G5- installed ram; turned on and no chime, gets power and fan, no video

Also will not boot from CD. I replaced the lithium battery, reset everything I have read about here. I don't think system gets up enough to recognize the keyboard. Have had issues over years with fan getting loud periodically and a few hard to wake instances, but system would always restart. I don't know if the system crashed due to ram or if it was "just time". I removed the new ram and still have same result. Any other options I can try on my own?

Where'd you get the RAM, G5s are mighty particular about RAM.
Can you count the blinks?
1 beep = no RAM installed
2 beeps = incompatible RAM types
3 beeps = no good banks
4 beeps = no good boot images in the boot ROM (and/or bad sys config block)
5 beeps = processor is not usable
In addition to the beeps, on some computers the power LED will flash a corresponding number of times plus one. The LED will repeat the sequence after approximately a 5-second pause. The tones are only played once.
Is it...
True PC3200, Non Stacked 64x8 16 Device
Product Specifications
* Size: 1024MB (1GB)
* 184-pin DIMM
* 64x8 device based 128x64 Module
* 8 Non-Stacked TRUE PC3200 Devices per side
* Data Rate = 400MHz
* CAS: 3.0
* Low Noise 8-Layer PCB
* Exceeds Apple/Intel Specifications
* Also supports PC200 CAS 2.0, PC2100 CAS 2.0 or 2.5 operation, PC2700 CAS 2.5 operation.
* Fully complaint with JEDEC specifications
http://eshop.macsales.com/item/Other%20World%20Computing/3200DDR2GBP/

Similar Messages

  • HT201210 i updated my iphone 3gs to iphone 6 . while installing the software it gets error and closed. then i restored my previous version. when i turned on the phone it gets usb and itunes symbol on screen. when i run itunes error is coming like server c

    i updated my iphone 3gs to iphone 6 . while installing the software it gets error and closed. then i restored my previous version. when i turned on the phone it gets usb and itunes symbol on screen. when i run itunes error is coming like server contact problem. what can i do to start my phone????  plz help me

    I will need a little bit of information about your phone. What kind of error are you getting?

  • My ipod touch 4th gen will not turn on, i have held the power and home buttons, i have plugged my ipod into itunes and tried again, yet nothing happens, what should i do?

    My ipod touch 4th gen will not turn on, i have held the power and home buttons, i have plugged my ipod into itunes and tried again, yet nothing happens, what should i do?

    Try:                           
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • I just purchased an airport extreme router to increase the range of    my wifi. I have an imac with 10.5.8. I get a flashing yellow light on the base unit and it tells me I need airport utility to install yhe ubnit. Where do I get this and how do I do it?

    I just purchased an airport extreme router to increase the range of my wifi. I have an imac with 10.5.8. I get a flashing yellow light on the base unit and it tells me I need airport utility to install yhe ubnit. Where do I get this and how do I do it?

    sylviafromhanover wrote:
    So I assume that the original modem stays installed with the coaxial cable and the Exrtreme is in addition to that. 
    Yes, that is correct.
    Did you have the instructions that came with your Airport Extreme?  Are you sure you have it setup properly?  Here is the setup guide:
    http://manuals.info.apple.com/en/airportextreme_802.11n_userguide.pdf 
    Ensure you have everything setup properly.  Once you do this and if you are still having trouble, follow Star's instructions. 

  • I installed new OS to my IPhone 4 and now phone gets hangs and not able to type or chat .. how to resolve it now

    i installed new OS to my IPhone 4 and now phone gets hangs and not able to type or chat .. how to resolve it now

    Try a reset to begin with. hold down the Sleep and Home key until Apple logo appears on the screen.
    Regards,
    Steve

  • I just bought a new iMac and used the Migration Assistant to transfer my files. Initially, all was working, but now a week later, I get the message that the application manager is missing, and I cannot get Photoshop and InDesign to launch. I do not want t

    I just bought a new iMac and used the Migration Assistant to transfer my files. Initially, all was working, but now a week later, I get the message that the application manager is missing, and I cannot get Photoshop and InDesign to launch. For my personal use, I did not a need to join Creative Cloud. Have you any suggestions for a work-around?

    Try to install Adobe application Manager from below link and check
    Adobe - Adobe Application Manager : For Macintosh : Adobe Application Manager : Thank You

  • Optical drive on iMac at work, barely one year old, won't read CD's....disc utilities shows disc unavailable!  Rarely used and out of warranty, what a rip off!!  I have been on MACS since the 80's and things are getting more and more difficult

    Optical drive on iMac at work, barely one year old, won't read CD's....disc utilities shows disc unavailable!  Rarely used and out of warranty, what a rip off!!  I have been on MACS since the 80's and things are getting more and more difficult to deal with. Why did it quit after barely being used? Any help from Apple?

    It depends on what you mean by "barely one year old". If the iMac is only a couple of days out of warranty, Apple's been known to make exceptions and extend the warranty, though it's by no means guaranteed. If it's several days or more out of warranty, then Apple will fix it, if it's a hardware problem, but the repair won't be free. This is no different now then it would have been with a Mac purchased back in the 80s.
    Why the drive failed, if indeed it has, is impossible to say. Could have been a static shock, a weak component that failed when power was applied, or a mechanical fault in one of the tiny parts used in optical drives and hard drives that finally broke.
    Regards.

  • Is Adobe Photoshop cs3/10 still being supported?  Mac crashed and need to get up and running again.

    Is Adobe Photoshop cs3/10 still being supported?  Mac crashed and need to get up and running again.  Thank you for any info on cs3. mayord

    I believe if you were to ask Adobe Support they would tell you that CS3 is no longer supported by their services, if that is what you are refering to when you say "being supported".  That means they are not likely to offer assistance with you re-establishing it.
    But you can probably re-establish it yourself.  If you need to download it there is a place for that available:
    You can download the trial version of the software thru the page linked below and then use your current serial number to activate it.
    Be sure to follow the steps outlined in the Note: Very Important Instructions section on the download pages at this site and have cookies enabled in your browser or else the download will not work properly.
    CS3 and CS4: http://prodesigntools.com/download-adobe-cs4-and-cs3-free-trials-here.html

  • Warranty?  I went to apple for a piece of dust in my screen told me I could replace it made and appointment on 1/4/14 for 1/5/14 and couldn't get there and accidentally dropped it and cracked the screen will they still replace it?

    Warranty?  I went to apple for a piece of dust in my screen told me I could replace it. Decided to wait till after New Years. made an appointment on 1/4/14 for 1/5/14 and couldn't get there and accidentally dropped it and cracked the screen. will they still replace it?

    I know that they don't cover accidents but I went in on the Sunday before Christmas and they said I could get a replacement but I decided to wait so I could back up my iPad and now I've made 3 appointments and haven't vote to either of them and it just happened today on the 5th the day of my appointment but again couldn't make it and they replaced my iPod tough in 2011 for water damage unless they changed their warranty but thank you guys for answering :)

  • My iPhone went black and the hold the power and home button solution will not work

    My iPhone went black and the hold the power and home button solution will not work

    Make sure it's charged.
    Try to Reset your device:
        Press and hold both the Sleep/Wake button and the Home button for at least ten seconds, until the Apple logo appears (ignore the Slide to Power Off option that shows up first).

  • I have an ipod 2 generation, but it wont charger or turn on. i try pressing the power and home button at the same time but it still wouldnt work. what else should i try to do?

    One day I was going to download music from my laptop to my ipod, I was able to download all the songs I wanted but later when I try to charger my ipod it wouldn't let me. The next day I bought a new charger but it still didn't charger. I try pressing the power And home button at the same time but it still wouldn't turn on or charger.

    Try:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable              
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar                              

  • My iPhone screen won't turn on but I stil get messages and calls how can I fix it

    My phone screen won't turn on and the touch screen Doesn't work but I still get calls and messages 

    Hi Mptuck,
    Thanks for using Apple Support Communities.
    There may be a problem with your device, which could be water damage. It is best to take your device to the Apple Store and see if the Geniuses can fix it.
    Good Luck,
    -Marcus

  • I know I've heard that iPads/iPhones can't get viruses but is it possible that they can? While using my iPad, it keeps going in and out of apps. On Facebook, status and profiles keep getting clicked and it keeps zooming in and out. Can anyone help

    I Have an iPad mini, iOS 8.1. When I'm on my iPad, it keeps going in and out of random apps. Going to settings is the worse. As soon as I click settings and it opens,it starts clicking different things and tries turning on and off settings! In Facebook, profiles and status get clicked. The screen zooms in and out multiple times. It reminds me of when you call the help desk for a computer or a computer at work and they gain access and move around clicking and you're doing nothing. Basically things are being clicked and I'm not doing it.....can anyone help?

    At this point, I would go for reset to its factory default condition, using the iTunes program to get a clean system install. That way you'll clean everything out and just have it set up the way it would come from the factory. You'll need to do your backup (on the iTunes program too) and be sure you understand which stuff will be saved and which will not (from the links below). Also turn off any anti-virus program you may have on your desktop. Then when you reset it to the factory default condition, don't restore your backup just yet ... until you check it out without your data put back on it. Verify its operation first, to make sure that you know it's okay. Hopefully everything is okay at that point, otherwise you'll have to take it into Apple to check it out for any hardware failure.
    Here are the links, and the last one pertains to the reset to factory default condition ...
    Choosing an iOS Backup Method (Should I Use iTunes or iCloud to back up ...)https://support.apple.com/kb/HT5262
    Back up and Restore your iOS Device with iCloud or iTunes
    http://support.apple.com/kb/ht1766
    iTunes: About iOS Backups
    http://support.apple.com/kb/ht4946
    Create and Delete iPhone, iPad and iPod Touch Backups in iTunes
    http://support.apple.com/kb/ht4946
    iOS: Troubleshooting Encrypted Backups
    http://support.apple.com/kb/TS5162
    Use iTunes to Restore your iOS Device to Factory Settings
    http://support.apple.com/kb/ht1414

  • I can no longer change my song names like i used to. i use to be able to right click and go to "get info" and then change the song name, artist and album, now i can't is there any other way to change the songs name and info

    When I get songs and put them on my itunes accout on my computer I used to be able to rename them right clicking, going to "get info" and then renaming everything I wanted like song name, album and artwork. I also use to be able to click on the song then click and hold on it and be able to rename it. But all the songs I have gotten after the last update have not been able to be renamed in any of the old ways I use to be able to. Is there any other way to rename songs because I know I can't undo updates and that seems to be whats causing it.
    Thankyou for your time

    You are describing an iTunes problem, not an iPod touch problem. Try posing in the iTunes forum.

  • The select function in Pages and other apps gets stuck and the cursor will not move. What do I do?

    The select function in Pages and other apps gets stuck when I touch a word and the cursor will not move. What is the answer for this problem?

    Try reset iPad
    Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
    Note: Data will not be affected.

Maybe you are looking for

  • I can't update my iPhoto after upgrading to Maverick

    I just upgraded to Mavericks and ever since, my iPhoto (v. 9.2) will not work. It has a grey circle with a line through it over the application. I do see in my app store I have an update for iPhoto 11, but when I try to upgrade it and enter my apple

  • GNOME 3.2.2 black lock screen

    Ok I'm on a fully upgraded Gnome 3.2.2 arch system. If I lock the screen and walk away then come back I don't get the login prompt with my profile pic coming up anymore. The screen is blank most the time, sometimes it comes up with the time on the to

  • Material staging in production with IM and WM storage locations

    Hello, I have the following situation at hand in a Client. They use Process Orders and want to do material staging of the components. The Production Supply área is an IM managed storage location but the storage location of the components is WM manage

  • How to update keywords globally in Muse?

    Is there a way to update the keywords and have them apply to every page at once? If there is I haven't hit upon it. Thanks!

  • INVOIC01 IDoc - Map posting date

    I have a problem with the mapping of the posting date in an incoming INVOIC01 IDoc. Although the posting date is mapped on segment E1EDK03 with IDDAT = '015' (Invoice posting date (Invoice tax point date)), the resulting invoice has the system date a