G5 will not boot from system disk or from Tech Tool Pro 5
Hi everyone - Having a bit of trouble and hoped I might find some answers here.
I suspect my system drive was having some issues as it sounded like it was being taxed and strained as I would open up applications from it. Upon verifying the disk using Disk Utilities, the test would stop short with the following message:
First Aid Failed
Disk Utility stopped verifying "Macintosh HD" because the following error was encountered
Filesystem verify or repair failed
In addition, an error message came up (in red) on the disk utility screen as well saying:
Volume header needs minor repair
The volume Macintosh HD needs to be repaired
Error: Filesystem verify or repair failed
Normally from here, I'd start up the computer from the Tech Tool Pro 5 disk (holding down C key upon restart). But when I did this, the computer never responded. Instead, the power was on but the screens went black and the computer went into a very quiet "idle" mode.
After about a minute, the fans began ramping up pretty high (and loud). This went on until I finally had to manually shut down the computer by holding the power switch down for a few seconds. I didn't know what else to do. Those fans were not coming down (not even after 10 minutes).
Anyway, I pushed the power button again and held the C key down. Still, nothing.... The fans stayed idle, for a little while and then ramped up again just like last time. I hit that same dead end and powered down the computer via the power button.
Is there an alternate way to boot the computer from Tech Tool Pro or the original start up disks? I'm having no luck, here.
I'm on my way into town to purchase a new internal drive (something with about 1TB of space) so that my pro apps can swim a little instead of being being bogged down on a 250G drive.
Thanks for any assistance, folks!
Oh yeah.... Happy New Year to everyone!!
Steve
The Install disk has version 10.4 on it. I have also tried booting from my OS 10.5 disk but with no avail.
However, here is an update on my plight.
Apple tech says that after hearing the symptoms, he thinks that one of the processors is shot. Being that my particular model of G5 (dual 2.7 processors) is a liquid cooled machine, it's possible that some sort of leak has formed and has either taken out a processor or has caused a processor to overheat. He says that this model of G5 has been known to do that. In this case, nothing will boot which makes me think that my original system drive may actually be okay. I'm taking it in for the tech to look at it and just be sure that's the problem. However, if it is a dead processor, the part alone would run $799 plus labor to install it. Frankly, that's just too much for me to pay to keep this old G5. I'd rather put that money towards a new or reconditioned Mac Pro 8 core or quad core machine.
I've owned several Mac computers in the past and perhaps this is the frustration talking but it seems that no matter how diligent you are in maintaining your Macintosh, these machines only seem to last about 5 years before something majorly wrong happens (mother board, processor, etc). Can I expect this same, limited time frame from a new Mac Pro? I mean, am I just being paranoid?
Similar Messages
-
I have a new macbook pro 2,6Ghz i7, 8GB 1600 Mhz internal ram, but he will not boot from an external disk with operating system Snow Leopard.
These Macs shipped with 10.7, and will run nothing older than that:
MacBook Pro
Date introduced
Original Mac OS X included
(see Tips 1 and 3)
Later Mac OS X included
(see Tip 1)
Mac OS X Build(s)
(see Tip 2)
MacBook Pro (Retina, Mid 2012)
Jun 2012
10.7.4
11E2068
MacBook Pro (15-inch, Mid 2012)
Jun 2012
10.7.4
11E2617
MacBook Pro (13-inch, Mid 2012)
Jun 2012
10.7.4
11E2617
MacBook Pro (13-inch, Late 2011)
Oct 2011
10.7.2
10.7.3
11C74, 11C2002, 11D2001
MacBook Pro (15-inch, Late 2011)
Oct 2011
10.7.2
10.7.3
11C74, 11C2002, 11D2001
MacBook Pro (17-inch, Late 2011)
Oct 2011
10.7.2
10.7.3
11C74, 11C2002, 11D2001 -
IMac will not boot from any mode except Target Disk
I have an Early 2008 Penryn iMac 24" MB398LL/A running OS X 10.7.4 (see specs below) that will not boot from ANY mode, It also has several strange vertical bars from top to bottom on the screen. They are about 10 px wide, with some pixels empty and looks a bit like a barcode if you squint at it.
I have tried Safe Boot, Force Boot, DVD Boot, FireWire/USB Boot, and it always gets to the same point. It gets to the apple screen with the spinning gear and then after about 8 seconds it freezes. The only way it works at all is in Target Disk Mode. It pops right up on my Macbook Pro and I was able to grab all my info!
I have run Disc Utilities and Tech Tool on it many times from my MBP and it passes every test.
I reformatted the HD and installed 10.7 again, it still freezes up at the same point.
I have tried using Single User mode and every time have had to run /sbin/fsck -fy twice because it always says the disk is ok but it was modified on the first pass.
I thought maybe it had a bad video card or logic board but and I ran the Apple Hardware Test on many occasions and it always passes. Recently I was told about Loop Mode and just completed running the AHT for just over 30 hours without any errors at all.
UPDATE...
Strange Part… I tried installing Mountain Lion in Target Disk Mode and everything went smoothly. When it restarted on its own the lines on the screen were gone for the moment, but the Mac still freezes up on the spinning gear and immediately restarts on its own. I have run every thing listed above on it and still nothing. Sometimes the lines reappear then in two more starts they are gone.
I did manage to have it start one time got a copy of the the error report (its at the bottom too) The Mac ran for at least 30 minutes with no problems, then the screen went crazy a few seconds and it became unresponsive. The mouse moved but that was all it could do. Now my iMac continually restarts itself, I don't have any more ideas, HELP!
Specs...
The iMac "Core 2 Duo" 3.06 24-Inch Aluminum (Early 2008/Penryn) features a 3.06 GHz Intel "Core 2 Duo" processor (E8435), with two independent processor "cores" on a single silicon chip, a 6 MB shared level 2 cache, a 1066 MHz system bus, 2 GB of RAM (800 MHz DDR2 SDRAM, PC2-6400), a 500 GB (7200 RPM) Serial ATA hard drive, a vertically-mounted slot-loading DVD±R DL "SuperDrive", NVIDIA GeForce 8800 GS graphics acceleration with 512 MB of GDDR3 memory, a built-in iSight video camera, and built-in stereo speakers underneath the 24" glossy TFT Active Matrix LCD (1920x1200 native) display.
Error Report…
Sat Sep 1 17:13:12 2012
panic(cpu 0 caller 0xffffff801a4b7b95): Kernel trap at 0xffffff7f9bab8654, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0x0000000000000010, CR3: 0x0000000011803000, CR4: 0x0000000000000660
RAX: 0x0000000000000001, RBX: 0xffffff8050e00000, RCX: 0xffffff801aa8eb00, RDX: 0xffffff80602dba38
RSP: 0xffffff80602dbb60, RBP: 0xffffff80602dbb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
R8: 0x0000000000000000, R9: 0x00000000000000ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
R12: 0xffffff8050e00000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
RFL: 0x0000000000010246, RIP: 0xffffff7f9bab8654, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x0Here is the complete error log...
Sat Sep 1 17:13:12 2012
panic(cpu 0 caller 0xffffff801a4b7b95): Kernel trap at 0xffffff7f9bab8654, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0x0000000000000010, CR3: 0x0000000011803000, CR4: 0x0000000000000660
RAX: 0x0000000000000001, RBX: 0xffffff8050e00000, RCX: 0xffffff801aa8eb00, RDX: 0xffffff80602dba38
RSP: 0xffffff80602dbb60, RBP: 0xffffff80602dbb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
R8: 0x0000000000000000, R9: 0x00000000000000ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
R12: 0xffffff8050e00000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
RFL: 0x0000000000010246, RIP: 0xffffff7f9bab8654, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x0
Backtrace (CPU 0), Frame : Return Address
0xffffff80602db800 : 0xffffff801a41d5f6
0xffffff80602db870 : 0xffffff801a4b7b95
0xffffff80602dba40 : 0xffffff801a4ce4ad
0xffffff80602dba60 : 0xffffff7f9bab8654
0xffffff80602dbb60 : 0xffffff7f9baa218c
0xffffff80602dbbb0 : 0xffffff7f9baa20e2
0xffffff80602dbbd0 : 0xffffff7f9ba73554
0xffffff80602dbc00 : 0xffffff7f9aa8d470
0xffffff80602dbc40 : 0xffffff7f9aa8d3df
0xffffff80602dbc60 : 0xffffff7f9aa926ec
0xffffff80602dbcf0 : 0xffffff7f9aa8af20
0xffffff80602dbd20 : 0xffffff7f9aadacc7
0xffffff80602dbd70 : 0xffffff801a833b9b
0xffffff80602dbdc0 : 0xffffff801a862d57
0xffffff80602dbe30 : 0xffffff801a497cef
0xffffff80602dbe80 : 0xffffff801a420abd
0xffffff80602dbeb0 : 0xffffff801a410448
0xffffff80602dbf00 : 0xffffff801a4195fb
0xffffff80602dbf70 : 0xffffff801a4a5ad6
0xffffff80602dbfb0 : 0xffffff801a4ced13
Kernel Extensions in backtrace:
com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000->0xffffff7f9aab8fff
dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
com.apple.NVDAResman(8.0)[6A699209-FB98-316B-A3C0-DCA82AA8C86B]@0xffffff7f9aad8 000->0xffffff7f9addafff
dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
dependency: com.apple.iokit.IONDRVSupport(2.3.4)[99CA4184-8D92-31B2-8726-46139E8E3DFF]@0xff ffff7f9aac4000
dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000
com.apple.GeForce(8.0)[4B9BE287-5251-398E-96B0-BB16C9BFB2D9]@0xffffff7f9ba72000 ->0xffffff7f9bb34fff
dependency: com.apple.NVDAResman(8.0.0)[6A699209-FB98-316B-A3C0-DCA82AA8C86B]@0xffffff7f9aa d8000
dependency: com.apple.iokit.IONDRVSupport(2.3.4)[99CA4184-8D92-31B2-8726-46139E8E3DFF]@0xff ffff7f9aac4000
dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
12B19
Kernel version:
Darwin Kernel Version 12.1.0: Tue Aug 14 13:29:55 PDT 2012; root:xnu-2050.9.2~1/RELEASE_X86_64
Kernel UUID: 3005059E-270B-3B9F-940D-7A66C05DDC9D
Kernel slide: 0x000000001a200000
Kernel text base: 0xffffff801a400000
System model name: iMac8,1 (Mac-F227BEC8)
System uptime in nanoseconds: 26349024446
last loaded kext at 22534854703: com.apple.driver.AppleHDAHardwareConfigDriver 2.3.0f2 (addr 0xffffff7f9c489000, size 12288)
loaded kexts:
com.apple.driver.AppleHDAHardwareConfigDriver 2.3.0f2
com.apple.driver.AppleHDA 2.3.0f2
com.apple.driver.AppleTyMCEDriver 1.0.2d2
com.apple.filesystems.autofs 3.0
com.apple.iokit.IOBluetoothSerialManager 4.0.9f8
com.apple.iokit.IOBluetoothUSBDFU 4.0.9f8
com.apple.driver.AppleLPC 1.6.0
com.apple.driver.AppleMuxControl 3.2.6
com.apple.driver.AppleBacklight 170.2.3
com.apple.driver.AppleUpstreamUserClient 3.5.10
com.apple.driver.AppleMCCSControl 1.0.33
com.apple.GeForce 8.0.0
com.apple.driver.AppleSMCPDRC 1.0.0
com.apple.iokit.IOUserEthernet 1.0.0d1
com.apple.Dont_Steal_Mac_OS_X 7.0.0
com.apple.driver.ApplePolicyControl 3.2.6
com.apple.driver.ACPI_SMC_PlatformPlugin 1.0.0
com.apple.driver.AppleIRController 320.15
com.apple.iokit.SCSITaskUserClient 3.5.1
com.apple.driver.AppleFileSystemDriver 3.0.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless 1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.BootCache 34
com.apple.driver.XsanFilter 404
com.apple.iokit.IOAHCIBlockStorage 2.2.1
com.apple.driver.AppleFWOHCI 4.9.5
com.apple.driver.AppleUSBHub 5.1.6
com.apple.driver.AirPortBrcm43224 600.36.17
com.apple.iokit.AppleYukon2 3.2.3b1
com.apple.driver.AppleAHCIPort 2.4.0
com.apple.driver.AppleIntelPIIXATA 2.5.1
com.apple.driver.AppleUSBEHCI 5.1.5
com.apple.driver.AppleUSBUHCI 5.1.5
com.apple.driver.AppleEFINVRAM 1.6.1
com.apple.driver.AppleRTC 1.5
com.apple.driver.AppleHPET 1.7
com.apple.driver.AppleACPIButtons 1.6
com.apple.driver.AppleSMBIOS 1.9
com.apple.driver.AppleACPIEC 1.6
com.apple.driver.AppleAPIC 1.6
com.apple.driver.AppleIntelCPUPowerManagementClient 196.0.0
com.apple.nke.applicationfirewall 4.0.39
com.apple.security.quarantine 2
com.apple.driver.AppleIntelCPUPowerManagement 196.0.0
com.apple.driver.DspFuncLib 2.3.0f2
com.apple.iokit.IOAudioFamily 1.8.9fc9
com.apple.kext.OSvKernDSPLib 1.6
com.apple.kext.triggers 1.0
com.apple.iokit.IOSerialFamily 10.0.6
com.apple.driver.AppleSMBusPCI 1.0.10d0
com.apple.driver.AppleBacklightExpert 1.0.4
com.apple.driver.AppleSMBusController 1.0.10d0
com.apple.nvidia.nv50hal 8.0.0
com.apple.NVDAResman 8.0.0
com.apple.iokit.IOFireWireIP 2.2.5
com.apple.driver.AppleHDAController 2.3.0f2
com.apple.iokit.IOHDAFamily 2.3.0f2
com.apple.iokit.IOSurface 86.0.2
com.apple.iokit.IOBluetoothFamily 4.0.9f8
com.apple.driver.AppleGraphicsControl 3.2.6
com.apple.iokit.IONDRVSupport 2.3.4
com.apple.iokit.IOGraphicsFamily 2.3.4
com.apple.driver.AppleSMC 3.1.3d11
com.apple.driver.IOPlatformPluginLegacy 1.0.0
com.apple.driver.IOPlatformPluginFamily 5.2.0d16
com.apple.iokit.IOUSBHIDDriver 5.0.0
com.apple.driver.AppleUSBMergeNub 5.1.5
com.apple.driver.AppleUSBComposite 5.0.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice 3.5.1
com.apple.iokit.IOBDStorageFamily 1.7
com.apple.iokit.IODVDStorageFamily 1.7.1
com.apple.iokit.IOCDStorageFamily 1.7.1
com.apple.iokit.IOATAPIProtocolTransport 3.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily 3.5.1
com.apple.iokit.IOFireWireFamily 4.5.5
com.apple.iokit.IOUSBUserClient 5.0.0
com.apple.iokit.IO80211Family 500.15
com.apple.iokit.IONetworkingFamily 3.0
com.apple.iokit.IOAHCIFamily 2.2.0
com.apple.iokit.IOATAFamily 2.5.1
com.apple.iokit.IOUSBFamily 5.1.6
com.apple.driver.AppleEFIRuntime 1.6.1
com.apple.iokit.IOHIDFamily 1.8.0
com.apple.iokit.IOSMBusFamily 1.1
com.apple.security.sandbox 220
com.apple.kext.AppleMatch 1.0.0d1
com.apple.security.TMSafetyNet 7
com.apple.driver.DiskImages 344
com.apple.iokit.IOStorageFamily 1.8
com.apple.driver.AppleKeyStore 28.18
com.apple.driver.AppleACPIPlatform 1.6
com.apple.iokit.IOPCIFamily 2.7
com.apple.iokit.IOACPIFamily 1.4
com.apple.kec.corecrypto 1.0
Model: iMac8,1, BootROM IM81.00C1.B00, 2 processors, Intel Core 2 Duo, 3.06 GHz, 2 GB, SMC 1.30f1
Graphics: NVIDIA GeForce 8800 GS, NVIDIA GeForce 8800 GS, PCIe, 512 MB
Memory Module: BANK 0/DIMM0, 1 GB, DDR2 SDRAM, 800 MHz, 0x2C00000000000000, 0x38485446313238363448445A2D3830304531
Memory Module: BANK 1/DIMM1, 1 GB, DDR2 SDRAM, 800 MHz, 0x2C00000000000000, 0x38485446313238363448445A2D3830304531
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8C), Broadcom BCM43xx 1.0 (5.10.131.36.16)
Bluetooth: Version 4.0.9f8 10405, 2 service, 18 devices, 1 incoming serial ports
Serial ATA Device: WDC WD5000AAKS-40YGA1, 500.11 GB
Parallel ATA Device: MATSHITADVD-R UJ-875
USB Device: Built-in iSight, apple_vendor_id, 0x8502, 0xfd400000 / 2
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x1a100000 / 2
USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x820f, 0x1a110000 / 5
USB Device: IR Receiver, apple_vendor_id, 0x8242, 0x5d100000 / 2
USB Device: Hub in Apple Extended USB Keyboard, apple_vendor_id, 0x1002, 0x1d100000 / 2
USB Device: Trackball, 0x046d (Logitech Inc.), 0xc404, 0x1d120000 / 4
USB Device: Apple Extended USB Keyboard, apple_vendor_id, 0x0204, 0x1d110000 / 3 -
RE: HP XP Media Center 2005 Ed will not boot from HP System Restore CD's
RE: HP XP Media Center 2005 Ed will not boot from HP System Restore CD's.
The following instructions about the "Code Purple" error FAILED. Error is still present.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
***PLAIN ENGLISH QUICK AND EASY FIX FOR ALL SYSTEMS****
***Windows 7 code purple or Windows Vista code purple***
With the code purple error on the screen, press shift+f10 (the shift key and the F10 key (at the top of the keyboard) at the same time) to open a little screen called a command prompt. (So, you get a little black screen with white text that says something about your Windows verison first and a little ways down you'll see "C:\>". It's all ready for you to start typing.)
Type the following line, just as you see it here...
notepad C:\hp\bin\checkdmi\checkdmi.cmd
so it will look like this
C:\>notepad C:\hp\bin\checkdmi\checkdmi.cmd
Press Enter.
You will see the text for the file listed in a window using a simple text editor.
Go to the beginning of the text. Press enter to make a space. Type this...
goto cleanup
So, whatever comes after, the first line looks like this...
goto cleanup
Save the file and exit notepad and restart your PC. You are good to go.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
RESULT: Same error and problem.
So, NOW THE SCENARIO IS THIS...[ And A CHALLANGE TO ALL HP Software EXPERTS]
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
1. The PC will not boot the System Restore CD's
2. The Original OS install and [HP_RECOVERY] disk sector has been severely damaged by
all of the following:
A. Massive Virus Infections as shown by Kaspersky Virus Scan and cleaned up.
B. The user had originally updated the pc to Vista Business Express Upgrade
(Supplied by HP with the original purchase and warranty).
(Prior to the upgrade, Media Center was working correctly.)
C. The original OS product key(XP Media Center Ed. 2005) has been changed by the Vista Business Express upgrade.
D. The destructve recovery done by PC-Doctor has done user file damage(s).
E. All software, and possibly hardware could be corrupted & damaged by viruses,
incomplete recovery, and the unknown failures and conditions.
To sum up, the system is locked in an unknown state, waiting for expert help.
(I can allow and manage to let someone diagnose, repair remotely using another OS i.e.Linux Opensuse 12.1, or XP Home ed if needed.)
SO IF YOU THINK YOU ARE UP TO THIS CHALLANGE, SEND MESSAGES TO DAVHPForum anytime. Thanks in advance!
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^Hello @DAVHPForum,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how you are not able to boot your computer using the HP system restore CDs, and I would be happy to assist you in this matter!
If you are not able to recover your system by following the steps in this document, please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
I hope this helps!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping! -
I have a mid-2010 27" Quad Core i5 iMac running 10.8.3. Startup disk recognizes the primary hard drive as a startup volume but will not boot from it. Have tried zapping PRAM, ran disk utility. No errors reported Any thoughts?
My bad Eric. The startup preference recognizes the primary as a 10.8.3 startup volume but when u select it the system does not boot. I can only boot from my external backup drive
-
Intel Xserve will NOT boot from hard disk drive
I have two Intel Xserves 2.0 QC machines
I have tried to re-install version 10.4.11 OS (don't ask) onto a Hard disk drive that is in a Disk drive caddy and inserted in the machine.
When booting from The installation DVD media
The disk is seen by the "Disk Utility" (the disk is partitioned as GUID boot) and the installation proceeds to the disk.
Once the first pass of the installation is complete and the system reboots, the system shows the folder and ? mark.
If I boot and hold "ALT" key to view all avaialble boot options the Hard Disk Drive does NOT appear as valid boot disk.
It does show, the still inserted Installation DVD.
I CAN boot from an external firewire drive and the Hard disk drive is visible to the OS once logged in.
I have tried different caddy postions (left, middle and right)
I have tried bona fide Apple supplied Disk drives
I have tried various different caddies
I have tried installing Operating System 10.5.* and 10.6.8 server
I have run SMC reset and system reset
But still I cannot boot off from any Hard Disk Drive inserted in a caddy at the front of the system.
Has anyone seen this behaviour?
Is it fixable?
Do I have replace something like the Hard Disk Drive back plane circuit board? Or even the main logic board?
I have now run out of ideas and cannot find any help in discussions or just googling.
ANY help would be very appreciated
Regards
TonyAntonio Hi !
QC = Quad core or QX as it is written on the "pull out" serial number tab at rear of system
I have 3 late 2006 Intel xserves
On my intial posting I declared 2 were 2.0 machines - when I was trying to be concise
2 of the macines are 2.66 systems and 1 is 2.0 system - all are QX machines
the 2.0 and 1 of the 2.66 will NOT boot from the ADM and disk inside the system - whereas the other 2.66 system will.
I have many different Caddies and these have different product/model number labels
603-9965
603-9545
603-9796
these are marked "intel SATA"
The 80Gb was only one of the drives tested - I have used Seagate 400Gb 750Gb and 1Tb - all of which have been used in systems at one time or another
and as I said the drives ARE visible once the operating system (either installation DVD or external firewire are booted from) - they are just NOT visible when the system is searching for boot media.
Thanks for the guide - I will look through that and continue to try and find an answer -
Macbook Pro will not load OS and will not boot from Install Disk
When I try to turn on my macbook pro it goes to the gray logo screen with the spinning gear however it does not progress from there and then after several minutes it proceeds to restart itself and the same process repeats itself. I have tried to boot into single user mode with success and have run /sbin/fsck -fy and that has returned that the volume appears to be ok. However, when I hit reboot it returns to the same process of the gray screen and spinning gear to black screen which repeats. When I boot into verbose mode it progresses to AppleYukon2: RxRingSize <= 1024, TxRingSize 256, RXMAXLE 1024, TXMAXLE 768, STMAXLE 3328 then it stalls for several minutes and then it shows continuing
synchronizing disks... Killing processes
then it says some other stuff to fast to read.
When I try to boot from the install disk it will not boot from holding the c key it goes through the same aforementioned cycle. When using option to boot I can see the Disk then when I select it the cycle happens again.
Also I have XP installed and I am able to boot into that successfully. Any help would be greatly appreciated.
Not sure if I left anything out
-bryceWelcome to Apple Discussions.
Do you have multiple Accounts defined on that system? The last time you successfully were running, did you run from the Account with Administrator privileges?
Do you have another computer from which you could boot and connect the Macbook Pro in Target Disk Mode to take a look at the drive from your working machine? Perhaps you can run Disk Utility from the working machine and point to the hard disk on the failing Macbook Pro.
Message was edited by: Rick Lang -
Macbook pro 17 inch early 2008 will not boot from disk
My macbook pro will not boot from from disk. I am running 10.6.8. Tried loading the disk that came with system holding down the C and you can here the drive working. It came back and said to restart computer by holding down the power button and poering it back up. Tried that and nothing. The software I tried to load is 10.5.4 Also tried loading os x snow leopard 10.6. Same thing happens.
Have you reset the SMC? If not, try that.
Intel-based Macs: Resetting the System Management Controller (SMC)
If you've done that, and it didn't help, then launch the Terminal application by entering the first few letters of its name into a Spotlight search. Copy or drag -- do not type -- the line below into the Terminal window, then press return:
pmset -g
Post any lines of output that appear below what you entered -- the text, please, not a screenshot. Then repeat with the following line:
pmset -g assertion -
Hard disk not recognised - will not boot from cd & No FW Target Disk mode
hi,
some help would be greatly appreciated.
Some time ago i was switching internal hard drives around and wound up with a kernel panic of some sort (see my previous posts).
following on from this I have tried FW target disk mode with no success, and it will not boot from a retail Tiger install disc (this machine has tiger installed (i think!). I can't force a boot from the optical drive and i also can't even force it to eject the disc inside to try another install DVD/CD (I have panther discs lying around also).
when i start up with the c key nothing happens, but when i start up with the alt/option key i get a closed padlock symbol, password entry field and a "right facing arrow" button.
anyone got any clues with this? i'm guessing it could either and/or be an internal hard drive ribbon failure (i have swapped internal HDs multiple times in this machine, which can't be good for it) or the familiar PRAM problem (although why would it not boot from an install DVD if this was the case?). I have changed the power supply unit in the past due to having a power cable snap off inside the original one - damage to PRAM caused by this?
help would be muchly appreciated!
JesseHi, Jesse. Remove the hard drive and its cable, then see whether you can start up from a CD or DVD. If that works, replace your hard drive cable.
-
Mid-2009 MacBook Pro sees internal SATA hard drive, but will not boot from or format
I inherited a Mid-2009 MacBook Pro (15-inch, 2.53 GHz model) with a very strange issue.
It first presented itself as not being able to boot from the internal SATA hard drive that came with the computer. Nothing I tried could get it to boot, so I assumed the file system was corrupted beyond repair and booted from a CD to try to format the drive. Disk Utility on the CD would not format the drive, giving me strange error messages like "Unable to write to the last block of the device".
At this point I figured the drive itself must be toast, so I pulled it out and put another known-good SATA hard drive in, booted from CD, and attempted to format. Again, same error messages and an unsuccesful format.
So I had the bright idea of formatting one of the drives in an external enclosure and then putting it in the MBP to see if OS X would even install. No dice. Get a cryptic error message before installation even begins.
So I installed OS X on the drive in the external enclosure and put it in the MBP, and it attempts to boot, but never goes anywhere.
So to sum up, the symptoms I'm seeing:
MacBook Pro CAN see internal SATA hard drives.
MacBook Pro WILL NOT boot from any internal SATA hard drive and cannot format or install OS X to any internal SATA hard drive.
MacBook Pro WILL boot from any CD or external device and seems to work properly otherwise.
At this point I'm thinking it's one of two things: the hard drive ribbon cable or the SATA controller on the logic board.
Since the MacBook Pro seems to work completely fine other than this one issue, and will boot properly from both external devices and the CD (also a SATA device), I'm thinking and hoping that it's just the hard drive ribbon cable. From my searches online, I've heard that this batch of MacBook Pros is known to have issues with the hard drive ribbon cable, but it seems in most cases this manifests itself by the Mac not being able to see a drive at all.
I've done quite a bit of troubleshooting to get to this point, but right now I'm just looking for any feedback at all. Specifically I'd love to know a way I can easily test to see whether it's the logic board or the cable.UPDATE: An interesting development!
I just tried a third known-good SATA hard drive, one which I believe supports SATA I only (but I'm not sure), and unlike the other drives that the Mac sees but cannot properly interact with, the Mac can't even see this one when I put it inside.
Frustrating as this may be, I believe I'm actually getting closer to a solution since my symptoms now appear to be closely aligned with people having SATA ribbon cable issues.
Onward! -
G4 that will not boot from any disc EXCEPT the Apple Hardware Test CD
We have a DP 1ghz Quicksilver PowerMac G4 that will not boot from any disc EXCEPT the Apple Hardware Test CD that came with the machine.
We were in the process of installing 10.4 Tiger before placing it for sale.
The Mac was originally OSX Server 10.1 that we later converted to a worksation running 10.3 Panther.
It has 1 GB of memory, 80GB hardrive, 250MB Zip Drive and a Radeon 7500 video card.
Since this machine only has a CD-R drive and not a DVD-R, we installed Tiger using another Mac via Target Disk Mode. The installation process went well, but when I tried to reboot I got a Kernel Panic right after startup screen with the grey Apple logo.
On some reboots we get to the blue startup screen, others it stops at the grey Apple logo, others a black box like the a Kernel Panic - but with no text. Twice it went directly into Open Firmware.
We have done the following during our troubleshooting:
- Reseat RAM, Video Card, Hard Drive, Zip & CD-R connections
- Remove RAM 1 stick at a time and reboot
- Replace RAM with RAM from another working Quicksilver
- Replace Video Card with one from another working Quicksilver
- Zap PRAM
- Reset CUDA switch
- Unplug the MAC and remove everything (RAM, Battery, etc) for 30 minutes and try to reboot
- Tried booting from the Macintosh Server G4 Software Restore CD
- Tried booting from Mac OS X Server CD
- Tried booting from AppleCare Protection Plan CD with TechTool
- Tried booting from Diskwarrior CD
- Tried booting from an external FireWire drive with a disk image of Tiger OS Install
- Tried booting with the hard drive disconnected
The Mac WILL boot from the Apple Hardware Test CD and will pass ALL of the extended tests.Conventional wisdom says that any Mac that will not boot up from a System/Install CD OS 9 or an Install CD Mac OS X, has a Hardware problem.
The diagnostic CD is a red herring because it uses a very primitive method of reading the CD, and so does not properly represent the machines general ability to read CDs.
I would look at the CD drive cables, etc, and see if another drive gives different results.
You have not mentioned using the Startup Manager (option key at Startup) to do any checking:
HT1310- Startup Manager: How to select a startup volume -
Power Mac G4 400 MHz (AGP graphics) will not boot from hard drive
I have a Mac G4 400 MHz (AGP graphics) Machine Model: PowerMac 3.1 CPU Type:PowerPC G4 (2.8)
When I try to boot from the hard drive I get the folder with the flashing question Mark. The Machine will start up from the OSX 10.4 installer disk.
The system was running OSX 10.4.9 fine. I began to have problems with the hard drive, so I replaced it with an old Maxtor 5T040H4 40Gig Apple branded drive that I had sitting around.
The drive is jumpered (r50) for Master/Single.
I erased the drive in the old G4 using disk utility and wrote all zeros. I then used my store bought Tiger 10.4 install disk to install 10.4 on the drive.
After restarting I still get the flashing question mark. If I leave the Install disk in the DVD drive the system will attempt to install again.
I have zapped the PRAM, pressed the CUDA button, removed the battery and let the system sit unplugged for over and hour and it still will not boot from the hard drive.
To test the drive I removed it and put it in a Granite Digital firewire enclosure and connected it to another mac. The drive shows up and the system appears to be installed correctly.
What am I forgetting to do? Does anyone have any suggestions.
Thanks in advance.
Wesley G.Hi! If Tom's solution doesn't work I would reboot from the install disc and then partition the drive as 1 partition instead of erasing it. Sounds like the driver on the disk is too old and installing a new partition map should write a new driver to the drive that is compatible with Tiger. Other than that it is possible that the drive has a spin delay jumper enabled and the drive isn't spinning up fast enough and the computer isn't looking long enough for the drive. Tom
-
After 10.5 upgrade Mac will not boot from hard drive
I just upgraded to 10.5 Leopard but my mac will not boot from the hard drive even after selecting my hard drive as the startup disk. The mac will start to boot but will cut itself off before the boot is complete. I have to leave the Leopard disk in the mac and hold down C to get the mac to turn on but it only allows me to install the software again.
instead of archive and install you might first want to try restoring your system using TM to some time point before your failed 10.5.1 upgrade. Then try upgrading to 10.5.1 again. I would suggest downloading the full 110 MB upgrade and installing it manually rather than doing it through the software upgrade menu.
You can download the upgrade here:
http://www.apple.com/downloads/macosx/apple/macosx_updates/macosx1051update.html -
I'm trying to upgrade to SL from Tiger but the system will not boot from the CD. It reconizes the cd And launchs giving the install option. When install is selected I get a screen with only a restart option. After restart it comes back to the original install screen. Ran disk verify which found an issue. Put the original Tiger DVD in to try to repair and I get the same thing.I have tried the following.
1) Added a new external DVD drive as I thought it could be a hardware issue with the internal drive.
2) Restart holding "c". System simply boots from the hard drive.
3) Reboot holding option key. I receive the hard drive or cd choice. select CD. It boots as normal off the hard drive.
4) Selected Boot from CD in the system utilities start menu. System still boots from the hard drive.
5) Unplugged system for a few minutes. Same thing will only boot from hard drive.
6) reboot holding command, option, P, and R keys to reset. Same thing.
7) Unplugged all peripherals, except external DVD. Same thing boots as normal from the hard drive.
Currently running 10.4.1
Note when look for updates is selected the system always says none available. Other software updates fail.
Any ideas would be appreciated."A Mac that connot boot from an appropriate Installer/Utilities CD/DVD has a Hardware problem."
As a desperation move, you could try pulling your Hard Drive (with power OFF) to see whether you can boot from the DVD alone. It should still boot even if, when it gets there, there will be nothing to Install on.
EDIT: The theory you are testing is whether something on the Hard Drive is interfering with booting up in general. -
Flat Screen imac iMac won't boot up, will not boot from DVD
My 24" imac flat screen will not boot. I only get a blank gray/white screen. Reset the PRAM and tried to boot from the DVD. I held the C key down when I powered on but the system will not boot from the DVD. If I wait long enough, the DVD will eventually be ejected. I have had HD issues and Disk Warrior indicated that the drive was damaged. Will a dead hard drive cause the system to not boot from the DVD? Is there any way to get the system to boot from my DVD?
Hello PMcDer,
Welcome to Apple Discussions!
By what you are describing you're correct in believing your drive is probably gone. The sad news... if Disk utility can no longer see the drive, your ability to retrieve any data off of it is getting slim.
There are a couple of options for data retrieval.
1. If you still have Apple Care have them fix it. But make sure they know that you do not have a backup.
2. If you do not have Apple Care, have an Authorized Apple Tech replace the drive and make sure that they will give you back the old drive. This may prove to be a challenge. Or you can replace the drive yourself. It is not easy for some but take your time and you'll have no problems. Lots of youtube videos on this as well as on-line tutorials.
3. You could try a Hard Disk Utility program like Disk Warrior to see if it can help, but it's not free.
4. You could pay someone big bucks for Data recovery in order to get the data of the drive for you.
If you decided to do the HDD swap yourself. You could purchase a 3.5" firewire enclosure that you could put your old drive into once you do the swap. Plug it into the iMac and prey that it recognizes it. Then "MAYBE" you could copy the data over to the new drive, but that is a stretch.
Maybe you are looking for
-
My macbook pro keeps disconnecting from my airport
Hello Guys. So I am from Europe..Last summer i bought from America a Macbook Pro 13 mid 2014 and an Iphone 6. Two weeks ago i updated my products so i bought an Airport Express...(2)Everything was great(3) for one week...I was very happy(4) with my i
-
How to transfer inventory goods to asset
Hi, Certain items of capital goods have been posted to inventory at time of goods receipt. The same have to be transferred to asset code. How can I transfer these inventory goods into asset in the system? Rgds, GAG
-
Hi We have built an Adobe AIR application, where I've defined a video player in the mxml part. Now in the actionscript I'm looping over a playlist in XML where I'm updating the source of the video player everytime the playlist starts the loop. Now wh
-
JFileChooser, multiple dialogs.
My JFileChooser is getting the path and filename for a file, to be later opened. I'm placing the path and name in a JTextField. My problem is this: whenever I click 'Find' and select my file and click 'Open', the path and filename show in the JTextFi
-
How can you upload photos from iPhoto to FaceBook without having the sync where if you delete from iPhoto you delete