issues. I'm very conservative with my BIOS settings so aside from the default values, I have only changed the settings required to allow for a 0+1 RAID config on the Promise controller.
I put my old ATI Radeon back in and ran the TV for hours and had no problems at all. I also swapped my old 2.4 back in with the 9800 AIW Pro and the problem is recreated so that is what has me ruling out the processor.
Here's what the box looks like inside.
Antec 480 True Blue
MSI NEO2-FIS2R (w/latest BIOS)
1GB Corsair VS512MB400 x 2
4 Maxtor 160GB hard drives, 8MB Cache, 2ea SATA, 2ea PATA
Intel 3.4Ghz Northwood CPU, 512KB, 800FSB w/Zalman 7700CU HS/F
ATI 9800 AIW Pro 128MB DDR
Front/Rear 120mm Case Fans
Optical drive, floppy drive, modem card, sound card.
NOTE: All USB ports are being used by devices with their own power supply except for a web camera. All fans are using power from PSU. No fans use MB power.
I also checked to insure that the AGP card was seated correctly and verified that it was. So, I'm pretty bummed out that I just dropped circa $500 on improving my system but I can't even get it work as well as it used to.
I think I have found the problem but short of getting rid of the 9800 AIW Pro, I am hoping that someone else has had this problem and can help me out. Your ideas would be greatly appreciated!!!

Good News!!
While the DDR voltage was set to 2.7, I recreated the conditions in which the failures tended to occur. Within minutes, it was obvious that something had changed as I had never gone that far without getting kicked out, freezing up, or blue screening. Since this is looking more and more like a power issue, I decided to leave all of my external USB connections disconnected except for the external hard drive because I normally transfer data back and forth frequently from it.
When I saw that the system was holding up well, I connected the rest of the USB connections. Everything ran OK for a few minutes but then the sound from the TV dropped out while the picture continued to function. Although, this marked another failure, it was a marked improvement over what had been happening previously.
NovJoe suggested tweaking the voltage to 2.7 ~ 2.8 so I upped the voltage to 2.8 and setup the same environment and the machine has run that way for about 3 hours. That one increment seems to have made a difference.
Questions which come to mind.
1. If this is a power issue, is it the motherboard's inability to supply the correct voltage to the motherboard components or is it a PSU issue which isn't providing the motherboard enough juice to do its job or a combination of both?
2. If this issue can be corrected through tweaking voltages, how do you know how far to go before damaging system components?
One of the original symptoms with the TV is still apparent. Upon changing channels, there is a second delay before the sound and picture synchronize. Changing foreground windows also causes a "hickup" in the TV's sound/video. I'm more concerned with what this behavior may mean from a system performance standpoint rather than the annoyance since this is a 9800 AIW Pro and it should be snappy instead of sluggish.
Up the AGP voltage? On that subject, the people here seem to have a lot of background with tweaking the BIOS. I'd appreciate any other ideas in tweaking this system as well.
Ultimately, I have to answer the question of whether I need to get a bigger PSU or can I safely correct my system performance by using BIOS tweaks?
Thanks again for all your help.

Firefox is causing my computer to crash. It is causing the blue screen of death. What can I do to solve this problem?

Mozilla firefox is crashing my computer. It will run and the blue screen would come on because of this I cannot run firefox on my computer anymore. What to do?
== This happened ==
Every time Firefox opened
== June 2010 ==
== User Agent ==
Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.0; Trident/4.0; SLCC1; .NET CLR 2.0.50727; Media Center PC 5.0; InfoPath.2; .NET CLR 3.5.30729; .NET CLR 3.0.30729; OfficeLiveConnector.1.5; OfficeLivePatch.1.3; .NET4.0C)

Firefox doesn't do email, it's a web browser.
If you are using Firefox to access your mail, you are using "web-mail". You need to seek support from your service provider or a forum for that service.
If your problem is with Mozilla Thunderbird, see this forum for support.
[http://www.mozillamessaging.com/en-US/support/]
or this one
[http://forums.mozillazine.org/viewforum.php?f=39]

Deskjet 6940 causing a blue screen and rebooting PC on bootup

I have a strange problem with a clients PC. Whenever it boots up, if the Deskjet 6940 is connected via a usb cable it blue screens and reboots. The PC was recently updated to Service Pack 3, at first I thought the amount of memory was too low (248 mb, with 8 shared with video). So I upgraded the memory to 1 Gb but it still happens, if the printer is not plugged in it goes into Windows and works fine. if I then plug the printer in it reboots immediately.
I've tried different USB sockets, I've tried uninstalling the drivers and all the HP software, rebooting and downloading the latest drivers from HP. This seemed to cure it for a few hours, but later that same day the client called me again to say it had rebooted again.
I have spoken to HP support in the UK and was told that HP have issues with Service Pack 3 of XP. I found this hard to believe and also embarrassing - this is a new IT support contract and I recommended that all the PC's were upgraded to SP3.
Gareth Davies

I would suggest you upgrade teh drivers for your motherboard and also update the BIOS of your motherboard too and see if that resolves the issue.
Make it easier for other people to find solutions, by marking my answer with \'Accept as Solution\' if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"
I am an ex-HP Employee.

What causes repeated blue screens? Can I fix this?

Pavillion P7-1036 Windows 7 64 Bit Blue screens repeatedly, almost daily since PC was purchased and brought home.
Error message: Blue screen with "Windows has detected.... and shut down to protect your computer....if this is the first time....etc, etc, then long lines of 0's X's F's too long to copy down. Hours spent on telephone with HP Support.
This question was solved.
View Solution.

Hi,
Have you tried a full HP Recovery? Backup you data to external media before doing so. After you do the full recovery, do not let the Microsoft autoupdate process apply any updates until you can determine if your PC is stable. There might be a bad MS update.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Usb 6501 unresponsive causing BSOD(Blue Screen Error)

There are a lot posts about the same issue but mine is a little peculiar so i decided to post it.
I am using two usb DAQ in the same pc(usb-6501, usb-6001), connected to the usb port on the back. The usb-6501 is used to obtain digital inputs from read switches, Sensors through an ssr. The usb-6001 is used to control 2 double valve solenoid, 1 dc motor, 2 indicator lamps. usb-6001 is also used to read analog values of current(using hall effect sensor) and voltage(using potentiometer).
At first i was facing problems with the usb-6001(the usb-6501 was working fine at this point) resetting during operation accompanied by BSOD. Then i learned it was due to my relay, which requires 30 mA of current to switch so i used the ULN2003a to interface the usb-6001 with the relays and after that the application was running perfectly for 4 days.
Now the usb-6501 is having the same problem and when i perform "Self Test" from NI MAX it shows "Error Code:50405" and i am able to reset the device from NI MAX only sometimes, other times i would have to unplug the USB device then plug it back in. As the application is used for an automated test rig the customer is frustrated by this problem. Once the card becomes unresponsive(or after the card is reset) BSOD occours.
I have checked all the device drivers and OS for any errors but they are fine. i have even tried changing the ram to solve the BSOD with no use.
System Details:
Windows 7 SP1
NI MAX 14.0
power saving is disabled
I have attached the latest mini dump files as they might help in finding out the reason behind this problem(File extensions changed for the purpouse of uploading).
I need to know: Is there any permanent solution for this problem? and what is the reason for this problem.
Attachments:
060115-12480-01.txt ‏315 KB
053015-12324-01.txt ‏315 KB
052615-17440-01.txt ‏315 KB

Additional info : i did an analysis of the dump files and this is the result
0: kd> !analyze -v
* Bugcheck Analysis *
DRIVER_IRQL_NOT_LESS_OR_EQUAL (d1)
An attempt was made to access a pageable (or completely invalid) address at an
interrupt request level (IRQL) that is too high. This is usually
caused by drivers using improper addresses.
If kernel debugger is available get stack backtrace.
Arguments:
Arg1: fffff88009fe10b1, memory referenced
Arg2: 0000000000000002, IRQL
Arg3: 0000000000000000, value 0 = read operation, 1 = write operation
Arg4: fffff8800657922e, address which referenced memory
Debugging Details:
READ_ADDRESS: GetPointerFromAddress: unable to read from fffff800032c30e8
fffff88009fe10b1
CURRENT_IRQL: 2
FAULTING_IP:
nifslk+822e
fffff880`0657922e 0fb650ff movzx edx,byte ptr [rax-1]
CUSTOMER_CRASH_COUNT: 1
DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT
BUGCHECK_STR: 0xD1
PROCESS_NAME: System
TRAP_FRAME: fffff80000b9c6b0 -- (.trap 0xfffff80000b9c6b0)
NOTE: The trap frame does not contain all registers.
Some register values may be zeroed or incorrect.
rax=fffff88009fe10b2 rbx=0000000000000000 rcx=0000000000000000
rdx=fffff80000b9c8e0 rsi=0000000000000000 rdi=0000000000000000
rip=fffff8800657922e rsp=fffff80000b9c840 rbp=fffff88009fe10b1
r8=0000000000000000 r9=0000000000000000 r10=0000000000000000
r11=0000000000000000 r12=0000000000000000 r13=0000000000000000
r14=0000000000000000 r15=0000000000000000
iopl=0 nv up ei ng nz na po nc
nifslk+0x822e:
fffff880`0657922e 0fb650ff movzx edx,byte ptr [rax-1] ds:c8e0:fffff880`09fe10b1=??
Resetting default scope
LAST_CONTROL_TRANSFER: from fffff80003091be9 to fffff80003092640
STACK_TEXT:
fffff800`00b9c568 fffff800`03091be9 : 00000000`0000000a fffff880`09fe10b1 00000000`00000002 00000000`00000000 : nt!KeBugCheckEx
fffff800`00b9c570 fffff800`03090860 : fffffa80`06adc250 fffffa80`05c3a060 fffffa80`06adc250 00000000`0000ffff : nt!KiBugCheckDispatch+0x69
fffff800`00b9c6b0 fffff880`0657922e : fffff880`05d47468 fffff880`01d91f90 00000000`00000000 fffff880`09fe0770 : nt!KiPageFault+0x260
fffff800`00b9c840 fffff880`05d47468 : fffff880`01d91f90 00000000`00000000 fffff880`09fe0770 fffff880`09fe17a0 : nifslk+0x822e
fffff800`00b9c848 fffff880`01d91f90 : 00000000`00000000 fffff880`09fe0770 fffff880`09fe17a0 fffff880`09fe10b1 : 0xfffff880`05d47468
fffff800`00b9c850 00000000`00000000 : fffff880`09fe0770 fffff880`09fe17a0 fffff880`09fe10b1 fffff800`00b9c8e0 : nipalk+0x75f90
STACK_COMMAND: kb
FOLLOWUP_IP:
nifslk+822e
fffff880`0657922e 0fb650ff movzx edx,byte ptr [rax-1]
SYMBOL_STACK_INDEX: 3
SYMBOL_NAME: nifslk+822e
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: nifslk
IMAGE_NAME: nifslk.dll
DEBUG_FLR_IMAGE_TIMESTAMP: 51f2daeb
FAILURE_BUCKET_ID: X64_0xD1_nifslk+822e
BUCKET_ID: X64_0xD1_nifslk+822e
Can anyone help me with what this means?

Deskjet F4280 causes constent blue screen errors

The moment I installed the printer the printer the errors started. Uninstalled the printer for 4 days, not a single error. I Can't keep the printer installed. What a waste of money!

you've done well

I tune causeing blue screen

Whenever I open Itunes it causes a blue screen with the error saying somthing about paged in a nonpaged area there is really nothing else to go on then that.

hi Redlion!
just doublechecking. is that an "0x00000050: PAGEFAULT_IN_NONPAGEDAREA" that you're getting, or are you getting different numerical and/or text codes with your blue screen?
if you're not sure, rather than provoking another blue screen maybe this reference might help jog your memory:
Troubleshooting Windows Stop Messages
keep us posted.
love, b

FX5200 causes XP blue screen

Similar Messages

Maybe you are looking for