FXO does not work incoming or outgoing

Hi all,
I have an CME with 8.5 release and I inserted an VIC2 - 4FXO.
I configured the FXO Port as below:
voice-port 0/0/0
trunk-group ALL_COT
supervisory disconnect dualtone pre-connect
cptone PT
timeouts initial 5
timeouts interdigit 7
connection plar 201
caller-id enable
dial-peer voice 100 pots
corlist outgoing chamada-emergencia
description ** Outside Calls **
destination-pattern 6..
port 0/0/0
forward-digits all
Every time I tried to make a call I receive busy tone and when I see the status of the port I see:
Foreign Exchange Office 0/0/0 Slot is 0, Sub-unit is 0, Port is 0
Type of VoicePort is FXO
Operation State is DOWN
Administrative State is UP
The Last Interface Down Failure Cause is Administrative Shutdown
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 3 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 128 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 1000 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is plar
Connection Number is 201
Initial Time Out is set to 5 s
Interdigit Time Out is set to 7 s
Call Disconnect Time Out is set to 60 s
Power Denial Disconnect Time Out is set to 1000 ms
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for PT
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Station name None, Station number None
Caller ID Info Follows:
Standard BELLCORE
Caller ID is received after 1 ring(s)
Translation profile (Incoming):
Translation profile (Outgoing):
lpcor (Incoming):
lpcor (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Battery-Reversal is enabled
Number Of Rings is set to 1
Supervisory Disconnect is dualtone pre-connect
Answer Supervision is inactive
Hook Status is Off Hook
Ring Detect Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Dial Out Type is dtmf
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Percent Break of Pulse is 65 percent
GuardOut timer is 2000 ms
Minimum ring duration timer is 125 ms
Hookflash-in Timing is set to 600 ms
Hookflash-out Timing is set to 400 ms
Supervisory Disconnect Timing (loopStart only) is set to 350 ms
OPX Ring Wait Timing is set to 6000 ms
Secondary dialtone is disabled
Operation stus DOWN; also when I do hut and no shut the voice port stays on DORMANT status and the I receive the message:
Apr 20 14:47:10.671: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
Can you help on this, why my FXO is not working?
Even when I call the the line the line rings but on the CME the extension plar does not start ringing.
My country is PORTUGAL.
Best Regards,
Jose Carlos Silva

Hi Jose,
Firstly is this a UC-500 based CME? I am not aware of a 8.5 version for the UC-500 unless this is a pre-production release, as far as I am aware the UC-500 is only supported up to 8.1 at this stage.
It would also be good if you could provide a copy of your running configuration (With sensitive data removed like usernames and or passwords and peoples names and numbers), this will help us in understanding the system configuration.
It also seems that the system has not been configured with CCA as there are no identifying markers in the configuration you posted that would indicated this was a CCA build, which leads me to think that this is a CLI build right??
I am personally not very ofay with the Portugal carrier setup so I best not post up a configuration of what the Voice-Port looks like as it might not be compatible with your local carrier, but I am curious as to why your FXO ports start at 0/0/0 typically on a UC-500 system they would start at 0/1/0 as the first 4 voice ports are normally reserved for FXS (Unless of course this is different for your region), which again makes me wonder if this is a UC-500 system or maybe an ISR (2800 series or above)??
Please post up your configuration it will help out a tremendious amount.
Cheers,
David.

Similar Messages

HI,Have 10.10.3 version email system does not work at all it display emails up to the installation of the new version, no incoming or outgoing emails

HI,
Have 10.10.3 imac version- email system does not work at all it display emails up to the installation of the new version, no incoming or outgoing emails

That helped thanks-
I was able to solve this by deleting all "Envelop Index*"- and "ExternalUpdates*"-files in ~/Library/Mail/v2/MailData. After that I restarted Mail and let it reindex all mailboxes.

HT203712 I have a 2011 tahoe. My bluetooth functioned properly until I updated my iPhone. Now the iPhone connects to the Tahoe but when I try to call a number it does not work. Either it cals the number and has no outgoing or incoming sound or it just

I have a 2011 tahoe. My bluetooth functioned properly until I updated my iPhone. Now the iPhone connects to the Tahoe but when I try to call a number it does not work. Either it cals the number and has no outgoing or incoming sound or it just says it iis unable to complete the call.

I would check with the Auto dealer where the vehicle was purchased to check and see when the bluetooth software was last updated on your vehicle. With the vehicle being a 2011 and if the software has not been updated since the dropping of IOS 7 then obviously there will be software incompatibilities.
Good luck.

TS3276 outgoing mail does not work on telus

Everything works for incoming on my telus account, yet my outgoing that is setup exactly link my ipad does not work at all. Any help.

My iCloud mail is now working after my doing nothing. I still cannot send from verizon using apple service. When I go to connection doctor I get the spinning gear continuously indicating that it is trying to connect. I think my settings are ok. I have not changed anything and they had just been working previously

TS3276 My o2 email account does not work when sending from my MAC it will accept incoming mail but not send it gives me a message that o2 account (offline) my mac I have no problem with my iPhone or mac laptop. any suggestions please.

My o2 email account does not work when sending from my MAC it will accept incoming mail but not send it gives me a message that o2 account (offline) my mac I have no problem with my iPhone or mac laptop. any suggestions please.

Sorry for the delay...
I did what you've told me, new account and manually copied my files from Time Machine. I had lots of permissions problems, but at the end, almost everything is in order... It seems it had to be with some of the Apple Preferences, but I can't be sure, as most of them were dumped to the trash can.
I still don't have my Mail Rules back, unfortunately, although I did goggled some. It is a pity, as I had around 30 or 40 of them, getting my mail in order to each of its mailboxes, but it is a small price as the rest doesn't show the before syntoms.
Thanks for the help, anyway!!

Iphone4 - Two Gmail Accounts - Outgoing server does not work anymore

I started using my private Gmail account on my Iphone and everything worked fine (having found help in Youtube videos about how to set up Ingoing/Outgoing server).
Now I added my Gmail account from work (ends on .nl instead of .com - Dont know if that matters). I can now access both inboxes but I cannot send emails from BOTH accounts. I then deleted the new account but still cannot send emails from my first account anymore.
I found that under "settings->Mail,Contacts,Calendars->Gmail Account->AccountInfo->OutgoingMailserver SMTP" I now have a primary server which seems to connect to my first account and several "other SMTP server" which contain either details of the first account or the second account (which I actually deleted aleady).
Should I delete those additional servers? How can I do this? Does anyone have experience with this kind of issue?
Thanks a lot in advance.

I did put all the informations and still it does not work telling that these informations are not right!!!!
HELP please

Outgoing email does not work

i recently changed my mail setting per my Verizon Email Provide. I can receive mail in but can not send out mail from AppleMail.
my icon just keep spinning on the outgoing mail
what can i do?

You may have a corrupt email preference. Open Mail - Preferences - Accounts (choose your Verizon account) and re-input all the settings and retest. If this does not work refer to:
support.apple.com/kb/ts3276

I have a new iPhone 5 version 8.1 - incoming caller ID does not work and I cannot send or receive SMS messages

I have a new iPhone 5 version 8.1 - incoming caller ID does not work and I cannot send or receive SMS messages. ISP says everything is active on their side. I have just upgraded from Samsung with the same phone number and services. Help?

Hi cggturner,
I'm sorry to hear you are having issues with iOS 8.1. If you are still having issues with Caller ID and SMS Messaging, you may find the troubleshooting steps outlined in the following article helpful:
iOS: Troubleshooting Messages
Regards,
- Brendnen

How do I reject incoming calls on Ios7 when locked? Power button on top right does not work.

How do I reject incoming calls on Ios7 when locked? Power button on top right does not work.

I am also facing the same issues. Sometime i get an option to reject call and sometime i won't .
Tried all the basic troubleshooting i could from my end but nogo. Also tried complete reset by loosing data still the same results. Any suggestions and fix, Apple ???

My up button for volume does not work and need to turn incoming call volume up. is there an app to do this

my up volume button does not work and i need to turn the incall volume up. is there an app that does this?

Hey skeith75,
Thanks for the question. Based on the information you have provided, your iPhone may need to be serviced to fix that button. However, if in the meantime you would like a workaround for turning the volume up on a phone call, you can use Assistive Touch:
iOS: Using AssistiveTouch
http://support.apple.com/kb/HT5587
If you do wish to service your iPhone, the following link should help you get started with the process. Included, you will find information on topics such as warranty, service pricing, and express replacement service.
Apple - Support - Service Answer Center
http://www.apple.com/support/iphone/service/faq/
Thanks,
Matt M.

Microphone does not work in Facetime

Hi
I read other posts and in Maverik I didn't find simmilar problem, for most people their microphone does not work after few minutes, but in my case, microphone does not work at all in Facetime, so I can hear the other end, but they can not hear me! This happened after updating Mavericks.
My Mac specs:
Macbook Pro 2013
OSx 10.9.1 (Mavericks)
things I already tested:
I tried to use headphone and without headphone, but it didn't make any difference
Microphone works fine in Skype and other softwares (Audacity, YahooMessenger, etc.)
Tried with WiFi and with Ethernet cable
Internet speed is 2.3MBps
Router's firewall does not have any restriction for certain ports
Tried turning facetime Off and On
Tried to call iPhone 5s, iPad2 and MacBook Pro each in different network and different countries!
... and finally searching internet for hours (which obviously came up with nothing)
I'll be thankful if somebody help me through, all suggestions are welcome, so please don't hesitate to post.

Same issue here....
8-core Mac Pro, Lion, Original External iSight camera connected via FireWire 400 through the FireWire jack on the 23" Apple Cinema Display.
Audio and video work fine using iChat and making video clips through any/all apps.
However, using FaceTime.....incoming audio and video are fine, outgoing video is fine, but outgoing audio is missing. Nobady can hear me.
Sorry guys...you can't doll this one up or spin it in any other direction......it's a bug pure and simple.
Feel free to fix it whilst you're dealing with all the other problems that Lion has.
....sT

Maverick's Mail does not work with Gmail ! it works better with iOS 7

For info.
I do know how it's complex to program and more for an OS System.
Maverick's Mail DOES NOT work proprely with Gmail boxes ? Gmail incoming or outcoming messages are correctly notified on my iPhone 5s with iOS 7. But not on my Macbook Pro retina (end 2012) with Mavericks. One update was suppose to solve the trouble.
Hope you'll solve the problem as soon as possible. Bur not during the nights. But during your daytimes' work !
Wish you nice end of year's days.
And please get my best wishes for 2014. Hope you'll get a lot of these nice little moments of happiness.
Best regards.
Pascal

Have you checked your incoming and outgoing mail server settings?
If you are using IMAP, it should look something like the following:
Incoming Mail (IMAP) Server - Requires SSL
imap.gmail.com
Port: 993
Requires SSL:Yes
Outgoing Mail (SMTP) Server - Requires TLS
smtp.gmail.com
Port: 465 or 587
Requires SSL: Yes
Requires authentication: Yes
Use same settings as incoming mail server
If you are using POP3, it should look something like the following:
Incoming mail server type: POP3
Incoming mail (POP3 or IMAP) server: pop.gmail.com. Google Apps users, enter the server name provided, don't add your domain name in these steps.
Port: 995
Outgoing e-mail server (SMTP) name: smtp.gmail.com
Port: 465
Outgoing server requires authentication: enabled

N95 8GB unlokced , Vibrating alert does not work

Hi
I just bought used N95 8 GB from my friend which is locked to a network provider.
My friend took it to shop to unlock service provider (he didn't realise that service provider does it for free), now I tried to test income call vibration but it seems to me it does not work , I tried under Tool > Profile > Create new profile (vibrating on) ,,,,but still there is no vibration when I receive call!!!
I tried "Factory Settings" for the mobile but still same problem
Would unlock be the reason for that (I don't know if vibration was working before unlock) ?
Any other suggestion how to test that ?
Thanks

jimmyireland wrote:
1st see if you have the latest firmware installed, if you dont have the latest update and if problem still occurs after the update try a hard reset the code is Press *#7370#
if this fails you will need to take it to a nokia care centre.
1- Yes it already has updated firmware
2- I did a hard resst without any success.
3- Would unlocking process normally create this problem ?
Message Edited by zillah on 20-Jun-2009 12:02 AM

HT1222 I just installed this update and now I cannot access "Mail" at all. I tried reinstalling the program, but that does not work, either. Help!!!!!!

I just installed this update and now I cannot access "Mail" at all. I tried reinstalling the program, but that does not work, either. Help!

Paldeng, thanks for the suggestion. I've done all that. I can connect to the server, but apparently they are not recognizing my ID and password. I can use the server program if I don't go through Mail (using the same ID and password). My mother in another state with another provider has had the same email issue, as also my husband on his laptop who uses the same internet connection I do. His worked fine until we had it repaired at the Apple store and all the original programs reloaded (with the required updates, I assume). We can receive email in Mail, we just cannot send.
I contacted my service provider, and we went over my connections. They said it was not their problem and connected me with Apple, resulting in a charge to me because my warranty is long expired. Apple swears it is not their problem, it is the provider, so here I sit. My son was able to fix my Mom's Mail (she's 97) and got my husband's working also, until mine went out, by tweaking connection descriptions and ports remotely. The thing is, we had not messed with any of those settings, so what changed? I just did not want to bother my son again, as he has many other demands on his time.
Since this fiasco with the Mail v4.6 update, I'm wondering if something else was updated that works well with Lion and Mountain Lion, but does not work well with Snow Leopard and Leopard. I think the problem I had with the Mail update was that my Mail program had been renamed to Mail (original), and therefore was not being recognized by the update. Perhaps they had another tweak in there somewhere that is affecting outgoing mail connections?

Bluetooth on iPhone 6 does not work with car stereo

I have used iPhone 4, 4S, 5 and 5S on my car - my own and my families phones. They all work as intended with regard to music and most importantly telephony. My car (FORD S-MAX) has buttons etc. for phone navigation. My daughters and wifes 5S's still work.
When I paired my new iPhone 6, the pairing itself was successful, but it does not work at all.
1) Incoming calls show my own telephone number, regardless of who calls
2) I cannot use the car buttons for anything, neither pickup, hangup or anything else
3) Regardless of what I do, the Podcast starts playing, if I choose Bluetooth as sound input on car. If I click pause on Podcast, it resumes after a while, sometimes immediately.
4) If I use the phone to dial a number, the sound is not in the car, even if sound source is Bluetooth/Car. If I select something else and back to car, the sound is in the car.
Hopefully this is soon to be solved! Or is there already a solution out there?
Best regards
Matt, Denmark

My iPhone 6 pairs just fine with my 07 Z4 ,no idrive etc just the basic B/T install on a Business standard radio set up with e snap in connector for the iPhone
but not yet an iPhone 6 snap in
You may need to ensure you clear all ol pairings from Beemer they have a limited number of pairings that can be stored at one time
To dispel all the bad press my 6 also happily paired with my '13 X1 without any issues and with the correct snap in also plays audio
The issue is usually with iDrive which BMW do have some issues with

FXO does not work incoming or outgoing

Similar Messages

Maybe you are looking for