FXS/Analog phone auto-dial when picked up?

Hello. UC540 862. I have a door intercom i have patched into the phone system via FXS port (will not use FXO). When the button is pressed on the door intercom, you get a dial tone over the speaker and the FXS port is open. Is there a method to have it auto-dial an extension? I've setup lobby phones that intercom a specific phone internally, but in this case, i need it to autodial a main hunt group- ext 101, which blasts 4 people. Unfortunately the door unit does not have a dial-pad.
Thanks in advance.

didn't work but again - fxs port as it's not compatible with fxo port .. (below readout).. trying connection plar 101.. maybe that'll work
KMK-UC540(config-voiceport)#do show voice port sum
                                           IN       OUT
PORT            CH   SIG-TYPE   ADMIN OPER STATUS   STATUS   EC
=============== == ============ ===== ==== ======== ======== ==
0/0/0           -- fxs-ls      up    dorm on-hook idle     y
KMK-UC540(config-voiceport)#voice-port 0/0/0
KMK-UC540(config-voiceport)#intercom 101
                              ^
% Invalid input detected at '^' marker.
KMK-UC540(config-voiceport)#int ?
% Unrecognized command
KMK-UC540(config-voiceport)#

Similar Messages

FXS analog phone can't break dial tone when pressing some number keys.

Hi All,
May I know how to break the dial tone when pressing any keys? I've tried to set the input gain to 0 dB, -1dB, -4dB and 4dB but same results.
Voice-port also configured in "timeouts interdigit 3". In other sites, same configured but it is working.
Is it defective or need to be configured?
Highly appreciated for your response.
Thank you
Regards,
RJ

Thanks for the reply Paolo.
VIC3-2FXS/DID, and RJ-11 for phone.
config:
voice-port 0/1/0
timeouts interdigit 3
I also tried to add input gain like I said on my post. But its not works.
Thanks and Best regards,
RJ

I phone auto starts when i plug into usb in car

the I phone music starts playing when i just plug the phone into the USB port in the car. How do i stop that. is it a car software issue or an iphone issue?

Hey there MORGRM,
It sounds like your phone just starts playing music automatically every single time you connect it to the USB port in your vehicle. We should be able to troubleshoot the software on the phone to help you isolate it to the phone or the vehicle. Start by quitting the running apps on your phone with this article:
iOS: Force an app to close
Double-click the Home button.
Swipe left or right until you have located the app you wish to close.
Swipe the app up to close it.
When you have done that restart the phone and test the issue again:
iOS: Turning off and on (restarting) and resetting
Thank you for using Apple Support Communities.
Regards,
Sterling

Auto dial-up

Hello,
Wow, it's been a while since I've been here. Had to create a whole new ID.
Anyway, I got a new iMac G5 last week and phone support helped me figure out how to transfer files from my old Bondi RevB, OS/9.2.2---which is the one I'm having the current problem with.
Problem is now everytime I turn the Bondi back on it automatically dials up the internet. ie., I started it up this morning and didn't come back to the computer for about two hours and all that time it was dialed up and I didn't realize it.
Went to Control Panels>Remote Access>Options>Protocol and un-checked "Connect automatically when starting TCP/IP applications." That stopped it from dialing up when starting the computer, but it also stopped it from dialing (automatically) when launching Internet Explorer.
Bottom line...how can I make it so that it does not dial-up when turning the computer on, BUT will auto dial when launching IE.
As always, Thanks in advance.
P.S. Haven't been able to work too much with the new iMac, but it sure is "purty".

Neil,
Yes indeed, there was an HD alias in there. Thank you so much for the info. I've already trashed it. I'll let you know later whether or not that does the job---I really don't know what else I haven't investigated that could be the culprit. If this does solve the problem, do you know whether I will have to delete the alias each time after I file share?...or do I just have to wait and see?
I have a bit of surfing and work to do, so I don't want to log off and try it now, but I will definitely post back later tonight or tomorrow and let you (all) know.
Thanks again, Neil.

My iphone has a problen on the phone icon. When I press the phone icon, it will auto dial the last number, how can I fix this?

my iphone has a problen on the phone icon. When I press the phone icon, it will auto dial the last number, how can I fix this?

Try This...
Close All Open Apps... Perform a Reset... Try again...
Reset ( No Data will be Lost )
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
http://support.apple.com/kb/ht1430

MWI on analog phone using stutter dial on VG248

Someone is telling me that you can use stutter dial or some other method to light up an anolog phone Message waiting indicator using on a VG248. This is with an analog phone that has an Message light on it. Is this possible and if so is it possible using and ATA with Call Manager?

Hi Shane,
This does work with the VG248, we have used the "Stutter Dial Tone" on some analog phones and used the actual MWI Lamp on other analog phones with good success. Have a look;
Choosing Message Waiting Indicator Type
The VG248 supports several types of methods for sending MWI messages to analog phones. Because you might have different types of analog phones connected to the VG248, you can modify the MWI type on a per-port basis. So, if you have some analog phones that have MWI lamps on them, you can notify users of awaiting messages using the lamp. Or, you can choose to play a tone when users pick up their phones.
Keep in mind that the VG248 only sends this information to the phones if it is received from Cisco CallManager. If Cisco CallManager is not integrated with your voice mail system, it does not send this information to the VG248.
Step 1 From the main menu, choose Configure.
Step 2 Choose Telephony.
Step 3 Choose Port specific parameters.
Step 4 Use the arrow keys to select the port to configure and press Enter.
Step 5 Choose MWI type.
Step 6 Choose from the following options:
Lampilluminates lamp on phone
Caller IDuses caller ID mechanism to send MWI messages to the LCD screen on phone
Stutterplays tones when user picks up the phone
Lamp + stutterilluminates lamp and plays tone
Caller ID + stuttersends message to LCD screen and plays tone
Nonedoes not send MWI information
From this doc;
http://www.cisco.com/en/US/products/hw/gatecont/ps2250/products_configuration_guide_chapter09186a0080087de4.html#xtocid13
Hope this helps!
Rob
Please remember to rate helpful posts..........

Pick up group between analog Phone connected on VG224 with Cisco 7911 does not work?

Hey guys,
I had a problem, during a demo. My team was design a cisco callmanager 7.0 with 7911 IP Phone and with VG224 analog devices phones. I would like to know if there are some a problem of capability when configured a Analog Phone on VG224 in the same pickup group with Cisco IP Phone 7911.
I got pickup between Analog phones but with I cannot pick up, between IP Phones and analog phones.
Does anybody knows if has capability problem or could be a configuration problem.
The feature has already enbled for pick up **3 (stcapp feature access-code).
best regards
Daniel

Hi Daniel,
Did you try **4
The default settings for the VG224 feature codes are as follows:
Call Forward All (CFA) **1
Call Forward All Cancel **2
Call Park Directed Call Pickup Directed **6
Call Pickup Group **4
Call Pickup Local **3
Call Transfer = Hookflash
Redial *#
Speed Dial *01 to *99 for two-digit codes
Speed Dial to Voice Mail Default prefix and code is *0 for one-digit codes, and *00 for two-digit codes
http://www.cisco.com/en/US/docs/ios/12_4t/12_4t2/ht1vg224.html#wp1178205
Hope this helps!
Rob

Analog door phone to dial phones configuration

I have a remote office that I'm trying to setup CME. Everything works for now except one thing. There is a analog phone installed on outside of front door for visitors, deliveries, etc. Trying to setup this phone to ring automatically reception desk and also enable for others to answer the line from their phone when there is no one available in the reception area. I was thinking of connecting this door phone to one of the FXS ports on the router and configure PLAR to ring reception desk phone. Any suggestion? how do I setup other phones to be able to answer/pick up when no one at the reception desk? Pickup group? Thanks.

Thanks for your reply kkoeper12. I have configured the following. Did I get this right? I really can't test it at the moment. Just want to check first. Thanks.
voice hunt-group 1 sequential
final 2212
list 2212,2211,2213,2214,2202,2203,2204,2205
timeout 30
pilot 2227
voice-port 0/2/0 ---- this is where I have a analog door phone connected.
connection plar 2227
ephone-dn 26 dual-line
number 2227

Vg224 don't auto disconnect with analog phone

Dear all ,
why vg224 don't auto disconnect with analog phone? is the busy frequency dismatch between vg224 and analog phone?
can you have any suggest to me ?
thks.

HI rrjoas45,
thks your answer, I try to add a command with supervisory . but I discovery it isn't effective . the port status follow:
sh voice port 2/0
Foreign Exchange Station 2/0 Slot is 2, Port is 0
Type of VoicePort is FXS
Operation State is DORMANT
Administrative State is UP
The Last Interface Down Failure Cause is Administrative Shutdown
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Non Linear Mute is disabled
Non Linear Threshold is -21 dB
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancellation NLP mute is disabled
Echo Cancellation NLP threshold is -21 dB
Echo Cancel Coverage is set to 64 ms
Echo Cancel worst case ERL is set to 6 dB
Playout-delay Mode is set to adaptive
Playout-delay Nominal is set to 60 ms
Playout-delay Maximum is set to 250 ms
Playout-delay Minimum mode is set to default, value 40 ms
Playout-delay Fax is set to 300 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call Disconnect Time Out is set to 60 s
Supervisory Disconnect Time Out is set to 750 ms
Ringing Time Out is set to 180 s
Wait Release Time Out is set to 30 s
Companding Type is u-law
Region Tone is set for CN
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Analog interface A-D gain offset = -3.0 dB
Analog interface D-A gain offset = -3.0 dB
FXS idle voltage set to high
Ring DC offset set to 0 volt
Station name None, Station number None
Translation profile (Incoming):
Translation profile (Outgoing):
Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is active
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Hookflash-in Timing is set to max=1000 ms, min=150 ms
Hookflash-out Timing is set to 400 ms
No disconnect acknowledge
Ring Cadence is defined by CPTone Selection
Ring Cadence are [10 40] * 100 msec
Ringer Equivalence Number is set to 1
thks.

I can turn my phone on only when connected to power. however it cant pick up signal it says connect to apple/support but I cant plug in to computer as it needs power I think the battery aerial is stuffed can I still backup phone if i put into get repaired

can turn my phone on only when plugged into the power. everything is still accessable on the when when this is done. but it cant pick up a signal its just serching.
a message says i need to connect to apple/support but i can plug into the computer as its not getting any power and i cant turn on.
I need pictures and stuff baked up on it as i dont want to loose them.
I think the battery/aerial in stuffed as it go some water on it.
will it be possible to save the data when getting repaired???

Hello there stidhambr15,
I was researching the issue you are having and recommend a couple of things. First it might be a good idea to reset the device following iPhone, iPad, iPod touch: Turning off and on (restarting) and resetting found here http://support.apple.com/kb/ht1430
Resetting your device
Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
If that doesn't quite get the device going again, I recommend restoring the device.
iTunes: Restoring iOS software
http://support.apple.com/kb/ht1414
Might even be a good idea to turn off the phone, reseat the SIM card, and turn it back on.
iPhone and iPad: How to remove the SIM card
http://support.apple.com/kb/ht5163
iPhone 4 (GSM model)
iPhone 4S
Cheers,
Sterling

Phone Stops Ringing When I pick it Up

Hello
I have a Blackberry 9720.
1. I want to find out why my phone stops ringing when I pick it up to answer it?
2. How can I get it ring for longer as it rings for such a short time?
Many thanks
Barbara
Solved!
Go to Solution.

Barbara,
1- I'm not sure why this is happening but reloading your OS using BlackBerry Desktop Software should correct this. To reload your OS, plug your phone in to BDS on your PC and click Device at the top of BDS then click Backup. Once you've done a backup, click Device once again but this time click Restore and choose the file you just created and load it. If you had a touchscreen, I'd suggest that you're probably touching the screen which would cancel the ringtone but because your phone is not a touchscreen, this wouldn't apply.
2- Call MTN for help with this issue. It's your carrier that controls for how long your phone rings and they can set it to go as long as 30 seconds if you request it.
I hope that helps you.
- If my response has helped you, please click "Options" beside my post and mark it as solved. Clicking the "thumbs up" icon near the bottom of my response would also be appreciated.

Auto-Dial from SIP phones after Interdigit Timeout

I have a customer that needs to have their phones automatically dial a particular number if no digits are pressed after 10-15 seconds. We are accomplishing this right now with our SCCP phones by having a blank translation pattern that points to an ambiguous hunt pilot.
For example, we create a blank translation pattern that translates to a HP with number 300. We also create a HP with number 3000. The translation pattern is triggered, but because 300 is ambiguous (the call could possibly be destined for 300 or 3000) CUCM waits for the interdigit timeout before calling 300.
This works beautifully for SCCP phones. Unfortunately, it does not work for our SIP phones. Does anyone have any suggestions to make this work? SIP dial rules trigger immediately, so I'm afraid we haven't been able to leverage those.
Thank You!

Thanks for your comments, but I'm afraid you guys are missing the issue.
Chris, you are correct that you can get a SIP phone to auto-dial a number via SIP dial rules. The problem is that it triggers immediately. I need the SIP phones to wait.
Here's a scenario - SCCP phones are in use all throughout a nursing home. Residents are told that they can simply knock their phone offhook if they need emergency help. If they don't dial anything within 15 seconds, their phone will automatically call into the local emergency oncall nurse. Sorta an "onstar" emergency help line for an old folks home. We definitely can't have that rule triggering immediately though, as residents would never be able to place a normal call, and there would be no way of distinguishing the emergency calls from the guy who is just trying to call for pizza. :)
This function works perfectly with SCCP phones - while they trigger the blank translation pattern immediately, CUCM doesn't actually begin dialing because there are multiple potential matches for what the translation pattern is dialing. SIP phones do not do this, however. If you have the SIP dial rule applied, it always triggers immediately, and it does not wait to see if callers give any input.
Thanks for any further suggestions you might be able to offer!

How do I change which phone number from a contact will be dialed when I push a favorite in phone?

How do I change which phone number from a contact will be dialed when I push a favorite button in phone? For example if a favorite dials a contact's office number and I want their cell to be called instead.

Thanks again Chris.
I was simply going to write that you were incorrect and there are no plus signs either, but I was certian you knew what was supposed to happen, and that I wasn't going soft either. So after staring at it for a while it just came to me: the file was full! I deleted just one favorite and both the plus and the Add to Favorites button appeared where you described.
Thanks for your help,
Larry

Why do I mute or dial when talking on the phone? I used to not have any problems.

Why do I mute or dial when talking on the phone? Previously I did not have an issue. The phone seems very sensitive

The proximity sensor might have failed on your phone. That's what forces the phone to dim the screen when you bring it up to your face.

Can't transfer to an analog phone on FXS port (CME2811)

I have six IP phones with locals 501 to 506. Additionally, I have four analog phones (locals 541 to 544) connected to a VIC2-4FXS card on a 2811 with CME and CUE module.
All phones can call each other. But if say, a user on an IP phone calls a 2nd user on another IP phone, the 2nd user cannot transfer to the 54x locals. She hears a busy or reorder tone (still need to verify which) after keying in the 2nd digit (ie. 54 then "busy" tone)
Am I missing something?

Under telephony-service configuration enter the transfer-pattern command. For example:
router(config)#telephony-service
router(config)#transfer-pattern 5..
If no transfer pattern is set, transfers are only permitted to other IP phones.
Hope this helps. If so, please rate the post.
Brandon

FXS/Analog phone auto-dial when picked up?

Similar Messages

Maybe you are looking for