G4 sawtooth and wireless network

My G4 is connected to my LAN using a ethernet cable. This just works fine, but I would like to connect to my LAN using a USB-adapter.
So I bought one from Netgear (WG111) because they offer a Macintosh driver.
Anyhow I was not able to build up a connetion to my router.
So there are two questions:
1st. Is anybody using the WG111 and can tell me what to do ?
2nd. Can anybody say something about other USB adapters which will work with my G4 ?
Looking forward to hear from you experts !

Hi Helmut, I haven't used that one, but plenty of other similar ones... ASUS WL167G, & far too many others to mention, but here are some...
http://eshop.macsales.com/Search/Search.cfm?Ntt=usb wifi
Is anybody using the WG111 and can tell me what to do ?
Since it has Mac Drivers, perhaps we can get it working.
First you install the Software without it plugged in, Repair Permissions & reboot.
Plug in the WG111, go to System Preferences>Network>Show:>Network Port Configurations, you should get a popup stating New Port found, that Interface dragged to the top of Network>Show:>Network Port Configurations and checked ON.
Then put these numbers in Network>TCP/IP>DNS Servers, for that Interface you connect with...
208.67.222.222
208.67.220.220

Similar Messages

G62-454ca won't turn on.power led and wireless network led keeps blinking every 3-4 seconds

Please help.when I try to turn on nothing happens.Only power LED and wireless network led keeps blinking every 4 seconds

According to the message you have recently posted I would like to confirm that this is a hardware issue and I strongly recommend you to immediately Contact HP Technical Support over the Phone for further assistance without any delay to get your Notebook diagnosed and serviced by an authorized HP Certified Engineer
You can also Check your warranty Here to verify the warranty status
Hope this helps, for any further queries reply to the post and feel free to join us again
**Click the KUDOS star on left to say Thanks**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Thank You,
K N R K
Although I am an HP employee, I am speaking for myself and not for HP

DHCP Server - Different Range for Wired and Wireless Network

We have DHCP setup on Windows Server 2012r2 and the range given to us by the main HQ is 10.65.112.1-10.65.112.254 (there are several exclusions under this range)
Now since the range gets exhausted quickly, they provided another one 10.65.122.1-10.65.122.254.
What our branch would love to do is to dedicate the first range for Wired Computers and the other range for Wireless Devices (Phone,Tablets, Mobiles)
Right now we have 2 different scopes setup in DHCP, the second one is disabled. In our network we have 6 access points and also have a CISCO SG300-52 Managed Switch. It has an inbuilt DHCP Server and also has the function for DHCP Relay. But we are not actually using any of its functionality as of now.
So my question is how to have 2 separate ranges for wired and wireless network. People have mentioned vlans but I have no clue on how to get that done.
Is there a simpler way avoding V-LANS or if not, would love to get step by step procedure on how to go about this. Any help will be much appreciated
Regards,
Sheldon

Hi Sheldon, please read this post
https://supportforums.cisco.com/thread/2270049
You will need some modifications though. Steps 1-6 is very relevant. On step 6, you need to pay particular close attention to the "default router". If the SX300 handles your intervlan routing then the default router needs to be the IP of your VLAN. If you have a different device to handle VLAN routing then the default router needs to be that IP address.
-Tom
Please mark answered for helpful posts
http://blogs.cisco.com/smallbusiness/

Officejet Pro L7780 Wired and wireless networking at same time

I have an officejet pro L7780 printer that I would like to use wired and wireless networking at the same time. It that possible. The printer is connected directly to the network by ethernet, but I would like to print wirelessly with an ipad or iphone using HP ePrint Home and Biz.
Thanks,
Maurice Hawley

The bad news: no it is not possible to have two connections active on your printer at once.
The good news: the router will connect any device to the printer regardless of how the printer or the devices are connected. So your iPad can print to a printer that is wired (with Ethernet) to your router.
If it does not work, restart your router by pulling its power plug momentarily.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Airport and Wireless network issues

I have read all the issues about airport and wireless network. I don't see the issues that I have. My issue is that my wireless network used to automatically connect as soon as I power up my powerbook; then one day I power up and I was connected to default and I did not see my wireless address listed. I when into airport setup to try and setup again and it would not let me saying my password was not right. I logged off and then on again this time my network address was listed, but it still would not connect automatically to the network, now everytime I go to the web I must pick my own network and put in a passwork that sometimes works and sometimes not.
I have not done any updates or put any new software on the powerbook, so this is not the reason for my problem.
Please Help!!!
Thank's
La Vern
G4 Power PC 15in Alum Mac OS X (10.3.9)

Had this issue with our imac after upgrading to 10.4
The answer was to go into Network and select airport tab.
Listed there (for me) were three settings. Delete all of them ,they will probably include the actual network you want! Click to apply. Re-start the Mac.
Go back to network and airport and you should now see only the network you wish to join. It will ask for passwords again!!
Click apply and restart. It worked for me.

Problem with Skype and Wireless Networks

I have been having a problem with Airport for about 10 months. Long winded explanation follows.
Initially file transfers over wireless networks were extremely slow but this seems to have been that 10.5.2 update problem. There is a remaining issue when I use Skype on my Mac (details below) connected to a wireless network the incoming and outgoing audio drop out for 1 - 3 seconds at irregular but frequent intervals (approx every 5 - 10 seconds). This is regardless of the wireless network I am on - and that is dozens of them all over the world. Note it is voice only calls, not video. Apple has replaced the Airport card and the mother board; the OS has been reinstalled; test accounts set up but nothing fixes the problem.
At one point I had temporary relief by switching off 'Configure IPv6' in System Preferences/Network/Airport/TCP/IP. This worked for a month or so but now the problem is back as before.
All other aspects of wireless activity are fine. Wireless firmware is 1.4.4.
I have worn out my welcome with the usually sensational help desk. Any suggestions out there in Mac Land?

Hi there
Been a hectic week here getting this problem resolved. It is all OK now. Here is what we found and how it was done.
When Airport was playing up we set up an unlimited ping of the wireless router in the office. This is what it showed:
PING 10.10.10.1 (10.10.10.1): 56 data bytes
64 bytes from 10.10.10.1: icmp_seq=0 ttl=255 time=1929.885 ms
64 bytes from 10.10.10.1: icmp_seq=1 ttl=255 time=929.788 ms
64 bytes from 10.10.10.1: icmp_seq=2 ttl=255 time=2.633 ms
64 bytes from 10.10.10.1: icmp_seq=3 ttl=255 time=1.845 ms
64 bytes from 10.10.10.1: icmp_seq=4 ttl=255 time=1.941 ms
64 bytes from 10.10.10.1: icmp_seq=5 ttl=255 time=1922.656 ms
64 bytes from 10.10.10.1: icmp_seq=6 ttl=255 time=922.724 ms
64 bytes from 10.10.10.1: icmp_seq=7 ttl=255 time=2.012 ms
64 bytes from 10.10.10.1: icmp_seq=8 ttl=255 time=1.974 ms
64 bytes from 10.10.10.1: icmp_seq=9 ttl=255 time=2.283 ms
64 bytes from 10.10.10.1: icmp_seq=10 ttl=255 time=1918.448 ms
64 bytes from 10.10.10.1: icmp_seq=11 ttl=255 time=919.372 ms
64 bytes from 10.10.10.1: icmp_seq=12 ttl=255 time=2.609 ms
64 bytes from 10.10.10.1: icmp_seq=13 ttl=255 time=2.037 ms
64 bytes from 10.10.10.1: icmp_seq=14 ttl=255 time=2.259 ms
64 bytes from 10.10.10.1: icmp_seq=15 ttl=255 time=1921.022 ms
64 bytes from 10.10.10.1: icmp_seq=16 ttl=255 time=920.825 ms
64 bytes from 10.10.10.1: icmp_seq=17 ttl=255 time=2.416 ms
64 bytes from 10.10.10.1: icmp_seq=18 ttl=255 time=2.063 ms
64 bytes from 10.10.10.1: icmp_seq=19 ttl=255 time=1.954 ms
64 bytes from 10.10.10.1: icmp_seq=20 ttl=255 time=1917.649 ms
64 bytes from 10.10.10.1: icmp_seq=21 ttl=255 time=917.617 ms
64 bytes from 10.10.10.1: icmp_seq=22 ttl=255 time=2.018 ms
64 bytes from 10.10.10.1: icmp_seq=23 ttl=255 time=2.057 ms
64 bytes from 10.10.10.1: icmp_seq=24 ttl=255 time=2.106 ms
64 bytes from 10.10.10.1: icmp_seq=25 ttl=255 time=1916.329 ms
64 bytes from 10.10.10.1: icmp_seq=26 ttl=255 time=916.347 ms
64 bytes from 10.10.10.1: icmp_seq=27 ttl=255 time=2.020 ms
64 bytes from 10.10.10.1: icmp_seq=28 ttl=255 time=2.151 ms
64 bytes from 10.10.10.1: icmp_seq=29 ttl=255 time=2.005 ms
64 bytes from 10.10.10.1: icmp_seq=30 ttl=255 time=1915.818 ms
64 bytes from 10.10.10.1: icmp_seq=31 ttl=255 time=915.821 ms
64 bytes from 10.10.10.1: icmp_seq=32 ttl=255 time=2.091 ms
64 bytes from 10.10.10.1: icmp_seq=33 ttl=255 time=2.061 ms
64 bytes from 10.10.10.1: icmp_seq=34 ttl=255 time=2.064 ms
64 bytes from 10.10.10.1: icmp_seq=35 ttl=255 time=1911.739 ms
64 bytes from 10.10.10.1: icmp_seq=36 ttl=255 time=911.753 ms
64 bytes from 10.10.10.1: icmp_seq=37 ttl=255 time=1.923 ms
64 bytes from 10.10.10.1: icmp_seq=38 ttl=255 time=2.788 ms
64 bytes from 10.10.10.1: icmp_seq=39 ttl=255 time=1.911 ms
64 bytes from 10.10.10.1: icmp_seq=40 ttl=255 time=1907.626 ms
64 bytes from 10.10.10.1: icmp_seq=41 ttl=255 time=907.528 ms
64 bytes from 10.10.10.1: icmp_seq=42 ttl=255 time=1.847 ms
64 bytes from 10.10.10.1: icmp_seq
and so on.
After discussion with tech support they said the Airpot card had to be replaced. This was done with admirable expediency and I got the MBP back in 36 hours. On testing it the same problem was still there. Identical pattern on the ping test, the fault was not the hardware.
Once more a call to Apple and another tech. This time we booted from the OS 10.5 install disk and ran the ping test. I ran it for a few hours without seeing the fault, it worked fine. The problem had to be in the operating system.
After backing up all the data I zeroed the drive and did a clean install of the OS. Bingo! Problem gone.
So after 10 months, two airport cards and a mother board, the issue was in fact something corrupt deep in the OS.
So to anyone having similar problems with Airport, run a ping test as described above. If you see that kind of pattern, try a clean install before going down the hardware road.

How to set up an integrated wired and wireless network

I have an iMac 17" 1GHz connected to a ethernet hub which in turn is connected to a DSL modem and from there to my ISP. I also have a MacBook Pro wirelessly connected to an AirPort Express; the AE is connected to the same ethernet hub through its ethernet port.
I can connect to the Internet wirelesly using the MacBook Pro, but I can not seem to connect to the iMac.
How can I keep the iMac wired and the MacBook Pro wireless, but see both on a network? The AE instructions don't seem to have an example for this kind of network.
Any help would be greatly appreciated!
Cheers,
Martin
MacBook Pro Mac OS X (10.4.6)
MacBook Pro Mac OS X (10.4.6)

Martin,
As Frank said, you'll need a router with DHCP and NAT abilities (nearly all have this) connected to the modem.
But just in case your "ethernet hub" is actually a router, just re-configure the AE not to distribute IP addresses - AirPort Admin Utility - Network tab. Try that and let us know.
For minimal clutter, if you were DSL broadband instead of cable, you could sell the modem, sell the ethernet router, sell the Airport Express and buy a single Ethernet and Wireless DSL modem router - for less than the price of the AE. Some people like to keep the modem separate to make upgrades to the modem cheaper. My solution is to buy a decent modem in the first place, ie make sure it has ADSL2+. Almost all modem/routers do this now, even my ancient ones have firmware upgrades to offer this.
For minimal spend, you can pick up an Ethernet router for about $30. Just replace your ethernet hub with it.

Wired and wireless network setup

I have a small home network, wired right now. I would like to add a wireless access point for near future laptops. Can I add a second router that is wireless to my wired network with having to load router software on a second computer. Is this even possible. My network consists of my PC, HP M8300f desktop PC as home base/client and cable modem with linksys wired router, BEFSR41 connected to a dell 2400 desktop. I am wanting to add a linksys wireless router WRT54G some where in the living room for and access point. Do I have to load the software on the Dell PC or can I just plug in router to wall socket and connect wirelessly that way. Thanks for the help. Just thinking out side the box.
OS Vista Home Premium 32 bit
CPU AMD Athlon 64x2 6000+ 3.0ghz
Motherboard Asus M4N78 Pro
Memory 3Gb PC2-5300 DDR2 @ 667mhz
Graphics Card BFG Nvidia Geforce 8400 GS 512MB DDR2
Monitor(s) Displays HP W1907 LCD 19", Gateway HD 19" LCD
Antec Earthwatt 80 plus 500 watts
Hard Drives 640GB 7200rpm SATA (2x320)
Other Info Optical: Super Muliti DVD burner w/lightscribe, Hauppauge WinTV HVR-1800

You can add your WRT54g to your wired network without too much trouble if you follow a couple of simple steps:
Turn off the DHCP server in the wireless-router.
Create an unique wireless network name (aka SSID) and turn on WPA-PSK security.
Make sure the web-page IP address for the wireless-router is set to a unique value different from any of the other wireless devices on your network.
Connect the LAN port of the wireless-router to the LAN port of the Ethernet router. Do not connect to the wireless-router's WAN port.
This configures your wireless-router into a simple Access-Point and is the easiest way to extend your home network with wireless.
Best Regards / Jim B
Regards / Jim B / Wireless Enthusiasts
( While I'm an embedded wireless systems engineer at work, on this forum I do not represent my former employer, Hewlett-Packard, or my current employer, Microsoft )
+ Click the White Kudos star on the left as a way to say "thank you" for helpful posts.

Using a wired AND wireless network on one machine for better security

It occurs to me that if I could separate my Internet traffic from my LAN traffic, I could have the best security setup, so that machines on my network would only have file sharing enabled for the WIRED connection and I would use the Internet over the WIRELESS connection.
How do I configure my PowerBook and Mac Mini to do this? In the Sharing preference pane, it doesn't allow me to specify which network port the sharing will be active on.
And once I am conncected to both a wireless and wired network, giving each machine 2 IP addresses, how does the computer know to route the IP addresses to the right port?
I'm using an Airport Extreme Base Station (connected to a cable modem) configured to distribute IP addresses to the wireless ports on the computers for Internet and a Linksys router distributing IP addresses to the ethernet ports on the computers with sharing turned on.

in the Thinkvantage Access software, you can set the network preferences. So you can set the Ethernet to be your most preferred network connection method, while your wireless as the second most preferred method. Or which way you prefer.
So for example, when you dock and the computer detects the ethernet network connection, it will automatically switch to the ethernet as it becomes available. And when you undock, your computer will switch back to wireless as ethernet is not available.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

A very strange wired and wireless network issue

Hello,
I have never had any issue at all with my macbook (2008) until this week, I use it both for work and personal use.
Most of time, I'm used to be on customer site, so I use wired and wireless connections depending of the situation....
I have never had any issue at all with wifi neither ethernet connections during three years, until this week... and I can say this is the most strange thing I have ever seen....
Using wired or wireless connection, always the speed of network was really good, at home, many customers, etc never had any problem...
But this week I'm currently out of home, and the hotel where I'm staying I'm having very poor network rate....
Using wireless connection, the download speed is no more than 10kb.... and using ethernet I get less speed... but during the day I'm on customer site, using the ethernet connection and download speed is really good, more than 500k-800k....
I have already tried in the hotel few wifi connections (there are three) and differents wired connections (in diferent rooms) and the download speed is always the same, no more than 10kb...
During this afternoon, I could go into hotel's lab and could connect directly to the router using cable, same speed no more than 10kb....
The most strange thing is on their computers the download speed using wired connection is around 6Mb....
how is possible I'm getting no more than 10kb of download speed when the pc's at hotel using same wired connection gets 6Mb?
I have already deleted current network connections, execute onyx to clear everything, perform dhcp connection, tried manual ip etc, and always the results are the same...
I know there is no problem with the macbook, because it works pretty good at every location I've been... but until this week...
Sincerely I'm getting a little crazy here, I'll appreciate any help!!!
thanks in advance

I've seen something like this on my T400 when it was running Vista. Now that I use Win 7 it's been OK. I rather doubt that your issue is the same but I'm tossing it out here just on the off chance.
Im my case, I had to downgrade my Intel 5300 card to a 5100 (as suggested by a Lenovo 2nd-tier tech) to get things working.
My symptoms were a little different. Wifi was fine until I went back to a wired network. After that, trying to use the same wifi AP as before would end up associated, but no internet access. DHCP wasn't working. The GUI "find" app didn't work as expected either. Some APs showed up, and some didn't.
If I configured for automatic connection to my home AP it would try and fail. Just rebooting at that point would again attempt an automatic connection that would succeed.
What I have noticed now that I run Win 7 is that Access Connections is completely useless. Often the "finder" doesn't show an AP 3 feet away. I didn't notice that this happened after a switch from wired, but maybe.
Are you using Access Connections? If so, you might try uninstalling it.
Sorry I can't be of real help,
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Serious issue with Mac OS X 10.6.4 and wireless networking

Hello there, I'm having a serious issue with my TP-Link WP-8910G wireless router and Mac OS X 10.6.4 .
Problems began some days ago. In short, after a certain period of time, my router drops the wireless connection out and, when I try to re-establish it, if a very short period of time has passed after disconnection Airport detects the wireless network and returns "connection timeout". If I wait more, no wireless connection is detected, and I have to reset the router and re-connect Airport. This is very annoying.
How can I solve this issue?

Have you verified that the router is not the problem?

MacBook, 10.4.8, and wireless network problems. How I solved it.

Hi
I've seen a few post about not connecting to a wireless network after the 10.4.8 upgrade.
Before the 10.4.8 update my MacBook worked fine on my wireless network; after the 10.4.8 update I could not connect to my network via AirPort, though it kept offering to connect to my neighbours networks. My wireless network is configured for WPA.
I managed to get this working by deleting my existing AirPort network configuration from System Preferences and creating a new configuration with the same network settings.
Hope this helps,
Matt
iMac G5 1.8GHz 1GB 20"; MacBook 1GB; Mac OS X (10.4.8)

In "Network" I deleted all prefered networks one by one, set it to automatic, turned airport off and back on, and add my network again as prefered network, set it back to connect to preferred network. see apples instructions:
http://docs.info.apple.com/article.html?artnum=304482
Now its fast and connects by it self again.

Dreamweaver and wireless network problem

This isn't about Airport, but I couldn't find the proper place to post this, so I put it here. Please advise if I'm wrong.
I'm running Tiger (10.4.2) on a dual G5. My husband is running Windows XP on a 2GHz Dell, and also a Dell laptop. We just moved and HE is wireless now, not me. I am hardwired to a Netgear router (doesn't seem to have a name but the number on the bottom is CD814WG). We are using RoadRunner as our ISP, as we have done for seven or eight years, since its introduction into our city. TimeWarner did our installation, and everything is fine with my machine (although my husband's problems are another issue altogether!).
I should also say that we are in no way networked, and that is not our goal or plan. We have the Netgear router, and as I mentioned, I'm wired directly to it. We both use broadband individually, and have no need to share a connection.
I'm not having any problems at all with my broadband connection -- internet and Mail are fine -- but since the installation of the Netgear router I can't use Dreamweaver to upload HTML pages I create. I can use Fetch just fine, which doesn't surprise me since I've always powered right through my firewall with Fetch, while I always had to turn it off, with Dreamweaver. And of course I should say that my firewall is down when I have the uploading problem. The built-in OS X firewall is currently the only one I have installed, BTW.
When I try to upload, DW gives me a dialog box saying "Dreamweaver cannot determine the remote server time. The Select Newer and Sychronize commands will not be available." And of course I can't upload anything.
Any ideas? I have the information the TimeWarner guy left here so I can go onto the Netgear admin page, but I don't know what to change/add so that I'm able to upload with DW. It's my understanding that port 80 is for internet connections, but as I mentioned, it's not blocked -- I can go online just fine. It's just that I can no longer upload HTML pages with Dreamweaver.
Thanks in advance...

I'm getting the same error message as you (Dreamweaver cannot determine the remote server time...).
I found that I could no longer upload with Dreamweaver (or see all the remote files) but I could with Transmit. However (and here the similarity ends) when I turned off the OSX firewall everything was fine.
This didn't make me feel very easy, however, as I preferred having the firewall up. I found that it would work with the firewall up if I checked the "use passive FTP" box in Remote Info in the Site Definition menu.
The Netgear router also has an NAT Firewall but I am using a Netgear router too, both hardwired on my iMac (via Airport Extreme - don't ask!) and wirelessly on my laptop. I haven't configured the firewall on that at all (I wouldn't dare!) and I'm getting through OK now. Try the passive FTP thing; it might work!

Bluetooth and wireless network not working

About a week ago my iphone 4s stopped discovering my bluetooth devices. Today, it will not let me log onto my wireless network as well. I have reset both my phone and router, but nothing seems to be working. Any suggestions?

While trying to log onto my wireless network I get an error message stating that I have used an incorrect password, but the password is correct and works with my other devices.

Problems with Installing iTunes and wireless network connection

Every time I attempt to install iTunes it completely kicks the internet off and an error comes up that the wireless network adapter to not connect or is not detected. My internet service is connected to a router which I receive wirelessly to my laptop. I do not understand why it is happening and to get the internet to work again I needed to do a system restore. Any ideas why this is happening. Also when iTunes was installed it came up correctly, it would just not connect to the net. I have had a previous version on my old laptop but since purchasing this new laptop I am having such difficulty. On another note, if this problem can be resolved, once iTunes is working is there a way to get the songs from my old computer onto the new? Thanks for the help in advance!

I just saw your post and I resolved this on mine for my wired connection. I'm willing to bet that the issue is the same for wireless. Here's what I found.
Issue:
During the installation, iTunes installs some network components related to mobile device support over ethernet(Apple Mobile Device Ethernet Service - netaapl.inf). At the same time, according the logs, the install process removed OEM18.inf. This almost exactly coincided with the time that I saw the network connection die (preceded it by a few seconds).
Basically, iTunes appears to be removing a required network component.
Resolution:
After installing iTunes and the network connection breaking, remove the network device from Device Manager and allow Windows to reinstall it automatically.
The following instructions are for Windows 7, but they are close enough to follow for other versions of Windows.
1. Click the Start button (Jewel in Vista and Win7).
2. Right-click Computer and click Manage in the menu that appears (type your password or click Yes if prompted).
3. On the left side of hte Computer Management window, click Device Manager.
4. Click the arrow (or plus sign) next to Network Adapters to expand that section.
5. Right-click your network adapter and click Uninstall in the menu that appears.
6. Click OK.
7. Reboot.
Windows should automatically detect and reinstall your network device on boot.

G4 sawtooth and wireless network

Similar Messages

Maybe you are looking for