FYI: "Sub-technology" selections for UCCE/UCCX TAC Service Requests will be updated soon

Hello, Cisco Contact Center customers and partners.
I'm happy to report that the "Sub-Technology" selections listed under the "Contact Center Software" Technology for TAC Service Requests will be updated with the proper names of the Contact Center products soon. This change is scheduled to take effect Monday Oct 10.
The major changes are as follows:
- References to "IPCC Enterprise" will be replaced with "UCCE/Contact Center Enterprise"
- References to "IPCC Express" will be replaced with "UCCX/Contact Center Express"
- Separate UCCE CUIC and WebView sub-techs will be consolidated into one Reporting sub-tech
- Removal of the redundant "CVP Product" sub-tech ("Unified CVP" will be retained)
- Addition of new "Contact Center Management Portal (CCMP)" and "Remote Silent Monitoring (RSM)" sub-techs for UCCE
And just as a general note, when opening a Service Request for any technology via Cisco.com, please be sure to provide all the relevant details, so that we can route your issue to the best available TAC engineer. Always include:
- full product name
- full product version
- detailed description of the problem/symptoms, including the scope of the issue and the frequency
- the business impact of the problem
- the date/time the problem started happening, and what changed around that time
- call flow (if applicable)
- any recent upgrades, major changes, outages, or other existing problems
- any logs, data, or screenshots that were captured
Thank you!
-Paulo

Similar Messages

Cisco Prime unable to connect to TAC Service Requests

Always had the problem, but now decided to mess around with it.
When I try to get Cisco Prime 4.1 to connect to TAC Service Request I get the following error....
"There was an error while fetching the list of TAC Service Requests: String index out of range: -1"
I am able to download IOSs and other software with Prime, just not able to connect to TAC.
Thanks

Hi Marco,
actually it took me quite a long time to understand what the problem was. I found that on my CISCO AP i had to put "payload-encapsulation dot1h" on the radio interface to get the WIP310 communicate with the AP.
By the way It seems to me that the phone is a little buggy from the wireless point of view. Sometimes i have to try several times before getting the phone connected to the AP. Once the phone gets connected it's pretty stable, but getting it connected it's a nightmare :-)
Try with the above ption if you have a Cisco AP. Also try different channels on the AP...it might help
Hope this will help you
regards
Nicola

Apple software update for itunes version 11.0.1 will not update

apple software update for itunes version 11.0.1 will not update says invalid signature and will not be installed? how do i fix this?

apple software update for itunes version 11.0.1 will not update says invalid signature and will not be installed? how do i fix this?

Alert for status changed in Service request CRM

Dear All,
We have a requirement where if the status is changed for a service request, an alert should appear in the context area of the interaction center warning the user of this modification.
I have tried to used the Alerts Configuration in the business role of IC_MANAGER to do this, can i do this only with customizing or do i need any development?
Thanks for all your input.
Best Regards,
João Gaifém

Hi,
As no standard event is raised when changing the status, you could do the following.
Create a Z event (in SPRO, Customer Relationship Management->Interaction Center WebClient->Additional Functions-> Intent-Driven Interactions Define Events in Repository).
Then, you could enhance the view in which the status is managed.
If you want the alert to be shown when selecting the status, create an event handler for the attribute (if not existing already).
In this event handler, call the Z event you just created.
The code should look like :
DATA : lr_event TYPE REF TO cl_crm_ic_event,
lr_event_srv TYPE REF TO if_crm_ic_event_srv.
CREATE OBJECT lr_event.
lr_event->set_name( 'ZSTATUS_CHANGED' ). “Name of event created
lr_event_srv = cl_crm_ic_services=>get_event_srv_instance( ).
lr_event_srv->RAISE( lr_event ).
Then, create your own IDI rule, so that when the Z event is raised, an alert should be displayed.
Hope this can help you.
Sylvain

SAP Cloud For Customer : Integration of Service Request to CRM Issue

Hello Team,
We have CRM integration using HCI working for most of the standard objects running. But for "Service Request" we are not able to see replication initiating from C4C to CRM. We have setup the required Communication Arrangement and artifact on HCI. Ping test gives 405 error which is as expected. But when we save the new ticket replication to CRM is not initiated.
Kindly throw some light on this so as to understand why this replication is not initiated.
Please let me know if any configuration missing to replicate "Service Request" from C4C to CRM.
Thanks & Regards,
Mithun

Hi Ravi,
We are not getting any messages under "Business Communication Monitoring" and web service messages monitoring.
Can you please suggest me which are the all configuration/activities require in cloud for customer for "Service Request".
We have maintained the Transaction Type for "Service Request" in Code List Mapping too, however we are clueless where we have to maintain the "Item Category" for "Service Request" and map to which standard "Item Category" in cloud.
What is the initiate point to trigger the "Service Request" from C4C to CRM?
Many Thanks,
Mithun

I have an AirPrint printer and am signed up for the wifi 3G service but will not have wifi. Can an IPad be hooked to a printer with a cable, or can I print somehow without wifi?

I have a new air print-capable printer and am signed up to Verizon wifi+3G service but will not have wifi while traveling. Is there anyway to print from my iPad in this situation? Cannot the IPad be hooked up to a printer with a cable? If not, this seems to me to be a real shortcoming with an iPad!

iPads cannot be connected to a printer using a cable.
You need some form of Wi-Fi network to print. You do not need to have that Wi-Fi network connected to the internet. There are some devices that will create a Wi-Fi network and allow you to print. Google it to find someplace ossicle solutions.

User role for service requests from the SSP

Does the End User role have enough permissions for users to create service requests from the SSP? I know for incidents it is but I am not sure about service requests. If you go through the Service Catalog Checklist, step 5 to create the User
Role brings up a new role based on the Author role and not on the end user.

here step by step procedure with user access.
http://www.concurrency.com/blog/scsmportalpermisions/
Cheers
Antoine AL Ibry

Extending the class - For extra feilds\properties on service requests

We have extended the class for service request so we can have extra properties for user input on service requests. These extra feilds are now visible via the extensions tab at the top of the service request and also on a new tab next to Histroy.
However each time we open a new service request the default tab it opens onto is this new "Notes" tab and not the "General" tab, causing a lot of fustrations. See below:
Anyone know how to change this default view back to the general tab?

An annoying "feature" of SCSM form customisation is that the last tab changed becomes the default tab shown. Open your custom form MP in the Authoring Tool again and go to the general tab, change the top margin by 1 of the title or something
similar, reseal, import. The general tab will be the default once more.
Rob Ford scsmnz.net
Cireson www.cireson.com
For a free SCSM 2012 Notify Analyst app click
here

OT:Looking for a service that will take donations for a non-profit

I am looking for a type of service that will take credit card information and allow donation to a non-profit (library in this case). I am not sure anyone here might now of this service, but the local director of the library has asked about this service.
Thanks,
Jim

Assuming the non-profit already has received 501(c)(3) tax status, start with their merchant bank account. Authorize.net, PayPal and other payment gateways can all process credit cards for non-profits. The benefit of having your own merchant account is that your nonprofit will be the party named on the donor's credit card statements, and funds will flow directly to your nonprofit's bank account.
If you want 3rd party service that specializes in non-profit solutions, look at Blackbaud.com
Nancy O.

Dynamic bandwidth selection for PPPoE over Ethernet/VLAN

Hello all, hope you are doing great.
I'm planning to deploy PPPoE Server (Cisco Router 7609) for a ISP. This ISP will provide Internet connection for customer over Ethernet.
I have to provide a solution to assign bandwidth to each customer by RADIUS and I find some clues that Dynamic Bandwidth Selection (DBS) should be the answer. Unfortunately, DBS only support PPPoA or PPPoE over ATM.
If you have any experience with equivalent function, please help me. Thank you very much.
Regards,
Hiep Nguyen.

Hiep,
I think I have figured this out. Here is the test config on my PPPoE server:
int lo1
ip address 172.25.25.25 255.255.255.255
ip radius source-interface Loopback1
aaa new-model
radius-server host 172.16.1.55 auth-port 1812 acct-port 1813 key cisco$$$
aaa group server radius RADIUS-ACT
server 172.16.1.55 auth-port 1812 acct-port 1813
aaa authentication login default group RADIUS-ACT local
aaa authorization exec default group RADIUS-ACT local
aaa accounting exec default start-stop group RADIUS-ACT
aaa accounting delay-start
aaa authentication ppp default if-needed group RADIUS-ACT local
aaa authorization network default group RADIUS-ACT local
aaa accounting network default start-stop group RADIUS-ACT
aaa accounting update periodic 5
bba-group pppoe global
virtual-template 1
interface fa0/1
pppoe enable group global
ip address 172.30.0.1 255.255.0.0
no shut
interface Virtual-Template1
mtu 1492
ip unnumbered FastEthernet0/1
peer default ip address pool GLOBALPOOL
ppp authentication chap
ip local pool GLOBALPOOL 172.30.0.2 172.30.127.255
policy-map POLICE-128K
class class-default
    police 128000
policy-map POLICE-512K
class class-default
    police 512000
Here are the attributes on the radius server, for a group the PPPoE customer belonged to:
Service-Type = Framed
Framed-Protocol = PPP
cisco-avpair="ip:sub-policy-In=POLICE-128K"
cisco-avpair+="ip:sub-policy-Out=POLICE-512K"
Here is the show policy-map on the virtual-access interface the client connected on:
sho policy-map int virtual-a 3
Virtual-Access3
Service-policy input: POLICE-128K
    Class-map: class-default (match-any)
      1000 packets, 1402000 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match: any
      police:
          cir 128000 bps, bc 4000 bytes
        conformed 799 packets, 1120198 bytes; actions:
          transmit
        exceeded 201 packets, 281802 bytes; actions:
          drop
        conformed 0 bps, exceed 0 bps
Service-policy output: POLICE-512K
    Class-map: class-default (match-any)
      911 packets, 1137746 bytes
      5 minute offered rate 0 bps, drop rate 0 bps
      Match: any
      police:
          cir 512000 bps, bc 16000 bytes
        conformed 799 packets, 1136178 bytes; actions:
          transmit
        exceeded 0 packets, 0 bytes; actions:
          drop
        conformed 0 bps, exceed 0 bps
I was able to generate enough traffic with ping to meet the exceed action in and have it drop packets.

SELECT FOR UPDATE with the SKIP LOCK clause

Hi,
I have a query regarding the SELECT FOR UPDATE with the SKIP LOCK clause.
Whether this will be really good for parallel processing.
Also if we are selecting a set of records in a cursor whether the lock will be done at the records level once we fetch the records?
Also do we have any known issues with this one?
We are trying to figure out whether this will fit for business requirement, we are trying to do a implement a threading kind of thing for our stored procedure invocation in background using shell script.
Any suggestion or feedback on this will be helpful for us.
Thanks a lot for the support given....
Regards,
Basil Abraham.

http://www.oracle.com/technology/oramag/oracle/08-mar/o28plsql.html
Please read the above thread for few information...Thanks!

F-44 ZBAPI MULTIPLE LINE SELECTIONS FOR WEB SERVICES

HI TO ALL,
I HAVE WRITTEN ZBAPI FOR POSTING MULTIPLE LINE SELECTIONS FOR TCODE F-44, THE ZBAPI CONSIST OF BDC PROGRAM, WHICH IS WORKING IN SAP SYSTEM PERFECTLY BUT WHEN I AM USING IT IN WEB SERVICES IT IS THROWING A ERROR MESSAGE.
PLEASE CAN ANY ONE TELL ME DOES THIS PROCESS WILL WORK OR NOT, IF YES HOW IS IT POSSIBLE

Hi Gabriel,
Let me try to answer some of your questions:
1) The "Requires Secure Access" attribute of a resource handler controls whether this handler must be accessed/consumed only over SSL (HTTPS). Oracle Database Cloud Schema Service is only offered over SSL, so this attribute does not have any effect on RESTful services deployed in this environment (because secure access is always required and there is no other way). That said, if you want to access such web service from your own APEX instance, your instance must have Oracle Wallet configured with appropriate SSL certificate.
2) The URI parameters are not required. If your web service returns data for many entities (for example, list of employees in employees/), you may not need a parameter. If your web service returns data for one specific entity (for example, details of one employee in employees/{id}), you may want to identify that entity with a URI parameter.
3) You can have many URI parameters, for example: customers/{id}/orders/{order_id}.
4) Yes, these are the same HTTP methods/verbs you would use from PHP.
5) If you are trying this POST example from your own APEX instance (not Oracle Database Cloud Schema Service) and you are trying to access a web service over SSL, then it is likely that the Oracle Wallet used by your instance does not include the required SSL certificate(s), or the Oracle Wallet is not configured at all.
6) I recommend to check RESTful Web Services for the Oracle Database Cloud white paper and Oracle REST Data Services Developers Guide. Oracle REST Data Services is the technology that enables RESTful services in the Oracle Database Cloud Schema Service.
You can certainly create your own web services in the Oracle Database Cloud Schema Service and consume them from the same environment.
Vlad

Data types used in a sub VI - selecting the correct input and output types?

data types used in a sub VI - selecting the correct input and output types?
I can never work out how to choose an input or output format for Subvi's.
I want to create a SubVI for the code in red. I needs an VI Server Reference compatible input and an output that goes to a waveform.
Thanks in advance.
Attachments:
data types.PNG ‏11 KB

GerdW,
I realise now I have taken us in the wrong direction. apologies for that.
History, this is not my code and I do not own the process and NOT my preferred method of using it. I was looking for a simple way to make subtle changes.
What we do - We use these programs to collect data from typically 6 pressures and 6 temperature probes and capture RS232 / USB VISA strings from sensors.
So every few weeks / months or up to a year we rearrange each sensor location to suit the new process. I did not write the code. I cannot change the procedure too much without resistance.
So headers in the CSV file have the DaqMX string passed through the code. Great.
Other data to the CSV file comes from calculations or extracted from the VISA string. Hence why we have headers with "Untitled 1 ()". These values also go to a History Chart.
So I was looking for a simple way to read the the local variable label as it is always linked to the front page indicator. People can cope with editing the indicator label, save the VI and hit run.
TL;DR - GerdW is now a psychologist.
Attachments:
data to csv and history chart.png ‏1043 KB

Field selection for order

Hi all
Can I know use of custumization trxn OIXW and OIRS (Field selection for order and sub order data field.)
My assumption was that when I make sequence chane in OIXW then tht will reflect in IW38/IW39.
but it is not so.
Basically I want to araange column sequence in Iw38 as per my requirement. instead of creating layout is there
any other procedure ?
Regards,
Prasad

Hi,
Any changes you make in field selection through OIXW or OIRS will reflect in IW38/IW39 as a global default variant.Any user variant created as default variant will have priority over this.So make it sure that this default variant is Protected one so that no one can chnage as you want this to be global variant.
regds,
atul

Define Field Selection for Move-In Contract Data

In Move-In customization, in IMG activity u201CDefine Field Selection for Move-In Contract Datau201D when you go for u201CField Selection u2013 Modifiable Fieldsu201D Screen (Transaction is EQ07), I am seeing four buttons as follows.
u2022     Modified
u2022     Influencing
u2022     Screen Groups
u2022     Influences
I would like to know the applications of that buttons.
Also, if I click the u201CModifiedu201D button, it takes me to another screen in which I am seeing seven buttons as follows.
u2022     New Values
u2022     Delete Value
u2022     Influencing
u2022     Modifiable
u2022     Screen Groups
u2022     Influences
u2022     View
It would be really great if someone explain me about this.
Thanks,
Meenakshi Sharma

hi meenakshi
here are some data 4 u
modified---if u click that u will come to know whther any field is modifies or not previosuly
influence--after u make a modification the effect or the change is shown in influences
screen gpr os nothing but all the main and sub screens involved for a particular transaction
influencing field is something like u   have some connection witht that field,for example click screen grp and screen modification in contract and then click infuencing u can see the 2 fields whch are set as influeincg fields for contract
u can change the selection fro i/p to diaply and save it and see the changes or details showed by clicking each button..hope u willl finds a lot urself
kr
raj

FYI: "Sub-technology" selections for UCCE/UCCX TAC Service Requests will be updated soon

Similar Messages

Maybe you are looking for