FXO Card not responding

Hi I have a VIC2-4FXO card in my Cisco 2901 router and its not responding. i replaced it with another workiing card and still the new card didnt respond.
any advice anyone?
Thanks,
Surendra

hi,
yes, i can see it in my inventory and i am also seeing my PDVm in my inventory.
i dont have anything else on the router that is using dsp resources.

Similar Messages

Equium A100-338 - Flash Card not Responding

Everytime I close down World of Warcraft something pops up in the top left hand corner (looks like it should be a window but only top bar showing) which reads 'Toshiba Flash Card (Not Responding)'. What can I do to stop this from happening?
Im pretty sure it pops up throughout the game as well as I hear a ding.
I have a Equium A100-338.
Thanks for any help!

Hi,
a solution can be disabling the flash card service if you dont need your flash drive.
You can disable it just by following these steps:
- Go into Start -> settings -> Control Panel -> Administrative Tools -> Services
- Make a right click on "Smart Card" and left-click on "Properties"
- In the window which pops up you have to stop the service and disable it with choosing "Disabled" at the option "Startup Type"
After that your flashdrive service is disabled and you wont get that annoying errormessage anymore.
(I hope so :O )
Greets

Toshiba flash card not responding

I have had my laptop for several years and lately I've been frequently getting the pop-up message 'Toshiba flash card not responding'. It's almost impossible to click away this message. I think there's a relationship between this and the fact that Internet Explorer is slow to start up and sometimes stops running for no good reason when I am online.
How do I fix this?

the toshiba flash cards are the cards that appear at the top of your screen when you rollover it or when you perform a function using the FN button and any of the F keys them not functioning will not cause any problem with your internet explorer but whatever caused the Toshiba flash cards to not work might be making your IE not work

Fastmac wireless card not responding

Hi all,
I just purchased an 802.11n wireless card for my Mac Pro from FastMac. I've got a 2.8 GHz Quad-Core Intel Xeon machine and am running OS 10.5.8
I used these online instructions to install it. The admin at FastMac emailed and asked me to send the 'hardware overview' info off my System Profiler so that they would be sure to send me the correct card. The card had 3 antennae terminals marked 0, 1 and 2. There were 3 antennae wires in the Mac Pro marked 1, 2, and 3. I hooked wire 1 to terminal 1, wire 2 to terminal 2 and wire 3 to terminal 0. Not sure if this was correct or not. After reboot, I cannot get the card to recognize my airport extreme base station (fig 1). In my network preferences, I disconnected my ethernet connection and made appletalk active in the airport network (fig 2).
If one of the three antennae wires is not seated correctly on the card, would that cause a problem?
I'm kinda stumped.
Fig. 1
Fig. 2
Thanks in advance for any input.
Dennis
Dennis Roliff Photography
Message was edited by: wunwspirit

thanks to all who viewed.

AT MIO-16E-10 card not responding

My LabView test system with this DAQ card, stopped working one day. The program would just hang when started. I checked the hardware through Measurement & Automation Explorer and the card shows up fine. The resources check out with control panel in Windows. But if I try to run the View Resources or Test Panel, Explorer hangs and I have to CTRL-ALT-DEL. In Windows Control Panel, there are no conflicts reported.
Suspecting the card, I removed it and tried it in another computer. No problems, the card works fine when both viewing the resources or running the Test Panel.
It looks like a software problem, but I haven't changed anything on the system and it worked fine before. My NI-DAQ drivers are at 6.9.3f3 and M&AE is 2.20.3010
. The system with problems is Win95.
Any ideas?

Uninstalling and re-installing the driver didn't do it. There was more than one installation of the drivers on the system, so I tried to delete them all. I also remove all NI software from the system to start from scratch, but I still have the same problem.
Before I completely wipe the system and upgrade to Win98, is there any files on the system I should look for multiple copies of that may be causing the problem?

Air Card not responding

My 13 inch 2008 Macbook Pro has decided it does not have an AirCard installed anymore. Any suggestions? Still running Snow Leopard on that machine. Everything else seems ok. Checked the connections and visually checked. Nothing obvious.

Resolved. Apple replaced under AppleCare.

The pass 4 days now my iTunes Store is not responding, when I reload it all that comes up is a blank white page that says iTunes Store. Help please!!!! Cannot load my gift card to buy music and such!!!

The pass 4 days now my iTunes Store is not responding, when I reload it all that comes up is a blank white page that says iTunes Store. Help please!!!! Cannot load my gift card to buy music and such!!!

I tookyour suggestion and SUCCESS! I can now access the Itunes Store. A simple fix, and thanks so much!!.
Below is the advice you forwarded:
I found a solution to my problem.
> start menu
> accessories,
> right click on the command prompt icon and choose "run as administrator".
Once it opens, type in the following command...
netsh winsock reset
hit enter
You should get a message that the winsock reset successful and you will need to reboot your computer.
Reboot and when I reloaded itunes the store loaded fine.
Thanks again, -Dean Stoneburner

NI-Motion PXI Card Device Status = Is Not Responding

I am unable to communicate with my NI PXI-7358 motion controller card. The general tab in MAX for the card shows that "Device Status" = "Is Not Responding" see attached. I have un-mapped and re-mapped the remote device. I have also removed and re-seated the PXI card without any success.
Solved!
Go to Solution.
Attachments:
PXI-7358 - Is Not Responding.PNG ‏29 KB

Hi Jeffmg,
This seems to be a known issue. There is an internal knowledgebase documenting this problem and a potential solution.
The solution according to the KB article:
"This problem can occur when a previous board was mapped to the host machine. The NIMtnSvr.exe is based on Board ID's and sometimes gets stuck. To fix this, close any NI software running and then open the task manager and end the NIMtnSvr.exe process. This will shutdown the server and allow it to start from scratch the next time it runs. When you open MAX, the boards will appear on the local host correctly mapped."
-N
National Instruments
Applications Engineer

PXI Card Status = Is Not Responding

I am unable to communicate with my NI PXI-7358 motion controller card (NI-Motion 6.1.2 Driver, Max 3.1.1, LabVIEW 7.1, Windows XP). The general tab in MAX for the card shows that "Device Status" = "Is Not Responding" see attached. I have un-mapped and re-mapped the remote device. I have also removed and re-seated the PXI card without any success. Does this mean the card is no longer functioning and needs to be replaced? How can I further investigate this issue?
Solved!
Go to Solution.
Attachments:
PXI-7358 - Is Not Responding.PNG ‏29 KB

Duplicate issue of http://forums.ni.com/t5/Motion-Control-and-Motor-Drives/NI-Motion-PXI-Card-Device-Status-Is-Not-Resp...

Fxo card is not connecting dtmf calls

I have an analogue line that is being set up from GSM modem and connected to fxo card on VG router .The fxo card is configured to go to an automated message with option of pressing digits to take one to the right operator.i.e press 1 for....,2 for......,etc. Unfortunately,this is not working when i callled the number.Its looking like a DTMF issue,but i ve adjusted all the seeting that has to do with dtmf on the fxo card......Has anyone encounter any familiar issue?

Check to see if you have the voice license bundle for the router.
show license
Index 3 Feature: uck9
Period left: Life time
License Type: Permanent
License State: Active, In Use
License Count: Non-Counted
License Priority: Medium
Without the voice license, no voice ports can be configured on 2900 series routers.

Router Model 2801 with fxs/DID and FXO card.

Greetings.I am Yeoh here I just configured DID direct inward dial on the fxs port.RJ11 connection to pbx. dunno wheter it will function or not. should i configure the ring and voltage for the connection to run? Here i have router 2800 . Not really sure what is require to configure but the manager here says we need this running with pbx and only simple flat network. no other routing function used. the important part here is the voip configuration. I have two router one with fxs card another one with fxo. For what i understand is PBX connection plug to fx0 then from router a to router b using fe0/0 to fe 0/0 then from router b i connect it to the phone using FXS/DID is this correct? what is the configs to make my phone running. i plug it in but it seems not responding. no sound at all. just some small "TUK TUK TUK" voice in it.

Anyone can help me. Please.

PCI DIO 32HS (6533) Suddenly giving "The device is not responding to the first IRQ level" error, and no longer functioning.

Greetings NI folks,
I'm an oceanographer, and have an sidescan sonar data aquasition computer running Windows XP SP2, and NiDAQ 7.0 (Legacy). For several years, this machine has worked flawlessly, but today, I booted it up to test the system for an upcoming job, and I got some strange errors in our sonar program. I tranced the problem to our NI-6533 PCI-DIO-32HS card. I launched NI Automation Explorer to test that the card was responsive, and when I click the "test panel", I get an error: "The device is not responding to the first IRQ level." Continue (yes/no). If I click yes, I can test the digital i/o's, but nothing happens, and all the tests fail (nonresponsive). I tried moving the card to another PCI slot, tried forcing it to have a specific IRQ that was unused by anything else, and finally tried moving it to another computer that had never been used with the DIO card. I'm still getting the error, and the card is nonresponsive. I'm at the limit of my abilities, and would like to know if there's anything else I can do, or should we send the card back to NI for repair/diagnosis.
Thanks.

Duplicate Post
Best Regards
Hani R.
Applications Engineer
National Instruments

Problem with premiere and encore export, Adobe QT32 Server (Not Responding)

I could help.
When exporting to Encore or Premiere, the program block.
In the Activity Monitor shows me these two errors:
Adobe QT32 Server (Not Responding)
PPro Headless (Not Responding)
Technical Specifications:
MAC OS X 10.9.5
Adobe Suite CS6
graphics card: AJA KONA LHi
Can you help me please
Thank You

Have you checked out this post from Adobe? I know it says for After Effects but it definitely applies to Premiere too. We have some AJA cards whose components in /library/QuickTime were causing similar Adobe QT32 server hangups; removing them solved our issue but also broke compatibility with older apps like FCP 7.

Microsoft Word Freezing Repeatedly, Application Not Responding

Just wondering if anyone else was having issues with Microsoft Word from MS Office 2008, where you open the application, you type a few sentences, and the application freezes with the spinning circle of death that won't go away until you click the dock where it says "application not responding" and do a force-quit? You can leave the circle spinning for 10-20-30 minutes, and it never goes away.
Now for the weird part--this error only happens for me when I'm using a specific document on my computer. I can open Word, start a new document, type several paragraphs of text, and it works fine. But I've been working on an existing paper for about two months that all of a sudden started causing these freezes/crashes when editing it. It's about 30 pages roughly, no images, no big inserts that would take up a lot of memory (116 kb in size). And up until today, there were no problems. So why all of a sudden can't I edit anything on this paper without freezing the program?! I downloaded the Microsoft Office 2008 Service Pack 1 that was just released after this problem started, and ran all the recent Java and program updates through Software Update with computer restarts. I even copied the text from the Word document I was working on, pasted it into a new document, tried saving it as both .doc and .docx, and again the program still freezes when working with that text in a new file. This one baffles me. It's like the text within a document is somehow freezing the application. One thing I did notice is that the freezes seem to happen when I'm scrolling using a mouse wheel. Not always, but quite a bit. I suppose this is some memory issue related to several pages of text that the program can't render or process when you add new lines of text or scroll, but again, I can't figure why this paper I've been working on for months all of a sudden decided to start freezing Word today. Can you really only have 30 double-spaced pages of text in Word before it crashes?
Looks like I've found my reason to switch to Open Office, since I'm 3-4 days out from a deadline. Any other solution strategies would be welcome. Thanks.

Same problem here - Microsoft Word 2008 (update 12.1.7) will open fine, and then start the spinning pizza of death. Only way out is to force-quit the app. I've tried:
1) deleting plist and font cache files
2) uninstalling MS Office 2008, reinstalling and then re-applying updates 12.1.0 and 12.1.7
3) confirming that Apple's Font Card.app can verify all fonts
No luck. Currently I can't open any MS word doc without the spinning pizza of death.
If you are lucky enough that these symptoms only happen with a specific Word .doc file, I would see if the PC-originator could re-save the file as .RTF and resend. If you can then open it OK, you could revert back to .doc (or .docx) format. RTF format is Microsoft's interchange format. If there are anomalies in the .doc file, saving as .RTF can sometimes clean them up. Once done, you can revert back to native MS Word format.
...b

Office 2013 (Word, Outlook, Excel, Power point) are not responding after live update

I had problems all last week with my Office applications not responding. I tried to uninstall and reinstall the software which did not solve the problem. I then did a samsung 5 recovery to factory state and installed office all over again which temporally
worked. My computer then prompted a windows live update after which the same problem came back with windows application not responding.
Please help as this is holding up my work.

Hi,
Please check your update patch list, if you had installed the Office 2013 SP1. please try to update the display card dirve. See the below thread:
http://social.technet.microsoft.com/Forums/en-US/34401d63-6c3b-47e6-ab20-9ed9b70d890b/outlook-2013-sp1-unusable-since-sp1-update-?forum=officesetupdep
Regards,
George Zhao
TechNet Community Support

FXO Card not responding

Similar Messages

Maybe you are looking for