G56-125NR REBOOT ISSUE

I recently swtiched out my hard drive in my HP G56-125NR LAPTOP. I also purchased the HP reboot kit, as I did not have backup disks. When I use the Reboot disks, everything goes fine, it loads both disks plus third disk thats included. The issue is once Windows starts to load software, my laptop seems to freeze with the restart message on the screem (message box: restart now, restart later). The thing is, i cannot click with the mouse or simply hit enter to proceed. So my question is. should i wait, and it will restart on its own? or is there some combination of buttons I can hit to make it restart? any assistance is appreciated.
Thanks

OK. It would have been nice if you had shared that important tidbit of information with me.
After you replace the hard disk and install it to the same SATA port it was connected to, do you connect power, press the power button and then immediately tap the Esc key to enter the startup menu?
While in the startup menu put the first recovery disk in the DVD drive.
In the startup menu you have to select F9 and in the following menu choose the DVD drive as the boot item. After this. the DVD should boot into the recovery manager. Now you should just have to choose the type of recovery you prefer recovery and follow the prompts to reinstall the operating system.
The differences between System Recovery, Factory Reset and Minimized Image Recovery
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Similar Messages

I updated my Iphone 4s to IOS 7, now it reboots after every 2 minutes, I tried to restore, but the reboot gets it disconnected from PC, help me solve this reboot issue..

I updated my Iphone 4s to IOS 7, now it reboots after every 2 minutes, I tried to restore, but the reboot gets it disconnected from PC, help me solve this reboot issue..

See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once...
Be sure to Follow ALL the Steps...
But... if the Device has been Modified... this will Not necessarily work.

Firefox 3.6.23 having freezing and rebooting issues with Adobe Flash Player 11 Plugin

Firefox 3.6.23 is experiencing constant freezing and rebooting issues with Adobe Flash Player 11 Plugin, not sure if it is a conflict issue or not.
Since the update there had been no reported issues till today when the blue screen came up on me, this issue prior to plug in 11 had occurred at least 6 times, this issue only happens on firefox.
I do not wish to update since recent firefox browsers seem to have a lot of ongoing issues.

Anyone able to help please?
Thanks.

G56-125NR, short DST:Failed, Failure ID: 6CRK9D-5B75NB-XD003F-60W803

The computer doesnt load, Freeze at the windows 7 load screen, and loads to infinity. Ran the startup test and recived a short DST Faliure, The info is for a G56-125NR, other relivent information, short DST:Failed, Failure ID: 6CRK9D-5B75NB-XD003F-60W803

wow, I can see why you guys were rated #1 for support, business week 2009, I mean this is just stunning. I guess im off to find my own solution to the problem, would have help though if there was some sort of manual with the code names in them.If your #1 customer support isnt able to help. anyway i off bye.

MSI 970A-G45 reboot issues

Just did an upgrade to my PC.
Running the following:
MSI 970A-G45
Athlon Phenom X4 955 at Stock speeds(used from previous rig)
Corsair Vengeance 8GB PC12800 DDR3 1600MHz at Stock speeds(new)
XFX Radeon HD 6870 1GB GDDR5(new)
OCZ 120GB SOLID 3 SERIES SATA III 2.5 Hard Drive
Sony DVDRW 24x(used from previous rig)
BFG 550W PSU(used from previous rig)
Windows 7 64bit Ultimate
Here's the issue. Sometimes when I restart the PC, it never comes back up. It goes down like normal, then I have no video signal and it just sits there. It's doesn't happen all the time though, which is perplexing. When it does not come back up, I can simply hit the reset button and then it starts to boot up. Apparently it has all the latest BIOS and drivers according to MSI Live update. So at this point I have no idea what to try in order to get this thing to restart normally every time. I guess I shouldn't be too concerned considering I don't reboot a lot...?...?
P.S. I am not overclocking anything. Processor and RAM are running at stock speeds.
P.S.S. I do have two USB hard drives hooked up. Could one or both of them be causing the random reboot issue?
P.S.S.S. Although I mentioned the USB drives, I never had this reboot issue prior to upgrading to this motherboard, video card and ram.
THANKS!

Hello,
Having the same issue with similar hardware. PC will boot cold and shutdown like it should but restarting most of the time causes the system to hang with no video but the fans run and MB LED's are still lit. Pressing the reset causes the video to restore and POST and a normal boot. I tried an old video card to eliminate a video card problem but it does the same thing. Here is the hardware I'm running, I just built it today.
MSI 970A-G45
AMD Phenom II x4 955 BE (not OC)
MSI AMD Radeon 6770 1GB DDR5 (Not OC)
Kingston HyperX Blue 4GB DDR3 PN:KHX1333C9D3B1/4G
LiteON 24x DVDRW (SATA)
WD Caviar Blue 6.0GB/S 250GB HDD
Cooler Master Extreme Power plus 500W PSU
I would post CPU-Z stats but I cant figure out how to attach images. help?
Areamike,
To adjust the command rate you have to go into the overclock tab and go into advanced DRAM config. If I can remember right you may have to adjust another setting away from AUTO to be able to access this menu. (i would be able to tell you for sure but I cant look at BIOS and be on the forum typing at the same time.lol) After having this problem I read a lot of reviews with people having trouble with this board, hopefully its just a setup problem for us.
-RickyB

G56-125nr notebook pc - max supported HD

as it says
what is the maximum supported HD on a g56-125nr on Win 7 - home prem. 64-bit ?
thanks

i meant HD as in hard drive size max hard drive size that the mobo, or OS, can support i'm trying to put a 1TB hdd in it.

Freezing and Rebooting issue - Hardware or Softwar...

Sorry if this has been asked before...but...
Is the freezing and rebooting issue caused by a fault in the Hardware or Software...?
Can someone from BT please explain just exactly what is going on.
Thank you,
wdp

sarahoxford wrote:
Just been on live chat as we are fed up of freezing up, random reboots and failed recordings. Usually happens on Gold, Sky Sports - the non freeview channels. Advice from Geetesh was factory reset thus losing existing recordings, stating rather optimistically that this 'will resolve the problem'. When pushed on freezing and failed recordings issue Geetesh said recording of 'internet channels is in a test phase so won't be able to record'?? But we have recorded on gold, fox for example - response is that it won't always work, only for some customers.
The advisor was getting confused. The bit about recording broadband channels still being in test phase only applies to BT Youview boxes. The recording functionality has been available for broadband channels on the BT Vision+ boxes since they launched last January.
To answer the original question. The occasional freezes and reboots are caused by the New Look software (possibly in conjunction with associated system changes on the BT servers). Many of us had years of trouble free viewing using the Classic software on the same black BT Vision+ boxes. It was only when we were upgraded to the New Look software that all the troubles began. If however, you are getting such problems many times per day, or even many times per hour that could indicate a hardware fault.

MSI X79A GD-45 - Random Locking / Rebooting Issues

Hi,
I recently upgraded my old P45 chipset Q6600 16GB Hyper-V home lab server, with a nice X79A GD-45 Board, with an i3820 & 64GB of Ram.
I've installed the system with Windows 2012, however I can't seem to get it stable.
I have a basic AMD 4550 graphics card in the server, and Dual Port HP360T nic, 2 x LSI Raid Controllers, I have tried removing all of this, but still get the same issues.
I have the latest BIOS updates from the MSI website.
I found that switching the ACPI power settings to C6 in the BIOS improved the stability but it hasn't resolved the problem completely.
I have my memory running @ 1333Mhz, as I've seen some people mention that trying to run 8x8GB @ 1600Mhz can cause problems, but that makes no difference.
I've tried running with 32GB of Ram rather than 64GB but same issues.
The strange thing is the PC doesn't blue screen, it sort of hangs, i.e. Windows 2012 goes un responsive, however I can still move the mouse cursor around, just nothing works, other times it just reboot's itself, and I get unexpected shutdown messages in the event logs.
Do I have a dogdy m/board, or is there some other secret to getting the X79 boards stable, my old Q6600 on intel P45 chipset was like a rock, longest uptime was over 250 days without a reboot..
Thanks,
Andy.

Hi,
Just to let you all know that i think I had two issues in the end, the MSI commander software causing random reboots of Windows 2012, and also an old casecom 500w PSU that was causing the strange partial hangs.
Removing MSI commander software and setting FAN control directly in BIOS stopped the random reboots, however I was still getting problems with partial crashes for example Hyper-V VM's still running but windows desktop would go unresponsive etc.. and also issues with occasional HD corruption.
Since replacing the PSU the partial lockups / crashing have gone away, and I've had no more instances of corruption, server stable now for 80hrs+ without a reboot or weird partial hang :-)
In addition moving to a new 80+ platinum PSU has seen the power draw to run the system drop from 38-40% of the capacity of my UPS down to 17-18% so I've halved the amount of electricity that my server uses when on 24/7, from about 200-250w down to less than 100w, just the saving of approx 2.4Kwh a day (equates to about £0.30 a day) so across the year the PSU will have paid for itself !

IPhone lock-up, crash & rebooting issues?

Hi, All – I have the original iPhone with 2.0 software. Since the initial install and even after doing a restore on it, the phone has been crashing and rebooting intermittently. I am using AT&T service, and I have never attempted to unlock the phone or run arbitrary code on it, so these issues are baffling to me. Below is a brief list of what I’ve encountered. Again, the iPhone is crashing and rebooting, not the apps:
Press the “Home” button = intermittent crash, then reboot (might happen back to back, or as infrequently as 6 hours – no rhyme or reason)
Press the “Power” button = (same result as above)
Phone locked up when receiving a call, lit up & identified the caller, no ring or vibration then it rebooted. This has happened twice.
Phone locked up when receiving a text message. Noticed it as I heard an odd tone from my phone for a split second, then it crashed and rebooted and showed a text message on the home screen when it finished rebooting.
Also, I have had other problems where the phone didn’t crash or reboot – it just didn’t perform properly:
When receiving a call – display does not light; phone does not ring or buzz. Voicemail received from caller though call not noted in received calls list. Also, I have had a greater number of “Call Failed” problems, even with full cell signal in Denver, CO. This may be AT&T’s fault, but it seems fine after I shut down and restart the phone.
In general, my iPhone with 2.0 software seems a bit more laggy. Screen rotation from portrait to landscape isn’t as smooth and opening the SMS app seems to have a consistent 2-second delay regardless of if I have cleared out my text message logs or not.
Also, when I reboot the phone, more often than not it starts off at the “slide to unlock” screen instead of the home screen.
Regarding location services – My gripe is that it can’t be told to either:
Stay on all the time
Shut off all the time
Activate when needed, then shut off – just like in 1.1.4.
Now when I use an application that I allow to use location services, I have to manually go and shut location services off again or my battery life will suffer.
I have now removed all of the new applications from the phone, and am still experiencing crash/reboot problems. My guess is my phone is damaged somehow or the software I downloaded was somehow flawed during downloading or installation.
Does anyone have any ideas? I really like this phone, but I can't bring myself to buy the new 3G if I can't be certain I wouldn't have the same problems
Thank you,
Lynn

I have experienced this problem as well and it is intermittent to say the least. I have two other friends that have an i-phone as well, and when the phone crashed it stored a picture of the screen in the photo library of the phone. I thought that was a little odd as well. I have another friend that has not updated to 2.0 yet and does not seem to be having any problems at all. I would venture to guess that there is a problem with the update and that an update will be out sometime to correct the problem. If anyone knows of a way to correct the problem please post a fix for us.

IPhone 5 Battery Indicator and Reboot issues

Hello Apple community forum,
I have an iPhone 5 that I purchased approximately 20 months ago. It has worked flawlessly and been well taken care of. Only until recently, maybe 3 weeks after I updated to IOS update 7.1.1, I have been having a plethora of issues and now the phone is virtual useless. I have not jailbroken it or have had any third party hardware installed. It all started when I plugged in my Apple lightening cable for charging and an error appeared "unsupported charging cable". From there I have experienced the following problems:
Battery indicator stuck while charging at any various percentage or during normal use and standby. Only a reboot will provide current charge status.
Extremely fast battery drain.
Unexpected reboots at various intervals or while accessing Apps or browsers. Sometimes very frequent. One day had at least 60 reboots. one right after the other.
Cannot turn on or off
Shuts off when I put it in my pocket.
BSOD (Blue Screen of Death)
Screen exhibits lines or odd characters shuts down or reboots.
Time and date at different positions post boot.
Log file full of errors. (Panaic.ips bug type 110 | awdd Wireless | ResetCounter bug type 115| TCCService bug type 167 | Log-Aggregated bug type 193)
The update worked great on the phone and it seemed faster and the battery lasted a bit longer than usual.However, now it is a different story. I was able to backup my phone and offload all my photos on its good day. I was reading the support site and following a few of these forums. I follow the soft and hard rest procedures and even restored the phone back to factory default (DFU mode). It does seem to run a bit better in default without many apps on it but it still exhibits all the above issues. I bit the bullet and went to the Apple store to talk to one of there G men. He acted surprised and gave me the Apple trained verbal run around. He ran the diagnostic and stated that my battery did not even register as being in the system. From there he opened the phone, inspected it for damage and re-attached the battery and taped it back down. BTW, they hosed my screen cover. Nothing is ever free. They did offer to replace my battery for $80 but did not feel that would solve this problem. If anyone has had this issue and did have a new battery installed, please let me know how that worked out.
I wonder if this latest update exposes some type of hardware flaw that was previously fixed or just a bug(s) in the software code. Yet, Apple does not seem to acknowledge there is a problem let alone advise to any upcoming fix. It does not seem that Apple really cares about my little bit of business. If anyone has any ideas or experience, please let me know. This is frustrating and owning too much of my time. Thanks Apple!

If tried techniques to get the battery to act right, such as rebooting by holding both the power and home buttons until the apple logo appears and it restarts, and those things haven't helped, take the iPhone and iPad to the Apple store genius bar and have the technicians test them to see if there is a hardware fault. Do that before the warranty runs out so you are covered.

Macbook pro Retina 15" reboot issues

Hi all
I am a newcomer to the community.
Right I've had the my brand new macbook pro retina 15' since the begining of september 2014 which came with Mavericks.All seems fine back then
I did the terrible thing and upgraded to the yosmite when it came out and I've starting to have issues , with the wifi dropage etc etc
My most recently issue which has come to light is that , after I've RESTORED Yosemite many times (yesterday was the last time) when ever i use the computer and then reboot after few minutes to some time the computer takes super long and hangs at rebooting???????
I get a that "progress spinning chopped up circle thing" staright after i reboot and sometimes it just hangs there with the Fans going full blast till i need to hold the power button down! like what the ****
does anyone have this issue? or know how to resolve this? or do i need to bring it back to apple?
My macbook is top spec 15 inch Mid 2014 one with only the minus of the 1tb hard drive upgrade , however i feel its should not be having these problem.
I must admit since i have the macbook pro , I've used Parallels a lot , bootcamp and FileVault encrypting (which is now turned off) testing things out. i thought as this is a top spec it should handle this no problems as i got this for a development machine. Ever since Ive got Yosemite its like its slowed down and become sluggish.
When I had maverick i did not experience a ton of problems like Yosemite, it booted up in 8 secs and shutdown immediately althought i did not test the file vault encrypting under mavericks.
Also sometimes when my Fans will be on full blast when i am not doing anything intensive, like when i browse with chrome or finished with parallel.
I be grateful if anyone can help me solve this since its now not a issue of restoring which I've done many times. I dunno if I've pushed the SSD to to much or something......
Is there a way to revert had to mavericks? without a usb or cd
Thanks
Zyco

Before trying to go back to Mavericks, try performing an SMC and NVRAM/PRAM reset. These two components control several functions of your MacBook Pro and by resetting them to their default values it may clear up the issue that you're seeing.
To reset the SMC:
Turn off your computer and ensure the MagSafe adapter is plugged in.
Hold down Shift-Control-Option on the left side of your keyboard, and then hold down the Power button at the same time.
Wait about 5 seconds, and then release the keys. You may see the light on the power adapter change colour momentarily.
Don't turn the computer on just yet, we'll do that in the next step.
To reset the NVRAM/PRAM:
Press the Power button and then immediately hold down Command-Option-P-R on your keyboard at the same time.
Continue holding these keys until your MacBook Pro restarts and you hear the start up chime a second time.
Release the keys and continue booting into OS X.
If this doesn't work, try booting into Safe Mode. This will help you determine whether a software issue is causing your problem. To boot your Mac into Safe Mode, restart the computer and hold down the Shift key until you see the Apple logo appear on the screen. It may take a little while longer to boot up as OS X will verify the state of your disk and clear out certain caches and temporary files. Once booted into Safe Mode, try restarting and see if the issue persists.

AP reboot issue w/ WLC4400 and LAP1020

Hello,
I have a WiFi network based on WLC4400 (SW version 4.2.130.0) and 14 LAP1040s (SW ver. 4.2.130.0, boot ver. 2.1.78.0).
I'm experimenting AP reboots with no apparent reason (no evident correlated event which triggers the reboot).
From WLC4400 log I see messages like the following when reboots happen:
Jun 14 09:21:08.931 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:2e:30 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 09:20:57.478 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:77:d0 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 09:20:38.709 spam_apf.c:314 LWAPP-3-AP_DB_ERR1: Unable to find AP 00:0b:85:9a:77:d0 entry in the database, could not process delete WLAN ALL MNs message
Jun 14 09:20:38.708 spam_l2.c:760 LWAPP-3-TX_ERR3: Max retransmissions for LWAPP control message reached on AP 00:0b:85:9a:77:d0 for CONFIGURE_COMMAND (number of pending messages is 1)
Jun 14 09:19:54.694 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:9a:77:d0
Jun 14 09:19:54.109 spam_l2.c:387 LWAPP-3-RX_ERR: Received an unexpected LWAPP packet from AP 00:0b:85:9a:77:d0
Jun 14 09:15:35.261 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:2e:30 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 09:15:23.806 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:77:d0 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 09:15:02.698 spam_l2.c:760 LWAPP-3-TX_ERR3: Max retransmissions for LWAPP control message reached on AP 00:0b:85:9a:77:d0 for CONFIGURE_COMMAND (number of pending messages is 2)
Jun 14 09:10:00.735 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:2e:30 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 09:09:50.089 spam_l2.c:404 LWAPP-3-RX_ERR3: Received LWAPP packet with invalid sequence number (got 1expected 2) - from AP 00:0b:85:9a:77:d0
Jun 14 09:09:50.089 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:77:d0 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 09:09:48.369 spam_apf.c:314 LWAPP-3-AP_DB_ERR1: Unable to find AP 00:0b:85:9a:2e:30 entry in the database, could not process delete WLAN ALL MNs message
Jun 14 09:09:48.367 spam_l2.c:760 LWAPP-3-TX_ERR3: Max retransmissions for LWAPP control message reached on AP 00:0b:85:9a:2e:30 for CONFIGURE_COMMAND (number of pending messages is 1)
Jun 14 09:04:25.557 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:80:a3:c0 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     RRM_DATA_REQ)
Jun 14 09:04:25.414 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:80:a0:10 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 09:04:24.039 apf_rogue.c:736 APF-1-UNABLE_TO_KEEP_ROUGE_CONTAIN: Unable to keep rogue f4:ec:38:cd:a1:9e in contained state - no available AP to contain.
Jun 14 09:04:16.528 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:77:d0 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 09:04:15.011 apf_rogue.c:736 APF-1-UNABLE_TO_KEEP_ROUGE_CONTAIN: Unable to keep rogue 54:e6:fc:e6:a2:3c in contained state - no available AP to contain.
Jun 14 09:04:03.634 spam_apf.c:314 LWAPP-3-AP_DB_ERR1: Unable to find AP 00:0b:85:80:a3:c0 entry in the database, could not process delete WLAN ALL MNs message
Jun 14 09:04:03.632 spam_l2.c:760 LWAPP-3-TX_ERR3: Max retransmissions for LWAPP control message reached on AP 00:0b:85:80:a3:c0 for CONFIGURE_COMMAND
(number of pending messages is 1)
Previous message occurred 2 times.
Jun 14 09:03:56.221 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:80:a3:c0
Jun 14 09:03:55.160 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:80:a3:c0
Jun 14 09:03:55.159 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:80:a3:c0
Previous message occurred 2 times.
Jun 14 09:03:54.174 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:80:a3:c0
Jun 14 09:03:53.151 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:80:a3:c0
Jun 14 09:03:53.150 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:80:a3:c0
Previous message occurred 2 times.
Jun 14 09:03:52.093 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:80:a3:c0
Jun 14 09:03:51.094 spam_lrad.c:2630 LWAPP-3-RX_ERR9: Received a bad sequenced RRM data request message from AP 00:0b:85:80:a3:c0
Jun 14 08:58:41.884 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:77:d0 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 08:58:23.832 spam_l2.c:760 LWAPP-3-TX_ERR3: Max retransmissions for LWAPP control message reached on AP 00:0b:85:9a:77:d0 for CONFIGURE_COMMAND (number of pending messages is 1)
Jun 14 08:58:03.541 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:81:00 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     ECHO_REQUEST)
Jun 14 08:57:57.390 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:9a:2e:30 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     RRM_DATA_REQ)
Jun 14 08:57:56.460 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:80:a3:c0 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     RRM_DATA_REQ)
Jun 14 08:57:51.925 spam_lrad.c:2286 LWAPP-3-REBOOT_ERR2: AP 00:0b:85:80:a0:10 joined to the controller currently experienced a reboot earlier - (Link Failure Reason:     RRM_DATA_REQ)
Just before the AP reboots, a wifi client connected to that AP looses wifi connection for about 20 secs (wifi connection is ok, just no IP traffic can go through).
Can anybody help me on troubleshooting the issue?
Thanks,
Marco

I dont think it s DHCP issue, as there are no DHCP conflcts coming up.
This issue looks to be something related with the power negotiation with the AP and the switch
I did a tdr testing and the AP came up and again after a while it went down.. and the tdr testing was showing as incompleted
ATTW.IDFL15#show cable-diagnostics tdr interface gi 3/0/44
TDR test last run on: February 23 11:44:39
Interface Speed Local pair Pair length        Remote pair Pair status
Gi3/0/44 100M Pair A     N/A                N/A         Not Completed
                Pair B     N/A                N/A         Not Completed
                Pair C     N/A                N/A         Not Completed
                Pair D     N/A                N/A         Not Completed
But I can see the Speed negiotiation done to 100M, but actually it should be 1000M.
The AP fell back to this state after TDR testing
Gi3/0/44 auto   on         15.4    Ieee PD             3     30.0
This AP was not joining the WLC and i had to console, it joined the WLC once when I plugged out the cable and plugged in. But lost the connectivity soon and I had to boot with the rcv image for the AP join the WLC
Thanks
NikhiL

FSCK and reboot issues with external USB drive

I'm having an issue with an external USB hard drive I'm using. I've always had issues with this drive cause my reboot to "freeze" when it's mounted. Basically the system message with be sent out, but it doesn't actually proceed with the reboot. No switch to init 6 or anything, but the shutdown process is still active. I can continue to use the computer as usual, but I can't cancel the existing shutdown or try to enter init level 6 by hand. So I just got around this by unmounting the drive before I shutdown. However, lately when I try to unmount the drive I get an error saying that the drive is in use and I should check to see what processes are using it by runing lsof or fuser.
Yesterday I tried copying dsome files from the drive but there wasn't and activity on the drive. cp didn't report any errors though, it just sat there and did nothing. I tried running fsck on the drive, but didn't get much farther. I'll see some activity on the drive for about a second, then all activity stops and fsck just sits there. When I try to kill fsck, it won't. Even with a kill -9.
I'm really confused as to what is going on. Has anyone else had this problem? Anyone have any ideas what could be causing all this or what I can do to stop this? Thanks in advance!
David
[email protected]

Press the reset button on the device. It is located between the USB and power ports. Make sure to take-out the external USB drive before you reset the device. Or you can also restore the defaults by accessing the Administration tab > Factory Defaults sub-tab in the router’s web-based setup page. Check out this link for the set up; http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=32cffead811249aea7e9fc6730bf59ad_KB25681_EN_v1.xml...

KT6 Delta Rebooting Issues - Solution that Worked for me

Hi
Solution that worked for me: Enabled SATA Controller which takes a while for it to detect SATA Drive and giving time for the system to warm up. I don't get that annoying message asking to restart Windows in safe mode, normal, & etc.
I've been having this rebooting problem lately. I tried everything from BIOS settings, checking drivers for problems, checking Windows XP, Power Supply, Checking Motherboard,and etc. I installed a fresh copy of Windows but still had that rebooting problem. When I got this MB 3 months ago, it was working perfectly and had no rebooting problmes. But its now fall in my place and the temp a bit cold.
I read about the temperature issue (20C). I disbaled the SATA controller because i don't have a SATA Drive.
Hope this will help others as well and for MSI to Fix the Problem.
Barton 2500+
Ati Radeon 9000 Pro
Maxtor DiamondPlus9 80 gig
Western Digital WBC 120 gig
LiteON 52x24x52
360W PS

No, i`m sure that trick it`s not working for me and for rest of us.
I did try all trick in the bios, and...

Strange Server 2012R2 Networking Disconnect On Reboot Issue

Strange issue. Server 2012R2, Dell R710, Broadcom BCM5709C eth adapters. 2 of the adapters are on a LAG for hyper-v. 1 is not connected, 1 is connected for management.
Every time the server reboots, the management interface does not connect. The only fix is to connect via the DRAC, disable the not-connected adapter, then enable the not-connected adapter and then it properly connects to the network. Prior to that it shows up as "unidentified network"
This topic first appeared in the Spiceworks Community

Strange issue. Server 2012R2, Dell R710, Broadcom BCM5709C eth adapters. 2 of the adapters are on a LAG for hyper-v. 1 is not connected, 1 is connected for management.
Every time the server reboots, the management interface does not connect. The only fix is to connect via the DRAC, disable the not-connected adapter, then enable the not-connected adapter and then it properly connects to the network. Prior to that it shows up as "unidentified network"
This topic first appeared in the Spiceworks Community

G56-125NR REBOOT ISSUE

Similar Messages

Maybe you are looking for