FX8320 with MSI 760GA-P43 (FX) MS-7699 drop speed on high load

I had an FX8320 with watercooling on this MS-7699 motherboard, when with high load the CPU (all 8 cores) drop to 1.4Ghz then come back to the normal frequency within a few seconds, is there anyway to maintain the cpu speed at all time with high load?

No there isn't. The board is not able to cope with the power draw of an FX83xx cpu. Sadly MSI for some time listed FX 8-core cpus supported on all 760G product sites despite these are only able to run 95W TDP cpus at the very maximum. The behavior you are experiencing is a cheap trick to make the cpu seem supported while the only way to keep the board from burning up is to throttle the cpu under load. To run the cpu at full performance you need a new board meant for supporting 125w+ cpus.

Similar Messages

Msi 760ga-p43 crashes on wake from S3 sleep

Hello,
I have the msi 760GA-P43 motherboard with Windows 8.1 installed on a 250gb Samsung 840 Evo SSD, and I'm unable to get the computer to wake up from sleep in S3 mode without Windows crashing a few seconds after wakeup. I also can't wake up from keyboard or USB mouse (can only wake from power button). When it does wake up and crash, the system restarts itself and then returns to Windows as if waking from hibernated state - i.e. all programs still running.
Sleep works in S1 mode, but in S1 mode the fans don't stop so this seems kind of pointless. I have played around with various power settings within Windows but nothing makes a difference. Tried setting 'boot from PS/2' and 'boot from USB device' to Enabled in BIOS, no success.
I have a Phenom II X6 1055T CPU @125W, 8gb of 1333MHz RAM. Any advice very welcome, thanks in advance.

A couple more details:
I have hybrid sleep disabled in Windows.
I get the same result whether the Wakeup Event (in BIOS) is set to BIOS or OS.
BIOS is updated to most recent, ver 1.2

MSI 760GA-P43 (FX) supports windows 8.1?

Hello,
I am building desktop pc with a msi 760GA-P43 (FX) and an amd fx-4300.
My os is going to be a windows 8.1.This os is going to be a problem in my setup?In the drivers,the bios,the hardware(hdd,sdd,gpu) or anything else?

I would recommend W7 as the only W8.1/8 drivers MSI has for that MB is for ASMEDIA SATA and no others. Personaly I would not use W8.1/8 for anything.

Motherboard MSI 760GA-P43

Hi
I buy this Motherboard: MSI 760GA-P43 and have some problems.
Motherboard problems:
Computer won't start when i press a keyboard/mouse button
No power on USB /PS2 slots when pc is shutdown.
I try S3 and S1 configuration but still nothing.

see this guide: https://forum-en.msi.com/faq/article/wake-on-lan

Msi 760ga-p43 fx

Good afternoon.
Recently bought a ssd drive, Plextor m5 pro.
Included in the 6gb port, but the rate has not risen above 200.
In normal sata II, speed 260/220.
Drivers are installed on Asmedia, how to get out of the situation?
How do I get sata III ports?
I beg your help, thank you

Hi
You cant get more speed probably due to the Northbridge/ southbridge PCIe link speed limitation, its linked at 1xPCIe v1.1 250MB/s.
http://en.wikipedia.org/wiki/AMD_700_chipset_series#760G
I think that's the case and its common but, i done some testing with my own system and the results are like that but only limited to PCIe v2.0 500MB/s.
https://forum-en.msi.com/index.php?topic=170128.msg1242754#msg1242754
Anyway you should ask to MSI technical support just to be sure.
Edit: What bios version have the motherboard?
Now there is Bios v 1.1 that upgrades PCIEx (4 slot) to PCIe Gen2, the Asmedia controller most probably be exclusive but if its shared with PCIe 4 slot you should get better speeds with the Bios update.

MOVED: Motherboard MSI 760GA-P43

This topic has been moved to MSI AMD boards.
https://forum-en.msi.com/index.php?topic=179155.0

see this guide: https://forum-en.msi.com/faq/article/wake-on-lan

Does 760ga-p43 (fx) supports port multiplier for sata?

1) I have a 760ga-p43 (fx) and I couldn`t find anywhere if it supports port multiplier for sata.
Does someone have any idea?
2) I tried a delock 70146 and I couldn`t make it see also the sata on motherboards and the sata on the pci card. For lack of information on that msi "user guide" I tried any combination on AHCI, ide and sata, but it was a blind trying. It would be great a little help on what to look for.
Thanks,
Radu

what exactly do not works properly?
list full system specifications, see >>Posting Guide<<

Recent Conversation with MSI and Neo4 overclocking "thing"

I had a recent email transaction with MSI if anyone is interested. I tried my best to represent the group, and I know we all experience the problem a little bit different which is why it has been hard to explain and fix. I tried to give them the best info to duplicate the issue in the lab. It seems clear at this point that MSI still isn't duplicating the issue. They are using 166 Mem Clock Index, and the HT freq of 3x and still not understanding the issue, hopefully I have gave them a guide to duplicate what we have been trying to say. Yes I have explained this to MSI before but I really feel I am getting somewhere with my last 2 emails. Once we get them to duplicate the results then I think we will all have our solution shortly. Before anyone says anything negative, at least they aren't saying, oh that's an overclocking problem we don't deal with that. Also remember how long it has taken to get many people to see the issue, this isn't easy to understand so just stay cool, don't say negative sh-t if you reply and we'll see how this pans out. It was actully kind of hard since I am sitting in a hotel room 500 miles away from the motherboard but I was able to use modbin6 to view the BIOS and since I have done this about 7 zillion times I remember the settings LMAO. They have their Venice to 2750, not bad...
Hello MSI Engineer,
The information you requested. The data you sent shows a Venice running at 166 Memclock index value at HT at 3x, the goal is to run at 200 Memclock Index and HT at 4x. In order to duplicate this issue in the lab here is my recommendation. It MUST be tried with a CBBID Winchester RevD CPU and a Venice Rev E CPU and the Gskill memory you have in dual channel. The issue happens everytime with a CBBID Winchester and less often with Venice.
Starting with the Venice 3500+, Set the following in BIOS
[Memclock Index] 200
[CAS# latency (Tcl)] 3
[Min RAS active] 11
[RAS to CAS delay] 6
[Row Precharge] 6
[User config mode] manual
[bottom of 32 bit] (default)
[1T/2T] 1T
[Read Preamble] 6ns (default)
[Async Latency] 6ns (default)
[S/W mem hole] Disable (default)
[H/W mem hole] Disable (default)
[MTRR mapping] Continuous (default)
[High Performance] manual
[Agreessive timing] Disable
[Dynamic Overclocking] Disable
[Adjust CPU FSB Frequency] 200
[HT Frequncy] 4
[HT Width] 16 up 16 down
[CPU Spread] Disable
[SATA Spread] Disable
[PCI Spread] Disable
[PCIe Clock] 101
[SSE/SSE2] Enable
[CnQ] Disable
[CPU Ratio] 11x
[Adjust CPU VID] 1.45
[Extra CPU Voltage] your choice for stability
[Mem Volt] your choice for stability
[NF4 Volt] your choice for stability
Now boot into Windows. Using Clockgen, increase HTT to 250. This should be stable based on your screen shot and your RAM modules. Now having a CPU 2750Mhz, RAM at 250Mhz, and a HT of 4x250(1000). Test for stablity with Prime95 or other Stress Testing tool. Now we can say motherboard is stable at 2750Mhz CPU, 250Mhz RAM, and HT 4x250(1000). Now return to the BIOS at set the following
[Adjust CPU FSB Frequency] 250
This reults in a no POST condition for me and others. Now install the CBBID, except you will have to set a lower CPU max speed based on CBBID overclocking potential. In the BIOS, Return [Adjust CPU FSB frequency] to 200, Perhaps [CPU ratio] of 10x or 9x but a [Memory Clock Index] 200Mhz. Boot to Windows and use Clockgen to raise HTT to 250 again. Once you find a [CPU Ratio] that will have a STABLE overclock with a 250HTT. Return to the BIOS and set [Adjust CPU FSB Frequency] to 250. Try and POST. Try this experiment with the 3.1, 3.3, and 3.4 BIOS's. For the CBBID and the 3.1 BIOS you should be able to change the [HT Freq] to 3x, 2x or 1x and get a POST with [FSB Freq] 250, [Memclock Index] 200, and a known stable [CPU Ratio] you found in Windows. The 3.3, and 3.4 BIOS have made this work around not possible. Why does [HT Freq] 4x work in windows but not at POST time?
As a side note. The 1.3 BIOS for the 7125 works with the Venice, and the 1.4 and 1.5 do NOT. So somewhere between the 1.3 and 1.4 MSI created the issue on the Venice. Perhaps that is where you can find the answer and solution to the problem.
Here are some articles that describe the issue on a ECS and Chaintech board that were remidied by a BIOS update. So the problem is not uncommon and should be able to be fixed.
http://www.xbitlabs.com/articles/mainboards/display/chaintech-nforce4_6.html
http://www.xbitlabs.com/articles/mainboards/display/ecs-kn1-extreme_9.html
Here is some other users data of NF4 SLI and Ultra MSI Neo4's if you want to see some other BIOS settings.
https://forum-en.msi.com/index.php?topic=81364.0
Here is a screen shot of my Neo4 Plat SLI (MS-7100) 3.1 BIOS and CBBID Winchester(The Venice will NOT POST at all above [Adj CPU Freq] ~219-229 under any situation but is stable in Windows at HTT 250 with Clockgen). The system is stable and POST's when [HT Freq] is 3x, it will NOT at [HT freq] 4x which is stable in windows but won't POST.
http://home.comcast.net/~aicjofs/cbbidMSI2501.jpg
Here is another screenshot of the Asus A8N Plat SLI with all peripherals the same. Only changed the motherboard. This is POSTing at [HT Freq] 4x. This is just as a reference that the components do indeed POST with [Adjust FSB freq] 250, [Memclock Index] 200, and [HT Freq] 4x. This board will POST both my 3200+ Venice and Winchester CBBID at the settings described above.
http://home.comcast.net/~aicjofs/cbbid250asus1.jpg
The following are my BIOS settings that will create a non-POST condition, but the board is stable at these settings when ADJUSTED FROM WINDOWS.
[ADVANCED BIOS]
[Gate A20] Enable
[APIC] Enable
[MPS Table] 1.4
[Boot OS2] No
[ADVANCED CHIPSET]
[System BIOS Cacheable] Disabled
for newer BIOS
[SLI Brodcast apeture] Whatever default is.
[INTEGRATE PERIPHERALS]
[Onboard IDE 0 and 1] Enabled all channels in Auto
[IDE DMA] Enabled
[SATA 1,2,3,4] Enabled
[IDE PREFETCH] Enabled
[NVDA RAID] Enabled
[all IDE raid channels] Disabled
[all SATA raid channels] Enabled
[On Chip USB] 1.1-2.0
[USB KB/Storage] Disabled
[NVDA LAN] Enabled
[NVDA ROM] Disabled
[Onboard VIA 1394] Enabled
[Marvell Gigabit] Disabled
[Onboard Creative] Enabled
[SiI3132] Disabled
[FDC] Enable
[Serial Ports] Disabled
[Parallel Port] Disabled
[POWER MANAGMENT] all defaults
[PNP/PCI]
[Init display] PCIe
[Resources] Auto
[PCI Express Max Payload] 4096
[CELL MENU]
[Timing mode] manual
[Memclock index value(MHz)] 200
[CAS# latency (Tcl)] 3
[Min RAS active] 8
[RAS to CAS delay] 4
[Row Precharge] 4
[Row cycle time] Auto
[Row refresh] Auto
[Row to Row delay] Auto
[Write Recovery] Auto
[Write to Read] Auto changing this to known working value will lock system sometimes
[Read to Write] Auto changing this to known working value will lock system sometimes
[Refresh] Auto
[User config mode] manual
[bottom of 32 bit] whatever it defaults to
[1T/2T] 1T
[Read Preamble] 6ns
[Async Latency] 6ns Attempts to change this to 8ns will lock system
[S/W mem hole] Disable
[H/W mem hole] Disable
[MTRR mapping] Continuous
[High Performance] manual
[Agreessive timing] Disable
[Dynamic Overclocking] Disable
[Adjust CPU FSB Frequency] 250
[HT Frequncy] 4 (For 1000Mhz)
[HT Width] 16 up 16 down
[CPU Spread] Disable
[SATA Spread] Disable
[PCI Spread] Disable
[PCIe Clock] 101
[SSE/SSE2] Enable
[CnQ] Disable
[CPU Ratio] 10x
[Adjust CPU VID] 1.45
[Extra CPU Voltage] +9.9%
[Mem Volt] 2.7v
[NF4 Volt] 1.65v
BIOS Tested 3.0, 3.1, 3.2, 3.3, 3.4. I have not tested 3.51 but forum users are still not getting positive results
-------------- Original message --------------
Dear Aicjofs
This is MSI technical support engineer from Taiwan.
We receive some message from MSI LA office & Anandtech.com.
We are sorry for inconvinence experience when you try to Overclock MS-7100.
We hope to contact with you directly and help you to solve it.
Depends on related message from others, we know that you have several problem for MS-7100 overclocking.
According to your info at MSI Forum, Here is your system configuration:
Neo4 Plat SLI(MS-7100) 3.1 BIOS
3200+ Venice (8x313) @ 2500Mhz
Patriot PC4000 (200:133) 2.5-3-3-7
HT x3
Aopen 6800GT @ Ultra speed
AthenaPower 500W 3.3v - 26a 5v - 47a 12v - 28a
Could you give us more info about what changed item inside your BIOS?
[Memclock index value(MHz)]
[CAS# latency (Tcl)]
[Adjust CPU FSB Frequency]
[HT Frequncy]
[Adjust CPU VID]
[Extra CPU Voltage]¡Kor others
We try to Overclock MS-7100 with BIOS v3.2 and 3500+ (Venice core).
CPU ADA3500DAA4BW ABBWE made in Malaysia
Memory G-skill PC4400 512MB*2 (Dual Channel)
We only change some item inside BIOS as: (Based on Optimized defaults)
[Memclock index value (MHz)] à166
[CAS# latency (Tcl)] à 3
[Adjust CPU FSB Frequency] à250
[HT Frequncy] à3x
[Adjust CPU VID] à 1.450V
[Extra CPU Voltage] àOver VID 6.6%
We will try to find similar CPU as yours to test it.
If possible, please tell us the CPU OPN number like we listed. (ADA3500DAA4BW)
We also help to know any other info that you can provide.
If possible, please help to tell us more setting and system info.
Thanks!
Waiting for your responding.
Best Regards!
Technical Support Engineer
Technical Support Department
E-mail: msi.com.tw
[Post edited by Glenn]

Quote from: Indigian on 15-June-05, 19:41:43
Good news and good work guy's
On a side note to chakkasol....
are you using coolbits 1 or 2?
I heard that coolbits2 is the one for our later cards
Good question - coolbits 2. I happened to take a chance from this website and downloaded this file...ran it up against my antivirus and antispyware software and it looked clean. I simply ran the program and viola, coolbits functionality automatically added to the winxp registry. I cleaned out the msi DOT drivers first before I loaded this program. Even though I have tweaked on occasion the winxp registry to speed things up and make winxp shut down quicker, this was too complicated for me to do on my own.
The highest overclock with the MSIs DOT is 11% at 555/1100. My MSI card is actually very stable at 580/1160 for a 16% overclock. I have gotten it to 600/1200 but I usually run the coolbits stability program a few times and it has never failed at 580/1160. I am sure if I had a better cooling system than the stock fan it would probably go to 600/1200 or higher. At a 3DMark05 of 4133 (and much higher if I could get it stable at 600/1200, I would be bumping up against the stock speeds of the 6800s vid cards.
EDIT: Of course, if you download this coolbits 2 program you do so at your own risk...I take no responsibility for the download.
The coolbits download:
http://downloads.guru3d.com/download.php?det=815
The MSI 6600gt card that I purchased:
http://www.zipzoomfly.com/jsp/ProductDetail.jsp?ProductCode=321916
btw, I have ordered more stuff from ZZF than newegg...they seem cheaper (but dont always have the stock of newegg) and the stuff gets here 1 day sooner usually (west coast to east coast USA).

Multiple Problems with MSI 890FXA-GD65

I am having problems getting a clean build of new components to work. The components are:
motherboard is MSI 890FXA-GD65
processor is AMD Phenom II X2 565 Callisto
memory is 2x 4Gb G.Skill Ripjaws X model F2-12800CL9D (CAS 9, Unbuffered DDR3 1600)
disk drive is a Western Digital Caviar Black WD1002FAEX 1 TB SATA III
card is an MSI N460GTX Cyclone 768D5/OC.
power supply is an Antec NEO ECO 620C 620W
operating system is Windows 7
All items are brand new, and being assembled for the first time, so nothing is overclocked.
I have three problems. First is that the video output is flaky. I initially thought that the board wasn't POSTing, because I was getting no audible 'beeps' and there was no display output (does this board not have a speaker or speaker header?). Through trial and error, I discovered that the board was POSTing, but I could not see anything because of a strange video problem:
If the monitor is connected when the video output changes, then the video will not work, and disconnecting/reconnecting will not fix it. For example. If the video cable is plugged in during a cold start, I will get no video output. If I wait a few seconds until the Bios loads, and then plug in the video, then I get a video signal. However, if I leave it plugged in as the video output switches when Windows starts up, then I lose video again. Only by plugging in and then unplugging during the same video output mode can I use the output.
I have tried 2 different video cards (same mdodel number) with the same result. I have tried switching my memory with only 1 stick and with both sticks installed. I don't have another processor to try.
The second problem is that Windows will not run with the USB controller turned on in BIOS. It starts 'loading files' and then just hangs.
The third problem is that the MSI utility program will not run properly. I tried to install the updated chipset drivers, but the installation hangs.
Thanks for any help!! I am on the verge of returning the board to NewEgg after many hours of trying to troubleshoot this build.

Quote from: JimmyK on 15-February-11, 22:22:46
Thanks for the reply.
Sorry to be so newby, but where do I start memtest? The reported BIOS is the same version/date code as what is available from MSI...
>>Memtest86<<
Quote from: JimmyK on 15-February-11, 22:26:23
Thanks for the reply. I am using the DVI output on the video card connected to a VGA monitor with an DVI-VGA adapter.
No external USB connections have ever been installed.
I don't have any other DDR3 laying around. Is there a recommended memory list on the MSI site? I couldn't find one.
Regards
http://www.msi.com/file/test_report/TR10_2220.pdf
However its down to the CPU as memory controller is there.
You should use AMD tested memory sticks

Problems with msi p35 neo 2

Default problems with msi p35 neo 2
pc works fine when using windows and the net and emails
only when using 3d mark or games do i ever get problems
just help in getting the hole story 6 months ago got a msi neo2 install all my old components core 2 duo 4 gig ram form a diffrent board works fine but never used it playing games just used for the net and email shoping seamed to work fine but
tryed playing a game 2 months later command and conquer 3 pc was some times freeze or graphics artefacts on screen assumed vga card faulty got another graphics card geforce 8600gts installed still the same in the last month got round to playing with the pc again and installed new g7 780 watt power supply and ati hd 4870 graphics card
now i can use 3d mark some times it will go through once or just freeze or 3d mark stops the test
temps on the board (from msi dual core center temps cpu 33oc system 47oc)
memory voltage 2.1
any one know the settings for the ram
more details you need
System Details
MotherboardEdit Value
msi p35 neo2 fr
Motherboard BIOSEdit Value
latest
CPUEdit Value
core 2 quad 6600
CPU Overclock SpeedEdit Value
none
CPU HeatsinkEdit Value
standard intel that come with cpu
CPU Idle TempEdit Value
N/A
CPU Load TempEdit Value
N/A
MemoryEdit Value
******* xms2 2x2 gb ddr2 part no cm2x2048 6400c4dmx
Memory VoltageEdit Value
N/A
Video Card(s)Edit Value
ati hd4870
Video Card SpeedEdit Value
N/A
Sound CardEdit Value
onboard
PSUEdit Value
g7 780 watt power extreme
Hard Drive(s)Edit Value
mator dimondmax 21
Optical Drive(s)Edit Value
N/A
Other CoolingEdit Value
3 80mm fans 1 frount 1 back 1 side
ModsEdit Value
N/A
Operating SystemEdit Value
windows 7

Quote
******* xms2 2x2 gb ddr2 part no cm2x2048 6400c4dmx
Quote
memory voltage 2.1
Make sure that the memory timings are not set to 4-4-4-x but that they are set to the defaults values (5-5-5-x). Also ensure, that the memory clock speed is not set to anything higher than 400 MHz (=DDR2-800). The voltage at these settings should not need to exceed 1.95V. So please lower it accordingly. In case the freezes still occure, please run memtest86+ to check your memory for errors.
Quote
msi dual core center
Please get rid of that tool for all further tests. Uninstall it completely from your system as it is known to cause crashes and freezes on its own terms when running.

Video problem with MSI 880G-E45 board

Does anyone know if the onboard video is automatically disabled by installation of a PCI-e x16 video card on this motherboard?
I want to run two monitors and I cannot figure out how to keep the onboard vga active when I have a video card in the PCI-e x16 slot.
Thanks!

I can't believe a Moderator on a Manufacturer's Forum is handing out such INCORECT information!!!!
Quote from: flobelix on 16-August-12, 12:43:00
Unfortunately bottom line is you can't use your onboard vga for another display besides a vga card powering different monitors. Using a discrete vga you are limited to it's multi-display abilities. Onboard vga will not work when vga card used. For using three monitors you could get an Eyefinity supporting Radeon as suggested or a GeForce GTX6xx. If your card is limited to dual display and you don't want to get a new one you'll stick with two monitors.
I submit this link (tomshardware.com/reviews/amd-780g-chipset,1785-6.html) as proof that it is possible to use both the on-board video and an added video card both simultaneously or in crossfire mode on a single display.
To further illustrate this fact further, I submit this link (amd.com/it/products/technologies/ati-hybrid-graphics/Pages/ati-hybrid-graphics.aspx) to AMD.com stating the purpose for their "Hybrid Crossfire" technology, and although their page does not show specificly that the MSI 880G-E45 motherboard supports this, THIS page Does! (msi.com/product/mb/880G-E45.html#/?div=Basic) --Scroll to the bottom to see the line stating "Hybrid Crossfire Support - Y"
When speaking with MSI customer support about this technology, you are directed to this page (msi.com/file/test_report/TR1_2233.pdf) which shows a list of compatible video cards, ALL of which supported the Hybrid Crossfire when tested by MSI.
Add "http:\\www." to each of the links...
"flobelix", perhaps it would be better to simply say "I Don't Know" rather than providing MSI's customers with incorrect information and suggesting that they spend more money on something else.
BTW, I have personally tried 2 different video cards (MSI Radeon HD 6670 1Gb DDR5) and the (Sapphire Radeon HD 6450 1Gb DDR3) that are NOT on MSI's list, and they did NOT work with the Hybrid crossfire.
I hope we can limit further suggestions to facts instead of guesses.
Smokintbird

BUG with Memory CAS-Latency with MSI i848P Neo-LS BIOS

I have a bug with MSI i848P Neo-LS BIOS. I try many MSI i848P with same trouble : the CAS Latency is always set to 2.0 even if the memory is CAS Latency 2.5.
It doesn't depend on PSU or others things (graphics card,...).
Try with Pentium 4C 2.6 or 2.8
But I have just one brand of memory (but many different sticks). Chips reference are VT56DD32M8PC-5 (256 or 512 Mb). This memory are reference as Cas Latency 2.5
If I set memory timings on SPD or manual : same result !!!
If I set memory speed on AUTO or 400 MHz : same result !!!
If I set other timings, then they are save correctly (ie : RAS# precharge set to 3 or 4).
I check timings with latest version of Memtest86+ V1.0 : http://www.memtest.org/
and of course, I get many errors.
The same memory tested on others mobo, give good results.
I try Windows XP installation and I get.... blue screens.
With some memory sticks : I have this message "memory timing too tighly",
if I press F1 to continue: then I get a memory cas latency of 2.5 with memtest86+ and then no error.
I try BIOS revision 1.0 (default) and 1.2: same result !!!
So, as I said before, I think this is a bug with the BIOS. I agree that a BIOS cannot detect correctly all kind of memory, but if you set memory timings manualy, then it must be set as you want ! ?
Any idea...
Thanks

H0 Alex,
You are correct.I have the same problem with my 875p neo lsr on bios 1.9. TH0S 0S B0OS BUG.but everyone says your psu is not enough or your rams isnt on the MSI Memory Compatability List.
why all of rams I try give same result?
MS0 boards works only with 10 or 20 ram.you don't say customer why you use this rams?
why in asus boards many os these rams working properly.This rams isnt on the MSI Memory Compatability List.but working.I try many no name rams and results are very good in all of the tests.
In my opinion MS0 bioses doesnt work good enough.
You don't drive a car.Car Drives you.

Deploy of 11.4.402.278 version with .MSI file

After the deploy of 11.4.402.278 version with .MSI file, the Controll panel, falsh 32, tab advanced shows the 11.4.402.278 version.
in control panel, install e remove application, the Flash version is always the preview 11.4.402.267 version.
So i can't obtain a correct report with SpiceWorks(a scan network software)because the installed version remain the 11.4.402.267.
If i install Flash 11.4.402.278 manually with the .exe files, in the installed application i find two versions installed and i must remove manually the 11.4.402.267 version.
Before the 11.4.402.278.msi release everything worked well.
For the deploy i use the Kaspersky Security Center Consolle.
Any ideas?

yes, it is September 17.
it seems to be an error in the installer written version because the Flash control panel shows the right version.

Managed server is not starting with MSI mode

Managed server not starting with MSI mode even though we enabled the managed server independence mode
Started the admin server and managed server first time enabled the MSI mode.
Restarted all admin and Managed server.
We have tested the following scenarios
scenarios1: Stopped the Admin server and restarted the Managed server with MSI mode it comes up.
scenarios2:Admin server is running but not able to connect to the managed server
In this scenario
we have removed the Network cable and restarted the managed server its throwing ldap error.
<Aug 14, 2010 1:58:32 PM SGT> <Error> <Security> <BEA-090870> <The realm "myrealm" failed to be loaded: weblogic.security.service.SecurityServiceException: com.bea.common.engine.ServiceInitializationException: weblogic.security.spi.ProviderInitializationException: [Security:090730]Failed to verify credential mapper LDAP hierarchy
netscape.ldap.LDAPException: failed to connect to server ldap://sgppsr00383:16827 (91)
at netscape.ldap.LDAPConnSetupMgr.connectServer(LDAPConnSetupMgr.java:515)
at netscape.ldap.LDAPConnSetupMgr.openSerial(LDAPConnSetupMgr.java:435) at netscape.ldap.LDAPConnSetupMgr.connect(LDAPConnSetupMgr.java:274)
at netscape.ldap.LDAPConnSetupMgr.openConnection(LDAPConnSetupMgr.java:199)
at netscape.ldap.LDAPConnThread.connect(LDAPConnThread.java:109)
at netscape.ldap.LDAPConnection.connect(LDAPConnection.java:1083) at netscape.ldap.LDAPConnection.connect(LDAPConnection.java:954)
at netscape.ldap.LDAPConnection.connect(LDAPConnection.java:781)
at weblogic.ldap.EmbeddedLDAPConnection.getAndInitDelegate(EmbeddedLDAPConnection.java:2031)
at weblogic.ldap.EmbeddedLDAPConnection.add(EmbeddedLDAPConnection.java:1065) at weblogic.security.providers.credentials.DefaultCredentialMapperLDAPHelper.addEntry(DefaultCredentialMapperLDAPHelper.java:537)
at weblogic.security.providers.credentials.DefaultCredentialMapperLDAPHelper.createOrgUnit(DefaultCredentialMapperLDAPHelper.java:432)
at weblogic.security.providers.credentials.DefaultCredentialMapperLDAPHelper.verifyHierarchy(DefaultCredentialMapperLDAPHelper.java:407)
at weblogic.security.providers.credentials.DefaultCredentialMapperLDAPHelper.<init>(DefaultCredentialMapperLDAPHelper.java:146) at weblogic.security.providers.credentials.DefaultCredentialMapperLDAPHelper.getInstance(DefaultCredentialMapperLDAPHelper.java:112)
at weblogic.security.providers.credentials.DefaultCredentialMapperProviderImpl.initialize(DefaultCredentialMapperProviderImpl.java:93)
at com.bea.common.security.internal.legacy.service.SecurityProviderImpl.init(SecurityProviderImpl.java:53)
at com.bea.common.engine.internal.ServiceEngineImpl.findOrStartService(ServiceEngineImpl.java:340) at com.bea.common.engine.internal.ServiceEngineImpl.findOrStartService(ServiceEngineImpl.java:292)
at com.bea.common.engine.internal.ServiceEngineImpl.lookupService(ServiceEngineImpl.java:263)
at com.bea.common.engine.internal.ServicesImpl.getService(ServicesImpl.java:71)
at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.initializeRealm(CommonSecurityServiceManagerDelegateImpl.java:461) at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.loadRealm(CommonSecurityServiceManagerDelegateImpl.java:822)
at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.initializeRealms(CommonSecurityServiceManagerDelegateImpl.java:851)
at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.initialize(CommonSecurityServiceManagerDelegateImpl.java:1007)
at weblogic.security.service.SecurityServiceManager.initialize(SecurityServiceManager.java:854) at weblogic.security.SecurityService.start(SecurityService.java:141)
at weblogic.t3.srvr.SubsystemRequest.run(SubsystemRequest.java:64) at weblogic.work.ExecuteThread.execute(ExecuteThread.java:209) at weblogic.work.ExecuteThread.run(ExecuteThread.java:181)
- with nested exception:
Managed server looking for ldap configuration from admin server.
I have checked the all configuration file same on both managed server and admin server.
Please let me know How to recover the managed server in this scenario.
Edited by: user10773210 on Aug 16, 2010 11:55 PM
Edited by: user10773210 on Aug 17, 2010 2:38 AM

thanks for the reply....
the managed server is pointing to jrokit_160_22_D1.1.1-3 jdk....the server has enough ram also...while running the managed server showing status 'STARTING' for long period of time...and the admin server health goes 'Warning' because of threadpool....when we stop the managed server then adminserver health becomes ok...

SOLUTION for my problems with MSI Z77A-GD65 + MSI N670 PE 2GD5/OC

Lately I had problems with my GTX 670 video card (MSI N670 PE 2GD5/OC) under Windows 7 Pro x64.
I got a lot of "Display driver stopped responding and has recovered" errors.
I had these errors once or twice a day, so I didn't really bother looking for an answer, also I couldn't reproduce the error.
Most games just worked fine, but not always... so I tried if I could reproduce the error.
I tried to stress test with MSI Kombustor and voila no windows error... noo... but the core voltage went to 0 mV within a minute and everything (screen / windows / kombustor) stuttered and I had to restart the system.
The strange thing was that the voltage went to 0 mV, but the GPU load went from 96% - 60% and back to 96%... why and how is this possible??
Now I could reproduce my problem... yes!
First I thought it was a driver problem, because I updated it to the newest version (310.70), so I tried to re-install an older driver and also the original MSI driver... no luck.
Maybe it could be a mainboard driver or some settings in windows, so I installed Windows 8... no luck.
Re-installed Windows 7 Pro x64 (basically because Windows 8 s*cks)... no luck.
I tried to put my video card in another system and there was no problem... so I thought my video card is not broken...
Maybe it's my my power supply... new power supply... no luck again... grrrr...
My solution was downgrading / flashing my mainboard (MSI Z77A-GD65) bios back to 1.5 instead of 1.7, because yes... live update had updated my bios... that was the problem.
I wanted to post this, because I couldn't really find the answer for my problem and maybe I can help a few people with the same configuration and problems.
Live well and... well you get the idea

Quote from: flobelix on 21-August-13, 04:12:05
Don't use TF II/TF III parts as they won't fit. Arctic Accelero Twin Turbo II or Accelero Mono PLUS are good value for money aftermarket solutions.
Thank you for the information and advice. As I was looking into those two, I noticed that Accelero's website claimed the Accelero Xtreme III would also fit, and NewEgg had it on sale, so that is what I wound up purchasing. It works quite well and is MUCH quieter than the Twin Frozr IV, even before the grinding noise started.
For anyone else considering this, please be aware that the Xtreme III is monstrously huge (it adds several inches to the length of the MSI N670 PE). Make sure you have plenty of room in your case for it.

FX8320 with MSI 760GA-P43 (FX) MS-7699 drop speed on high load

Similar Messages

Maybe you are looking for