FXO port not going back onhook when call goes to CUC Voice mail.

HI All,
Quiet new to the voice world and have just set up a home lab and have run into the following problem.
When a call comes in from the PSTN and gets transferred to voicemail CUC, when the caller has left the message and hung up the FXO port on my Cisco 3825 does not go back on hook
If a call comes in from the PSTN and is answered on a phone registered to the CUCM and the internal user hangs up the FXO port goes back on hook but if the caller hangs up the FXO port does not go back on hook.
I am using H.323 between the 3825 & CUCM
PSTN ------->Voice Gateway 3825-------->CUCM-------->CUC
Anyone got any ideas as to why this is happening?
Thanks

Hi Shaun,
The router DSP port is not able to detect the disconnect tone sent by provider that is why FXO port is remaining off hook. When call is answered by IP phone then IP phone user can listen the disconnect tone when PSTN caller disconnectes the call and they will hang up the call so gateway is aware that call is disconnected and moves the port to ON hook state but CUE cannot understand the tone so it keeps the call active. To resolve the issue we ave to configure custom CPTONE. Kindly collect PCM capture for a test call. Disable capture after call is disconnected by PSTN caller. i have attached the document. Use the method according to your IOS version.
Using PCM capture we can findout the exact frequency and cadence of the disconnect tone sent by provider.

Similar Messages

I am having multiple problems with my iphone 4s, people can't hear me when I call, text messages don't always send, calls go straight to voice mail. I have all bars, have hard rest 3 times. I have called apple 4 times and gone to a store. No help.

I have had the 3g, 3gs, 4 and little if any problems. I made a major mistake buying the 4s. What a horrible phone. I must say, apple service is at best, BAD. Here are the basics. I am on the same network, I call the same people, I use the same text messages as I did with the 4. With the 4s, I will call someone and they will not be able to hear me. I have to hang up and recall. Or the phone just does nothing when I press call. Text messages acts like they send but when I go back the have been sent. Sometimes the calls go direct to voice mail.
Here's what I have done. Reset, did not help. Called apple, advisor said she would call me back in 5 minutes, after waiting for 5 days for the call, I recalled, they walked me through the same things I had already done, then said to take it to a store. So they set up an appointment for the only day I could get to it, 1 1/2 hours away, on my grand son's birthday. That was okay if they fixed it. So they hard reset it, we had to setup 4 email accounts, they would not allow me to restore because they said it was a software problem. So I had to download all the apps, lost a lot of data. No fun. But if it worked! So Monday back at work, guess what, same thing. When home and did another hard reset. Still no lick. Called apple again. They said they would replace my phone, all they needed was to put a hold on a credit card for $899 or drive a 1 1/2 hours to a store.
So anyone know a good andriod phone.
PS I got a email asking about the service each time and each time I told them what a horrible phone it was and how bad service was. I have yet to hear back. I guess they do not read them!

You're not speaking to Apple on in this forum, nor will someone from Apple see this post. We are just users like you and I.
Have you tried to restore or reset your phone?
Or contact your carrier in re: to your sim card

Why does my phone call go directly to voice mail when I call my daughter? No others do this.

Why does my phone call go directly to voice mail when I call my daughter. I can call anyone else and talk to the person I call.
I am using the IPhone 4
Your response is that she has it forwarded to voicemail. It is a Samsung -so she wants to know how she un forwards it,. Or is my phone directly to her voicemail. The 'Finger Tips" says to send a call directly to voicemail push On/Off twice. I did not knowingly do that
Message was edited by: EVELYN ESKRIDGE

cowboy
Clarifications... when you say "... only some calls..." and "... someone says they called..." - are these all from from one caller?
After following all these fine suggestions and eliminating them systematically, consider that this kind of stuff is as old as the cellphone system. A few possibilities that occur to me just regarding the network system:
you are in a habitually dead spot area. I have one in my own house!
you travel through many of these dead zones (traditionally called 'low-coverage' areas) - remember how big a deal the coverage maps were to us?
there is an issue with your network service provider's back-end system (my first thought - above)
keep plugging away amigo! I'll bet you get this solved.
CCC

I can record voice memos fine using the built-in iPhone 4 mic. And my Bluetooth headset (Jawbone Era) works fine when I leave messages on voice mail systems etc. when calling on the iPhone 4. However, I cannot record voice memos with my Bluetooth mic.

I can record voice memos fine using the built-in iPhone 4 mic. And my Bluetooth headset (Jawbone Era) works fine when I leave messages on voice mail systems etc. when calling on the iPhone 4, so it appears my headset mic is fine. I can also use voice activated dialing, although it fails miserably interpreting numbers. However, I cannot record voice memos with my Bluetooth mic. I just get barely audible static. Any suggestions? Thanks.

Hello, did you ever get an answer to your question? I just picked up a Jawbone Era and using on an iPhone 4s running 5.0.1. Seems to work fine on regular calls, but not on the built in Voice memos application. It worked fine on my older Jawbone Icon, but haven't tested on the 4s or iOS 5.
Thanks!

I delete my google contact by fixing the duplicate names, after that I could not add back my contact ? but calendar and e mail works

I delete my google contact by fixing the duplicate names, after that I could not add back my contact ? but calendar and e mail works

On my old I phone 3 at the setting it show "mail,contacts, calendars, reminders" but why I phone 4 only show "mail calendar, notes" is this why I can not get my contact back to my phone?

Galaxy s3. when I dial *86 for voice mail. it calls my wife's cell phone?????

when I dial *86 for voice mail. it calls my wife's cell phone????? I have Galaxy S3

c
From: Brian68
Sent: Friday, November 23, 2012 1:38 PM
To: <Personal information removed for privacy>
Subject: Re: Galaxy s3. when I dial *86 for voice mail. it calls my wife's cell phone????? - Re: Galaxy s3. when I dial *86 for voice mail. it calls my wife's cell phone?????
           Calls her phone. Just like a regular phone call.
           Re: Galaxy s3. when I dial *86 for voice mail. it calls my wife's cell phone?????
            created by Brian68 in My Verizon - View the full discussion
Message was edited by: Verizon Moderator

IPHONE 4S incoming calls go directly to voice mail. This is a brand new replacement phone. Prior phone didn't have this problem

IPHONE 4S incoming calls go directly to voice mail. This is a brand new replacement phone. Prior phone didn't have this problem

Slide up from the bottom of your display to access the control panel.
Look for the button (should be at the top) that shows a crescent moon.
Tap that button. It should say "Do not Disturb: Off".
Then try it out and let us know if it worked.

My iphone 4 speakers stopped giving me sounds when i play audio or video even while gaming. It works fine when ringing tunes of for voice mails. What is wrong with it?

My iphone 4 speakers stopped giving me sounds when i play audio or video even while gaming. It works fine when ringing tunes of for voice mails, even works fine with headsets. What is wrong with it?

well i'd seriosly say point a hot hair drier at the speakers as water has entered the phone most commonly via the home button but avoid getting it too hot let it cool every 3 minutes after constant drying. Don't worry I have honestly dont this with my iPhone 4 GSM 16GB. For future reference avoid letting it get wet.

Uc560 fxo port not answering incoming calls

Hi,
My customer is facing problem for incoming calls in uc560 fxo port.They have 12 PSTN lines which is connected to UC system.System is configured with Auto-Attendant also. almost all days they are facing this major issue of incoming call is not getting answered by UC560 and caller can hear the line is ringing.While the time of this problem I can see some of the FXO port status LED is UP and not disconnecting even if no one is on call also.Once remove the cable from the FXO port and connect it back the problem will solve for time being.What will be the reason for this issue of line getting held.Is there any configuration needs to change in FXO module? Below is the configuration I done on all 12 FXO ports. Please check and
suggest me a solution.

HI Paolo,
Thank you provoding the proper documentation .
On the system side I made the change by keeping companding type from a-law to u-law and enabled battery reverse.This setting works fine for last three days and now again the customer is facing the same problem of FXO port get held and incoming calls are just ringing and system is not answering even.
How to get proper solution for this issue????
Please help me............
Regards,
Rinchuraj

Call into an MGCP controlled FXO port not connecting

my setup is
PSTN --- GW --- CUCM --- 6921 phone
when we call from the PSTN then call rings and shows connected on the PSTN phone after about 10 sec the call disconnects with fast busy but the 4 digit plar does not ring at all, outgoing calls are working fine. Need help in resolving this issue
Shabbar

FXO is configured as loop start as below, cannot run the debug isdn
R_SCI_KQ#debug isdn q931
^
% Invalid input detected at '^' marker.
Registration
Registered with Cisco Unified Communications Manager 192.168.0.26
IP Address
192.168.100.6
End-Point Name
AALN/S0/SU0/0@R_SCI_KQ.sciafrica.net
Description
Device Pool
DP_KQ -- Not Selected -- Cisco Unity voice Mail Ports DP_DAR DP_DRC DP_MOZ DP_ZAM UCCX
Common Device Configuration
< None >
Media Resource Group List
MRGL < None >
Packet Capture Mode
None Batch Processing Mode
Packet Capture Duration
Calling Search Space
< None > CSS_AAR CSS_Block-Line-Tz-Restricted CSS_Block-Line-Tz-UnRestricted CSS_CdPTP-HQ-GW CSS_CngPTP-HQ-GW CSS_CngPTP-HQ-Phones CSS_Dial-Device-Tz-PSTN CSS_HQ_Calling CSS_ITSP CSS_PSTN CSS_SAB_Callpark CSS_SUBSCRIBE_HQ_PHONE KQ_CSS LOGISTICS_CSS MANAGERS_CSS MOZ_CSS RECEPTION_CSS SALES_CSS STAFF_CSS TECHNICAL_CSS VMRestrictedCSS
AAR Calling Search Space
< None > CSS_AAR CSS_Block-Line-Tz-Restricted CSS_Block-Line-Tz-UnRestricted CSS_CdPTP-HQ-GW CSS_CngPTP-HQ-GW CSS_CngPTP-HQ-Phones CSS_Dial-Device-Tz-PSTN CSS_HQ_Calling CSS_ITSP CSS_PSTN CSS_SAB_Callpark CSS_SUBSCRIBE_HQ_PHONE KQ_CSS LOGISTICS_CSS MANAGERS_CSS MOZ_CSS RECEPTION_CSS SALES_CSS STAFF_CSS TECHNICAL_CSS VMRestrictedCSS
Location
Hub_None Kenya Mozambique Phantom Shadow Zambia
AAR Group
< None > AAR_GRoup
Network Locale
< None > Argentina Australia Austria Belgium Brazil Canada China Colombia Cyprus Czech Republic Denmark Egypt Finland France Germany Ghana Greece Hong Kong Hungary Iceland India Indonesia Ireland Israel Italy Japan Jordan Kenya Korea Republic Lebanon Luxembourg Malaysia Mexico Nepal Netherlands New Zealand Nigeria Norway Pakistan Panama Peru Philippines Poland Portugal Russian Federation Saudi Arabia Singapore Slovakia Slovenia South Africa Spain Sweden Switzerland Taiwan Thailand Turkey United Kingdom United States Venezuela Zimbabwe Itu Chile Bulgaria Croatia Romania Serbia and Montenegro United Arab Emirates Oman Kuwait Algeria Bahrain Iraq Mauritania Republic of Montenegro Morocco Qatar Republic of Serbia Sudan Tunisia Vietnam Yemen Lithuania Latvia Estonia
Use Trusted Relay Point
Off On Default
Transmit UTF-8 for Calling Party Name
Called Party Transformation CSS
< None > CSS_AAR CSS_Block-Line-Tz-Restricted CSS_Block-Line-Tz-UnRestricted CSS_CdPTP-HQ-GW CSS_CngPTP-HQ-GW CSS_CngPTP-HQ-Phones CSS_Dial-Device-Tz-PSTN CSS_HQ_Calling CSS_ITSP CSS_PSTN CSS_SAB_Callpark CSS_SUBSCRIBE_HQ_PHONE KQ_CSS LOGISTICS_CSS MANAGERS_CSS MOZ_CSS RECEPTION_CSS SALES_CSS STAFF_CSS TECHNICAL_CSS VMRestrictedCSS
Use Device Pool Called Party Transformation CSS
Enable Caller ID

3825 FXO Port remains in off-hook after call

Hello,
I have a 3825 router with 8 FXO ports running Cisco IOS Software, 3800 Software (C3825-SPSERVICESK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2). The problem we are facing is that after a call is placed through any of the FXO ports and the call is ended by the user, the port remains in off-hook till a reset of the port is done or someone restarts the router. Only then is the port accessible again.
I am thinking of changing the cards, but i do not want to invest in replacing the cards and then find out that this doesnt solve the problem.
The wierd thing is that this issue started on its own accord not too long ago.
Comments and suggestions please!
Regards,
Femi

Hello,
I do not want to change the FXO card till I am sure that is the problem and I did state that I always have to reboot the router when the problem starts. Rebooting clears the problem but it is back immediately I attempt a call again and hang up that call.
I have timeouts call-disconnect already configured, see below:
voice-port 0/0/0
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/0/1
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 2626878
caller-id enable type 1
voice-port 0/0/2
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/0/3
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/0
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/1
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/2
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/3
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
Regards,
Femi

Mercedes User interface does not revert back after a call

I had my iPhone 4 paired to my Mercedes and was happily using the bluetooth connectivity for making and receiving calls .
But lately when I make a call by dialing from my phone and then disconnecting the call using the car control, the car screen does not revert back to what it was and it remains in the phone mode.
This does not happen when I pick up a call using the car control.
Any idea as to why this might be happening .

Uninstall then reinstall RNR. RNR does not like to be cancelled via task manager.... this creates a mess.
Reinstall may also fix your issue with productivity center..

How to check UC560 FXO Port Not Problem Question

Dear All,
We are newbie on Cisco UC560.
Our customer use Cisco UC560, ESW-520-24P and Cisco SPA 502G and 508G for their branch office replace old traditional PBX. Cisco UC560 have built-in VIC2-4FXO and VIC2-4FXS.
Our customer PSTN line connected to UC560 FXO port (1 line PSTN).
We receive report from our customer that they cannot make a call to PSTN and receive call from PSTN that connected to UC560 FXO port (on physical FXO port LED Green turn on). When the problem happen our customer has restart UC560 or shutdown FXO port from CLI.
We have do some test to our customer UC560.
- Moving PSTN line to another FXO port (example: port from 0/1/0 to 0/1/1). The result is same (cannot make call to PSTN and receive call from PSTN)
Today, We have checked on our customer UC560 via show voice port summary and found that port0/1/2 and 0/1/3 OPER status is up wihout cable connected to this port.
Our question:
- What command on UC560 to make sure FXO port on UC560 doesn't have problem?
We attach:
show tech-support voice
show tech-support
We hope you can give us information about this.
Thanks For Your Attention

Hi There,
If you cannot find the Indonesian "Disconnect Supervision" you may get away with using Singapores "Disconnect Supervision" as your carrier networks are similar to each other
Cheers,
David Trad.

WDA app not launched with SSO when called from portal

Hi,
we have configured our systems so that our portal (NW Portal 7.0) is issuing logon tickets and ERP6.0 is receiving them in the backend for single sign-on.
When launching a SAP GUI for Windows transaction (System admin->Support->SAP Application) to test if the SSO is set up correctly, all goes well and I'm able to call e.g. SU01 with logon tickets from the portal.
My problem is that when calling a Web Dynpro for ABAP application in the same backend system from the same portal, I get an error "SSO logon not possible; logon tickets not activated on the server" and need to login manually when starting the application.
When looking at the WDA app URL, I see http://<backend server>.<domain1>.com/... and the portal is sitting on http://<portal server>.<domain2>.com. Could it be a problem if the backend system is in another domain? And if yes, how come the SAP GUI for Windows launch then works (related to an http connection and domain relaxing?)? How to go forward and make it work all right?
Best regards,
Mikko

Hi Navarro,
Merry Xmas:)
>>We did the same test with the demo app from you (MS)
http://msdn.microsoft.com/en-us/library/windows/apps/hh202967(v=vs.105).aspxand it still don't work. (remember to setup
fast app resume)
Yes, I can reproduce your issue using the official sample.
I think this issue is caused by the mechanism of Fast app resume, please refer to the following reference:
#Fast app resume for Windows Phone 8
http://msdn.microsoft.com/en-us/library/windows/apps/jj735579(v=vs.105).aspx
Quote:
With Fast Resume, when an app is resumed, the system creates a new page instance for the target of the launch point and this page is placed on top of the app’s existing backstack.
This official sample can also help us to understand how it works:
https://code.msdn.microsoft.com/windowsapps/Fast-app-resume-backstack-f16baaa6
We could find that the Application.Launching event will not be triggered if we used Fast app resume, this will affect responding Toast's parameter(Deep Link).
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Mavericks 10.9-10.9.1 bug/issue/problem: external drives connected through thunderbolt or firewire are not put to sleep when iMac goes to sleep

Previous to Mavericks (10.9 - 10.9.1) I've had no issues with external firewire or thunderbolt connected drives to be put to sleep. However, since Mavericks all of my external drives are not put to sleep when my iMac, or Mac Pro go to sleep.
How can a company such as Apple, pushing people to have external devices like hard drives, is not on top of fixing this issue? Apple pushed for firewire and thunderbolt, thus All external drives I've owned are firewire. Because of speed. I bought thunderbolt adapters for firewire, and before Mavericks all worked great. Now that we have 10.9.1 update, this is still an issue!
I'm aware of the temporary solution of connecting the drive through USB to make it work, this is not a solution, but a hack.
Please let Apple know that this is a known issue, and there should be a fix for it. Everyone's data depends on it! Not only current external backups, but also external sensitive hard drives we rely on. Currently, the following makes are experiencing this issue: Lacie, OWC (Elite Pro), WD, Promise, Seagate, Toshiba, G-Drive.
Other Apple Support Communities related thread:
https://discussions.apple.com/thread/5486167?start=60&tstart=0
https://discussions.apple.com/message/23541363
External References:
http://blog.macsales.com/21004-upgrade-to-mavericks-drama-free-with-owc
http://forums.macrumors.com/showthread.php?t=1659332&page=3
If anyone finds how to solve this issue, please help by posting the steps or solution.

Same 2 issues with 10.9.3:
External FireWire drive WILL NOT spin down when Mac goes to sleep.
also
External FireWire drive WILL NOT spin down for inactivity despite “Put hard disks to sleep when possible” is checked in energy saver.
This has been going on since the launch of Mavericks and no solution found yet.
USB ports work normally.

FXO port not going back onhook when call goes to CUC Voice mail.

Similar Messages

Maybe you are looking for