FXO ports got jammed after a call is placed

Hi team.
We have a analog line connected to an FXO port, every time we make a call through this line something happens and it's required for us to go to the gateway, unplug and plug again the line, next time anybody makes a call, it shows the same behavior in the line.
Best regards
Fernando

You can refer to the many threads on the same subject
http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a00800ae2d1.shtml

Similar Messages

3825 FXO Port remains in off-hook after call

Hello,
I have a 3825 router with 8 FXO ports running Cisco IOS Software, 3800 Software (C3825-SPSERVICESK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2). The problem we are facing is that after a call is placed through any of the FXO ports and the call is ended by the user, the port remains in off-hook till a reset of the port is done or someone restarts the router. Only then is the port accessible again.
I am thinking of changing the cards, but i do not want to invest in replacing the cards and then find out that this doesnt solve the problem.
The wierd thing is that this issue started on its own accord not too long ago.
Comments and suggestions please!
Regards,
Femi

Hello,
I do not want to change the FXO card till I am sure that is the problem and I did state that I always have to reboot the router when the problem starts. Rebooting clears the problem but it is back immediately I attempt a call again and hang up that call.
I have timeouts call-disconnect already configured, see below:
voice-port 0/0/0
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/0/1
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 2626878
caller-id enable type 1
voice-port 0/0/2
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/0/3
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/0
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/1
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/2
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
voice-port 0/1/3
supervisory disconnect dualtone mid-call
compand-type a-law
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 21000
description FXO CONNECTION TO PSTN
caller-id enable
Regards,
Femi

Uc560 fxo port not answering incoming calls

Hi,
My customer is facing problem for incoming calls in uc560 fxo port.They have 12 PSTN lines which is connected to UC system.System is configured with Auto-Attendant also. almost all days they are facing this major issue of incoming call is not getting answered by UC560 and caller can hear the line is ringing.While the time of this problem I can see some of the FXO port status LED is UP and not disconnecting even if no one is on call also.Once remove the cable from the FXO port and connect it back the problem will solve for time being.What will be the reason for this issue of line getting held.Is there any configuration needs to change in FXO module? Below is the configuration I done on all 12 FXO ports. Please check and
suggest me a solution.

HI Paolo,
Thank you provoding the proper documentation .
On the system side I made the change by keeping companding type from a-law to u-law and enabled battery reverse.This setting works fine for last three days and now again the customer is facing the same problem of FXO port get held and incoming calls are just ringing and system is not answering even.
How to get proper solution for this issue????
Please help me............
Regards,
Rinchuraj

Need a sample cme with multiple fxo ports, hunt fashion

hi,
anyone kind enough to provide a sample working configuration of multiple fxo ports (each being a pstn line) and I assuming the telco is doing hunting...
so let's say 4 lines, if line 1 is busy the call is sent by the telco on line 2 and so on...
incoming and outgoing.
thank you very much!!
I did google it and can't find anything with multiple fxo ports.

trunk group 1
max-calls voice 4 (or however many POTS lines you want to use)
hunt-scheme round-robin (or whatever method you like)
voice-port 0/0/0
trunk-group 1
connection plar opx XXXX (extension)
caller-id enable
voice-port 0/0/1
trunk-group 1
connection plar opx XXXX
caller-id enable
voice-port 0/0/2
trunk-group 1
connection plar opx XXXX
caller-id enable
voice-port 0/0/3
trunk-group 1
connection plar opx XXXX
caller-id enable
dial-peer voice 1 pots ( I like creating this for troubleshooting, by default cisco router accept incoming calls)
trunkgroup 1
incoming called-number .
direct-inward-dial
dial-peer voice 2 pots
trunkgroup 1
destination-pattern 8[2-9]...... (8 for an outside line or 9 or nothing, then adjust your forward-digits to match)
forward-digits 7
dial-peer voice 3 pots
trunkgroup 1
destination-pattern 81[2-9]..[2-9]......
forward-digits 11
dial-peer voice 4 pots
trunkgroup 1
destination-pattern 8911
forward-digits 3
dial-peer voice 5 pots
trunkgroup 1
destination-pattern 911
forward-digits 3

SPA400 FXO Ports are not dropt down after receving a call

Hi Team, does any one know why all FXO ports on a SPA400 are not disconnecting calls (there is not much configuration options to make sure we tier down ports)?
Example: I make a call and the SPA400 answer with the aa of my SPA9000 and after I hang up the line my SPA400 does not drop the call on the FXO so the line keeps busy all the time.
Please advise.

I'm looking at an older firmware version, so I'm not quiet sure if this is also available on your SPA400, under Setup then Voice tab , there's some parameter at the bottom for disconnect like , battery reversal as disconnect signal , tear down fxo port when silence detected for n seconds. Have you tried tweaking this settings? Also, on the SPA9000, you can try setting Reorder delay to 255 and see if it will help.

2900 FXO Port remains in off-hook after call

Hello
I have a 2900 router with FXO ports running Cisco IOS Software
c2900-universalk9-mz.SPA.151-4.M5.bin .
The problem is when the call is ended and we hung-up, port remains in off-hook and the line remains busy for long time.

CUCM 8.6.2.23900-10
Do you need all configuration or voice port?
voice-port 0/0/0
trunk-group PSTN
cptone IL
timeouts call-disconnect 1
timeouts wait-release 1
connection plar 58694150
impedance complex2
caller-id enable
voice-port 0/0/1
trunk-group PSTN
cptone IL
timeouts call-disconnect 1
timeouts wait-release 1
connection plar 58694151
impedance complex2
caller-id enable
voice-port 0/0/2
trunk-group PSTN
cptone IL
timeouts call-disconnect 1
timeouts wait-release 1
connection plar 58694152
impedance complex2
caller-id enable

FXO port not going back onhook when call goes to CUC Voice mail.

HI All,
Quiet new to the voice world and have just set up a home lab and have run into the following problem.
When a call comes in from the PSTN and gets transferred to voicemail CUC, when the caller has left the message and hung up the FXO port on my Cisco 3825 does not go back on hook
If a call comes in from the PSTN and is answered on a phone registered to the CUCM and the internal user hangs up the FXO port goes back on hook but if the caller hangs up the FXO port does not go back on hook.
I am using H.323 between the 3825 & CUCM
PSTN ------->Voice Gateway 3825-------->CUCM-------->CUC
Anyone got any ideas as to why this is happening?
Thanks

Hi Shaun,
The router DSP port is not able to detect the disconnect tone sent by provider that is why FXO port is remaining off hook. When call is answered by IP phone then IP phone user can listen the disconnect tone when PSTN caller disconnectes the call and they will hang up the call so gateway is aware that call is disconnected and moves the port to ON hook state but CUE cannot understand the tone so it keeps the call active. To resolve the issue we ave to configure custom CPTONE. Kindly collect PCM capture for a test call. Disable capture after call is disconnected by PSTN caller. i have attached the document. Use the method according to your IOS version.
Using PCM capture we can findout the exact frequency and cadence of the disconnect tone sent by provider.

Call disconnect on FXO port

Hi All,
I have an issue with call disconnect on FXO port. Call are getting disconnected as soon as it connects.
I observed the call takes the port 0/20 which has the command supervisory disconnect anytone
but in other ports I see supervisory disconnect dualtone mid-call
so I have changed with the second and got it working for some calls, In the debug vpm singal debugs I see remote device releases the call.
Could you tell me how this works and what are the debugs we could check to see what is the exact problem?
Number dialled are : 361000, 352788
Can you check? Logs and sh run is attached.
Thanks,
Lajith P

Beside that what you said Laith - I still think that you need specific tones for disconnect on FXO and only then your voice setup is going to work as it should. I can't comment on different version of IOS-es but maybe your previous one was better in handling this type of problem...if you don't have any specific requirement and must use 15.1 IOS you can always revert back to 15.0 and continue using your ports as already...
But if I was on your place - I would solve this problem once for all and then you don't have to worry about some upcoming new IOS
HTH,
Dragan

Issue with SPA525g registation and FXO port call calls are not disconnecting properly

Hi,
I have a UC540 and updated it to the latest IOS version with the latest firmware to my phones and i am having registration problems with SPA525g IP Phones. I updated the firmware of the phones as well and create manual tftp bindings with but still it is not registering. I run a couple of debugs (debug tftp events and debug ephone registration) I can see from the logs and in the phone that it is taking the proper VLAN and being discovered via CDP and being pointed to the TFTP server and still wont register. I can see that it is also taking its own .cnf file properly then the output sccp token regected invalid devices error is shown I have a SPA502G and it is working fine. Also there is a previous issue that all the voice port are shown as engage or offhook even the calls are disconnected thus make the main PSTN number busy am based in UAE and our service provider is etisalat I have check with them about the proper disconnection values but still it the same. That's why I have arrived in the conclusion to just update everything including the IOS and the phones firmware. I have put my config in this post, I am also trying to take the CCNA Voice exam on the 2nd week of april and I think that if i don't know how fix this issue for our customer then I would probably fail that exam. any suggestion and help is greatly appreciated cisco experts.
! Last configuration change at 13:36:42 ZP4 Thu Sep 13 2012 by Nick
! NVRAM config last updated at 13:45:41 ZP4 Thu Sep 13 2012 by Nick
version 15.1
parser config cache interface
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service internal
service compress-config
service sequence-numbers
hostname UC540
boot-start-marker
boot system flash:uc500-advipservicesk9-mz.151-2.T4
boot-end-marker
logging buffered 64000
enable secret 5 $1$3CIf$.rXyHeJQrwd97X/f2dS0M1
no aaa new-model
clock timezone ZP4 4 0
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-3558175224
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3558175224
revocation-check none
crypto pki certificate chain TP-self-signed-3558175224
certificate self-signed 01 nvram:IOS-Self-Sig#3.cer
dot11 syslog
dot11 ssid cisco-data
vlan 1
authentication open
dot11 ssid cisco-voice
vlan 100
authentication open
ip source-route
ip cef
ip dhcp relay information trust-all
ip dhcp excluded-address 10.1.3.1 10.1.3.10
ip dhcp pool phone
   network 10.1.3.0 255.255.255.0
   default-router 10.1.3.1
   option 150 ip 10.1.3.1
ip name-server 213.42.20.20
ip name-server 195.229.241.222
ip inspect WAAS flush-timeout 10
ip inspect name SDM_LOW cuseeme
ip inspect name SDM_LOW dns
ip inspect name SDM_LOW ftp
ip inspect name SDM_LOW h323
ip inspect name SDM_LOW https
ip inspect name SDM_LOW icmp
ip inspect name SDM_LOW imap
ip inspect name SDM_LOW pop3
ip inspect name SDM_LOW netshow
ip inspect name SDM_LOW rcmd
ip inspect name SDM_LOW realaudio
ip inspect name SDM_LOW rtsp
ip inspect name SDM_LOW esmtp
ip inspect name SDM_LOW sqlnet
ip inspect name SDM_LOW streamworks
ip inspect name SDM_LOW tftp
ip inspect name SDM_LOW tcp router-traffic
ip inspect name SDM_LOW udp router-traffic
ip inspect name SDM_LOW vdolive
no ipv6 cef
multilink bundle-name authenticated
stcapp ccm-group 1
stcapp
stcapp supplementary-services
port 0/0/0
fallback-dn 301
port 0/0/1
fallback-dn 302
port 0/0/2
fallback-dn 303
port 0/0/3
fallback-dn 304
trunk group ALL_FXO
max-retry 5
voice-class cause-code 1
hunt-scheme longest-idle
translation-profile outgoing PROFILE_ALL_FXO
trunk group ALL_FX0
voice call send-alert
voice rtp send-recv
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
sip
no update-callerid
voice class codec 1
codec preference 1 g711alaw
codec preference 2 g711ulaw
voice class dualtone-detect-params 1
freq-max-deviation 50
freq-max-power 0
freq-min-power 13
freq-power-twist 4
cadence-variation 6
voice class custom-cptone UAE-CUSTOM
dualtone disconnect
frequency 406
cadence 398 344 237 527 400
voice class custom-cptone CCAjointone
dualtone conference
frequency 600 900
cadence 300 150 300 100 300 50
voice class custom-cptone CCAleavetone
dualtone conference
frequency 400 800
cadence 400 50 200 50 200 50
voice class cause-code 1
no-circuit
voice register global
voice hunt-group 1 parallel
list 301,302,303
timeout 24
pilot 511
voice translation-rule 4
rule 15 // //
voice translation-rule 1000
rule 1 /.*/ //
voice translation-rule 1111
voice translation-rule 1112
rule 1 /^9/ //
rule 3 /^0/ //
voice translation-rule 2222
voice translation-rule 3265
rule 1 /$^..........$$/ /9\1/
rule 2 /$^.........$$/ /9\1/
rule 15 /$^ABCD$$/ /ABCD\1/
voice translation-profile CALLER_ID_TRANSLATION_PROFILE
translate calling 1111
voice translation-profile CallBlocking
translate called 2222
voice translation-profile INCOMING_CallerID_PROFILE
translate calling 3265
voice translation-profile OUTGOING_TRANSLATION_PROFILE
translate called 1112
voice translation-profile PROFILE_ALL_FXO
translate calling 4
voice translation-profile nondialable
translate called 1000
voice-card 0
dspfarm
dsp services dspfarm
license udi pid UC540W-FXO-K9 sn FHK143074G6
archive
log config
logging enable
logging size 600
hidekeys
username cisco privilege 15 secret 5 $1$vjNa$OFKLhupqR8al6x2b8Xmcj/
username adminac privilege 15 secret 5 $1$NDC.$PtD0y4YGIj5SqI1gghxWE1
username Nick privilege 15 secret 5 $1$iAmL$tsg7Jf2TEND1NN.h8z2dy/
ip tftp source-interface Loopback0
bridge irb
interface Loopback0
description $FW_INSIDE$
ip address 10.1.10.2 255.255.255.252
ip access-group 101 in
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/0
description $FW_OUTSIDE$
ip address 192.168.101.2 255.255.255.252
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
interface Integrated-Service-Engine0/0
description cue is initialized with default IMAP group
ip unnumbered Loopback0
ip nat inside
ip virtual-reassembly in
service-module ip address 10.1.10.1 255.255.255.252
service-module ip default-gateway 10.1.10.2
interface FastEthernet0/1/0
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/1
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/2
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/3
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/4
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/5
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/6
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/7
switchport access vlan 20
spanning-tree portfast
interface FastEthernet0/1/8
switchport access vlan 100
macro description cisco-switch
interface Dot11Radio0/5/0
no ip address
shutdown
ssid cisco-data
ssid cisco-voice
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
interface Dot11Radio0/5/0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0/5/0.100
encapsulation dot1Q 100
bridge-group 100
bridge-group 100 subscriber-loop-control
bridge-group 100 spanning-disabled
bridge-group 100 block-unknown-source
no bridge-group 100 source-learning
no bridge-group 100 unicast-flooding
interface Vlan1
no ip address
bridge-group 1
bridge-group 1 spanning-disabled
interface Vlan20
ip address 10.10.10.1 255.255.255.0
interface Vlan100
no ip address
bridge-group 100
bridge-group 100 spanning-disabled
interface BVI1
description $FW_INSIDE$
no ip address
ip nat inside
ip virtual-reassembly in
shutdown
interface BVI100
description $FW_INSIDE$
ip address 10.1.3.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http path flash:/gui
ip dns server
ip nat inside source list 1 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 192.168.101.1
ip route 10.1.10.1 255.255.255.255 Integrated-Service-Engine0/0
logging esm config
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 192.168.10.0 0.0.0.255
access-list 1 permit 10.1.3.0 0.0.0.255
access-list 1 permit 10.1.10.0 0.0.0.3
access-list 100 remark auto generated by SDM firewall configuration
access-list 100 remark SDM_ACL Category=1
access-list 100 deny   ip 192.168.10.0 0.0.0.255 any
access-list 100 deny   ip host 255.255.255.255 any
access-list 100 deny   ip 127.0.0.0 0.255.255.255 any
access-list 100 permit ip any any
access-list 101 remark auto generated by SDM firewall configuration##NO_ACES_8##
access-list 101 remark SDM_ACL Category=1
access-list 101 permit tcp 10.1.3.0 0.0.0.255 eq 2000 any
access-list 101 permit udp 10.1.3.0 0.0.0.255 eq 2000 any
access-list 101 deny   ip 10.1.3.0 0.0.0.255 any
access-list 101 deny   ip 192.168.10.0 0.0.0.255 any
access-list 101 deny   ip 192.168.101.0 0.0.0.3 any
access-list 101 deny   ip host 255.255.255.255 any
access-list 101 deny   ip 127.0.0.0 0.255.255.255 any
access-list 101 permit ip any any
access-list 102 remark auto generated by SDM firewall configuration##NO_ACES_6##
access-list 102 remark SDM_ACL Category=1
access-list 102 deny   ip 10.1.10.0 0.0.0.3 any
access-list 102 deny   ip 10.1.3.0 0.0.0.255 any
access-list 102 deny   ip 192.168.101.0 0.0.0.3 any
access-list 102 deny   ip host 255.255.255.255 any
access-list 102 deny   ip 127.0.0.0 0.255.255.255 any
access-list 102 permit ip any any
access-list 102 permit ip 192.168.101.0 0.0.0.3 any
access-list 103 remark auto generated by SDM firewall configuration##NO_ACES_8##
access-list 103 remark SDM_ACL Category=1
access-list 103 permit tcp 10.1.10.0 0.0.0.3 any eq 2000
access-list 103 permit udp 10.1.10.0 0.0.0.3 any eq 2000
access-list 103 deny   ip 10.1.10.0 0.0.0.3 any
access-list 103 deny   ip 192.168.10.0 0.0.0.255 any
access-list 103 deny   ip 192.168.101.0 0.0.0.3 any
access-list 103 deny   ip host 255.255.255.255 any
access-list 103 deny   ip 127.0.0.0 0.255.255.255 any
access-list 103 permit ip any any
access-list 105 permit ip any any
snmp-server community public RO
tftp-server flash:/phones/521_524/cp524g-8-1-17.bin alias cp524g-8-1-17.bin
tftp-server flash:/phones/5x5/spa5x5-7-1-3c.bin alias spa5x5-7-1-3c.bin
tftp-server flash:/phones/525/spa525g-7-4-8.bin alias spa525g-7-4-8.bin
control-plane
bridge 1 route ip
bridge 100 route ip
voice-port 0/0/0
cptone GB
station-id name Cordless
station-id number 329
caller-id enable
voice-port 0/0/1
cptone AE
caller-id enable
voice-port 0/0/2
cptone AE
caller-id enable
voice-port 0/0/3
cptone AE
caller-id enable
voice-port 0/1/0
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4FXO-0/1/0-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/1/1
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4 FXO-0/1/1-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/1/2
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
supervisory dualtone-detect-params 1
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4 FXO-0/1/2-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/1/3
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4 FXO-0/1/3-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/4/0
auto-cut-through
signal immediate
input gain auto-control -15
description Music On Hold Port
sccp local Loopback0
sccp ccm 10.1.3.1 identifier 1 version 4.0
sccp
sccp ccm group 1
associate ccm 1 priority 1
associate profile 1 register confprof1
dspfarm profile 1 conference
description DO NOT MODIFY, active CCA conference profile - CCA2.0 codec729
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
dial-peer cor custom
name internal
name local
name local-plus
name international
name national
name national-plus
name emergency
name toll-free
dial-peer cor list call-internal
member internal
dial-peer cor list call-local
member local
dial-peer cor list call-local-plus
member local-plus
dial-peer cor list call-national
member national
dial-peer cor list call-national-plus
member national-plus
dial-peer cor list call-international
member international
dial-peer cor list call-emergency
member emergency
dial-peer cor list call-toll-free
member toll-free
dial-peer cor list user-internal
member internal
member emergency
dial-peer cor list user-local
member internal
member local
member emergency
member toll-free
dial-peer cor list user-local-plus
member internal
member local
member local-plus
member emergency
member toll-free
dial-peer cor list user-national
member internal
member local
member local-plus
member national
member emergency
member toll-free
dial-peer cor list user-national-plus
member internal
member local
member local-plus
member national
member national-plus
member emergency
member toll-free
dial-peer cor list user-international
member internal
member local
member local-plus
member international
member national
member national-plus
member emergency
member toll-free
dial-peer voice 1 pots
port 0/0/0
no sip-register
dial-peer voice 2 pots
port 0/0/1
no sip-register
dial-peer voice 3 pots
port 0/0/2
no sip-register
dial-peer voice 4 pots
port 0/0/3
no sip-register
dial-peer voice 5 pots
description ** MOH Port **
destination-pattern ABC
port 0/4/0
no sip-register
dial-peer voice 50 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/0
dial-peer voice 51 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/1
dial-peer voice 52 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/2
dial-peer voice 53 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/3
dial-peer voice 54 pots
description ** FXO pots dial-peer **
destination-pattern A0
port 0/1/0
no sip-register
dial-peer voice 55 pots
description ** FXO pots dial-peer **
destination-pattern A1
port 0/1/1
no sip-register
dial-peer voice 56 pots
description ** FXO pots dial-peer **
destination-pattern A2
port 0/1/2
no sip-register
dial-peer voice 2000 voip
description ** cue voicemail pilot number **
destination-pattern 388
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 6 pots
description "catch all dial peer for BRI/PRI"
translation-profile incoming nondialable
incoming called-number .%
direct-inward-dial
dial-peer voice 57 pots
description ** FXO pots dial-peer **
destination-pattern A3
port 0/1/3
no sip-register
dial-peer voice 69 pots
destination-pattern 329
port 0/0/0
dial-peer voice 300 pots
trunkgroup ALL_FX0
description Local Numbers
destination-pattern 9T
forward-digits 9
dial-peer voice 301 voip
destination-pattern 2..
session target ipv4:192.168.201.2
dial-peer voice 303 pots
trunkgroup ALL_FXO
trunkgroup ALL_FX0
description **InternationalCall**
destination-pattern 88T
dial-peer voice 304 pots
trunkgroup ALL_FX0
description *EM1*
destination-pattern 9[1-9]T
forward-digits 3
dial-peer voice 302 pots
trunkgroup ALL_FX0
description **Mobiles**
destination-pattern 9.[0-9].[0-9]......
dial-peer voice 305 pots
trunkgroup ALL_FX0
description **800-**
destination-pattern 9[0-9][0-9][0-9]T
no dial-peer outbound status-check pots
telephony-service
sdspfarm conference mute-on 111 mute-off 222
sdspfarm units 5
sdspfarm tag 1 confprof1
conference hardware
video
fxo hook-flash
max-ephones 40
max-dn 300
ip source-address 10.1.3.1 port 2000
max-redirect 20
auto assign 1 to 1 type bri
calling-number initiator
service phone videoCapability 1
service phone webAccess 0
service dnis overlay
service dnis dir-lookup
timeouts interdigit 5
system message American Center
url services http://10.1.10.1/voiceview/common/login.do
url authentication http://10.1.10.2/CCMCIP/authenticate.asp
load 521G-524G cp524g-8-1-17
load 525G spa525g-7-4-8
load 501G spa5x5-7-1-3c
load 502G spa5x5-7-1-3c
load 504G spa5x5-7-1-3c
load 508G spa5x5-7-1-3c
load 509G spa5x5-7-1-3c
time-zone 35
date-format dd-mm-yy
voicemail 388
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
hunt-group logout HLog
moh MOH2.wav
multicast moh 239.10.16.16 port 2000
web admin system name cisco secret 5 $1$iDgA$MKNi2RWfsO0KjuC82kgLJ1
dn-webedit
time-webedit
transfer-system full-consult dss
transfer-pattern 9.T
transfer-pattern .T
secondary-dialtone 9
fac standard
create cnf-files version-stamp 7960 Aug 29 2012 12:00:04
line con 0
privilege level 15
logging synchronous
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
exec-timeout 0 0
logging synchronous
login local
transport input all
line vty 5 100
login local
transport input all
ntp master
end
Some of the output are not shown becaus it is to long I have attach the whole config for reference and any advice on how could I optimize and resolve my issues is greatly appreciated. Thanks

Nicolo - First off this stuff gets crazy sometimes. No worries about the exam. Sometimes when FXO ports go crazy it is due to battery reversal. If you go to the FXO port settings try turning battery reversal on and or off... depending on its current setting. See if that helps.
As for the 525s not registering.. These are inside the network correct? Are you connecting one directly to the UC500 with a Cat5E or Cat6 patch cable and the same thing happens? Does the MAC address on the phone match a MAC address under the EPHONE settings?
If you telnet into the UC500 can you execute a "dir" command at the CLI prompt and "CD" (change directory) into the phones folder and then the spa525g folder? Do files exist in there?
Also I only see an IP address under BVI100? This is the voice side of things what happened to the IP address under BVI1 (Data VLAN). Can you give us some information about the internal network? Cna you PING this phone system from the network? What IP address does it have?

Incorrect Caller ID on calls from outside line via FXO port.

   Have a public phone line connected to my CUCME 2801 router VIC2-2FXO card. All inbound calls are passed to DN-5001 (group number). Can receive and send calls without a problem, but incoming calls all show "911" for caller ID. Think this is simply an issue with the out bound dial-peer, of which the lowest numbered out bound dial-peer is for 911 services. Not sure how to correct this so inbound calls show the proper caller ID?
    Below is a copy of my CUCME show run output from the FXO port config thru all the dial-peers. Any pointers is greatly appreciated.
    Thanks.
           Kirk E.
voice-port 0/0/0
connection plar opx immediate 5001
voice-port 0/0/1
voice-port 0/2/0
station-id name POTS
station-id number 7000
voice-port 0/2/1
ccm-manager config
dial-peer voice 7000 pots
destination-pattern 5006
port 0/2/0
dial-peer voice 90 pots
description Emergency Services
destination-pattern 911
port 0/0/0
forward-digits 3
dial-peer voice 91 pots
description 10 Digit local dialing
destination-pattern [234].........
port 0/0/0
forward-digits 10
dial-peer voice 92 pots
description 11 Digit local/long distance dialing
destination-pattern 1[2348].........
port 0/0/0
forward-digits 11
dial-peer voice 93 pots
description Long Distance
destination-pattern 011T
port 0/0/0
prefix 011
dial-peer voice 94 pots
description Backup bench POTS phone
destination-pattern 7000
port 0/2/0
dial-peer voice 2 voip
destination-pattern 51..
session protocol sipv2
session target ipv4:172.16.2.155
dtmf-relay sip-notify
codec g711ulaw
no vad

Hi
Can you find the below:-
Hi
1- Please find the below table as the following link http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800b53c7.shtml
Caller ID          Requires VIC-2FXO-M1, VIC-2FXO-M2, VIC-4FXO-M1, VIC2-2FXO, VIC2-4FXO, or MRP3-8FXOM1
under voice-port
caller-id enable
2-If above configure and still have no caller id , please add the below commannds to the voice-port
caller-id alerting line-reversal
cptone ?               "based on your"
caller-id alerting ring 2    "the default is 1" maximum number of rings to be detected before a call is answered over an FXO voice port.
4-Do debug to make sure all ok
"debug vpm signal "
[0/3/0] get_fxo_caller_id:Caller ID received. Message type=128 length=31 checksum=74
Thank you
please rate all useful information

CME - Sending outbound calls to FXO port

Hi Guys,
Need your help for the below scenario.
Our customer has a CME where 4 FXO ports are already connected and working. Customer has added 2 more FXO port and few IP phones.
The requirement is when ever an outbound call is made from the newly configured IP phones, the call should go through the newly added FXO lines.
For eg ext 3001 , the outbound call should go through port 0/1/0
Already the prefix 9 is used for dialing the number and I guess only one prefix number can be used in CME.
I tried translation rule , cor list but none worked , the call is default going through the old fxo port and not to the new fxo port.
Can you guys help me with the configuration.
Regards
Sathya

Previous post on similar issue might be helpful -
https://supportforums.cisco.com/discussion/11431746/h323-choose-outbound-fxo-port-based-calling-number
Thnx

Transfer called number from FSX port SPA8000 to FXO port analog PBX.

Hello all!
I have CUCM 8.6 which connecting with SPA8000 by SIP trunk.
FXS port SPA8000 connect to FXO port analog PBX.
When I call from CUCM to analog PBX through SPA8000, SPA8000 does not pass called number in line.
Anybody have ideas?

Here is what I would recomend, I have set this up at several installations and it works well. The only difference would be that the ones that I have setup had more than 64K between sites but that is still doable so long as you keep the traffic on that link well regulated.
Anyhow. At each site install a VIC-2FXO and a VIC-2FXS into your 1760. You can use the higer density modules if you need more paths. Tie the FXOs to analog station ports on your PBX and the FXSs to analog CO ports. This may seem backwards but it is correct. Cisco's FXS is expecting to provide dialtone and the analog CO ports on the PBX are expecting to receive dial tone. Depending on what you are using for call processing ITS/CCME/CCM configure your gateway and your route pattern, etc. You will also need to be able to somehow access those fxs ports for outbound calls. You could have direct line access buttons on your phones and instruct users that when calling the remote site the must use lines 7 and 8 as an example. You could also setup a line pool code for these new lines.
Now when site A wants to call Site B, they dial whatever you wish them to dial. You do whatever translations you may wish prior to sending the call. Here is how the call flow works. User at site A accesses the line either by hitting a line button or dialing the line pool code. This grabs the analog line tied to one of the FXs ports on the router. The call is then sent over the 64K link. The router at Site B then uses one of the FXO ports to pass the call to an analog station port on the other PBX. To the PBX at site B it will appear as though someone pickedu picked up an analog station and dialed a local extension.
Hope this helps. If you need any further clarification on this let me know and I will try to clear it up further for you.

Calls out FXO port fail

I can't make any calls out this FXO port. Any ideas? Is it a telco issue?
IOS is 124-24.T4.bin
.Nov 18 06:12:29: htsp_timer_stop3
.Nov 18 06:12:29: [0/1/1] htsp_stop_caller_id_rx. message length 0htsp_setup_req
.Nov 18 06:12:29: htsp_process_event: [0/1/1, FXOLS_ONHOOK, E_HTSP_SETUP_REQ]fxols_onhook_setup
.Nov 18 06:12:29: [0/1/1] set signal state = 0xC timestamp = 0
.Nov 18 06:12:29: htsp_timer - 1300 msec
.Nov 18 06:12:29: [0/1/1] htsp_dsm_close_done
.Nov 18 06:12:30: htsp_process_event: [0/1/1, FXOLS_WAIT_DIAL_TONE, E_DSP_SIG_0110]fxols_disc_clear
.Nov 18 06:12:30: htsp_timer_stop2
.Nov 18 06:12:30: htsp_timer - 1300 msec
.Nov 18 06:12:31: htsp_process_event: [0/1/1, FXOLS_WAIT_DIAL_TONE, E_HTSP_EVENT_TIMER]fxols_wait_dial_timer htsp_dial
.Nov 18 06:12:33: htsp_process_event: [0/1/1, FXOLS_WAIT_DIAL_DONE, E_DSP_DIALING_DONE]fxols_wait_dial_done htsp_progress
.Nov 18 06:12:33: htsp_timer - 350 msec
.Nov 18 06:12:33: htsp_call_bridged invoked
.Nov 18 06:12:33: htsp_process_event: [0/1/1, FXOLS_WAIT_CUT_THRU, E_HTSP_VOICE_CUT_THROUGH]fxols_handle_cut_thru
.Nov 18 06:12:33: htsp_timer_stop
.Nov 18 06:12:34: htsp_process_event: [0/1/1, FXOLS_OFFHOOK, E_DSP_SUP_DISCONNECT]fxols_outgoing_sup_disc
.Nov 18 06:12:34: htsp_timer - 3000 msec
.Nov 18 06:12:37: htsp_process_event: [0/1/1, FXOLS_OFFHOOK, E_HTSP_EVENT_TIMER]fxols_disc_confirm
.Nov 18 06:12:37: htsp_timer_stop
.Nov 18 06:12:37: htsp_timer_stop2
.Nov 18 06:12:37: htsp_timer_stop3
.Nov 18 06:12:37: htsp_timer_stop3
.Nov 18 06:12:37: %VOIPAAA-5-VOIP_CALL_HISTORY: CallLegType 2, ConnectionId 3FE4209F37B14654000008A43C0E8F, SetupTime .06:12:29.778 GTM Tue Nov 18 2014, PeerAddress 605281980020, PeerSubAddress , DisconnectCause 11 , DisconnectText user busy (17), ConnectTime .06:12:33.158 GTM Tue Nov 18 2014, DisconnectTime .06:12:37.298 GTM Tue Nov 18 2014, CallOrigin 2, ChargedUnits 0, InfoType 2, TransmitPackets 102, TransmitBytes 4080, ReceivePackets 203, ReceiveBytes 4060
.Nov 18 06:12:37: %VOIPAAA-5-VOIP_FEAT_HISTORY: FEAT_VSA=fn:TWC,ft:11/18/2014 06:12:29.782,cgn:605281980020,cdn:080006099,frs:0,fid:45246,fcid:3FE4209F37B14654000008A43C0E8F,legID:10EF5,bguid:003FE4209F37B14654000008A43C0E8F
.Nov 18 06:12:37: htsp_process_event: [0/1/1, FXOLS_REMOTE_RELEASE, E_HTSP_RELEASE_REQ]fxols_offhook_release
.Nov 18 06:12:37: htsp_timer_stop
.Nov 18 06:12:37: htsp_timer_stop2
.Nov 18 06:12:37: htsp_timer_stop3
.Nov 18 06:12:37: [0/1/1] set signal state = 0x4 timestamp = 0
.Nov 18 06:12:37: htsp_timer - 2000 msec
.Nov 18 06:12:37: %VOIPAAA-5-VOIP_CALL_HISTORY: CallLegType 1, ConnectionId 3FE4209F37B14654000008A43C0E8F, SetupTime .06:12:29.790 GTM Tue Nov 18 2014, PeerAddress 080006099, PeerSubAddress , DisconnectCause 11 , DisconnectText user busy (17), ConnectTime .06:12:33.160 GTM Tue Nov 18 2014, DisconnectTime .06:12:37.280 GTM Tue Nov 18 2014, CallOrigin 1, ChargedUnits 0, InfoType 2, TransmitPackets 102, TransmitBytes 4080, ReceivePackets 203, ReceiveBytes 5684
.Nov 18 06:12:37: %VOIPAAA-5-VOIP_FEAT_HISTORY: FEAT_VSA=fn:TWC,ft:11/18/2014 06:12:29.786,cgn:605281980020,cdn:080006099,frs:0,fid:45247,fcid:3FE4209F37B14654000008A43C0E8F,legID:10EF6,bguid:003FE4209F37B14654000008A43C0E8F
.Nov 18 06:12:37: htsp_process_event: [0/1/1, FXOLS_GUARD_OUT, E_DSP_SIG_0110]
.Nov 18 06:12:39: htsp_process_event: [0/1/1, FXOLS_GUARD_OUT, E_HTSP_EVENT_TIMER]fxols_guard_out_timeout
.Nov 18 06:12:39: fxols_dsp_prealloc_clid_wait. Line reversal alerting DSP preallocation done
.Nov 18 06:12:39: [0/1/1] htsp_start_caller_id_rx:BELLCORE
.Nov 18 06:12:39: htsp_start_caller_id_rx create dsp_stream_manager
.Nov 18 06:12:39: [0/1/1] htsp_dsm_create_success returns 1
.Nov 18 06:12:39: htsp_process_event: [0/1/1, FXOLS_ONHOOK, E_DSP_SIG_0100]
voice-port 0/1/1
supervisory disconnect dualtone mid-call
cptone MX
timeouts interdigit 4
timeouts call-disconnect 3
timeouts wait-release 3
caller-id enable
caller-id alerting dsp-pre-allocate

Hi Jason,
Have you tried disabling the command "supervisory disconnect dualtone mid-call"?
Did you have DSP installed?
Regards

Restrict FXO ports on the Outgoing Calls.

I need to configure a restriction on the Outgoing Calls, i need the extension that start whit 1 (100,101,102,etc..) to only use the FXO ports 0/1/0 0/1/1 0/1/2 and the extensiones that start whit 2 (200,201,202,etc...) to only use the FXO ports 0/2/0 0/2/1 0/2/2, how can i make this happen ?

Hello Mario,
First off, this is not possible with CCA, this can only be done though CLI.
1. Setup seperate PSTN Trunk Groups. A: 0/1/0, 0/1/1, 0/1/2 B: 0/2/0, 0/2/1, 0/2/2
2. Setup Dial-Peers for each Trunk Group.
3. Setup COR list to restrict which users can use either Trunk Group.
That is the simple explaination, the actual setup can get quite complicated and lengthy.
Thank you,
Darren

CME fxo port problem

hi,
I have a 2801 CME and 2 fxo lines. Some times when both lines are seized (because of incoming and outgoing call) and after the phones are on hook the lines are still seized and are not released and when i removed the cables from fxo port, the led on each port start to blink in sequence and then when i reconnected, the port was busy again.. so i had to reboot the router to make it work. i changed the slot but dont think that it will cause any difference..do i need to upgrade the ios or some other issue..when i am calling the disconnect is fine but it happens some time when the line get stuck i have to reboot the router. one more thing when i changed the slot of the card the router didnt detected the change of slot and was showing fxo port on old slot. i rebooted the router to detect the fxo card on the right slot..sorry for the double post but no body was replying to i post it again..
Currently Being Moderated
May 12, 2012 11:49 AM (in response to Naresh Rathore)
FXO lines stuck/hang (2801 CME)
hi following is the sh run and sh version. cme output portion is removed
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.02.03 14:27:39 =~=~=~=~=~=~=~=~=~=~=~=
User Access Verification
Username: admin
Password:
Router_Home>en
Password:
Router_Home#term
Router_Home#terminal le
Router_Home#terminal length n   512
Router_Home#sh run
Building configuration...
Current configuration : 15203 bytes
! Last configuration change at 14:41:02 UTC Thu Feb 3 2011 by admin
! NVRAM config last updated at 14:38:09 UTC Thu Feb 3 2011 by admin
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router_Home
boot-start-marker
boot-end-marker
enable password cisco
no aaa new-model
clock calendar-valid
crypto pki trustpoint TP-self-signed-2416845307
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2416845307
revocation-check none
rsakeypair TP-self-signed-2416845307
crypto pki certificate chain TP-self-signed-2416845307
certificate self-signed 01
30820243 308201AC A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32343136 38343533 3037301E 170D3131 30323032 31373332
34335A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D32 34313638
34353330 3730819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100DFAC E4312F46 0F2BF242 E55FE0C1 73DC95F2 B2844295 DA691CE3 D9A202B1
77B1B0C3 5AE3D936 C4D786DB 7CFA6624 024C6A82 A29B3AAC 3BA89A77 5425A97A
6D79A88A C1327171 C88AA5E0 AB52F461 87FB472E A7622955 17C8F22C 58842EF4
4DFA422A 54E6B96A FA536C59 BD93FDCD 872C0586 08117535 2D13F1E0 A53E65AB
FE470203 010001A3 6B306930 0F060355 1D130101 FF040530 030101FF 30160603
551D1104 0F300D82 0B526F75 7465725F 486F6D65 301F0603 551D2304 18301680
14E940B0 E437790B 4B825CD2 0FA9020F 63C9ED3A ED301D06 03551D0E 04160414
E940B0E4 37790B4B 825CD20F A9020F63 C9ED3AED 300D0609 2A864886 F70D0101
04050003 8181006B D6136D19 6EF4DDCD B3AF591E 57B9B831 79578799 03862FCF
4AF772DE AC72FC85 3F6B6B20 81F528F0 F7B2CBD0 E9795060 C46AB102 AE2CDF53
11C39D67 B49A7AE8 FB619A0F 525543F7 8BA1D52C CABEFFEB 9E5EC7E7 938AA602
84F1ECD2 303E8609 A9AB0699 9078051B 1853BC9A 4B45F2A2 204310D5 8B34B5DD
2FA51064 EFF5D4
   quit
dot11 syslog
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.168.0.1
ip dhcp excluded-address 10.168.0.2
ip dhcp excluded-address 10.168.10.1
ip dhcp excluded-address 10.168.10.2
ip dhcp excluded-address 10.168.111.1 10.168.111.6
ip dhcp pool Data
   network 10.168.0.0 255.255.255.0
   default-router 10.168.0.1
   option 150 ip 10.168.10.1
   dns-server 212.72.1.186 212.72.23.4
ip dhcp pool VOICE
   network 10.168.10.0 255.255.255.0
   default-router 10.168.10.1
   option 150 ip 10.168.10.1
ip dhcp pool WLAN
   network 10.168.111.0 255.255.255.0
   default-router 10.168.111.1
   option 150 ip 10.168.10.1
   dns-server 212.72.1.186 212.72.23.4
ip host members.dyndns.org 204.13.248.112
ip name-server 212.72.1.186
ip name-server 212.72.23.4
ip ddns update method example_dyndns
HTTP
add http://whatisthis:[email protected]/nic/update?system=dyndns&hostname=<h>&myip=<a>
interval maximum 28 0 0 0
interval minimum 28 0 0 0
multilink bundle-name authenticated
voice-card 0
dsp services dspfarm
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
no supplementary-service h450.2
no supplementary-service h450.3
supplementary-service h450.12
h323
sip
registrar server expires max 600 min 60
username xxxxx password 0 xxxx
archive
log config
hidekeys
interface FastEthernet0/0
no ip address
ip nat inside
ip virtual-reassembly
speed auto
full-duplex
no keepalive
interface FastEthernet0/0.2
description ***** Voice LAN ******
encapsulation dot1Q 2
ip address 10.168.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/0.3
description ***** Data LAN ******
encapsulation dot1Q 3
ip address 10.168.0.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/0.4
description ***** Wireless LAN ******
encapsulation dot1Q 4
ip address 10.168.111.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/1
description $ES_WAN$
no ip address
shutdown
duplex auto
speed auto
interface ATM0/1/0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
interface ATM0/1/0.1 point-to-point
pvc 0/35
pppoe-client dial-pool-number 1
interface Dialer0
no ip address
interface Dialer1
mtu 1492
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1452
ip nat outside
ip virtual-reassembly
encapsulation ppp
ip route-cache flow
ip tcp adjust-mss 1412
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname xxxx
ppp chap password 0 xxxxx
ppp pap sent-username xxxx password 0 xxxxx
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer1
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip dns server
ip nat inside source list 101 interface Dialer1 overload
ip nat inside source route-map NAT_RMAP interface Dialer0 overload
access-list 101 permit ip 10.168.0.0 0.0.0.255 any
access-list 101 permit ip 10.168.111.0 0.0.0.255 any
route-map NAT_RMAP permit 10
match ip address 101
control-plane
voice-port 0/0/0
supervisor disconnect dualtone mid-call
input gain 14
compand-type a-law
cptone BE
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 121
impedance complex2
caller-id alerting dsp-pre-allocate
voice-port 0/0/1
supervisor disconnect dualtone mid-call
input gain 14
compand-type a-law
cptone BE
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 121
impedance complex2
caller-id alerting dsp-pre-allocate
voice-port 0/0/2
supervisor disconnect dualtone mid-call
input gain 14
compand-type a-law
cptone BE
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 121
impedance complex2
caller-id alerting dsp-pre-allocate
voice-port 0/0/3
supervisor disconnect dualtone mid-call
input gain 14
compand-type a-law
cptone BE
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 121
impedance complex2
caller-id alerting dsp-pre-allocate
dial-peer cor custom
name local
name longdistance
dial-peer cor list call-local
member local
dial-peer cor list call-longdistance
member longdistance
dial-peer cor list manager
member local
member longdistance
dial-peer cor list other
member local
dial-peer voice 1 pots
corlist outgoing call-longdistance
destination-pattern 0.T
port 0/0/0
dial-peer voice 2 pots
corlist outgoing call-longdistance
destination-pattern 0.T
port 0/0/1
dial-peer voice 3 pots
corlist outgoing call-longdistance
destination-pattern 0.T
port 0/0/2
dial-peer voice 4 pots
corlist outgoing call-longdistance
destination-pattern 0.T
port 0/0/3
dial-peer voice 5 pots
corlist outgoing call-local
destination-pattern 0[2,9].......
port 0/0/0
dial-peer voice 6 pots
corlist outgoing call-local
destination-pattern 0[2,9].......
port 0/0/1
dial-peer voice 7 pots
corlist outgoing call-local
destination-pattern 0[2,9].......
port 0/0/2
dial-peer voice 8 pots
corlist outgoing call-local
destination-pattern 0[2,9].......
port 0/0/3
dial-peer voice 9 pots
corlist outgoing call-local
destination-pattern 0800T
port 0/0/0
prefix 800
dial-peer voice 10 pots
corlist outgoing call-local
destination-pattern 0800T
port 0/0/1
prefix 800
dial-peer voice 11 pots
corlist outgoing call-local
destination-pattern 0800T
port 0/0/2
prefix 800
dial-peer voice 12 pots
corlist outgoing call-local
destination-pattern 0800T
port 0/0/3
prefix 800
telephony-service
no auto-reg-ephone
max-ephones 25
max-dn 25
ip source-address 10.168.10.1 port 2000
auto assign 1 to 20
timeouts interdigit 5
system message Home
max-conferences 8 gain -6
call-forward pattern .T
dn-webedit
transfer-system full-consult dss
transfer-pattern .T
ephone-dn 1 dual-line
number 101
label M.M Office (101)
description M.M Office (101)
name M.M Office
ephone 1
device-security-mode none
video
mac-address 1C17.D3C3.7A31
speed-dial 1 102 label "abc"
speed-dial 2 103 label "def"
speed-dial 3 104 label "hij"
speed-dial 4 113 label "klm"
speed-dial 5 104 label "nop"
speed-dial 6 105 label "qrst"
speed-dial 7 105 label "uvw"
type 7975
button 1:1 2:21
ephone-hunt 1 sequential
pilot 150
list 121
line con 0
exec-timeout 0 0
logging synchronous
login local
line aux 0
line vty 0 4
login local
transport input telnet
scheduler allocate 20000 1000
ntp master 2
ntp update-calendar
end
Router_Home#sh di
Router_Home#sh dia
% Ambiguous command: "sh dia"
Router_Home#sh ds
Router_Home#sh dsv   p
Router_Home#sh dspfarm
% Incomplete command.
Router_Home#sh dspfarm ?
all      Display all DSPFARM global info
dsp      Display DSPFARM DSPs information
profile Display DSPFARM profiles
Router_Home#sh dspfarm ds
Router_Home#sh dspfarm dsp
% Incomplete command.
Router_Home#sh dspfarm dsp             all
Total number of DSPFARM DSP channel(s) 0
Router_Home#sh ver
Router_Home#sh version
Cisco IOS Software, 2801 Software (C2801-ADVIPSERVICESK9-M), Version 12.4(15)T10, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 14-Sep-09 14:51 by prod_rel_team
ROM: System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)
Router_Home uptime is 21 hours, 11 minutes
System returned to ROM by power-on
System restarted at 17:31:27 UTC Wed Feb 2 2011
System image file is "flash:c2801-advipservicesk9-mz.124-15.T10.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 2801 (revision 6.0) with 237568K/24576K bytes of memory.
Processor board ID FCZ10491208
2 FastEthernet interfaces
1 ATM interface
2 Virtual Private Network (VPN) Modules
4 Voice FXO interfaces
1 DSP, 8 Voice resources
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
Router_Home#exit
Regards

Actually this has been answered already:
https://supportforums.cisco.com/thread/2148571?tstart=0
please do not open duplicate threads. You can delete you post using the Actions panel on the right.

FXO ports got jammed after a call is placed

Similar Messages

Maybe you are looking for