FXO-to-FXO

Hello,
I am getting my FXO port (2600 with 12.2(11)T) busy after the phone got on-hook.I've read about the disconnect problem, but I can't do anything using HICOM-100 like power-denial or disconnect tone. Some suggestions ?
I have another FXO port (1700 with 12.2(4)T3) with PABX COMDIAL DXP, I got the same problem, I tried to configure the PABX to send a digit when the call is disconnected and configure supervisory disconnect on FXO port, but it didn't work. Some suggestions ?
Thanks,
Cleber

Hi, I tried to configure supervisory disconnect with the PABX sending one digit when it disconnects, for example, the digit "*", so I configure the voice class with the two freq related to the "*" and applied it to voice port,like this, supervisory disconnect dualtone mid-call. But is not worked, I got my port off-hook, showed below.
PORT CODEC VAD VTSP STATE VPM 1/0/1 None y S_WAIT_RELEASE_NC FXOLS_PROCEEDING
Thanks,
Cleber

Similar Messages

FXO to FXO disconnect problem - Part1

Hi,
I have 2 sites connected through an hdlc leased line. Each site has router 1750 with one VIC - 2FXO.
Once a call is placed both FXO are stuck in the off hook state. So there is no way to make another call unless I shut down and turn on the ViC again.
I read the "famous" fxo disconnect problem file from Cisco but it didn't help.
I need to know:
1) Is this problem a bug on the FXO ports ?
2) Is this problem from the analog PBX side ?
3) How to solve this problem?
Thanks

Hi,
you can use FXS cards......you don't have any problem......
Problem is in disconnect reason....FXO card no detect disconnect tone from PBX....
Czech firm 2N sell special "disconnect module" fot these card......
(I'm sorry for my English...:o)

FXO to FXO disconnection problem -- Help me please.

My environment is as follows :
phoneA--<PBX>-FXO-<Router2821>--WAN--<Router2801>-FXO-<PBX>-phoneB
PhoneA NO# is 375
PhoneB NO# is 312
the related configurations from Router2821 are as follows:
voice-port 1/1/3
supervisory disconnect anytone
cptone TH
timeouts call-disconnect 5
timeouts ringing 10
timeouts wait-release 1
connection plar 614
dial-peer voice 8 pots
destination-pattern 379
port 1/1/3
the related configurations form Router2801 are as follows:
voice-port 0/0/3
supervisory disconnect anytone
cptone TH
timeouts call-disconnect 5
timeouts ringing 10
timeouts wait-release 1
connection plar 379
dial-peer voice 4 pots
destination-pattern 614
port 0/0/3
Steps to reproduce to problem are as follows:
1. Phone A dials to 379 ( the assigned NO on FXO of 2821 )
then the connection goes to 614( the assigned NO on FXO of 2801) by plar feature.
2. After got a tone from FXO of 2801, PhoneA dials to NO# 312( Phone B NO#)
and then PhoneB starts ringing.
3. While PhoneB is ringing( NoOne accepts the call ) PhoneA hooks-on the Phone.
--- The problem is PhoneB remains ringing and the FXO of both routers are not released ---
From the configuration above I have applied ringing timeout,disconnect timeout and wait-release timeout
to both routers. But it can't solve the problem.
Could anyone help me to solve this issue ?
Thanks a lot.

I also experienced same problem. I have diagram
- - RouterA <---> RouterB - -
when i put a call from phoneA to phoneB, the same problem occurs.
detail:
phoneA : 101
routerA : 1760
routerB : 1760
phoneB : 630
I have followed the procedure from linksite that had been posted. but the matter still occur. the information and result of debug
RouterB# sh voice call summ
PORT CODEC VAD VTSP STATE VPM STATE
2/0 g729r8 y S_CONNECT FXOLS_OFFHOOK
2/1 - - - FOLS_ONHOOK
(debug routerB)
Dec 23 00:08:26: htsp_process_event: [3/1, FXOGS_ONHOOK, E_HTSP_SETUP_REQ]fxogs_onhook_setup
Dec 23 00:08:26: [3/1] set signal state = 0x0 timestamp = 0
Dec 23 00:08:26: dsp_set_sig_state: [3/1] packet_len=12 channel_id=129 packet_id=39 state=0x0 timestamp=0x0
Dec 23 00:08:26: TGRM: reg_invoke_tgrm_call_update(0, 3, 1, 0, 1, TGRM_CALL_BUSY, TGRM_CALL_VOICE, TGRM_DIRECTION_OUT)
Dec 23 00:08:26: htsp_timer - 10000 msec
Dec 23 00:08:26: htsp_dsp_message: SEND/RESP_SIG_STATUS: state=0x4 timestamp=56945 systime=639197437
Dec 23 00:08:26: htsp_process_event: [3/1, FXOGS_WAIT_TIP_GROUND, E_DSP_SIG_0100]fxogs_start_dial
Dec 23 00:08:26: htsp_timer_stop
Dec 23 00:08:26: [3/1] set signal state = 0xC timestamp = 0
Dec 23 00:08:26: dsp_set_sig_state: [3/1] packet_len=12 channel_id=129 packet_id=39 state=0xC timestamp=0x0
Dec 23 00:08:26: htsp_process_event: [3/1, FXOGS_WAIT_DIAL_TONE, E_HTSP_EVENT_TIMER]fxogs_wait_dial_timer htsp_dial
Dec 23 00:08:26: htsp_process_event: [3/1, FXOGS_WAIT_DIAL_DONE, E_DSP_DIALING_DONE]fxogs_wait_dial_donehtsp_connect: no_offhook 0htsp_progress
Dec 23 00:08:26: htsp_timer - 350 msec
Dec 23 00:08:26: htsp_process_event: [3/1, FXOGS_WAIT_ONHOOK, E_HTSP_CONNECT]
Dec 23 00:08:26: [3/1, FXOGS_WAIT_ONHOOK, E_HTSP_CONNECT] -> ERROR: INVALID INPUT
Dec 23 00:08:26: ipm_modem_relay_supported : false
Dec 23 00:08:26: ipm_modem_relay_supported : false
Dec 23 00:08:26: htsp_process_event: [3/1, FXOGS_WAIT_ONHOOK, E_HTSP_VOICE_CUT_THROUGH]fxogs_handle_cut_thru
Dec 23 00:08:26: htsp_timer_stop
Dec 23 00:08:26: dsp_req_sig_state: [3/1] packet_len=8 channel_id=129 packet_id=40
Dec 23 00:08:26: htsp_dsp_message: SEND/RESP_SIG_STATUS: state=0x4 timestamp=56945 systime=639197438
Dec 23 00:08:26: htsp_process_event: [3/1, FXOGS_OFFHOOK, E_DSP_SIG_0100]
Dec 23 00:08:26: fxogs_stop_disc_timer
Dec 23 00:08:26: htsp_timer_stop2
Dec 23 00:08:26: htsp_dsp_message: SEND/RESP_SIG_STATUS: state=0x4 timestamp=57228 systime=639197465
Dec 23 00:08:26: htsp_process_event: [3/1, FXOGS_OFFHOOK, E_DSP_SIG_0100]
Dec 23 00:08:26: fxogs_stop_disc_timer
Dec 23 00:08:26: htsp_timer_stop2
note:
both router use IOS 12.3.17a, dspware 4.1.41
and the router doesn't have command for tip_ground
please help..

FXO Disconnect Problem

Hello,
I just would like to ask some ideas on FXO disconnect problem having a setup of FXO to FXO termination on both sites. I am using a VIC-2FXO-M2 on both Cisco 1760-V Router and these fxo ports are terminated to the PABX local.The voice port will disconnect 30minutes (approximately) after the call is terminated or it remainded off-hook although the call is already done.
We tried some fine tunings like enabling "battery-reversal" command, setting the timeout call disconnect to 5sec, timeout wait-release to 5sec. But the problem is still the same.
What is really the ideal fxo disconnect solution that we can do to lessen the 30minutes delay from off-hook to on-hook.
Looking forward for your great ideas.
Thank you.
Vivira Alastra

Dear Vivira,
The disconnection issue of FXO ports can really produce some gray hairs...
I have worked integrated to some cheap Panasonic PBX's in Nigeria where documentation is really scarce.
The solution that worked - but don't ask me how - was to try different combinations of CPTone on the Voice Ports. That did the job in our case.
You can also try the tedious job of measuring the disconnect tones ans analyse it e.g. in CoolEdit and then set up a Voice Class where you define the tones.
But try the CPTone settings first.
Good luck.
Peter

FXO does not work incoming or outgoing

Hi all,
I have an CME with 8.5 release and I inserted an VIC2 - 4FXO.
I configured the FXO Port as below:
voice-port 0/0/0
trunk-group ALL_COT
supervisory disconnect dualtone pre-connect
cptone PT
timeouts initial 5
timeouts interdigit 7
connection plar 201
caller-id enable
dial-peer voice 100 pots
corlist outgoing chamada-emergencia
description ** Outside Calls **
destination-pattern 6..
port 0/0/0
forward-digits all
Every time I tried to make a call I receive busy tone and when I see the status of the port I see:
Foreign Exchange Office 0/0/0 Slot is 0, Sub-unit is 0, Port is 0
Type of VoicePort is FXO
Operation State is DOWN
Administrative State is UP
The Last Interface Down Failure Cause is Administrative Shutdown
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 3 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 128 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 1000 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is plar
Connection Number is 201
Initial Time Out is set to 5 s
Interdigit Time Out is set to 7 s
Call Disconnect Time Out is set to 60 s
Power Denial Disconnect Time Out is set to 1000 ms
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for PT
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Station name None, Station number None
Caller ID Info Follows:
Standard BELLCORE
Caller ID is received after 1 ring(s)
Translation profile (Incoming):
Translation profile (Outgoing):
lpcor (Incoming):
lpcor (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Battery-Reversal is enabled
Number Of Rings is set to 1
Supervisory Disconnect is dualtone pre-connect
Answer Supervision is inactive
Hook Status is Off Hook
Ring Detect Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Dial Out Type is dtmf
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Percent Break of Pulse is 65 percent
GuardOut timer is 2000 ms
Minimum ring duration timer is 125 ms
Hookflash-in Timing is set to 600 ms
Hookflash-out Timing is set to 400 ms
Supervisory Disconnect Timing (loopStart only) is set to 350 ms
OPX Ring Wait Timing is set to 6000 ms
Secondary dialtone is disabled
Operation stus DOWN; also when I do hut and no shut the voice port stays on DORMANT status and the I receive the message:
Apr 20 14:47:10.671: %LINK-3-UPDOWN: Interface Foreign Exchange Office 0/0/0, changed state to operational status down due to cable removal
Can you help on this, why my FXO is not working?
Even when I call the the line the line rings but on the CME the extension plar does not start ringing.
My country is PORTUGAL.
Best Regards,
Jose Carlos Silva

Hi Jose,
Firstly is this a UC-500 based CME? I am not aware of a 8.5 version for the UC-500 unless this is a pre-production release, as far as I am aware the UC-500 is only supported up to 8.1 at this stage.
It would also be good if you could provide a copy of your running configuration (With sensitive data removed like usernames and or passwords and peoples names and numbers), this will help us in understanding the system configuration.
It also seems that the system has not been configured with CCA as there are no identifying markers in the configuration you posted that would indicated this was a CCA build, which leads me to think that this is a CLI build right??
I am personally not very ofay with the Portugal carrier setup so I best not post up a configuration of what the Voice-Port looks like as it might not be compatible with your local carrier, but I am curious as to why your FXO ports start at 0/0/0 typically on a UC-500 system they would start at 0/1/0 as the first 4 voice ports are normally reserved for FXS (Unless of course this is different for your region), which again makes me wonder if this is a UC-500 system or maybe an ISR (2800 series or above)??
Please post up your configuration it will help out a tremendious amount.
Cheers,
David.

Issue with SPA525g registation and FXO port call calls are not disconnecting properly

Hi,
I have a UC540 and updated it to the latest IOS version with the latest firmware to my phones and i am having registration problems with SPA525g IP Phones. I updated the firmware of the phones as well and create manual tftp bindings with but still it is not registering. I run a couple of debugs (debug tftp events and debug ephone registration) I can see from the logs and in the phone that it is taking the proper VLAN and being discovered via CDP and being pointed to the TFTP server and still wont register. I can see that it is also taking its own .cnf file properly then the output sccp token regected invalid devices error is shown I have a SPA502G and it is working fine. Also there is a previous issue that all the voice port are shown as engage or offhook even the calls are disconnected thus make the main PSTN number busy am based in UAE and our service provider is etisalat I have check with them about the proper disconnection values but still it the same. That's why I have arrived in the conclusion to just update everything including the IOS and the phones firmware. I have put my config in this post, I am also trying to take the CCNA Voice exam on the 2nd week of april and I think that if i don't know how fix this issue for our customer then I would probably fail that exam. any suggestion and help is greatly appreciated cisco experts.
! Last configuration change at 13:36:42 ZP4 Thu Sep 13 2012 by Nick
! NVRAM config last updated at 13:45:41 ZP4 Thu Sep 13 2012 by Nick
version 15.1
parser config cache interface
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service internal
service compress-config
service sequence-numbers
hostname UC540
boot-start-marker
boot system flash:uc500-advipservicesk9-mz.151-2.T4
boot-end-marker
logging buffered 64000
enable secret 5 $1$3CIf$.rXyHeJQrwd97X/f2dS0M1
no aaa new-model
clock timezone ZP4 4 0
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-3558175224
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3558175224
revocation-check none
crypto pki certificate chain TP-self-signed-3558175224
certificate self-signed 01 nvram:IOS-Self-Sig#3.cer
dot11 syslog
dot11 ssid cisco-data
vlan 1
authentication open
dot11 ssid cisco-voice
vlan 100
authentication open
ip source-route
ip cef
ip dhcp relay information trust-all
ip dhcp excluded-address 10.1.3.1 10.1.3.10
ip dhcp pool phone
   network 10.1.3.0 255.255.255.0
   default-router 10.1.3.1
   option 150 ip 10.1.3.1
ip name-server 213.42.20.20
ip name-server 195.229.241.222
ip inspect WAAS flush-timeout 10
ip inspect name SDM_LOW cuseeme
ip inspect name SDM_LOW dns
ip inspect name SDM_LOW ftp
ip inspect name SDM_LOW h323
ip inspect name SDM_LOW https
ip inspect name SDM_LOW icmp
ip inspect name SDM_LOW imap
ip inspect name SDM_LOW pop3
ip inspect name SDM_LOW netshow
ip inspect name SDM_LOW rcmd
ip inspect name SDM_LOW realaudio
ip inspect name SDM_LOW rtsp
ip inspect name SDM_LOW esmtp
ip inspect name SDM_LOW sqlnet
ip inspect name SDM_LOW streamworks
ip inspect name SDM_LOW tftp
ip inspect name SDM_LOW tcp router-traffic
ip inspect name SDM_LOW udp router-traffic
ip inspect name SDM_LOW vdolive
no ipv6 cef
multilink bundle-name authenticated
stcapp ccm-group 1
stcapp
stcapp supplementary-services
port 0/0/0
fallback-dn 301
port 0/0/1
fallback-dn 302
port 0/0/2
fallback-dn 303
port 0/0/3
fallback-dn 304
trunk group ALL_FXO
max-retry 5
voice-class cause-code 1
hunt-scheme longest-idle
translation-profile outgoing PROFILE_ALL_FXO
trunk group ALL_FX0
voice call send-alert
voice rtp send-recv
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
sip
no update-callerid
voice class codec 1
codec preference 1 g711alaw
codec preference 2 g711ulaw
voice class dualtone-detect-params 1
freq-max-deviation 50
freq-max-power 0
freq-min-power 13
freq-power-twist 4
cadence-variation 6
voice class custom-cptone UAE-CUSTOM
dualtone disconnect
frequency 406
cadence 398 344 237 527 400
voice class custom-cptone CCAjointone
dualtone conference
frequency 600 900
cadence 300 150 300 100 300 50
voice class custom-cptone CCAleavetone
dualtone conference
frequency 400 800
cadence 400 50 200 50 200 50
voice class cause-code 1
no-circuit
voice register global
voice hunt-group 1 parallel
list 301,302,303
timeout 24
pilot 511
voice translation-rule 4
rule 15 // //
voice translation-rule 1000
rule 1 /.*/ //
voice translation-rule 1111
voice translation-rule 1112
rule 1 /^9/ //
rule 3 /^0/ //
voice translation-rule 2222
voice translation-rule 3265
rule 1 /$^..........$$/ /9\1/
rule 2 /$^.........$$/ /9\1/
rule 15 /$^ABCD$$/ /ABCD\1/
voice translation-profile CALLER_ID_TRANSLATION_PROFILE
translate calling 1111
voice translation-profile CallBlocking
translate called 2222
voice translation-profile INCOMING_CallerID_PROFILE
translate calling 3265
voice translation-profile OUTGOING_TRANSLATION_PROFILE
translate called 1112
voice translation-profile PROFILE_ALL_FXO
translate calling 4
voice translation-profile nondialable
translate called 1000
voice-card 0
dspfarm
dsp services dspfarm
license udi pid UC540W-FXO-K9 sn FHK143074G6
archive
log config
logging enable
logging size 600
hidekeys
username cisco privilege 15 secret 5 $1$vjNa$OFKLhupqR8al6x2b8Xmcj/
username adminac privilege 15 secret 5 $1$NDC.$PtD0y4YGIj5SqI1gghxWE1
username Nick privilege 15 secret 5 $1$iAmL$tsg7Jf2TEND1NN.h8z2dy/
ip tftp source-interface Loopback0
bridge irb
interface Loopback0
description $FW_INSIDE$
ip address 10.1.10.2 255.255.255.252
ip access-group 101 in
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/0
description $FW_OUTSIDE$
ip address 192.168.101.2 255.255.255.252
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
interface Integrated-Service-Engine0/0
description cue is initialized with default IMAP group
ip unnumbered Loopback0
ip nat inside
ip virtual-reassembly in
service-module ip address 10.1.10.1 255.255.255.252
service-module ip default-gateway 10.1.10.2
interface FastEthernet0/1/0
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/1
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/2
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/3
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/4
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/5
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/6
switchport voice vlan 100
macro description cisco-phone
spanning-tree portfast
interface FastEthernet0/1/7
switchport access vlan 20
spanning-tree portfast
interface FastEthernet0/1/8
switchport access vlan 100
macro description cisco-switch
interface Dot11Radio0/5/0
no ip address
shutdown
ssid cisco-data
ssid cisco-voice
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
interface Dot11Radio0/5/0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0/5/0.100
encapsulation dot1Q 100
bridge-group 100
bridge-group 100 subscriber-loop-control
bridge-group 100 spanning-disabled
bridge-group 100 block-unknown-source
no bridge-group 100 source-learning
no bridge-group 100 unicast-flooding
interface Vlan1
no ip address
bridge-group 1
bridge-group 1 spanning-disabled
interface Vlan20
ip address 10.10.10.1 255.255.255.0
interface Vlan100
no ip address
bridge-group 100
bridge-group 100 spanning-disabled
interface BVI1
description $FW_INSIDE$
no ip address
ip nat inside
ip virtual-reassembly in
shutdown
interface BVI100
description $FW_INSIDE$
ip address 10.1.3.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip forward-protocol nd
ip http server
ip http authentication local
ip http secure-server
ip http path flash:/gui
ip dns server
ip nat inside source list 1 interface FastEthernet0/0 overload
ip route 0.0.0.0 0.0.0.0 192.168.101.1
ip route 10.1.10.1 255.255.255.255 Integrated-Service-Engine0/0
logging esm config
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 192.168.10.0 0.0.0.255
access-list 1 permit 10.1.3.0 0.0.0.255
access-list 1 permit 10.1.10.0 0.0.0.3
access-list 100 remark auto generated by SDM firewall configuration
access-list 100 remark SDM_ACL Category=1
access-list 100 deny   ip 192.168.10.0 0.0.0.255 any
access-list 100 deny   ip host 255.255.255.255 any
access-list 100 deny   ip 127.0.0.0 0.255.255.255 any
access-list 100 permit ip any any
access-list 101 remark auto generated by SDM firewall configuration##NO_ACES_8##
access-list 101 remark SDM_ACL Category=1
access-list 101 permit tcp 10.1.3.0 0.0.0.255 eq 2000 any
access-list 101 permit udp 10.1.3.0 0.0.0.255 eq 2000 any
access-list 101 deny   ip 10.1.3.0 0.0.0.255 any
access-list 101 deny   ip 192.168.10.0 0.0.0.255 any
access-list 101 deny   ip 192.168.101.0 0.0.0.3 any
access-list 101 deny   ip host 255.255.255.255 any
access-list 101 deny   ip 127.0.0.0 0.255.255.255 any
access-list 101 permit ip any any
access-list 102 remark auto generated by SDM firewall configuration##NO_ACES_6##
access-list 102 remark SDM_ACL Category=1
access-list 102 deny   ip 10.1.10.0 0.0.0.3 any
access-list 102 deny   ip 10.1.3.0 0.0.0.255 any
access-list 102 deny   ip 192.168.101.0 0.0.0.3 any
access-list 102 deny   ip host 255.255.255.255 any
access-list 102 deny   ip 127.0.0.0 0.255.255.255 any
access-list 102 permit ip any any
access-list 102 permit ip 192.168.101.0 0.0.0.3 any
access-list 103 remark auto generated by SDM firewall configuration##NO_ACES_8##
access-list 103 remark SDM_ACL Category=1
access-list 103 permit tcp 10.1.10.0 0.0.0.3 any eq 2000
access-list 103 permit udp 10.1.10.0 0.0.0.3 any eq 2000
access-list 103 deny   ip 10.1.10.0 0.0.0.3 any
access-list 103 deny   ip 192.168.10.0 0.0.0.255 any
access-list 103 deny   ip 192.168.101.0 0.0.0.3 any
access-list 103 deny   ip host 255.255.255.255 any
access-list 103 deny   ip 127.0.0.0 0.255.255.255 any
access-list 103 permit ip any any
access-list 105 permit ip any any
snmp-server community public RO
tftp-server flash:/phones/521_524/cp524g-8-1-17.bin alias cp524g-8-1-17.bin
tftp-server flash:/phones/5x5/spa5x5-7-1-3c.bin alias spa5x5-7-1-3c.bin
tftp-server flash:/phones/525/spa525g-7-4-8.bin alias spa525g-7-4-8.bin
control-plane
bridge 1 route ip
bridge 100 route ip
voice-port 0/0/0
cptone GB
station-id name Cordless
station-id number 329
caller-id enable
voice-port 0/0/1
cptone AE
caller-id enable
voice-port 0/0/2
cptone AE
caller-id enable
voice-port 0/0/3
cptone AE
caller-id enable
voice-port 0/1/0
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4FXO-0/1/0-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/1/1
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4 FXO-0/1/1-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/1/2
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
supervisory dualtone-detect-params 1
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4 FXO-0/1/2-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/1/3
trunk-group ALL_FX0 64
translation-profile incoming INCOMING_CallerID_PROFILE
supervisory disconnect dualtone mid-call
supervisory custom-cptone UAE-CUSTOM
input gain 14
cptone GB
connection plar opx 511
impedance 600c
description Configured by CCA 4 FXO-0/1/3-Custom-BG
bearer-cap Speech
caller-id enable
voice-port 0/4/0
auto-cut-through
signal immediate
input gain auto-control -15
description Music On Hold Port
sccp local Loopback0
sccp ccm 10.1.3.1 identifier 1 version 4.0
sccp
sccp ccm group 1
associate ccm 1 priority 1
associate profile 1 register confprof1
dspfarm profile 1 conference
description DO NOT MODIFY, active CCA conference profile - CCA2.0 codec729
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
dial-peer cor custom
name internal
name local
name local-plus
name international
name national
name national-plus
name emergency
name toll-free
dial-peer cor list call-internal
member internal
dial-peer cor list call-local
member local
dial-peer cor list call-local-plus
member local-plus
dial-peer cor list call-national
member national
dial-peer cor list call-national-plus
member national-plus
dial-peer cor list call-international
member international
dial-peer cor list call-emergency
member emergency
dial-peer cor list call-toll-free
member toll-free
dial-peer cor list user-internal
member internal
member emergency
dial-peer cor list user-local
member internal
member local
member emergency
member toll-free
dial-peer cor list user-local-plus
member internal
member local
member local-plus
member emergency
member toll-free
dial-peer cor list user-national
member internal
member local
member local-plus
member national
member emergency
member toll-free
dial-peer cor list user-national-plus
member internal
member local
member local-plus
member national
member national-plus
member emergency
member toll-free
dial-peer cor list user-international
member internal
member local
member local-plus
member international
member national
member national-plus
member emergency
member toll-free
dial-peer voice 1 pots
port 0/0/0
no sip-register
dial-peer voice 2 pots
port 0/0/1
no sip-register
dial-peer voice 3 pots
port 0/0/2
no sip-register
dial-peer voice 4 pots
port 0/0/3
no sip-register
dial-peer voice 5 pots
description ** MOH Port **
destination-pattern ABC
port 0/4/0
no sip-register
dial-peer voice 50 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/0
dial-peer voice 51 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/1
dial-peer voice 52 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/2
dial-peer voice 53 pots
description ** incoming dial peer **
incoming called-number ^AAAA$
port 0/1/3
dial-peer voice 54 pots
description ** FXO pots dial-peer **
destination-pattern A0
port 0/1/0
no sip-register
dial-peer voice 55 pots
description ** FXO pots dial-peer **
destination-pattern A1
port 0/1/1
no sip-register
dial-peer voice 56 pots
description ** FXO pots dial-peer **
destination-pattern A2
port 0/1/2
no sip-register
dial-peer voice 2000 voip
description ** cue voicemail pilot number **
destination-pattern 388
b2bua
session protocol sipv2
session target ipv4:10.1.10.1
voice-class sip outbound-proxy ipv4:10.1.10.1
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 6 pots
description "catch all dial peer for BRI/PRI"
translation-profile incoming nondialable
incoming called-number .%
direct-inward-dial
dial-peer voice 57 pots
description ** FXO pots dial-peer **
destination-pattern A3
port 0/1/3
no sip-register
dial-peer voice 69 pots
destination-pattern 329
port 0/0/0
dial-peer voice 300 pots
trunkgroup ALL_FX0
description Local Numbers
destination-pattern 9T
forward-digits 9
dial-peer voice 301 voip
destination-pattern 2..
session target ipv4:192.168.201.2
dial-peer voice 303 pots
trunkgroup ALL_FXO
trunkgroup ALL_FX0
description **InternationalCall**
destination-pattern 88T
dial-peer voice 304 pots
trunkgroup ALL_FX0
description *EM1*
destination-pattern 9[1-9]T
forward-digits 3
dial-peer voice 302 pots
trunkgroup ALL_FX0
description **Mobiles**
destination-pattern 9.[0-9].[0-9]......
dial-peer voice 305 pots
trunkgroup ALL_FX0
description **800-**
destination-pattern 9[0-9][0-9][0-9]T
no dial-peer outbound status-check pots
telephony-service
sdspfarm conference mute-on 111 mute-off 222
sdspfarm units 5
sdspfarm tag 1 confprof1
conference hardware
video
fxo hook-flash
max-ephones 40
max-dn 300
ip source-address 10.1.3.1 port 2000
max-redirect 20
auto assign 1 to 1 type bri
calling-number initiator
service phone videoCapability 1
service phone webAccess 0
service dnis overlay
service dnis dir-lookup
timeouts interdigit 5
system message American Center
url services http://10.1.10.1/voiceview/common/login.do
url authentication http://10.1.10.2/CCMCIP/authenticate.asp
load 521G-524G cp524g-8-1-17
load 525G spa525g-7-4-8
load 501G spa5x5-7-1-3c
load 502G spa5x5-7-1-3c
load 504G spa5x5-7-1-3c
load 508G spa5x5-7-1-3c
load 509G spa5x5-7-1-3c
time-zone 35
date-format dd-mm-yy
voicemail 388
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
hunt-group logout HLog
moh MOH2.wav
multicast moh 239.10.16.16 port 2000
web admin system name cisco secret 5 $1$iDgA$MKNi2RWfsO0KjuC82kgLJ1
dn-webedit
time-webedit
transfer-system full-consult dss
transfer-pattern 9.T
transfer-pattern .T
secondary-dialtone 9
fac standard
create cnf-files version-stamp 7960 Aug 29 2012 12:00:04
line con 0
privilege level 15
logging synchronous
no modem enable
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0 4
exec-timeout 0 0
logging synchronous
login local
transport input all
line vty 5 100
login local
transport input all
ntp master
end
Some of the output are not shown becaus it is to long I have attach the whole config for reference and any advice on how could I optimize and resolve my issues is greatly appreciated. Thanks

Nicolo - First off this stuff gets crazy sometimes. No worries about the exam. Sometimes when FXO ports go crazy it is due to battery reversal. If you go to the FXO port settings try turning battery reversal on and or off... depending on its current setting. See if that helps.
As for the 525s not registering.. These are inside the network correct? Are you connecting one directly to the UC500 with a Cat5E or Cat6 patch cable and the same thing happens? Does the MAC address on the phone match a MAC address under the EPHONE settings?
If you telnet into the UC500 can you execute a "dir" command at the CLI prompt and "CD" (change directory) into the phones folder and then the spa525g folder? Do files exist in there?
Also I only see an IP address under BVI100? This is the voice side of things what happened to the IP address under BVI1 (Data VLAN). Can you give us some information about the internal network? Cna you PING this phone system from the network? What IP address does it have?

How to install 2-port vic3 2fxs/DID and 2-port vic2 fxo on cisco 2801 router

Hello
I'm looking for information on how to install 2 newly purchased cards and keep running into dead links. The cards I bought are for a CISCO-2801-CCME/K9 with PVDM2-8, FL-CCME-25, SP Services 128F/256D cisco router:
vic3 2fxs/DID and a vic2 2fxo.
I keep finding documents on how to install these cards but all links are dead and leading to nowhere.
http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/2port_FXS_DID_VIC.html#wp1065062
The 2 documents i'm looking for are: how to install a 2-port vic2 fxo cards on cisco 2801 router and how to install 2-port vic3 2fxs/DID cards on the same 2801 cisco router.
NOTE: I've never installed these cards and am not sure if:
Does my ios support both of these cards?
and which slots do I install those in the router.
I have 4 slots like this:
slot 0: This slot only accepts VIC's ***This could be used for the vic3 2fxs/DID card correct?
slot 1: Nothing written here ****What can i install in this slot?
slot 2: This slot only accepts VIC's and WIC's ***If I buy a WIC and install here which other slot can i install my VIC2-2FXO card in ?
slot 3: Nothing written here ***What can i install in this slot?
Any chance someone can help me out with this.
Thanks very much

Ok
I was able to figure out what goes where and found out that the IOS i had c-2801-spservicesk9-mz.124-15.T10.bin with cme-full-4.1.0.2 tar didn't support the vic3 2fxs/DID card. I then found the one that works which is the c2801-spservicesk9-mz.124-22.YB5.bin.I am now able to see my new hardware interfaces. The question I have now is since the previous version ran with cme-full-4.1.0.2 tar i'm not sure if this needs to be changed since in the compatibility matrix i found this IOS c2801-spservicesk9-mz.124-22.YB5.bin to be compatible with cme-full-7.1.0.0 tar
Do i need to remove cme-full-4.1.0.2 tar and install the cme-full-7.1.0.0 tar?
If yes, i know how to install the cme-full-7.1.0.0 tar but how do i remove the other cme-full-4.1.0.2 tar file in order to be able to install the other version?
Thanks

NM-2V with VIC-FXO card

I have a 2621xm router. Can someone tell me which Network Module I need to get to support either 2 VIC-2FXO cards or 1 VIC-4FXO card. And these hardwares will be use in India so I also need to know which VIC-FXO card I need to get for India. Thank you in advance !!!
I understand the VIC-4FXO is universal but not sure of the VIC-2FXO.
Any helps will be greatly appreciated !!
Danny

Those cards work with NM-1V and NM-2V
(Currently EoS)
Customers are encouraged to migrate to the Cisco IP Communications Voice/Fax Network Modules (NM-HD-xx) and associated VICs. The Cisco IP Communications Voice/Fax Network Modules (NM-HD-1V, NM-HD-2V and NM-HD-2VE) support all the features of the current low density voice/fax network modules (NM-xV) while offering significant advantages such as higher port and channel densities and a new generation of digital signal processors (DSPs) with greater memory and processing power
This link contains the info you want.
http://www.cisco.com/en/US/products/hw/modules/ps5365/products_data_sheet0900aecd801c595e.html

About fxo and fxs poblems.

Hello all
I have a question about fxo and fxs .
My lab is very simple but have some problems.
analog phone ==> R1-Voice-GW (FXO port 0/1/0)<=====> (FXS port 0/2/1)R2-PBX ====> analog phone
My config setting as the below.
R1-Voice-GW
##phone number 1001 / FXS port 0/2/0
dial-peer voice 1001 pots
destination-pattern 1001
port 0/2/0
dial-peer voice 2001 pots
destination-pattern 2001
no digit-strip
port 0/1/0
R2-PBX
##phone number 2001 /FXS port 0/2/0
dial-peer voice 2001 pots
destination-pattern 2001
port 0/2/0
dial-peer voice 1001 pots
destination-pattern 1001
port 0/2/1
Question : I can call from 1001 to 2001 but can't call from 2001 to 1001 . Do I need to add any config on R1 or R2 ?

You need plar command on the FXO voice-port to point to the DN as FXO port will not receive the DNIS.
Chris
Sent from Cisco Technical Support iPhone App

How to check UC560 FXO Port Not Problem Question

Dear All,
We are newbie on Cisco UC560.
Our customer use Cisco UC560, ESW-520-24P and Cisco SPA 502G and 508G for their branch office replace old traditional PBX. Cisco UC560 have built-in VIC2-4FXO and VIC2-4FXS.
Our customer PSTN line connected to UC560 FXO port (1 line PSTN).
We receive report from our customer that they cannot make a call to PSTN and receive call from PSTN that connected to UC560 FXO port (on physical FXO port LED Green turn on). When the problem happen our customer has restart UC560 or shutdown FXO port from CLI.
We have do some test to our customer UC560.
- Moving PSTN line to another FXO port (example: port from 0/1/0 to 0/1/1). The result is same (cannot make call to PSTN and receive call from PSTN)
Today, We have checked on our customer UC560 via show voice port summary and found that port0/1/2 and 0/1/3 OPER status is up wihout cable connected to this port.
Our question:
- What command on UC560 to make sure FXO port on UC560 doesn't have problem?
We attach:
show tech-support voice
show tech-support
We hope you can give us information about this.
Thanks For Your Attention

Hi There,
If you cannot find the Indonesian "Disconnect Supervision" you may get away with using Singapores "Disconnect Supervision" as your carrier networks are similar to each other
Cheers,
David Trad.

How to put individual FXO trunk into a trunk group

I have a 3725 with 2 vic2-4fxo cards configured as H.323 in ccm 4.0.2a. Currently I have to configure 8 pots dial peers to point to each fxo port for outbound call. I would like to find out if there is a way set up like a trunk group for fxo that way I just need one pots dial peer and point it to the trunk group instead of 8 seperate dial peers pointing to each port. Kinda like route group and route list in ccm.
Can someone help ?
Thanks in advance !!!
Danny

Danny,
Please see following website:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123tcr/123tvr/vrht_t3.htm#wp1622963
1. create trunk-group (voice port) assign to voice-port interface.
2. then create trunk-group-label (dial-peer) assing to dial-peer level.
please rate the helpful post
Ken

Detect Fax Tone on FXO & Route to FXS?

Can the UC320W detect a fax tone on an FXO line and automatically route that call to the FXS port?
Thanks,
Mike

Hi Wenjin (Wendy),
I have three (3) dedicated FXO lines for voice and one (1) FXO line dedicated and directly connected to the Fax machine.
I was trying to get a little adventurous and see if I could utilize all four FXO lines into the UC320W and the phone service provider's hunt function to use, in the event of a 4th incoming voice call, the fax phone number (4th FXO line) thus getting a much better utilization factor on that 4th FXO line. This would only work if the UC320W could be configured to detect a fax tone on that 4th FXO line and subsequently direct it to the FXS port where the fax machine could be connected.
Essentially, I was hoping to be able to utilize all FXO lines to their "full capacity". As you know very few people send faxes anymore (mostly scan attachments to emails) resulting in two things: a) my dedicatated FXO fax line rarely ever gets used (poor payout); and, b) as the business grows and I could use that 4th FXO line, I can't so I'm forced into a different phone service provider connection type (SIP?).
Do you know if Cisco is considering a FXO to FXS fax detection and direction functionality modification to the firmware (if hardware permissible of course)?
Ever so much appreciated.
Thanks,
Mike

Connecting FAX to PSTN line using FXS and FXO ports

I have 2 cisco 1760 routers with FXS and FXO card installed in each. I have to transport 2 PSTN lines from Head Office to remote loaction using FXS and FXO cards and these lines will be used for voice calls and FAX( one line each for FAX and voice). I have configured the router for voice lines and it is working fine. Now I am using the same config for running fax machine but it is not working. Can anyone help me out how to configure FAX in this scenario also if anyone can share any sample config. I am attaching my config for both routers. Right now both routers are connected with a cross-over cable for lab test but we will connect them later using satellite connection.
HO Router (FXO card)
Current configuration : 1718 bytes
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable password cisco
no aaa new-model
resource policy
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
voice-card 2
voice-card 3
ip subnet-zero
ip cef
no ip dhcp use vrf connected
no ip domain lookup
no ftp-server write-enable
voice class codec 10
interface FastEthernet0/0
ip address 10.10.10.1 255.255.255.248
speed auto
h323-gateway voip bind srcaddr 10.10.10.1
ip classless
no ip http server
control-plane
voice-port 2/0
output attenuation 0
echo-cancel coverage 32
no vad
no comfort-noise
timeouts interdigit 3
timeouts call-disconnect 3
connection plar opx 2001
description Remote PSTN#:35296913
music-threshold -70
voice-port 2/1
output attenuation 0
echo-cancel coverage 32
no vad
no comfort-noise
timeouts interdigit 3
timeouts call-disconnect 3
connection plar opx 2002
description Remote PSTN#:35296914
music-threshold -70
voice-port 3/0
voice-port 3/1
dial-peer voice 2000 voip
destination-pattern 200.
no modem passthrough
voice-class codec 10
session target ipv4:10.10.10.2
incoming called-number .
dtmf-relay cisco-rtp h245-signal h245-alphanumeric
fax-relay ecm disable
fax rate 7200
fax nsf 000000
no vad
dial-peer voice 1321 pots
description line 1
huntstop
destination-pattern 1321
port 2/0
dial-peer voice 1322 pots
description line 2
huntstop
destination-pattern 1322
port 2/1
line con 0
password cisco
line aux 0
line vty 0 4
password cisco
login
end
Remote Router (FXS Card):
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable password cisco
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
voice-card 2
voice-card 3
no aaa new-model
ip subnet-zero
ip cef
no ip domain lookup
no ftp-server write-enable
voice class codec 10
interface FastEthernet0/0
ip address 10.10.10.2 255.255.255.248
speed auto
h323-gateway voip bind srcaddr 10.10.10.2
interface Ethernet1/0
no ip address
shutdown
half-duplex
ip classless
no ip http server
control-plane
voice-port 2/0
description PSTN#:
voice-port 2/1
description PSTN#:
voice-port 3/0
voice-port 3/1
dial-peer voice 2001 pots
description Remote
huntstop
destination-pattern 2001
port 2/0
dial-peer voice 2002 pots
description Remote
huntstop
destination-pattern 2002
port 2/1
dial-peer voice 1320 voip
destination-pattern 132.
no modem passthrough
voice-class codec 10
session target ipv4:10.10.10.1
incoming called-number .
dtmf-relay cisco-rtp h245-signal h245-alphanumeric
fax-relay ecm disable
fax rate 7200
fax nsf 000000
no vad
line con 0
password cisco
line aux 0
line vty 0 4
password cisco
login
end

In your voice class codec 10 there aren't any codecs declared.
Add G.711 codec in this way:
voice class codec 10
codec preference 1 g711alaw
If the fax communication fails again try to disable T.38 and try fax passthrough mode:
no fax rate
modem passthrough nse codec g711alaw
fax protocol pass-through g711alaw
Regards.

Incorrect Caller ID on calls from outside line via FXO port.

   Have a public phone line connected to my CUCME 2801 router VIC2-2FXO card. All inbound calls are passed to DN-5001 (group number). Can receive and send calls without a problem, but incoming calls all show "911" for caller ID. Think this is simply an issue with the out bound dial-peer, of which the lowest numbered out bound dial-peer is for 911 services. Not sure how to correct this so inbound calls show the proper caller ID?
    Below is a copy of my CUCME show run output from the FXO port config thru all the dial-peers. Any pointers is greatly appreciated.
    Thanks.
           Kirk E.
voice-port 0/0/0
connection plar opx immediate 5001
voice-port 0/0/1
voice-port 0/2/0
station-id name POTS
station-id number 7000
voice-port 0/2/1
ccm-manager config
dial-peer voice 7000 pots
destination-pattern 5006
port 0/2/0
dial-peer voice 90 pots
description Emergency Services
destination-pattern 911
port 0/0/0
forward-digits 3
dial-peer voice 91 pots
description 10 Digit local dialing
destination-pattern [234].........
port 0/0/0
forward-digits 10
dial-peer voice 92 pots
description 11 Digit local/long distance dialing
destination-pattern 1[2348].........
port 0/0/0
forward-digits 11
dial-peer voice 93 pots
description Long Distance
destination-pattern 011T
port 0/0/0
prefix 011
dial-peer voice 94 pots
description Backup bench POTS phone
destination-pattern 7000
port 0/2/0
dial-peer voice 2 voip
destination-pattern 51..
session protocol sipv2
session target ipv4:172.16.2.155
dtmf-relay sip-notify
codec g711ulaw
no vad

Hi
Can you find the below:-
Hi
1- Please find the below table as the following link http://www.cisco.com/en/US/products/hw/routers/ps274/products_tech_note09186a00800b53c7.shtml
Caller ID          Requires VIC-2FXO-M1, VIC-2FXO-M2, VIC-4FXO-M1, VIC2-2FXO, VIC2-4FXO, or MRP3-8FXOM1
under voice-port
caller-id enable
2-If above configure and still have no caller id , please add the below commannds to the voice-port
caller-id alerting line-reversal
cptone ?               "based on your"
caller-id alerting ring 2    "the default is 1" maximum number of rings to be detected before a call is answered over an FXO voice port.
4-Do debug to make sure all ok
"debug vpm signal "
[0/3/0] get_fxo_caller_id:Caller ID received. Message type=128 length=31 checksum=74
Thank you
please rate all useful information

CME fxo port problem

hi,
I have a 2801 CME and 2 fxo lines. Some times when both lines are seized (because of incoming and outgoing call) and after the phones are on hook the lines are still seized and are not released and when i removed the cables from fxo port, the led on each port start to blink in sequence and then when i reconnected, the port was busy again.. so i had to reboot the router to make it work. i changed the slot but dont think that it will cause any difference..do i need to upgrade the ios or some other issue..when i am calling the disconnect is fine but it happens some time when the line get stuck i have to reboot the router. one more thing when i changed the slot of the card the router didnt detected the change of slot and was showing fxo port on old slot. i rebooted the router to detect the fxo card on the right slot..sorry for the double post but no body was replying to i post it again..
Currently Being Moderated
May 12, 2012 11:49 AM (in response to Naresh Rathore)
FXO lines stuck/hang (2801 CME)
hi following is the sh run and sh version. cme output portion is removed
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.02.03 14:27:39 =~=~=~=~=~=~=~=~=~=~=~=
User Access Verification
Username: admin
Password:
Router_Home>en
Password:
Router_Home#term
Router_Home#terminal le
Router_Home#terminal length n   512
Router_Home#sh run
Building configuration...
Current configuration : 15203 bytes
! Last configuration change at 14:41:02 UTC Thu Feb 3 2011 by admin
! NVRAM config last updated at 14:38:09 UTC Thu Feb 3 2011 by admin
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router_Home
boot-start-marker
boot-end-marker
enable password cisco
no aaa new-model
clock calendar-valid
crypto pki trustpoint TP-self-signed-2416845307
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2416845307
revocation-check none
rsakeypair TP-self-signed-2416845307
crypto pki certificate chain TP-self-signed-2416845307
certificate self-signed 01
30820243 308201AC A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32343136 38343533 3037301E 170D3131 30323032 31373332
34335A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D32 34313638
34353330 3730819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100DFAC E4312F46 0F2BF242 E55FE0C1 73DC95F2 B2844295 DA691CE3 D9A202B1
77B1B0C3 5AE3D936 C4D786DB 7CFA6624 024C6A82 A29B3AAC 3BA89A77 5425A97A
6D79A88A C1327171 C88AA5E0 AB52F461 87FB472E A7622955 17C8F22C 58842EF4
4DFA422A 54E6B96A FA536C59 BD93FDCD 872C0586 08117535 2D13F1E0 A53E65AB
FE470203 010001A3 6B306930 0F060355 1D130101 FF040530 030101FF 30160603
551D1104 0F300D82 0B526F75 7465725F 486F6D65 301F0603 551D2304 18301680
14E940B0 E437790B 4B825CD2 0FA9020F 63C9ED3A ED301D06 03551D0E 04160414
E940B0E4 37790B4B 825CD20F A9020F63 C9ED3AED 300D0609 2A864886 F70D0101
04050003 8181006B D6136D19 6EF4DDCD B3AF591E 57B9B831 79578799 03862FCF
4AF772DE AC72FC85 3F6B6B20 81F528F0 F7B2CBD0 E9795060 C46AB102 AE2CDF53
11C39D67 B49A7AE8 FB619A0F 525543F7 8BA1D52C CABEFFEB 9E5EC7E7 938AA602
84F1ECD2 303E8609 A9AB0699 9078051B 1853BC9A 4B45F2A2 204310D5 8B34B5DD
2FA51064 EFF5D4
   quit
dot11 syslog
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.168.0.1
ip dhcp excluded-address 10.168.0.2
ip dhcp excluded-address 10.168.10.1
ip dhcp excluded-address 10.168.10.2
ip dhcp excluded-address 10.168.111.1 10.168.111.6
ip dhcp pool Data
   network 10.168.0.0 255.255.255.0
   default-router 10.168.0.1
   option 150 ip 10.168.10.1
   dns-server 212.72.1.186 212.72.23.4
ip dhcp pool VOICE
   network 10.168.10.0 255.255.255.0
   default-router 10.168.10.1
   option 150 ip 10.168.10.1
ip dhcp pool WLAN
   network 10.168.111.0 255.255.255.0
   default-router 10.168.111.1
   option 150 ip 10.168.10.1
   dns-server 212.72.1.186 212.72.23.4
ip host members.dyndns.org 204.13.248.112
ip name-server 212.72.1.186
ip name-server 212.72.23.4
ip ddns update method example_dyndns
HTTP
add http://whatisthis:[email protected]/nic/update?system=dyndns&hostname=<h>&myip=<a>
interval maximum 28 0 0 0
interval minimum 28 0 0 0
multilink bundle-name authenticated
voice-card 0
dsp services dspfarm
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
no supplementary-service h450.2
no supplementary-service h450.3
supplementary-service h450.12
h323
sip
registrar server expires max 600 min 60
username xxxxx password 0 xxxx
archive
log config
hidekeys
interface FastEthernet0/0
no ip address
ip nat inside
ip virtual-reassembly
speed auto
full-duplex
no keepalive
interface FastEthernet0/0.2
description ***** Voice LAN ******
encapsulation dot1Q 2
ip address 10.168.10.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/0.3
description ***** Data LAN ******
encapsulation dot1Q 3
ip address 10.168.0.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/0.4
description ***** Wireless LAN ******
encapsulation dot1Q 4
ip address 10.168.111.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface FastEthernet0/1
description $ES_WAN$
no ip address
shutdown
duplex auto
speed auto
interface ATM0/1/0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
interface ATM0/1/0.1 point-to-point
pvc 0/35
pppoe-client dial-pool-number 1
interface Dialer0
no ip address
interface Dialer1
mtu 1492
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1452
ip nat outside
ip virtual-reassembly
encapsulation ppp
ip route-cache flow
ip tcp adjust-mss 1412
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname xxxx
ppp chap password 0 xxxxx
ppp pap sent-username xxxx password 0 xxxxx
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer1
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip dns server
ip nat inside source list 101 interface Dialer1 overload
ip nat inside source route-map NAT_RMAP interface Dialer0 overload
access-list 101 permit ip 10.168.0.0 0.0.0.255 any
access-list 101 permit ip 10.168.111.0 0.0.0.255 any
route-map NAT_RMAP permit 10
match ip address 101
control-plane
voice-port 0/0/0
supervisor disconnect dualtone mid-call
input gain 14
compand-type a-law
cptone BE
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 121
impedance complex2
caller-id alerting dsp-pre-allocate
voice-port 0/0/1
supervisor disconnect dualtone mid-call
input gain 14
compand-type a-law
cptone BE
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 121
impedance complex2
caller-id alerting dsp-pre-allocate
voice-port 0/0/2
supervisor disconnect dualtone mid-call
input gain 14
compand-type a-law
cptone BE
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 121
impedance complex2
caller-id alerting dsp-pre-allocate
voice-port 0/0/3
supervisor disconnect dualtone mid-call
input gain 14
compand-type a-law
cptone BE
timeouts call-disconnect 5
timeouts wait-release 5
connection plar opx 121
impedance complex2
caller-id alerting dsp-pre-allocate
dial-peer cor custom
name local
name longdistance
dial-peer cor list call-local
member local
dial-peer cor list call-longdistance
member longdistance
dial-peer cor list manager
member local
member longdistance
dial-peer cor list other
member local
dial-peer voice 1 pots
corlist outgoing call-longdistance
destination-pattern 0.T
port 0/0/0
dial-peer voice 2 pots
corlist outgoing call-longdistance
destination-pattern 0.T
port 0/0/1
dial-peer voice 3 pots
corlist outgoing call-longdistance
destination-pattern 0.T
port 0/0/2
dial-peer voice 4 pots
corlist outgoing call-longdistance
destination-pattern 0.T
port 0/0/3
dial-peer voice 5 pots
corlist outgoing call-local
destination-pattern 0[2,9].......
port 0/0/0
dial-peer voice 6 pots
corlist outgoing call-local
destination-pattern 0[2,9].......
port 0/0/1
dial-peer voice 7 pots
corlist outgoing call-local
destination-pattern 0[2,9].......
port 0/0/2
dial-peer voice 8 pots
corlist outgoing call-local
destination-pattern 0[2,9].......
port 0/0/3
dial-peer voice 9 pots
corlist outgoing call-local
destination-pattern 0800T
port 0/0/0
prefix 800
dial-peer voice 10 pots
corlist outgoing call-local
destination-pattern 0800T
port 0/0/1
prefix 800
dial-peer voice 11 pots
corlist outgoing call-local
destination-pattern 0800T
port 0/0/2
prefix 800
dial-peer voice 12 pots
corlist outgoing call-local
destination-pattern 0800T
port 0/0/3
prefix 800
telephony-service
no auto-reg-ephone
max-ephones 25
max-dn 25
ip source-address 10.168.10.1 port 2000
auto assign 1 to 20
timeouts interdigit 5
system message Home
max-conferences 8 gain -6
call-forward pattern .T
dn-webedit
transfer-system full-consult dss
transfer-pattern .T
ephone-dn 1 dual-line
number 101
label M.M Office (101)
description M.M Office (101)
name M.M Office
ephone 1
device-security-mode none
video
mac-address 1C17.D3C3.7A31
speed-dial 1 102 label "abc"
speed-dial 2 103 label "def"
speed-dial 3 104 label "hij"
speed-dial 4 113 label "klm"
speed-dial 5 104 label "nop"
speed-dial 6 105 label "qrst"
speed-dial 7 105 label "uvw"
type 7975
button 1:1 2:21
ephone-hunt 1 sequential
pilot 150
list 121
line con 0
exec-timeout 0 0
logging synchronous
login local
line aux 0
line vty 0 4
login local
transport input telnet
scheduler allocate 20000 1000
ntp master 2
ntp update-calendar
end
Router_Home#sh di
Router_Home#sh dia
% Ambiguous command: "sh dia"
Router_Home#sh ds
Router_Home#sh dsv   p
Router_Home#sh dspfarm
% Incomplete command.
Router_Home#sh dspfarm ?
all      Display all DSPFARM global info
dsp      Display DSPFARM DSPs information
profile Display DSPFARM profiles
Router_Home#sh dspfarm ds
Router_Home#sh dspfarm dsp
% Incomplete command.
Router_Home#sh dspfarm dsp             all
Total number of DSPFARM DSP channel(s) 0
Router_Home#sh ver
Router_Home#sh version
Cisco IOS Software, 2801 Software (C2801-ADVIPSERVICESK9-M), Version 12.4(15)T10, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 14-Sep-09 14:51 by prod_rel_team
ROM: System Bootstrap, Version 12.3(8r)T9, RELEASE SOFTWARE (fc1)
Router_Home uptime is 21 hours, 11 minutes
System returned to ROM by power-on
System restarted at 17:31:27 UTC Wed Feb 2 2011
System image file is "flash:c2801-advipservicesk9-mz.124-15.T10.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 2801 (revision 6.0) with 237568K/24576K bytes of memory.
Processor board ID FCZ10491208
2 FastEthernet interfaces
1 ATM interface
2 Virtual Private Network (VPN) Modules
4 Voice FXO interfaces
1 DSP, 8 Voice resources
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
62720K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
Router_Home#exit
Regards

Actually this has been answered already:
https://supportforums.cisco.com/thread/2148571?tstart=0
please do not open duplicate threads. You can delete you post using the Actions panel on the right.

FXO-to-FXO

Similar Messages

Maybe you are looking for