G5 only boots up when monitor is unplugged?

Well hopefully someone can help? My G5 only will boot up and operate if I unplug the monitor. After it boots up I plug in the monitor everything works fine? If I try to re-start it with the monitor plugged in I it just powers up, hard drive spins, no chime, and then the fans will gradually speed up to cool the tower.
Any help would be appreciated
I discovered this by trying to eliminate hardware, to narrow it down. You can turn on the computer with the monitor (the glowing power light on the right of the screen) but that is about it.

What monitor?
What video card?
Does it power up in safe boot ok? (Sounds like it wouldn't, since you say no boot tone, but always something to try.)
How about a hot restart? Does it still stall there?
Battery age? More than a couple of years old and some weird stuff can start happening.
Does it boot into open firmware? (holding down cmd-option-O-F keys at power on) If it does that with the monitor on, then try the following two commands:
*reset-nvram <cr>*
*reset-all <r>*
and see if that helps. (You could even do that "blind" if you are a careful typist.)

Similar Messages

  • PowerMac G5 will ONLY boot up when the side panel is removed

    Hi,
    We have a PowerMac G5 Dual 2.5GHZ . This mac will ONLY boot up when the side panel and the clear plastic panel are removed. If the Mac is assembled, the Mac will start and Chime, but thats it. No display and the fans are dead quite. Any Suggestions? Thanks in advance

    Hi, I realised that this problem has ONLY occured AFTER I installed Leopard. I then reformated the hard drive and installed 10.34 ( the OS that came with the G5) and it is as good as gold. I then reformated the hard drive and installed Leopard. After a few minutes the G5 became noisy and unstable. I then reformatted the hard drive AGAIN and reinstalled 10.34 and it stable. How can I install Leopard without the machine behaving erratic? Thanks for any advice in advance

  • My presario b1900 only boots normally when a screen lid closed

    Hi im a compaq presario b1900 user and suddenly started to have a booting problem since i mistakenly closed the laptop lid in full while booting and opened it up right after.
    Then, my laptop only boots perfectly when the lid is almost closed under rougly 30 degrees - whenever i switch on my laptop with the screen lid open, it shuts down after 2 secs and automatically reboots, but then shuts down again ,and on and on.
    But after once it goes into window, it works perfectly with the lid open and works well as log-on and off at standby mode.
    It only shows a problem when booting after powered on.
    is it because my HDD got damaged from a sudden screen lid close??
    Or should i change HDD or is it a window issue??

    Thank you so much for replying; unfortunately, my screen had already gone gray by the time I read your reply and I had to take in to the Genius Bar. My laptop's up and running, but the main problem is still unknown and I'll have to buy a new one soon. Thanks again!

  • Only starts when monitor is unplugged...

    G4 Quicksilver -- dual 800 with AGP video card will only start if the Apple Cinema Display is unplugged from the card, or the card is removed from the machine.
    Also, the internal firewire ports recently went dead and were replaced by a PCI firewire card.
    Am I looking at a dead video card, or something else?

    I hooked up a monitor to the VGA port on the card and it works. Is there anything I can do with the Apple Cinema Display to find out what is wrong with it? It's old, but I'm still happy with the 22" widescreen.

  • K9n2 sli platinum will only boot/post when running single channel

    Hey
    I am having problems with the rig when i want memory to run Dual channel.
    I have tried all bios settings (or at least i think so) and all memory slot combination (or at least i think so) without any luck.
    When i put 2 sticks in dimm 1+2 I get nothing but a black screen.
    When I then turn my pc off, putting 1 stick in dimm 1 it will boot and I get the message: DQS training failed on previous boot.
    Mainboard: MSI K9N2 Sli platinum
    CPU: AMD 5600X2 Windsor 2x1mb cache
    HD: have tried with WD 250gb and hitachi 160gb sata2
    Psu: Have tried with OCZ 500W and corsair 620W
    Memory: Have tried with kingston pc5400 and Adata pc6400 both 1gb sticks
    GFX: Have tried with GF8800GTS, ATI 1800XT and GF8500GT
    CPU cooler: CM Gemini2
    Motherboard have BIOS 3.1 ( so there should be no problem with running the cpu)
    everything except for mainboard have been testet with other gear and is working 100%
    Memory passed memtest with no errors.
    Some facts
    1 stick in dimm 1 = boot/post single channel
    1 stick in dimm 2 = black screen.
    1 stick in dimm 3 = boot/post single channel
    1 stick in dimm 4 = black screen
    1 stick in dimm 1 + 2 = black screen.
    1 stick in dimm 1 + 3 = boot/post single channel
    1 stck in dimm 2 + 4 black screen
    1 stckk in dimm  3 + 4 black screen.
    1 stick in 1 + 4 = Boot/postor black screen..cant remember but for sure not dual.
    1 stick in 2 + 3 = boot/post or black screen..cant remember but for sure not dual
    I have tried:
    manual timming settings, both recommended and lower timmings.
    Auto timmings
    More volt to memory
    More volt to cpu
    Tried 800, 667, 553 and 400mhz
    Tried sli memory disabled and enabled
    Changing cpu ratio
    Tried T2 and T1
    Have tried load default settings
    load optimized settings
    everything on auto
    well, that’s just about it and don’t know what to try next.
    So if anybody have some input I would really appreciate it.
    Regards
    Jesper

    Have you done that?:
    Quote from: Stu on 13-September-09, 02:54:40
    Have you tried taking the board out of the case and setting up outside on a flat anti-static surface? Maybe there is something shorting the back of the board where the DIMM slot is.
    If no change:
    Leave just one memory stick in 1st DIMM close to CPU socket,
    ensure that system is stable the flash to the latest BIOS ==>
    http://eu.msi.com/index.php?func=downloaddetail&type=bios&maincat_no=1&prod_no=1443
    You can >>Use the MSI HQ Forum USB flasher<<
    Once done re-test.

  • My white macbook screen only works shortly when booting and when adjusting the brightness (turning it all the way down and up from there) and only stays on for seconds. any idea what to do?

    Hi. I'm having quite an issue here. My macbook screen is only lid when i boot and when i adjust the brightness of the screen (going all the way down and up from there). either way it goes black again after a few seconds. External monitor works though.
    Any ideas on how to solve this?
    Lasse

    I buy the dirty theory as well.  plug and unplug a whole bunch of times - you may be able to dislodge whatever is causing the issue.  Also - make sure the plug is fully seated - (some of the pad jacks are vert tight, and you really have to work them in).  I gather you are out of warrenty?  Blow in the hole.
    last resotr - take a toothpick, dip the end in fingernail polish, get rid of the xs, then very very gently, insert the pick and try to rub the contacts.  very gently as you do not want to bend them.

  • Bios Switches A / B only boot when OC Genie button is on. MSI Z77 Military Grade

    MSI Z77 Military Grade
    1. Bios Switches A / B only boot when OC Genie button is on.
    2. I normally use Bios B and upgraded the Bios from 17.6 to 17.12.
        Flash was successful. I don't remember if I had the OC Genie button on or not.
        But when I rebooted I couldn't get into the bios stuck at "A2" (thought I totally corrupted the bios
        until I turned on the OC Genie from the motherboard.
    However here is the quandary:
    3. Neither A or B Bios will boot without the OC Genie button on.
    4. The system will cycle twice than stop at A2
    5. Eventually I would like to have both Bios-es working optimally.
    Thanks for taking the time to read my post.

    remove power cord from the PSU and do >>Clear CMOS Guide<<

  • Qosmio X305 will only boot in safe mode or when the graphics card disabled

    Hi All
    I am having a very concerning issue with my laptop (Toshiba Qosmio X305). It will only boot in safe mode or if I disable the graphics card.
    Awhile back I upgraded the drivers for the nVidia 9800M GTX from the nVidia website, it worked fine for awhile, but then it started crashing randomly by giving me a full screen of random color then switching off. I fixed this by rolling back to the previous version of the drivers (the drivers that came with the laptop software).
    After that it working perfectly for months but yesterday my machine started crashing and I could not get it to boot correctly.
    I have completely deleted (not just a quick format) both the hard drives that came internally in the laptop and I have installed a clean version (the out of the box option) of the x64 Vista that came with the laptop from the recovery disks I created. After I did the install, it boots fine as only the standard VGA device is used, as soon as I installed the driver off the drivers and applications disk it would not boot correctly:
    Just after the status bar comes up and it is about to show the windows logo, just before login, I get a black screen. I can hear that it is booting fine and I can even log in to windows and by memory make things run, but I can't see anything. I then got the latest drivers, again from the nVidia website and they are not helping at all.
    My system is as follows (nothing has been added, its is just how I got it):
    Vista Ultimate x64
    4.00 GB RAM
    Intel Core 2 Quad
    Like I said previously it is a clean install of the operating system, I have not added any programs, except for installing and then updating the display drivers.
    Any help would be much appreciated!

    Hi buddy,
    It seems that this is a typical example, that only pretested display drivers from Toshiba should be used. Why?
    The nVidia drivers are not pretested and they dont have an overheat protection. So for me it sounds like that the nVidia driver has destroyed your graphic card. That means no driver will help you and reinstallation of the whole system too.
    I think the only option is replacing the graphic card. Therefore you should contact an authorized service provider in your country. Here you can search:
    http://www.csd.toshiba.com
    Explain the whole story and then you will see, what the technicians say. If your notebook is under warranty, hopefully this will be covered too. Normally other display drivers you have to install on your own risk
    Good luck! :)

  • Mavericks can only boot in safe mode

    In can only boot my Imac 27' (end of 2009) in safe mode.
    The problem started in Lion, when the computer suddenly froze.
    I upgraded (in safe mode) to Mavericks 10.9.2, took away all Launch Agents and Daemon that are not Apple (both in System and User's), done all the permission repairs, reset memory, fsck and turn the plug off the computer. The only thing I was not able to do is the hardware test (for some reason, the command + D to access the internet testing is not working). I have no external devices or cables attached.
    My 2TB hard drive is divided in 3 partitions. I have got 2 user accounts.
    Even with all this, I can only start in safe mode.
    Here is a copy of the log. If anyone can help, I would be grateful !
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.appstore" claims selected messages.
    Those messages may not appear in standard system log files or in the ASL database.
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.authd" sharing output destination "/var/log/system.log" with ASL Module "com.apple.asl".
    Output parameters from ASL Module "com.apple.asl" override any specified in ASL Module "com.apple.authd".
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.authd" claims selected messages.
    Those messages may not appear in standard system log files or in the ASL database.
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.bookstore" claims selected messages.
    Those messages may not appear in standard system log files or in the ASL database.
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.eventmonitor" claims selected messages.
    Those messages may not appear in standard system log files or in the ASL database.
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.install" claims selected messages.
    Those messages may not appear in standard system log files or in the ASL database.
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.iokit.power" claims selected messages.
    Those messages may not appear in standard system log files or in the ASL database.
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.mail" claims selected messages.
    Those messages may not appear in standard system log files or in the ASL database.
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.MessageTracer" claims selected messages.
    Those messages may not appear in standard system log files or in the ASL database.
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.performance" claims selected messages.
    Those messages may not appear in standard system log files or in the ASL database.
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.securityd" claims selected messages.
    Those messages may not appear in standard system log files or in the ASL database.
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.securityd" claims selected messages.
    Those messages may not appear in standard system log files or in the ASL database.
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.securityd" claims selected messages.
    Those messages may not appear in standard system log files or in the ASL database.
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.securityd" claims selected messages.
    Those messages may not appear in standard system log files or in the ASL database.
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.securityd" claims selected messages.
    Those messages may not appear in standard system log files or in the ASL database.
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.securityd" claims selected messages.
    Those messages may not appear in standard system log files or in the ASL database.
    03.05.14 11:48:37.000 syslogd[19]: Configuration Notice:
    ASL Module "com.apple.securityd" claims selected messages.
    Those messages may not appear in standard system log files or in the ASL database.
    03.05.14 11:48:37.000 kernel[0]: Longterm timer threshold: 1000 ms
    03.05.14 11:48:37.000 kernel[0]: Darwin Kernel Version 13.1.0: Thu Jan 16 19:40:37 PST 2014; root:xnu-2422.90.20~2/RELEASE_X86_64
    03.05.14 11:48:37.000 kernel[0]: vm_page_bootstrap: 2015569 free pages and 65199 wired pages
    03.05.14 11:48:37.000 kernel[0]: kext submap [0xffffff7f807a6000 - 0xffffff8000000000], kernel text [0xffffff8000200000 - 0xffffff80007a6000]
    03.05.14 11:48:37.000 kernel[0]: zone leak detection enabled
    03.05.14 11:48:37.000 kernel[0]: "vm_compressor_mode" is 4
    03.05.14 11:48:37.000 kernel[0]: standard timeslicing quantum is 10000 us
    03.05.14 11:48:37.000 kernel[0]: standard background quantum is 2500 us
    03.05.14 11:48:37.000 kernel[0]: mig_table_max_displ = 74
    03.05.14 11:48:37.000 kernel[0]: AppleACPICPU: ProcessorId=1 LocalApicId=0 Enabled
    03.05.14 11:48:37.000 kernel[0]: AppleACPICPU: ProcessorId=2 LocalApicId=2 Enabled
    03.05.14 11:48:37.000 kernel[0]: AppleACPICPU: ProcessorId=3 LocalApicId=4 Enabled
    03.05.14 11:48:37.000 kernel[0]: AppleACPICPU: ProcessorId=4 LocalApicId=6 Enabled
    03.05.14 11:48:37.000 kernel[0]: AppleACPICPU: ProcessorId=5 LocalApicId=0 Disabled
    03.05.14 11:48:37.000 kernel[0]: AppleACPICPU: ProcessorId=6 LocalApicId=0 Disabled
    03.05.14 11:48:37.000 kernel[0]: AppleACPICPU: ProcessorId=7 LocalApicId=0 Disabled
    03.05.14 11:48:37.000 kernel[0]: AppleACPICPU: ProcessorId=8 LocalApicId=0 Disabled
    03.05.14 11:48:37.000 kernel[0]: calling mpo_policy_init for TMSafetyNet
    03.05.14 11:48:37.000 kernel[0]: Security policy loaded: Safety net for Time Machine (TMSafetyNet)
    03.05.14 11:48:37.000 kernel[0]: calling mpo_policy_init for Sandbox
    03.05.14 11:48:37.000 kernel[0]: Security policy loaded: Seatbelt sandbox policy (Sandbox)
    03.05.14 11:48:37.000 kernel[0]: calling mpo_policy_init for Quarantine
    03.05.14 11:48:37.000 kernel[0]: Security policy loaded: Quarantine policy (Quarantine)
    03.05.14 11:48:37.000 kernel[0]: Copyright (c) 1982, 1986, 1989, 1991, 1993
    03.05.14 11:48:37.000 kernel[0]: The Regents of the University of California. All rights reserved.
    03.05.14 11:48:37.000 kernel[0]: MAC Framework successfully initialized
    03.05.14 11:48:37.000 kernel[0]: using 16384 buffer headers and 10240 cluster IO buffer headers
    03.05.14 11:48:37.000 kernel[0]: AppleKeyStore starting (BUILT: Jan 16 2014 20:19:00)
    03.05.14 11:48:37.000 kernel[0]: IOAPIC: Version 0x20 Vectors 64:87
    03.05.14 11:48:37.000 kernel[0]: ACPI: sleep states S3 S4 S5
    03.05.14 11:48:37.000 kernel[0]: pci (build 20:00:24 Jan 16 2014), flags 0x63008, pfm64 (36 cpu) 0xf80000000, 0x80000000
    03.05.14 11:48:37.000 kernel[0]: [ PCI configuration begin ]
    03.05.14 11:48:37.000 kernel[0]: AppleIntelCPUPowerManagement: Turbo Ratios 1144
    03.05.14 11:48:37.000 kernel[0]: AppleIntelCPUPowerManagement: (built 19:46:50 Jan 16 2014) initialization complete
    03.05.14 11:48:37.000 kernel[0]: console relocated to 0xf80010000
    03.05.14 11:48:37.000 kernel[0]: [ PCI configuration end, bridges 9, devices 21 ]
    03.05.14 11:48:37.000 kernel[0]: [ PCI configuration begin ]
    03.05.14 11:48:37.000 kernel[0]: [ PCI configuration end, bridges 10, devices 36 ]
    03.05.14 11:48:37.000 kernel[0]: FireWire (OHCI) TI ID 823f built-in now active, GUID 40d32dfffe04245e; max speed s800.
    03.05.14 11:48:37.000 kernel[0]: mcache: 4 CPU(s), 64 bytes CPU cache line size
    03.05.14 11:48:37.000 kernel[0]: mbinit: done [96 MB total pool size, (64/32) split]
    03.05.14 11:48:37.000 kernel[0]: Pthread support ABORTS when sync kernel primitives misused
    03.05.14 11:48:37.000 kernel[0]: rooting via boot-uuid from /chosen: 48B4343E-ADD2-366E-8820-219D2141D0B7
    03.05.14 11:48:37.000 kernel[0]: Waiting on <dict ID="0"><key>IOProviderClass</key><string ID="1">IOResources</string><key>IOResourceMatch</key><string ID="2">boot-uuid-media</string></dict>
    03.05.14 11:48:37.000 kernel[0]: com.apple.AppleFSCompressionTypeZlib kmod start
    03.05.14 11:48:37.000 kernel[0]: com.apple.AppleFSCompressionTypeDataless kmod start
    03.05.14 11:48:37.000 kernel[0]: handoff: unsupported os...
    03.05.14 11:48:37.000 kernel[0]: handoff: symbol mismatch...
    03.05.14 11:48:37.000 kernel[0]: com.apple.AppleFSCompressionTypeZlib load succeeded
    03.05.14 11:48:37.000 kernel[0]: com.apple.AppleFSCompressionTypeDataless load succeeded
    03.05.14 11:48:37.000 kernel[0]: AppleIntelCPUPowerManagementClient: ready
    03.05.14 11:48:37.000 kernel[0]: Got boot device = IOService:/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/SATA@1F,2/AppleIntelPchS eriesAHCI/PRT0@0/IOAHCIDevice@0/AppleAHCIDiskDriver/IOAHCIBlockStorageDevice/IOB lockStorageDriver/Hitachi HDS722020ALA330 Media/IOGUIDPartitionScheme/Macintosh HD@2
    03.05.14 11:48:37.000 kernel[0]: BSD root: disk0s2, major 1, minor 1
    03.05.14 11:48:37.000 kernel[0]: USBMSC Identifier (non-unique): 000000009833 0x5ac 0x8403 0x9833, 2
    03.05.14 11:48:37.000 kernel[0]: hfs: mounted Macintosh HD on device root_device
    03.05.14 11:48:37.000 kernel[0]: ath_get_caps[4044] rx chainmask mismatch actual 3 sc_chainmak 0
    03.05.14 11:48:37.000 kernel[0]: 2.296383: ath_get_caps[4019] tx chainmask mismatch actual 3 sc_chainmak 0
    03.05.14 11:48:37.000 kernel[0]: 2.300580: Atheros: mac 128.2 phy 13.0 radio 12.0
    03.05.14 11:48:37.000 kernel[0]: 2.300590: Use hw queue 0 for WME_AC_BE traffic
    03.05.14 11:48:37.000 kernel[0]: 2.300596: Use hw queue 1 for WME_AC_BK traffic
    03.05.14 11:48:37.000 kernel[0]: 2.300603: Use hw queue 2 for WME_AC_VI traffic
    03.05.14 11:48:37.000 kernel[0]: 2.300609: Use hw queue 3 for WME_AC_VO traffic
    03.05.14 11:48:37.000 kernel[0]: 2.300615: Use hw queue 8 for CAB traffic
    03.05.14 11:48:37.000 kernel[0]: 2.300620: Use hw queue 9 for beacons
    03.05.14 11:48:37.000 kernel[0]: 2.300700: wlan_vap_create : enter. devhandle=0xd4f8c6b0, opmode=IEEE80211_M_STA, flags=0x1
    03.05.14 11:48:37.000 kernel[0]: 2.300743: wlan_vap_create : exit. devhandle=0xd4f8c6b0, opmode=IEEE80211_M_STA, flags=0x1.
    03.05.14 11:48:37.000 kernel[0]: 2.300778: ATH tunables:
    03.05.14 11:48:37.000 kernel[0]: 2.300782:   pullmode[1] txringsize[  256] txsendqsize[1024] reapmin[   32] reapcount[  128]
    03.05.14 11:48:37.000 kernel[0]: VM Swap Subsystem is ON
    03.05.14 11:48:37.000 kernel[0]: Waiting for DSMOS...
    03.05.14 11:48:37.000 kernel[0]: IOBluetoothUSBDFU::probe
    03.05.14 11:48:37.000 kernel[0]: IOBluetoothUSBDFU::probe ProductID - 0x8215 FirmwareVersion - 0x0207
    03.05.14 11:48:37.000 kernel[0]: **** [IOBluetoothHostControllerUSBTransport][start] -- completed -- result = TRUE -- 0xb400 ****
    03.05.14 11:48:10.829 com.apple.launchd[1]: *** launchd[1] has started up. ***
    03.05.14 11:48:10.830 com.apple.launchd[1]: *** Shutdown logging is enabled. ***
    03.05.14 11:48:37.000 kernel[0]: **** [BroadcomBluetoothHostControllerUSBTransport][start] -- Completed -- 0xb400 ****
    03.05.14 11:48:37.000 kernel[0]: init
    03.05.14 11:48:37.000 kernel[0]: probe
    03.05.14 11:48:37.000 kernel[0]: start
    03.05.14 11:48:37.000 kernel[0]: [IOBluetoothHCIController][staticBluetoothHCIControllerTransportShowsUp] -- Received Bluetooth Controller register service notification -- 0xb400
    03.05.14 11:48:37.000 kernel[0]: [IOBluetoothHCIController][start] -- completed
    03.05.14 11:48:37.000 kernel[0]: SMC::smcReadKeyAction ERROR: smcReadData8 failed for key LsNM (kSMCKeyNotFound)
    03.05.14 11:48:37.000 kernel[0]: SMC::smcReadKeyAction ERROR LsNM kSMCKeyNotFound(0x84) fKeyHashTable=0x0
    03.05.14 11:48:37.000 kernel[0]: SMC::smcGetLightshowVers ERROR: smcReadKey LsNM failed (kSMCKeyNotFound)
    03.05.14 11:48:37.000 kernel[0]: SMC::smcPublishLightshowVersion ERROR: smcGetLightshowVers failed (kSMCKeyNotFound)
    03.05.14 11:48:37.000 kernel[0]: SMC::smcInitHelper ERROR: smcPublishLightshowVersion failed (kSMCKeyNotFound)
    03.05.14 11:48:37.000 kernel[0]: ** Device in slot: SLOT--1 **
    03.05.14 11:48:37.000 kernel[0]: Previous Shutdown Cause: 3
    03.05.14 11:48:37.000 kernel[0]: SMC::smcInitHelper ERROR: MMIO regMap == NULL - fall back to old SMC mode
    03.05.14 11:48:37.000 kernel[0]: DSMOS has arrived
    03.05.14 11:48:37.609 distnoted[66]: assertion failed: 13C64: liblaunch.dylib + 25164 [38D1AB2C-A476-385F-8EA8-7AB604CA1F89]: 0x25
    03.05.14 11:48:36.114 hidd[45]: void __IOHIDPlugInLoadBundles(): Loaded 0 HID plugins
    03.05.14 11:48:36.115 fseventsd[46]: event logs in /.fseventsd out of sync with volume.  destroying old logs. (502 27 1097)
    03.05.14 11:48:36.115 fseventsd[46]: log dir: /.fseventsd getting new uuid: 4CB3C308-0B39-4855-BD13-3F533C4457B9
    03.05.14 11:48:36.117 hidd[45]: Posting 'com.apple.iokit.hid.displayStatus' notifyState=1
    03.05.14 11:48:36.416 com.apple.usbmuxd[17]: usbmuxd-327.4 on Feb 12 2014 at 14:54:33, running 64 bit
    03.05.14 11:48:36.633 kdc[42]: krb5_kdc_set_dbinfo: failed to create root node: /Local/Default
    03.05.14 11:48:37.611 com.apple.launchd[1]: (com.apple.Kerberos.kdc[42]) Exited with code: 1
    03.05.14 11:48:37.000 kernel[0]: IO80211Controller::dataLinkLayerAttachComplete():  adding AppleEFINVRAM notification
    03.05.14 11:48:37.000 kernel[0]: IO80211Interface::efiNVRAMPublished(): 
    03.05.14 11:48:37.642 kdc[78]: label: default
    03.05.14 11:48:37.642 kdc[78]:     dbname: od:/Local/Default
    03.05.14 11:48:37.642 kdc[78]:     mkey_file: /var/db/krb5kdc/m-key
    03.05.14 11:48:37.642 kdc[78]:     acl_file: /var/db/krb5kdc/kadmind.acl
    03.05.14 11:48:38.242 com.apple.SecurityServer[24]: Session 100000 created
    03.05.14 11:48:38.000 kernel[0]: [IOBluetoothHCIController::setConfigState] calling registerService
    03.05.14 11:48:38.000 kernel[0]: **** [IOBluetoothHCIController][protectedBluetoothHCIControllerTransportShowsUp] -- Connected to the transport successfully -- 0x1a40 -- 0xe000 -- 0xb400 ****
    03.05.14 11:48:39.540 configd[56]: en0: DHCP duplicate configured service
    03.05.14 11:48:42.000 kernel[0]: AirPort: Link Down on en1. Reason 8 (Disassociated because station leaving).
    03.05.14 11:48:42.130 configd[56]: en0: AUTOMATIC-V6 duplicate configured service
    03.05.14 11:48:43.069 configd[56]: dhcp_arp_router: en1 SSID unavailable
    03.05.14 11:48:43.078 configd[56]: setting hostname to "Macs-iMac-3.local"
    03.05.14 11:48:43.092 configd[56]: network changed.
    03.05.14 11:48:43.095 configd[56]: en0: DHCP duplicate configured service
    03.05.14 11:48:43.095 configd[56]: en0: AUTOMATIC-V6 duplicate configured service
    03.05.14 11:48:43.000 kernel[0]: flow_divert_kctl_disconnect (0): disconnecting group 1
    03.05.14 11:48:43.492 mds[34]: (Normal) FMW: FMW 0 0
    03.05.14 11:48:44.000 kernel[0]: hfs: mounted Video on device disk0s4
    03.05.14 11:48:45.000 kernel[0]: hfs: mounted Musicas on device disk0s5
    03.05.14 11:48:46.690 com.apple.SecurityServer[24]: Entering service
    03.05.14 11:48:46.783 mDNSResponder[35]: mDNSResponder mDNSResponder-522.90.2 (Nov  3 2013 18:51:09) starting OSXVers 13
    03.05.14 11:48:46.813 digest-service[67]: label: default
    03.05.14 11:48:46.813 digest-service[67]:     dbname: od:/Local/Default
    03.05.14 11:48:46.813 digest-service[67]:     mkey_file: /var/db/krb5kdc/m-key
    03.05.14 11:48:46.814 digest-service[67]:     acl_file: /var/db/krb5kdc/kadmind.acl
    03.05.14 11:48:46.816 digest-service[67]: digest-request: uid=0
    03.05.14 11:48:46.833 UserEventAgent[11]: Captive: CNPluginHandler en1: Inactive
    03.05.14 11:48:46.835 UserEventAgent[11]: Failed to copy info dictionary for bundle /System/Library/UserEventPlugins/alfUIplugin.plugin
    03.05.14 11:48:46.870 digest-service[67]: digest-request: netr probe 0
    03.05.14 11:48:46.871 digest-service[67]: digest-request: init request
    03.05.14 11:48:46.879 digest-service[67]: digest-request: init return domain: BUILTIN server: MACS-IMAC-3 indomain was: <NULL>
    03.05.14 11:48:46.913 awacsd[59]: Starting awacsd connectivity_executables-97 (Aug 24 2013 23:49:23)
    03.05.14 11:48:46.919 awacsd[59]: InnerStore CopyAllZones: no info in Dynamic Store
    03.05.14 11:48:47.229 locationd[40]: NBB-Could not get UDID for stable refill timing, falling back on random
    03.05.14 11:48:47.243 locationd[40]: Location icon should now be in state 'Inactive'
    03.05.14 11:48:47.243 locationd[40]: locationd was started after an unclean shutdown
    03.05.14 11:48:47.401 airportd[63]: airportdProcessDLILEvent: en1 attached (up)
    03.05.14 11:48:47.000 kernel[0]: AtherosNewma40P2PInterface::init name <p2p0> role 1
    03.05.14 11:48:47.000 kernel[0]: AtherosNewma40P2PInterface::init() <p2p> role 1
    03.05.14 11:48:47.404 configd[56]: en0: DHCP duplicate configured service
    03.05.14 11:48:47.404 configd[56]: en0: AUTOMATIC-V6 duplicate configured service
    03.05.14 11:48:47.000 kernel[0]: 38.870836: performCountryCodeOperation: Not connected, scan in progress[0]
    03.05.14 11:48:47.000 kernel[0]: 38.871785: setWOW_PARAMETERS:wowevents = 2(1)
    03.05.14 11:48:47.470 mds[34]: (Warning) Server: No stores registered for metascope "kMDQueryScopeComputer"
    03.05.14 11:48:47.532 loginwindow[38]: Login Window Application Started
    03.05.14 11:48:47.000 kernel[0]: en1: 802.11d country code set to 'US '.
    03.05.14 11:48:47.000 kernel[0]: en1: Supported channels 1 2 3 4 5 6 7 8 9 10 11 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 149 153 157 161 165
    03.05.14 11:48:47.589 sandboxd[113]: ([63]) airportd(63) deny file-read-data /private/var/root/Library/Preferences/ByHost/.GlobalPreferences.506705CD-8AA9-5 340-BEA4-87BBB2A2E261.plist
    03.05.14 11:48:48.103 aosnotifyd[62]: ApplePushService: Timed out making blocking call, failed to perform call via XPC connection to 'com.apple.apsd'
    03.05.14 11:48:48.167 mdmclient[36]: ApplePushService: Timed out making blocking call, failed to perform call via XPC connection to 'com.apple.apsd'
    03.05.14 11:48:48.530 networkd[118]: networkd.118 built Aug 24 2013 22:08:46
    03.05.14 11:48:49.138 aosnotifyd[62]: ApplePushService: Timed out making blocking call, failed to perform call via XPC connection to 'com.apple.apsd'
    03.05.14 11:48:49.178 mdmclient[36]: ApplePushService: Timed out making blocking call, failed to perform call via XPC connection to 'com.apple.apsd'
    03.05.14 11:48:50.136 WindowServer[115]: Server is starting up
    03.05.14 11:48:50.229 aosnotifyd[62]: ApplePushService: Timed out making blocking call, failed to perform call via XPC connection to 'com.apple.apsd'
    03.05.14 11:48:50.262 mdmclient[36]: ApplePushService: Timed out making blocking call, failed to perform call via XPC connection to 'com.apple.apsd'
    03.05.14 11:48:50.542 systemkeychain[102]: done file: /var/run/systemkeychaincheck.done
    03.05.14 11:48:50.554 configd[56]: network changed: DNS*
    03.05.14 11:48:50.556 configd[56]: network changed: DNS*
    03.05.14 11:48:50.557 mDNSResponder[35]: D2D_IPC: Loaded
    03.05.14 11:48:50.557 mDNSResponder[35]: D2DInitialize succeeded
    03.05.14 11:48:50.561 mDNSResponder[35]:   4: Listening for incoming Unix Domain Socket client requests
    03.05.14 11:48:50.561 mDNSResponder[35]: Adding registration domain 156425616.members.btmm.icloud.com.
    03.05.14 11:48:50.568 mDNSResponder[35]: mDNS_Register_internal: ERROR!! Tried to register AuthRecord 00007FC9AB802360 Macs-iMac-3.local. (Addr) that's already in the list
    03.05.14 11:48:50.568 mDNSResponder[35]: mDNS_Register_internal: ERROR!! Tried to register AuthRecord 00007FC9AB8027F0 1.0.0.127.in-addr.arpa. (PTR) that's already in the list
    03.05.14 11:48:50.568 mDNSResponder[35]: mDNS_Register_internal: ERROR!! Tried to register AuthRecord 00007FC9AA81BD60 Macs-iMac-3.local. (AAAA) that's already in the list
    03.05.14 11:48:50.568 mDNSResponder[35]: mDNS_Register_internal: ERROR!! Tried to register AuthRecord 00007FC9AA81C1F0 1.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.8.E.F.ip6.arpa. (PTR) that's already in the list
    03.05.14 11:48:51.199 kdc[78]: KDC started
    03.05.14 11:48:51.321 aosnotifyd[62]: ApplePushService: Timed out making blocking call, failed to perform call via XPC connection to 'com.apple.apsd'
    03.05.14 11:48:51.362 mdmclient[36]: ApplePushService: Timed out making blocking call, failed to perform call via XPC connection to 'com.apple.apsd'
    03.05.14 11:48:51.520 apsd[61]: CGSLookupServerRootPort: Failed to look up the port for "com.apple.windowserver.active" (1102)
    03.05.14 11:48:51.571 awacsd[59]: Configuring lazy AWACS client: 156425616.p07.members.btmm.icloud.com.
    03.05.14 11:48:52.000 kernel[0]: [BNBMouseDevice::init][80.14] init is complete
    03.05.14 11:48:52.000 kernel[0]: [BNBMouseDevice::handleStart][80.14] returning 1
    03.05.14 11:48:52.000 kernel[0]: [AppleMultitouchHIDEventDriver::start] entered
    03.05.14 11:48:52.603 fseventsd[46]: event logs in /Volumes/Video/.fseventsd out of sync with volume.  destroying old logs. (157 8 1095)
    03.05.14 11:48:52.000 kernel[0]: [AppleMultitouchDevice::start] entered
    03.05.14 11:48:53.586 fseventsd[46]: log dir: /Volumes/Video/.fseventsd getting new uuid: DF46AA4B-9528-407F-AD85-EAC421E431C3
    03.05.14 11:48:54.638 awacsd[59]: KV HTTP 0
    03.05.14 11:48:54.655 fseventsd[46]: event logs in /Volumes/Musicas/.fseventsd out of sync with volume.  destroying old logs. (155 10 1095)
    03.05.14 11:48:55.000 kernel[0]: hfs: mounted Recovery HD on device disk0s3
    03.05.14 11:48:55.424 mds[34]: (Normal) Volume: volume:0x7f8813845200 ********** Bootstrapped Creating a default store:0 SpotLoc:(null) SpotVerLoc:(null) occlude:0 /Volumes/Recovery HD
    03.05.14 11:48:56.202 fseventsd[46]: log dir: /Volumes/Musicas/.fseventsd getting new uuid: DBDC9085-505D-4A24-8508-5C15EBF36DFA
    03.05.14 11:48:57.243 WindowServer[115]: Session 256 retained (2 references)
    03.05.14 11:48:57.243 WindowServer[115]: Session 256 released (1 references)
    03.05.14 11:48:57.280 WindowServer[115]: Session 256 retained (2 references)
    03.05.14 11:48:57.282 WindowServer[115]: init_page_flip: page flip mode is on
    03.05.14 11:48:57.000 kernel[0]: en1: BSSID changed to 10:9a:dd:82:5b:36
    03.05.14 11:48:57.000 kernel[0]: AirPort: Link Up on en1
    03.05.14 11:48:57.000 kernel[0]: 48.780691: apple80211Request[10514] Unsupported ioctl 181
    03.05.14 11:48:57.000 kernel[0]: en1: BSSID changed to 10:9a:dd:82:5b:36
    03.05.14 11:48:57.000 kernel[0]: AirPort: RSN handshake complete on en1
    03.05.14 11:48:57.000 kernel[0]: flow_divert_kctl_disconnect (0): disconnecting group 1
    03.05.14 11:48:57.927 fseventsd[46]: Logging disabled completely for device:1: /Volumes/Recovery HD
    03.05.14 11:48:57.000 kernel[0]: hfs: unmount initiated on Recovery HD on device disk0s3
    03.05.14 11:48:58.530 WindowServer[115]: Found 39 modes for display 0x00000000 [36, 3]
    03.05.14 11:48:58.533 WindowServer[115]: Found 1 modes for display 0x00000000 [1, 0]
    03.05.14 11:48:58.534 WindowServer[115]: mux_initialize: Couldn't find any matches
    03.05.14 11:48:58.535 WindowServer[115]: Found 39 modes for display 0x00000000 [36, 3]
    03.05.14 11:48:58.538 WindowServer[115]: Found 1 modes for display 0x00000000 [1, 0]
    03.05.14 11:48:59.640 awacsd[59]: KV HTTP 0
    03.05.14 11:49:00.487 configd[56]: network changed: DNS* Proxy
    03.05.14 11:49:00.487 UserEventAgent[11]: Captive: [CNInfoNetworkActive:1655] en1: SSID 'Apple Network 825b35' making interface primary (protected network)
    03.05.14 11:49:00.488 UserEventAgent[11]: Captive: CNPluginHandler en1: Evaluating
    03.05.14 11:49:00.489 UserEventAgent[11]: Captive: en1: Probing 'Apple Network 825b35'
    03.05.14 11:49:00.493 configd[56]: network changed: v4(en1!:10.0.1.5) DNS+ Proxy+ SMB
    03.05.14 11:49:02.569 ntpd[135]: proto: precision = 1.000 usec
    03.05.14 11:49:02.673 racoon[157]: accepted connection on vpn control socket.
    03.05.14 11:49:02.811 UserEventAgent[11]: Captive: CNPluginHandler en1: Authenticated
    03.05.14 11:49:03.100 apsd[61]: CGSLookupServerRootPort: Failed to look up the port for "com.apple.windowserver.active" (1102)
    03.05.14 11:49:04.537 apsd[61]: Unrecognized leaf certificate
    03.05.14 11:49:14.000 kernel[0]: utun_ctl_connect: creating interface utun0
    03.05.14 11:49:14.375 racoon[157]: failed to bind to address fd20:c40d:6b6d:9361:945f:9bfc:6bcb:cf76[500] (Can't assign requested address).
    03.05.14 11:49:14.375 racoon[157]: failed to bind to address fd20:c40d:6b6d:9361:945f:9bfc:6bcb:cf76[500]: because interface address is/was not ready (flags 2).
    03.05.14 11:49:14.375 racoon[157]: failed to bind to address fd20:c40d:6b6d:9361:945f:9bfc:6bcb:cf76[4500] (Can't assign requested address).
    03.05.14 11:49:14.375 racoon[157]: failed to bind to address fd20:c40d:6b6d:9361:945f:9bfc:6bcb:cf76[4500]: because interface address is/was not ready (flags 2).
    03.05.14 11:49:14.376 racoon[157]: failed to bind to address fd20:c40d:6b6d:9361:945f:9bfc:6bcb:cf76[500] (Can't assign requested address).
    03.05.14 11:49:14.376 racoon[157]: failed to bind to address fd20:c40d:6b6d:9361:945f:9bfc:6bcb:cf76[500]: because interface address is/was not ready (flags 2).
    03.05.14 11:49:14.377 racoon[157]: failed to bind to address fd20:c40d:6b6d:9361:945f:9bfc:6bcb:cf76[4500] (Can't assign requested address).
    03.05.14 11:49:14.377 racoon[157]: failed to bind to address fd20:c40d:6b6d:9361:945f:9bfc:6bcb:cf76[4500]: because interface address is/was not ready (flags 2).
    03.05.14 11:49:14.378 racoon[157]: failed to bind to address fd20:c40d:6b6d:9361:945f:9bfc:6bcb:cf76[500] (Can't assign requested address).
    03.05.14 11:49:14.378 configd[56]: en0: DHCP duplicate configured service
    03.05.14 11:49:14.378 racoon[157]: failed to bind to address fd20:c40d:6b6d:9361:945f:9bfc:6bcb:cf76[500]: because interface address is/was not ready (flags 2).
    03.05.14 11:49:14.378 configd[56]: en0: AUTOMATIC-V6 duplicate configured service
    03.05.14 11:49:14.378 racoon[157]: failed to bind to address fd20:c40d:6b6d:9361:945f:9bfc:6bcb:cf76[4500] (Can't assign requested address).
    03.05.14 11:49:14.378 racoon[157]: failed to bind to address fd20:c40d:6b6d:9361:945f:9bfc:6bcb:cf76[4500]: because interface address is/was not ready (flags 2).
    03.05.14 11:49:14.000 kernel[0]: flow_divert_kctl_disconnect (0): disconnecting group 1
    03.05.14 11:49:20.396 mDNSResponder[35]: ERROR: socket closed prematurely tcpInfo->nread = 0
    03.05.14 11:49:23.596 mDNSResponder[35]: ERROR: socket closed prematurely tcpInfo->nread = 0
    03.05.14 11:50:16.742 warmd[16]: [warmctl_evt_timer_bc_activation_timeout:287] BC activation bcstop timer fired!
    03.05.14 11:50:16.743 warmd[16]: [___bootcachectl_filter_out_sharedio_from_history_block_invoke:2329] Unable to open i386 shared cache: 2 No such file or directory
    03.05.14 11:50:51.617 apsd[61]: Failed to send activation record to service com.apple.ManagedClient.enroll
    03.05.14 11:51:07.187 distnoted[172]: # distnote server agent  absolute time: 177.064182367   civil time: Sat May  3 11:51:07 2014   pid: 172 uid: 502  root: no
    03.05.14 11:51:24.977 mdworker[177]: (Warning) Import: import uti:com.adobe.pdf plugin:/Library/Spotlight/PDF.mdimporter uuid:7D48EF77-69AB-47DB-BBD9-D907F89C3C17 61 exceeded cpu use limits (12) after 12997 milliseconds sizing:0 - find suspect file using: sudo mdutil -t 842802
    03.05.14 11:51:25.032 com.apple.SecurityServer[24]: Session 100003 created
    03.05.14 11:51:25.033 com.apple.SecurityServer[24]: Session 100005 created
    03.05.14 11:51:38.595 mdworker[184]: (Warning) Import: import uti:com.adobe.pdf plugin:/Library/Spotlight/PDF.mdimporter uuid:7D48EF77-69AB-47DB-BBD9-D907F89C3C17 61 exceeded cpu use limits (12) after 12980 milliseconds sizing:0 - find suspect file using: sudo mdutil -t 842802

    I have tried a few other tricks from the experts in the discussion boards (including removing all preference files that are non apple, remove all non apple extensions), still no way to start up the computer other than safe boot.
    I would like to try and turn off bonjour, as it seems like a MDNSResponder Error. But need a green light from any of you experts.
    I am posting the latest system log (on this one, I forgot to unplug the printer)
    Please help !!!
    May  4 20:38:05 localhost bootlog[0]: BOOT_TIME 1399246685 0
    May  4 20:38:44 localhost syslogd[19]: Configuration Notice:
        ASL Module "com.apple.appstore" claims selected messages.
        Those messages may not appear in standard system log files or in the ASL database.
    May  4 20:38:44 localhost syslogd[19]: Configuration Notice:
        ASL Module "com.apple.authd" sharing output destination "/var/log/system.log" with ASL Module "com.apple.asl".
        Output parameters from ASL Module "com.apple.asl" override any specified in ASL Module "com.apple.authd".
    May  4 20:38:44 localhost syslogd[19]: Configuration Notice:
        ASL Module "com.apple.authd" claims selected messages.
        Those messages may not appear in standard system log files or in the ASL database.
    May  4 20:38:44 localhost syslogd[19]: Configuration Notice:
        ASL Module "com.apple.bookstore" claims selected messages.
        Those messages may not appear in standard system log files or in the ASL database.
    May  4 20:38:44 localhost syslogd[19]: Configuration Notice:
        ASL Module "com.apple.eventmonitor" claims selected messages.
        Those messages may not appear in standard system log files or in the ASL database.
    May  4 20:38:44 localhost syslogd[19]: Configuration Notice:
        ASL Module "com.apple.install" claims selected messages.
        Those messages may not appear in standard system log files or in the ASL database.
    May  4 20:38:44 localhost syslogd[19]: Configuration Notice:
        ASL Module "com.apple.iokit.power" claims selected messages.
        Those messages may not appear in standard system log files or in the ASL database.
    May  4 20:38:44 localhost syslogd[19]: Configuration Notice:
        ASL Module "com.apple.mail" claims selected messages.
        Those messages may not appear in standard system log files or in the ASL database.
    May  4 20:38:44 localhost syslogd[19]: Configuration Notice:
        ASL Module "com.apple.MessageTracer" claims selected messages.
        Those messages may not appear in standard system log files or in the ASL database.
    May  4 20:38:44 localhost syslogd[19]: Configuration Notice:
        ASL Module "com.apple.performance" claims selected messages.
        Those messages may not appear in standard system log files or in the ASL database.
    May  4 20:38:44 localhost syslogd[19]: Configuration Notice:
        ASL Module "com.apple.securityd" claims selected messages.
        Those messages may not appear in standard system log files or in the ASL database.
    May  4 20:38:45 --- last message repeated 6 times ---
    May  4 20:38:44 localhost kernel[0]: Longterm timer threshold: 1000 ms
    May  4 20:38:44 localhost kernel[0]: Darwin Kernel Version 13.1.0: Wed Apr  2 23:52:02 PDT 2014; root:xnu-2422.92.1~2/RELEASE_X86_64
    May  4 20:38:44 localhost kernel[0]: vm_page_bootstrap: 2008481 free pages and 72287 wired pages
    May  4 20:38:44 localhost kernel[0]: kext submap [0xffffff7f807a5000 - 0xffffff8000000000], kernel text [0xffffff8000200000 - 0xffffff80007a5000]
    May  4 20:38:44 localhost kernel[0]: zone leak detection enabled
    May  4 20:38:44 localhost kernel[0]: "vm_compressor_mode" is 4
    May  4 20:38:44 localhost kernel[0]: standard timeslicing quantum is 10000 us
    May  4 20:38:44 localhost kernel[0]: standard background quantum is 2500 us
    May  4 20:38:44 localhost kernel[0]: mig_table_max_displ = 74
    May  4 20:38:44 localhost kernel[0]: AppleACPICPU: ProcessorId=1 LocalApicId=0 Enabled
    May  4 20:38:44 localhost kernel[0]: AppleACPICPU: ProcessorId=2 LocalApicId=2 Enabled
    May  4 20:38:44 localhost kernel[0]: AppleACPICPU: ProcessorId=3 LocalApicId=4 Enabled
    May  4 20:38:44 localhost kernel[0]: AppleACPICPU: ProcessorId=4 LocalApicId=6 Enabled
    May  4 20:38:44 localhost kernel[0]: AppleACPICPU: ProcessorId=5 LocalApicId=0 Disabled
    May  4 20:38:44 localhost kernel[0]: AppleACPICPU: ProcessorId=6 LocalApicId=0 Disabled
    May  4 20:38:44 localhost kernel[0]: AppleACPICPU: ProcessorId=7 LocalApicId=0 Disabled
    May  4 20:38:44 localhost kernel[0]: AppleACPICPU: ProcessorId=8 LocalApicId=0 Disabled
    May  4 20:38:44 localhost kernel[0]: calling mpo_policy_init for TMSafetyNet
    May  4 20:38:44 localhost kernel[0]: Security policy loaded: Safety net for Time Machine (TMSafetyNet)
    May  4 20:38:44 localhost kernel[0]: calling mpo_policy_init for Sandbox
    May  4 20:38:44 localhost kernel[0]: Security policy loaded: Seatbelt sandbox policy (Sandbox)
    May  4 20:38:44 localhost kernel[0]: calling mpo_policy_init for Quarantine
    May  4 20:38:44 localhost kernel[0]: Security policy loaded: Quarantine policy (Quarantine)
    May  4 20:38:44 localhost kernel[0]: Copyright (c) 1982, 1986, 1989, 1991, 1993
    May  4 20:38:44 localhost kernel[0]: The Regents of the University of California. All rights reserved.
    May  4 20:38:44 localhost kernel[0]: MAC Framework successfully initialized
    May  4 20:38:44 localhost kernel[0]: using 16384 buffer headers and 10240 cluster IO buffer headers
    May  4 20:38:44 localhost kernel[0]: AppleKeyStore starting (BUILT: Jan 16 2014 20:19:00)
    May  4 20:38:44 localhost kernel[0]: IOAPIC: Version 0x20 Vectors 64:87
    May  4 20:38:44 localhost kernel[0]: ACPI: sleep states S3 S4 S5
    May  4 20:38:44 localhost kernel[0]: AppleIntelCPUPowerManagement: Turbo Ratios 1144
    May  4 20:38:44 localhost kernel[0]: AppleIntelCPUPowerManagement: (built 19:46:50 Jan 16 2014) initialization complete
    May  4 20:38:44 localhost kernel[0]: pci (build 20:00:24 Jan 16 2014), flags 0x63008, pfm64 (36 cpu) 0xf80000000, 0x80000000
    May  4 20:38:44 localhost kernel[0]: [ PCI configuration begin ]
    May  4 20:38:44 localhost kernel[0]: console relocated to 0xf80010000
    May  4 20:38:44 localhost kernel[0]: [ PCI configuration end, bridges 9, devices 21 ]
    May  4 20:38:44 localhost kernel[0]: [ PCI configuration begin ]
    May  4 20:38:44 localhost kernel[0]: [ PCI configuration end, bridges 10, devices 36 ]
    May  4 20:38:44 localhost kernel[0]: mcache: 4 CPU(s), 64 bytes CPU cache line size
    May  4 20:38:44 localhost kernel[0]: mbinit: done [96 MB total pool size, (64/32) split]
    May  4 20:38:44 localhost kernel[0]: Pthread support ABORTS when sync kernel primitives misused
    May  4 20:38:44 localhost kernel[0]: FireWire (OHCI) TI ID 823f built-in now active, GUID 40d32dfffe04245e; max speed s800.
    May  4 20:38:44 localhost kernel[0]: rooting via boot-uuid from /chosen: 48B4343E-ADD2-366E-8820-219D2141D0B7
    May  4 20:38:44 localhost kernel[0]: Waiting on <dict ID="0"><key>IOProviderClass</key><string ID="1">IOResources</string><key>IOResourceMatch</key><string ID="2">boot-uuid-media</string></dict>
    May  4 20:38:44 localhost kernel[0]: com.apple.AppleFSCompressionTypeZlib kmod start
    May  4 20:38:44 localhost kernel[0]: com.apple.AppleFSCompressionTypeDataless kmod start
    May  4 20:38:44 localhost kernel[0]: com.apple.AppleFSCompressionTypeZlib load succeeded
    May  4 20:38:44 localhost kernel[0]: com.apple.AppleFSCompressionTypeDataless load succeeded
    May  4 20:38:44 localhost kernel[0]: AppleIntelCPUPowerManagementClient: ready
    May  4 20:38:44 localhost kernel[0]: Got boot device = IOService:/AppleACPIPlatformExpert/PCI0@0/AppleACPIPCI/SATA@1F,2/AppleIntelPchS eriesAHCI/PRT0@0/IOAHCIDevice@0/AppleAHCIDiskDriver/IOAHCIBlockStorageDevice/IOB lockStorageDriver/Hitachi HDS722020ALA330 Media/IOGUIDPartitionScheme/Macintosh HD@2
    May  4 20:38:44 localhost kernel[0]: BSD root: disk0s2, major 1, minor 2
    May  4 20:38:44 localhost kernel[0]: USBMSC Identifier (non-unique): 000000009833 0x5ac 0x8403 0x9833, 2
    May  4 20:38:44 localhost kernel[0]: hfs: mounted Macintosh HD on device root_device
    May  4 20:38:44 localhost kernel[0]: USBF:    1.518    The IOUSBFamily is having trouble enumerating a USB device that has been plugged in.  It will keep retrying.  (Port 3 of Hub at 0xfd140000)
    May  4 20:38:44 localhost kernel[0]: ath_get_caps[4044] rx chainmask mismatch actual 3 sc_chainmak 0
    May  4 20:38:44 localhost kernel[0]: 2.257313: ath_get_caps[4019] tx chainmask mismatch actual 3 sc_chainmak 0
    May  4 20:38:44 localhost kernel[0]: 2.261494: Atheros: mac 128.2 phy 13.0 radio 12.0
    May  4 20:38:44 localhost kernel[0]: 2.261504: Use hw queue 0 for WME_AC_BE traffic
    May  4 20:38:44 localhost kernel[0]: 2.261510: Use hw queue 1 for WME_AC_BK traffic
    May  4 20:38:44 localhost kernel[0]: 2.261516: Use hw queue 2 for WME_AC_VI traffic
    May  4 20:38:44 localhost kernel[0]: 2.261522: Use hw queue 3 for WME_AC_VO traffic
    May  4 20:38:44 localhost kernel[0]: 2.261529: Use hw queue 8 for CAB traffic
    May  4 20:38:44 localhost kernel[0]: 2.261534: Use hw queue 9 for beacons
    May  4 20:38:44 localhost kernel[0]: 2.261612: wlan_vap_create : enter. devhandle=0xd6b8f6b0, opmode=IEEE80211_M_STA, flags=0x1
    May  4 20:38:44 localhost kernel[0]: 2.261651: wlan_vap_create : exit. devhandle=0xd6b8f6b0, opmode=IEEE80211_M_STA, flags=0x1.
    May  4 20:38:44 localhost kernel[0]: 2.261688: ATH tunables:
    May  4 20:38:44 localhost kernel[0]: 2.261691:   pullmode[1] txringsize[  256] txsendqsize[1024] reapmin[   32] reapcount[  128]
    May  4 20:38:44 localhost kernel[0]: USBF:    4.521    The IOUSBFamily was not able to enumerate a device.
    May  4 20:38:44 localhost kernel[0]: USBF:    5.362    The IOUSBFamily is having trouble enumerating a USB device that has been plugged in.  It will keep retrying.  (Port 3 of Hub at 0xfd140000)
    May  4 20:38:44 localhost kernel[0]: USBF:    8.760    The IOUSBFamily was not able to enumerate a device.
    May  4 20:38:44 localhost kernel[0]: USBF:    9.587    The IOUSBFamily is having trouble enumerating a USB device that has been plugged in.  It will keep retrying.  (Port 3 of Hub at 0xfd140000)
    May  4 20:38:44 localhost kernel[0]: USBF:    10.418    The IOUSBFamily gave up enumerating a USB device after 10 retries.  (Port 3 of Hub at 0xfd140000)
    May  4 20:38:44 localhost kernel[0]: USBF:    10.418    The IOUSBFamily was not able to enumerate a device.
    May  4 20:38:44 localhost kernel[0]: process taskgated[13] caught causing excessive wakeups. Observed wakeups rate (per sec): 1596; Maximum permitted wakeups rate (per sec): 150; Observation period: 300 seconds; Task lifetime number of wakeups: 45036
    May  4 20:38:44 localhost kernel[0]: VM Swap Subsystem is ON
    May  4 20:38:06 localhost com.apple.launchd[1]: *** launchd[1] has started up. ***
    May  4 20:38:06 localhost com.apple.launchd[1]: *** Shutdown logging is enabled. ***
    May  4 20:38:32 localhost hidd[44]: void __IOHIDPlugInLoadBundles(): Loaded 0 HID plugins
    May  4 20:38:36 localhost hidd[44]: Posting 'com.apple.iokit.hid.displayStatus' notifyState=1
    May  4 20:38:44 localhost com.apple.SecurityServer[25]: Session 100000 created
    May  4 20:38:45 localhost distnoted[65]: # distnote server daemon  absolute time: 28.917725827   civil time: Sun May  4 20:38:33 2014   pid: 65 uid: 0  root: yes
    May  4 20:38:46 localhost revisiond[27]: sandbox cache error 3850
    May  4 20:38:46 localhost blued[57]: sandbox cache error 11: database disk image is malformed
    May  4 20:38:46 localhost ReportCrash[71]: Invoking spindump for pid=13 wakeups_rate=1596 duration=29 because of excessive wakeups
    May  4 20:38:47 localhost kernel[0]: IO80211Controller::dataLinkLayerAttachComplete():  adding AppleEFINVRAM notification
    May  4 20:38:47 localhost kernel[0]: IO80211Interface::efiNVRAMPublished(): 
    May  4 20:38:47 localhost spindump[73]: CGSLookupServerRootPort: Failed to look up the port for "com.apple.windowserver.active" (1102)
    May  4 20:38:47 localhost spindump[73]: Unable to register Stop Spinning port: 1011
    May  4 20:38:47 localhost kernel[0]: Waiting for DSMOS...
    May  4 20:38:48 localhost spindump[73]: CGSLookupServerRootPort: Failed to look up the port for "com.apple.windowserver.active" (1102)
    May  4 20:38:48 localhost kdc[42]: krb5_kdc_set_dbinfo: failed to create root node: /Local/Default
    May  4 20:38:48 localhost com.apple.launchd[1] (com.apple.Kerberos.kdc[42]): Exited with code: 1
    May  4 20:38:49 localhost kernel[0]: IOBluetoothUSBDFU::probe
    May  4 20:38:49 localhost kernel[0]: IOBluetoothUSBDFU::probe ProductID - 0x8215 FirmwareVersion - 0x0207
    May  4 20:38:49 localhost kernel[0]: **** [IOBluetoothHostControllerUSBTransport][start] -- completed -- result = TRUE -- 0xec00 ****
    May  4 20:38:49 localhost kernel[0]: **** [BroadcomBluetoothHostControllerUSBTransport][start] -- Completed -- 0xec00 ****
    May  4 20:38:49 localhost kernel[0]: init
    May  4 20:38:49 localhost kernel[0]: probe
    May  4 20:38:49 localhost kernel[0]: start
    May  4 20:38:49 localhost kernel[0]: [IOBluetoothHCIController][staticBluetoothHCIControllerTransportShowsUp] -- Received Bluetooth Controller register service notification -- 0xec00
    May  4 20:38:49 localhost kernel[0]: [IOBluetoothHCIController][start] -- completed
    May  4 20:38:49 localhost kernel[0]: ** Device in slot: SLOT--1 **
    May  4 20:38:49 localhost kernel[0]: SMC::smcReadKeyAction ERROR: smcReadData8 failed for key LsNM (kSMCKeyNotFound)
    May  4 20:38:49 localhost kernel[0]: SMC::smcReadKeyAction ERROR LsNM kSMCKeyNotFound(0x84) fKeyHashTable=0x0
    May  4 20:38:49 localhost kernel[0]: SMC::smcGetLightshowVers ERROR: smcReadKey LsNM failed (kSMCKeyNotFound)
    May  4 20:38:49 localhost kernel[0]: SMC::smcPublishLightshowVersion ERROR: smcGetLightshowVers failed (kSMCKeyNotFound)
    May  4 20:38:49 localhost kernel[0]: SMC::smcInitHelper ERROR: smcPublishLightshowVersion failed (kSMCKeyNotFound)
    May  4 20:38:49 localhost kernel[0]: Previous Shutdown Cause: 3
    May  4 20:38:49 localhost kernel[0]: SMC::smcInitHelper ERROR: MMIO regMap == NULL - fall back to old SMC mode
    May  4 20:38:49 localhost kernel[0]: [IOBluetoothHCIController::setConfigState] calling registerService
    May  4 20:38:49 localhost kernel[0]: **** [IOBluetoothHCIController][protectedBluetoothHCIControllerTransportShowsUp] -- Connected to the transport successfully -- 0x1240 -- 0x7800 -- 0xec00 ****
    May  4 20:38:49 localhost kernel[0]: DSMOS has arrived
    May  4 20:38:50 localhost com.apple.SecurityServer[25]: Entering service
    May  4 20:38:51 localhost kdc[79]: label: default
    May  4 20:38:51 localhost kdc[79]:     dbname: od:/Local/Default
    May  4 20:38:51 localhost kdc[79]:     mkey_file: /var/db/krb5kdc/m-key
    May  4 20:38:51 localhost kdc[79]:     acl_file: /var/db/krb5kdc/kadmind.acl
    May  4 20:38:52 localhost digest-service[66]: label: default
    May  4 20:38:52 localhost digest-service[66]:     dbname: od:/Local/Default
    May  4 20:38:52 localhost digest-service[66]:     mkey_file: /var/db/krb5kdc/m-key
    May  4 20:38:52 localhost digest-service[66]:     acl_file: /var/db/krb5kdc/kadmind.acl
    May  4 20:38:52 localhost kernel[0]: AirPort: Link Down on en1. Reason 8 (Disassociated because station leaving).
    May  4 20:38:52 localhost configd[55]: dhcp_arp_router: en1 SSID unavailable
    May  4 20:38:52 localhost configd[55]: network changed.
    May  4 20:38:53 Macs-iMac-3.local configd[55]: setting hostname to "Macs-iMac-3.local"
    May  4 20:38:53 Macs-iMac-3.local digest-service[66]: digest-request: uid=0
    May  4 20:38:53 Macs-iMac-3.local com.apple.usbmuxd[17]: usbmuxd-327.4 on Feb 12 2014 at 14:54:33, running 64 bit
    May  4 20:38:53 Macs-iMac-3.local mDNSResponder[35]: mDNSResponder mDNSResponder-522.90.2 (Nov  3 2013 18:51:09) starting OSXVers 13
    May  4 20:38:55 Macs-iMac-3 kernel[0]: hfs: mounted Video on device disk0s4
    May  4 20:38:56 Macs-iMac-3.local apsd[60]: CGSLookupServerRootPort: Failed to look up the port for "com.apple.windowserver.active" (1102)
    May  4 20:38:56 Macs-iMac-3.local aosnotifyd[61]: aosnotifyd has been launched
    May  4 20:38:57 Macs-iMac-3.local systemkeychain[94]: done file: /var/run/systemkeychaincheck.done
    May  4 20:38:57 Macs-iMac-3 kernel[0]: hfs: mounted Musicas on device disk0s5
    May  4 20:38:58 Macs-iMac-3.local configd[55]: network changed: DNS*
    May  4 20:38:58 --- last message repeated 1 time ---
    May  4 20:38:58 Macs-iMac-3.local stackshot[21]: Timed out waiting for IOKit to finish matching.
    May  4 20:38:58 Macs-iMac-3.local awacsd[58]: Starting awacsd connectivity_executables-97 (Aug 24 2013 23:49:23)
    May  4 20:38:59 Macs-iMac-3.local airportd[62]: airportdProcessDLILEvent: en1 attached (up)
    May  4 20:38:59 Macs-iMac-3 kernel[0]: AtherosNewma40P2PInterface::init name <p2p0> role 1
    May  4 20:38:59 Macs-iMac-3 kernel[0]: AtherosNewma40P2PInterface::init() <p2p> role 1
    May  4 20:38:59 Macs-iMac-3.local digest-service[66]: digest-request: netr probe 0
    May  4 20:38:59 Macs-iMac-3.local digest-service[66]: digest-request: init request
    May  4 20:39:00 Macs-iMac-3.local digest-service[66]: digest-request: init return domain: BUILTIN server: MACS-IMAC-3 indomain was: <NULL>
    May  4 20:39:00 Macs-iMac-3.local UserEventAgent[11]: Captive: CNPluginHandler en1: Inactive
    May  4 20:39:01 Macs-iMac-3.local loginwindow[38]: Login Window Application Started
    May  4 20:39:01 Macs-iMac-3.local UserEventAgent[11]: Failed to copy info dictionary for bundle /System/Library/UserEventPlugins/alfUIplugin.plugin
    May  4 20:39:02 Macs-iMac-3.local mDNSResponder[35]: D2D_IPC: Loaded
    May  4 20:39:02 Macs-iMac-3.local mDNSResponder[35]: D2DInitialize succeeded
    May  4 20:39:02 Macs-iMac-3.local mDNSResponder[35]:   4: Listening for incoming Unix Domain Socket client requests
    May  4 20:39:02 Macs-iMac-3.local mDNSResponder[35]: Adding registration domain 156425616.members.btmm.icloud.com.
    May  4 20:39:02 Macs-iMac-3.local kdc[79]: KDC started
    May  4 20:39:02 Macs-iMac-3.local awacsd[58]: Configuring lazy AWACS client: 156425616.p07.members.btmm.icloud.com.
    May  4 20:39:03 Macs-iMac-3.local networkd[124]: networkd.124 built Aug 24 2013 22:08:46
    May  4 20:39:03 Macs-iMac-3.local awacsd[58]: KV HTTP 0
    May  4 20:39:06 Macs-iMac-3.local apsd[60]: CGSLookupServerRootPort: Failed to look up the port for "com.apple.windowserver.active" (1102)
    May  4 20:39:08 Macs-iMac-3.local mds[34]: (Warning) Server: No stores registered for metascope "kMDQueryScopeComputer"
    May  4 20:39:09 Macs-iMac-3.local awacsd[58]: KV HTTP 0
    May  4 20:39:09 Macs-iMac-3.local spindump[73]: CGSLookupServerRootPort: Failed to look up the port for "com.apple.windowserver.active" (1102)
    May  4 20:39:10 Macs-iMac-3.local sandboxd[116] ([62]): airportd(62) deny file-read-data /private/var/root/Library/Preferences/ByHost/.GlobalPreferences.506705CD-8AA9-5 340-BEA4-87BBB2A2E261.plist
    May  4 20:39:11 Macs-iMac-3 kernel[0]: flow_divert_kctl_disconnect (0): disconnecting group 1
    May  4 20:39:11 Macs-iMac-3.local blued[57]: hostControllerOnline - Number of Paired devices = 5, List of Paired devices = (
            "00-22-41-ce-73-b2",
            "7c-d1-c3-bc-ed-9b",
            "04-f1-3e-e9-76-f5",
            "d4-88-90-f0-2d-96",
            "90-27-e4-f2-fd-53"
    May  4 20:39:12 Macs-iMac-3.local blued[57]: link key found for device: 04-f1-3e-e9-76-f5
    May  4 20:39:12 Macs-iMac-3.local blued[57]: Save link key for device: 04-f1-3e-e9-76-f5
    May  4 20:39:12 Macs-iMac-3.local blued[57]: link key found for device: 7c-d1-c3-bc-ed-9b
    May  4 20:39:12 Macs-iMac-3.local blued[57]: Save link key for device: 7c-d1-c3-bc-ed-9b
    May  4 20:39:13 Macs-iMac-3 kernel[0]: [BNBMouseDevice::init][80.14] init is complete
    May  4 20:39:13 Macs-iMac-3 kernel[0]: [BNBMouseDevice::handleStart][80.14] returning 1
    May  4 20:39:13 Macs-iMac-3 kernel[0]: [AppleMultitouchHIDEventDriver::start] entered
    May  4 20:39:13 Macs-iMac-3 kernel[0]: [AppleMultitouchDevice::start] entered
    May  4 20:39:14 Macs-iMac-3.local blued[57]: [setFeatureWithReportID] Could not set report
    May  4 20:39:19 Macs-iMac-3.local awacsd[58]: KV HTTP 0
    May  4 20:39:21 Macs-iMac-3 kernel[0]: 76.792776: setWOW_PARAMETERS:wowevents = 2(1)
    May  4 20:39:21 Macs-iMac-3.local WindowServer[118]: Server is starting up
    May  4 20:39:22 Macs-iMac-3 kernel[0]: 77.481213: performCountryCodeOperation: Not connected, scan in progress[0]
    May  4 20:39:22 Macs-iMac-3.local locationd[40]: Incorrect NSStringEncoding value 0x8000100 detected. Assuming NSASCIIStringEncoding. Will stop this compatiblity mapping behavior in the near future.
    May  4 20:39:22 Macs-iMac-3.local locationd[40]: NBB-Could not get UDID for stable refill timing, falling back on random
    May  4 20:39:22 Macs-iMac-3 kernel[0]: en1: 802.11d country code set to 'US '.
    May  4 20:39:22 Macs-iMac-3 kernel[0]: en1: Supported channels 1 2 3 4 5 6 7 8 9 10 11 36 40 44 48 52 56 60 64 100 104 108 112 116 120 124 128 132 136 140 149 153 157 161 165
    May  4 20:39:22 Macs-iMac-3.local mds[34]: (Normal) FMW: FMW 0 0
    May  4 20:39:23 Macs-iMac-3.local locationd[40]: Location icon should now be in state 'Inactive'
    May  4 20:39:24 Macs-iMac-3.local mDNSResponder[35]: mDNS_Register_internal: ERROR!! Tried to register AuthRecord 00007FE4FA01AD60 Macs-iMac-3.local. (Addr) that's already in the list
    May  4 20:39:24 Macs-iMac-3.local mDNSResponder[35]: mDNS_Register_internal: ERROR!! Tried to register AuthRecord 00007FE4FA01B1F0 1.0.0.127.in-addr.arpa. (PTR) that's already in the list
    May  4 20:39:24 Macs-iMac-3.local mDNSResponder[35]: mDNS_Register_internal: ERROR!! Tried to register AuthRecord 00007FE4FB801B60 Macs-iMac-3.local. (AAAA) that's already in the list
    May  4 20:39:24 Macs-iMac-3.local mDNSResponder[35]: mDNS_Register_internal: ERROR!! Tried to register AuthRecord 00007FE4FB801FF0 1.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.8.E.F.ip6.arpa. (PTR) that's already in the list
    May  4 20:39:27 Macs-iMac-3 kernel[0]: en1: BSSID changed to 10:9a:dd:82:5b:36
    May  4 20:39:27 Macs-iMac-3 kernel[0]: AirPort: Link Up on en1
    May  4 20:39:27 Macs-iMac-3 kernel[0]: 83.354881: apple80211Request[10514] Unsupported ioctl 181
    May  4 20:39:27 Macs-iMac-3 kernel[0]: en1: BSSID changed to 10:9a:dd:82:5b:36
    May  4 20:39:27 Macs-iMac-3 kernel[0]: AirPort: RSN handshake complete on en1
    May  4 20:39:28 Macs-iMac-3.local WindowServer[118]: Session 256 retained (2 references)
    May  4 20:39:28 Macs-iMac-3.local WindowServer[118]: Session 256 released (1 references)
    May  4 20:39:28 Macs-iMac-3.local WindowServer[118]: Session 256 retained (2 references)
    May  4 20:39:28 Macs-iMac-3.local WindowServer[118]: init_page_flip: page flip mode is on
    May  4 20:39:28 Macs-iMac-3 kernel[0]: flow_divert_kctl_disconnect (0): disconnecting group 1
    May  4 20:39:29 Macs-iMac-3.local WindowServer[118]: Found 39 modes for display 0x00000000 [36, 3]
    May  4 20:39:29 Macs-iMac-3.local WindowServer[118]: Found 1 modes for display 0x00000000 [1, 0]
    May  4 20:39:29 Macs-iMac-3.local WindowServer[118]: mux_initialize: Couldn't find any matches
    May  4 20:39:29 Macs-iMac-3.local WindowServer[118]: Found 39 modes for display 0x00000000 [36, 3]
    May  4 20:39:29 Macs-iMac-3.local WindowServer[118]: Found 1 modes for display 0x00000000 [1, 0]
    May  4 20:39:30 Macs-iMac-3.local configd[55]: network changed: DNS* Proxy
    May  4 20:39:30 Macs-iMac-3.local UserEventAgent[11]: Captive: [CNInfoNetworkActive:1655] en1: SSID 'Apple Network 825b35' making interface primary (protected network)
    May  4 20:39:30 Macs-iMac-3.local UserEventAgent[11]: Captive: CNPluginHandler en1: Evaluating
    May  4 20:39:30 Macs-iMac-3.local UserEventAgent[11]: Captive: en1: Probing 'Apple Network 825b35'
    May  4 20:39:30 Macs-iMac-3.local configd[55]: network changed: v4(en1!:10.0.1.5) DNS+ Proxy+ SMB
    May  4 20:39:31 Macs-iMac-3.local racoon[146]: accepted connection on vpn control socket.
    May  4 20:39:32 Macs-iMac-3.local ntpd[132]: proto: precision = 1.000 usec
    May  4 20:39:32 Macs-iMac-3.local UserEventAgent[11]: Captive: CNPluginHandler en1: Authenticated
    May  4 20:39:33 Macs-iMac-3.local apsd[60]: Unrecognized leaf certificate
    May  4 20:39:35 Macs-iMac-3.local mds_stores[129]: (/private/var/folders/zz/zyxvpxvq6csfxvn_n0000000000000/T)(Error) IndexCI in void _indexEmergencyUnmap(void *):live.1. marking invalid
    May  4 20:39:43 --- last message repeated 1 time ---
    May  4 20:39:43 Macs-iMac-3 kernel[0]: utun_ctl_connect: creating interface utun0
    May  4 20:39:43 Macs-iMac-3.local racoon[146]: failed to bind to address fd20:c40d:6b6d:9361:80a:aacb:6d80:2d86[500] (Can't assign requested address).
    May  4 20:39:43 Macs-iMac-3.local racoon[146]: failed to bind to address fd20:c40d:6b6d:9361:80a:aacb:6d80:2d86[500]: because interface address is/was not ready (flags 2).
    May  4 20:39:43 Macs-iMac-3.local racoon[146]: failed to bind to address fd20:c40d:6b6d:9361:80a:aacb:6d80:2d86[4500] (Can't assign requested address).
    May  4 20:39:43 Macs-iMac-3.local racoon[146]: failed to bind to address fd20:c40d:6b6d:9361:80a:aacb:6d80:2d86[4500]: because interface address is/was not ready (flags 2).
    May  4 20:39:43 Macs-iMac-3.local racoon[146]: failed to bind to address fd20:c40d:6b6d:9361:80a:aacb:6d80:2d86[500] (Can't assign requested address).
    May  4 20:39:43 Macs-iMac-3.local racoon[146]: failed to bind to address fd20:c40d:6b6d:9361:80a:aacb:6d80:2d86[500]: because interface address is/was not ready (flags 2).
    May  4 20:39:43 Macs-iMac-3.local racoon[146]: failed to bind to address fd20:c40d:6b6d:9361:80a:aacb:6d80:2d86[4500] (Can't assign requested address).
    May  4 20:39:43 Macs-iMac-3.local racoon[146]: failed to bind to address fd20:c40d:6b6d:9361:80a:aacb:6d80:2d86[4500]: because interface address is/was not ready (flags 2).
    May  4 20:39:43 Macs-iMac-3.local racoon[146]: failed to bind to address fd20:c40d:6b6d:9361:80a:aacb:6d80:2d86[500] (Can't assign requested address).
    May  4 20:39:43 Macs-iMac-3.local racoon[146]: failed to bind to address fd20:c40d:6b6d:9361:80a:aacb:6d80:2d86[500]: because interface address is/was not ready (flags 2).
    May  4 20:39:43 Macs-iMac-3.local racoon[146]: failed to bind to address fd20:c40d:6b6d:9361:80a:aacb:6d80:2d86[4500] (Can't assign requested address).
    May  4 20:39:43 Macs-iMac-3.local racoon[146]: failed to bind to address fd20:c40d:6b6d:9361:80a:aacb:6d80:2d86[4500]: because interface address is/was not ready (flags 2).
    May  4 20:39:43 Macs-iMac-3 kernel[0]: flow_divert_kctl_disconnect (0): disconnecting group 1
    May  4 20:40:25 Macs-iMac-3.local warmd[16]: [warmctl_evt_timer_bc_activation_timeout:287] BC activation bcstop timer fired!
    May  4 20:40:25 Macs-iMac-3.local warmd[16]: [___bootcachectl_filter_out_sharedio_from_history_block_invoke:2329] Unable to open i386 shared cache: 2 No such file or directory
    May  4 20:40:31 Macs-iMac-3 kernel[0]: considerRebuildOfPrelinkedKernel com.apple.kext.OSvKernDSPLib triggered rebuild
    May  4 20:40:42 Macs-iMac-3.local com.apple.kextcache[154]: kext com.jmicron.JMicronATA  101069000 is in exception list, allowing to load
    May  4 20:40:49 Macs-iMac-3.local com.apple.kextcache[154]: kext com.ATTO.driver.ATTOExpressSASRAID  307029000 is in exception list, allowing to load
    May  4 20:40:49 Macs-iMac-3.local com.apple.kextcache[154]: kext com.ATTO.driver.ATTOExpressSASHBA3  100059000 is in exception list, allowing to load
    May  4 20:40:49 Macs-iMac-3.local com.apple.kextcache[154]: kext com.ATTO.driver.ATTOExpressSASHBA  200009000 is in exception list, allowing to load
    May  4 20:40:49 Macs-iMac-3.local com.apple.kextcache[154]: kext com.ATTO.driver.ATTOExpressPCIUl4  404029000 is in exception list, allowing to load
    May  4 20:40:49 Macs-iMac-3.local com.apple.kextcache[154]: kext com.ATTO.driver.ATTOCelerityFC  304089000 is in exception list, allowing to load
    May  4 20:40:55 Macs-iMac-3.local com.apple.kextcache[154]: kext com.Accusys.driver.Acxxx  300029000 is in exception list, allowing to load
    May  4 20:41:16 Macs-iMac-3.local com.apple.kextcache[154]: Created prelinked kernel /System/Library/Caches/com.apple.kext.caches/Startup/kernelcache.
    May  4 20:42:17 Macs-iMac-3.local distnoted[161]: # distnote server agent  absolute time: 252.755084619   civil time: Sun May  4 20:42:17 2014   pid: 161 uid: 502  root: no
    May  4 20:42:18 Macs-iMac-3.local mdworker[157]: sandbox cache error 3850
    May  4 20:42:37 Macs-iMac-3.local distnoted[169]: # distnote server agent  absolute time: 272.385323107   civil time: Sun May  4 20:42:37 2014   pid: 169 uid: 89  root: no
    May  4 20:42:38 Macs-iMac-3.local com.apple.SecurityServer[25]: Session 100005 created
    May  4 20:42:38 Macs-iMac-3.local com.apple.SecurityServer[25]: Session 100004 created
    May  4 20:42:50 Macs-iMac-3.local mds[34]: (Normal) Volume: volume:0x7faf09848800 ********** Bootstrapped Creating a default store:0 SpotLoc:(null) SpotVerLoc:(null) occlude:0 /Volumes/firmwaresyncd.vXiC4Y
    May  4 20:45:38 localhost bootlog[0]: BOOT_TIME 1399247138 0

  • G5 only boots to desktop image & Finder toolbar, then beachball just spins

    My G5 only boots as far as the background image showing up on both monitors and the Finder toolbar loads but I can't click on anything in it, and the beachball justs sits there and spins…I tried DiskUtilities on OS X DVD but get 'Verify volume failed with error Could not unmount disk'. Then while trying other options got 'The underlying task reported failure on exit'. I tried to boot in Safe Mode, but when I release shift key after the grey screen and spinning wheel starts, the computer just shuts down. I have a 150GB HD that came with the computer. I installed a Maxtor 500GB drive in the second bay a couple of days ago. I've only had time to transfer about 45gigs of iTunes to it. But I had no problems with playing tunes from it yesterday. I worked with Photoshop CS2 a little bit this morning then shut the computer down. This evening it won't fully boot. Any ideas of how to get it back on track?
    G5 Dual 2.0 GHz   Mac OS X (10.4.9)  
    G5 Dual 2.0 GHz   Mac OS X (10.4.9)  

    Thanks! It has become apparent that I do indeed have
    a few hours to kill before Diskwarrior hopefully
    works it's magic. In the meantime I checked out
    MacOSG.com, lots of interesting stuff and very
    informative. I have had issues on this G4 I'm working
    on now with garbled type on some websites so I
    downloaded a copy of Font Finagler as recommended on
    your site. But it didn't resolve the issue. I suppose
    with this time of reflection while I await to see if
    I'll have a repaired disk when DW is done, I can go
    through fonts and start trashing fonts and see if I
    can resolve that! Thanks again for your advice on my
    disk issue.
    Give FontNuke a shot.
    http://www.macosg.com/group/viewtopic.php?t=12960
    -Bmer
    Mac Owners Support Group
    Join Us @ MacOSG.com
    ITMS: MacOSG Podcast
     An Apple User Group 
    Disclaimer required by Apple Discussions Terms of Use: MacOSG - a non-profit Apple User Group - may receive some form of compensation, financial or otherwise, from my recommendation or link.

  • My iMacG5 will only boot to white screen, gray apple and spinning gear. Help?

    My iMacG5 will only boot to white screen, gray apple and spinning gear. Help?
    Also not totally sure if it's an Intel based computer, but that's what I recall. Any way to check, since I can't get to About This Mac window?
    It's running on OSX Leopard 10.5.4
    First symptom = running slowly - then it kind of froze with color wheel spinning - thought a forced shut down would help - help power button til off, then white screen, gray apple and spinning gear.
    Have tried...
    1. Turn off the computer by choosing Shut Down from the Apple menu, or by holding the power button until the computer turns off.
    2. Unplug all cables from the computer, including the power cord.
    3. Wait 10 seconds.
    4. Plug in the power cord while simultaneously pressing and holding the power button on the back of the computer.
    5. Let go of the power button.
    6. Press the power button once more to start up your iMac.
    Then try booting from your install disc again.
    - No change
    And...
    Booting From An OS X Installer Disc
      1. Insert OS X Installer Disc into the optical drive.
      2. Restart the computer.
      3. Immediately after the chime press and hold down the "C" key.
      4. Release the key when the spinning gear below the dark gray Apple logo
          appears.
      5. Wait for installer to finish loading.
    - The fan just got louder.
    Thanks for your help.

    You need to do an Erase and Install or an Archive and Install depending on whether the hard drive is OK or needs to be reformatted.
    Start by booting from your Leopard DVD. The rest is just following directions.
    How to Perform an Archive and Install
    An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
    1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
    Repairing the Hard Drive and Permissions
    Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
    3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
    4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
    5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
    6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.

  • Mac won't boot after power chord became unplugged accidently.

    Mac won't boot after power chord became unplugged accidently.
    I have a Mac Mini running very latest version of OSX. I was making a recording with QuickTime; when I needed to plug in a USB recording device into the back of the Mac Mini, as I pulled the Mac off my shelf to do this, the power cable came out and the Mac lost power.
    I plugged it back in and powered up the Mac. I get the grey screen with Apple logo and the spinning grey wheel; then it goes to a blue screen (as usual) and I get the "starting OSX..." progress bar. When the progress bar finishes, I'm left with a blue screen only, no dock, no apple icon at top left, nothing across the top, no nothing.
    So far, I've booted from the original disc and repaired the permissions as well as the disc, then re-booted, but same old blue screen.
    I have another iMac G5 machine, so is there any way I can at least retrieve the important HD files from the Mac Mini to my G5, before throwing the broken Mac Mini away?
    Can anyone advise please?

    Hi, Nigel.
    Not to differ with my colleagues here, but there's an important question that wasn't asked.
    1. You wrote: "So far, I've booted from the original disc and repaired the permissions as well as the disc, then re-booted, but same old blue screen."Did Disk Utility report any errors it could not fix when you ran Repair Disk? I suggest you run the procedure specified in my "Resolving Disk, Permission, and Cache Corruption" FAQ. Perform the steps therein in the order specified.
    2. You may also want to run the Apple Hardware Test that came with your Mini to be sure nothing shorted when the power cable was removed from the computer. I've seen it happen, hence I usually recommend removing the power cable at the wall before disconnecting the power cable from the computer. See my "Apple Hardware Test" FAQ.
    3. Repair Disk gives your Mini a clean bill of health, the blue screen may be the result of some Startup or Login item that was corrupted due to the sudden power outage. My "Troubleshooting Startup and Login Items" FAQ can help you pin that down if such an item is causing the problem and may help you avoid and Archive and Install.
    4. If you elect to go the Archive and Install route, see my "General advice on performing an Archive and Install" FAQ for some important tips on this process.
    5. As FYI, this is the kind of problem that makes one glad they've implemented a comprehensive backup and recovery solution. For advice on the backup and recovery solution I employ, see my "Backup and Recovery" FAQ. Computing without a comprehensive backup and recovery solution is like driving without auto insurance.
    Good luck!
    Dr. Smoke
    Author: Troubleshooting Mac® OS X
    Note: The information provided in the link(s) above is freely available. However, because I own The X Lab™, a commercial Web site to which some of these links point, the Apple Discussions Terms of Use require I include the following disclosure statement with this post:
    I may receive some form of compensation, financial or otherwise, from my recommendation or link.

  • Mac Pro only booting with option key down

    I have an 8-core mac pro that is great except for some odd booting issues. I have 3 internal drives, one with OSX 10.4.9 on it, the other with just files and the last with windows XP. I also, at times, have USB drives (or an iPod) plugged into the mac. When I restart, even if I have selected a boot volume in the startup settings, the machine will just go black. Sometimes it will play the startup chime multiple times, other times only once or not at all. The only way to get it to boot up into osx or windows is to hold down options. Even then, it only seems to work if I unplug all external drives from the machine. Any ideas whats going on or how I might fix this?
    Thanks!

    If you remove all of your USB/FireWire devices will your start up issue go away. What about resetting PRAM…
    http://docs.info.apple.com/article.html?artnum=2238

  • My macbook pro will only boot in safe mode

    Hey,
    I have a macbook pro 15-inch, Early 2011 running osx 10.9.4. I have a SSD hard drive that i installed myself a year ago and hasn't shown any defects. Its a 120 gb OCZ-AGILITY3.
    My problem:
    My macbook will only boot in safe mode nowadays. I have done a complete erasion of my hard drive and installed osx mavericks twice already. After the installation the computer will safely go to the desktop. But if i then do a reboot it won't get further than after the first apple logo, sometime the turning wheel will pop up, before turning off and trying again. i have tried resetting PRAM, I have tried resetting SMC, i have tried avoiding SMC (with big fan rate), but all with no success.
    I have done a complete hardware test (the longer one) and it showed "no troubles found".
    My guess is that the problem is with the battery. My computer won't run anymore without the adapter, when i pull the adapter out it either stays on for a while before just turning off. Without having it plugged in it won't start. Is it possible that during normal start up there is some kind of communication with the battery that can cause this?
    I ran a diagnostic shown in this thread (Will only boot in safe mode) and included it in this post.
    Hope someone can help me out.
    Thanks,
    Bram
    Start time: 17:07:42 08/25/14
    Model Identifier: MacBookPro8,2
    System Version: OS X 10.9.4 (13E28)
    Kernel Version: Darwin 13.3.0
    Boot Mode: Safe
    Time since boot: 10 minutes
    Battery
      Condition: Replace Now
    Diagnostic reports
      2014-08-25 UserEventAgent crash
    Log
      Aug 26 00:41:52 Previous Shutdown Cause: -128
      Aug 25 16:23:38 smb1_treeconnect_internal: Malformed tree connect with a bad word count! wc= 2
      Aug 25 16:24:05 process rpcsvchost[94] thread 917 caught burning CPU! It used more than 50% CPU (Actual recent usage: 99%) over 180 seconds. thread lifetime cpu usage 100.014147 seconds, (82.533432 user, 17.480715 system) ledger info: balance: 90006319931 credit: 100003230498 debit: 9996910567 limit: 90000000000 (50%) period: 180000000000 time since last refill (ns): 90079246240
      Aug 25 16:25:50 smb1_treeconnect_internal: Malformed tree connect with a bad word count! wc= 2
      Aug 25 16:58:05 jnl: b(1, 3): replay_journal: from: 9340928 to: 9773056 (joffset 0x37a000)
      Aug 25 16:58:05 jnl: b(1, 3): examining extra transactions starting @ 9773056 / 0x952000
      Aug 25 16:58:05 jnl: b(1, 3): txn starting at 9773056 (9773056) @ index  80 bnum 2696544 (8192) with disk cksum != blhdr cksum (0x93b69228 0xc647562)
      Aug 25 16:58:05 jnl: 0x662b0000 0x451b0000 0x2a0001ff 0x40000000  0xd7330300 0x46001d00 0x6c006f00 0x65006400
      Aug 25 16:58:05 jnl: b(1, 3): restarting journal replay (9340928 - 9773056)!
      Aug 25 16:58:05 jnl: b(1, 3): replay_journal: from: 9340928 to: 9773056 (joffset 0x37a000)
      Aug 25 16:58:05 jnl: b(1, 3): journal replay done.
      Aug 25 16:58:06 Previous Shutdown Cause: -128
      Aug 25 16:59:26 smb1_treeconnect_internal: Malformed tree connect with a bad word count! wc= 2
      Aug 25 16:59:59 smb1_treeconnect_internal: Malformed tree connect with a bad word count! wc= 2
    Activity
      CPU: user 17%, system 4%
    CPU per process: WindowServer (UID 0) is using 30.5  %
    launchd
      /System/Library/LaunchAgents/com.apple.AirPortBaseStationAgent.plist
      - com.apple.AirPortBaseStationAgent
    Contents of /System/Library/LaunchAgents/com.apple.AirPortBaseStationAgent.plist (XML  document text)
      <?xml version="1.0" encoding="UTF-8"?>
      <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
      <plist version="1.0">
      <dict>
      <key>Label</key>
      <string>com.apple.AirPortBaseStationAgent</string>
      <key>EnableTransactions</key>
      <true/>
      <key>LowPriorityIO</key>
      <true/>
      <key>LimitLoadToSessionType</key>
      <string>Aqua</string>
      <key>POSIXSpawnType</key>
      <string>Background</string>
      <key>LaunchEvents</key>
      <dict>
      <key>com.apple.distnoted.matching</key>
      <dict>
      <key>com.apple.airport.agent.prefschanged</key>
      <dict>
      <key>Name</key>
      <string>com.apple.airport.agent</string>
      </dict>
      </dict>
      <key>com.apple.bonjour.events</key>
      ...and 21 more line(s)
    Spotlight: Indexing and searching disabled
    Font issues: 11
    Wi-Fi
      link auth: wpa-psk
    Restricted files: 1
    Elapsed time (s): 278

    Actually it sometimes gets a little further, the display will dim and the pointer will appear and then whoop it will turn off. if i do a verbose start up, it will finish all the steps, the white screen will appear and dim and then it will turn off.

  • 24" iMac will only boot in safe mode

    Here is the short version:
    I have a 24" iMac Core 2 2.16 GHZ with Lion installed (has been for a long time).  It will only boot successfully in safe mode.  The AHT Extended tests do not report any problems.  I have reset PRAM and SMC.  Nothing helps.  Normal boot process will get to the point where it switches from the Apple logo with spinning wheel to where it would normally switch the OSX GUI and login screen.  Instead the screen is all white or gray.  The exact same problem happens if I try to boot from an OSX Install DVD or USB and also my DiskWarrior DVD.  Since safe mode works, my guess is that the problem is with the video card and the normal color depth that the Mac boots to.  In Safe Mode it is in reduced colors.
    Since safe mode works, I have all of my data backed up to an external drive.  If I could boot from an install disk, I would have already wiped the disk and done a new install, but I cannot do this!  I am assuming this is a hardware problem and given the age of this iMac I am out of luck.  I ordered a new system last night, but if it is possible to get this one working again, I would like to be able to give it to a relative who could use it.  So if anyone has any ideas, it would be appreciated.
    Just slightly longer version:
    Been using this system since 2007.  Used to use it for work, now it is the home media hub where we sync our iOS devices.  It has had Lion installed for probably a year now and has always worked great.  A few weeks ago, it started locking up whenever my son was playing Minecraft.  I would have to power off the system to get it back.  I assumed it was a Java problem.  I tried fixing disk permissions etc. but nothing solved it.  Anyway, last week I was downloading App updates in iTunes when the system locked up again.  The mouse would move around but I could not Force Quit anything or really do anything.  So I had to power off the system.  That is when the boot problems started.  Since that happened, the system has not come back with a normal boot.
    Thanks for any ideas/help.  If someone thinks this is fixable, I can bring it to my local Apple service dealer.  I do not want to pay them $100 just to have them tell me it cannot be fixed or needs a new logic board or something like that which would not be worth buying.
    Mark

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It won’t solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    Third-party system modifications are a common cause of usability problems. By a “system modification,” I mean software that affects the operation of other software — potentially for the worse. The following procedure will help identify which such modifications you've installed. Don’t be alarmed by the complexity of these instructions — they’re easy to carry out and won’t change anything on your Mac.
    These steps are to be taken while booted in safe mode.
    Below are instructions to enter some UNIX shell commands. The commands are harmless, but they must be entered exactly as given in order to work. If you have doubts about the safety of the procedure suggested here, search this site for other discussions in which it’s been followed without any report of ill effects.
    The commands may line-wrap or scroll in your browser, but each one is really just a single line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, and you can then either copy or drag it. The headings “Step 1” and so on are not part of the commands.
    Launch the Terminal application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
    When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign (“$”) or a percent sign (“%”). If you get the percent sign, enter “sh” and press return. You should then get a new line ending in a dollar sign.
    Step 1
    Triple-click the line of text below to select it. Copy the selected text to the Clipboard (command-C). Then click anywhere in the Terminal window and paste (command-V).
    find /Sy*/L*/Ex* -type f -name Info.plist -exec sh -c '/usr/libexec/PlistBuddy -c "Print :CFBundleIdentifier" "$1" 2> /dev/null | egrep -qv "apple|Accusys|ArcMSR|ATTO|CalDigit|HighPoint|hp-fax|JMicron|print|SoftRAID|stex" && echo ${1%*.kext/*}.kext' {} {} \;
    Post the lines of output (if any) that appear below what you just entered (the text, please, not a screenshot.) You can omit the final line ending in “$”.
    Step 2
    Repeat with this line:
    ls -1A /e*/mach* {,/}L*/{Ad,Compon,Ex,Fram,In,Keyb,La,Mail/Bu,P*P,Priv,Qu,Scripti,Servi,Spo,Sta}* L*/Fonts 2> /dev/null
    Important: If you formerly synchronized with a MobileMe account, your me.com email address may appear in the output of the above command. If so, anonymize it before posting.
    Step 3
    osascript -e 'tell application "System Events" to get name of every login item' 2> /dev/null
    Remember, these steps are all copy-and-paste — no typing. Also remember to post the output.
    You can then quit Terminal.

Maybe you are looking for