G570 amd driver

There is a new amd graphics but my laptop was bought two years ago and it released in 2013.Will it work on my pc?
Solved!
Go to Solution.

Hi Chiku,
Welcome to Lenovo Community Forums!
To check if the driver is compatible with the AMD Graphics hardware in your G570 Laptop, below is the link to automatically scan the computer and install the relevant driver for the computer:
AMD Driver Autodetect
Hope this helps!!!
Do post us back for further queries.
Best Regards
Shiva Kumar
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Similar Messages

  • Can't install AMD driver properly lost all CCC options and 3D

    Hi everyone,
    I have HP pavilion g6 , win 7 64 bit. Amd Radeon HD 7400M series and Intel HD graphics.
    My problem started when my screen was getting  black for seconds  alot and when it comes back it said amd stopped so I decided to update the driver. 
    First I downloaded the supported driver from the site 
    http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-98607-2&cc=emea_middle_east...
    but every time I try installing it the install process run very quickly the screen doesn't even switch during installtion and it says driver is successfully installed although nothing was installed and nothing absolutely change.
    so I decided to download the latest amd driver from amd site14.4. I had some problems while installing but it worked fine and  I had all the options including the switchable graphics. But after a while the laptop started to hang on startup showing a blue screen saying something was incompatible.
    So I tried to update the driver from device manager and since then I lost all catalyst control center options also the switchable graphics mode and 3D in photoshop isn't working anymore and every time I close the catalyst a message come saying it stopped working. I tried many times to uninstall the driver then installing a new versin 14.9, the prvious 14.4, the supported but still nothing of them worked at all, also I tried installing with win 7 compatibility but it always gets stuck. Sorry for elongation but I'm so tired of this problem. I really appreciate any help.
    This question was solved.
    View Solution.

    Hi @Black_violet ,
    Thank you for visiting the HP Support Forums and Welcome. I have looked into your issue HP Pavilion g6-1045sx Notebook and issues with graphic software. Here is the drivers for your device. I would uninstall both and restart the computer, then reinstall only the AMD. It will include the Amd Graphics Driver and Catalyst Control Center restart the computer.
    The Intel will automatically install.
    Here is a link to the HP Support Assistant. Just download and run the application and it will help with the software and drivers on your system.
    You can do a system restore. System restore will help if something automatically updated and did not go well on the Notebook.
    When performing a System restore please note remove any and all USB devices. Disconnect all non-essential devices as they can cause issues.
    Please let me know how this goes.
    Thanks.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

  • Fail during installing AMD driver

    Hi , i have been trying to update my AMD 6770m driver from 8.830.6.1000 to the new update but i failed each time
    i tried auto detection and update and it shows me errors
    i tried manualy by browsing to the c/amd/support then the driver but it show that my driver is uptodate !!!
    one time it showed succes and told me to restart my computer then after i did it bring back the old !!
    i tried to uninstall it then restart but it goes back to the old
    my computer is HP pavilion dv6 6285ex

    Hello kreem,
    Welcome to the HP Forums!
    I understand the computer cannot install the latest AMD driver. I'll do my best to assist you! First, I require the following information:
    1. What are the exact errors that appear when you try to install the AMD driver?
    2. The computer's operating system. If you require assistance locating this information, please reference this website to determine your Windows operating system.
    3. Have you installed any new software or drivers on this computer, before the issue appeared?
    4. Are you trying to install the driver from HP.com or AMD.com?
    Thanks, and have a great day!
    Mario
    I worked on behalf of HP.

  • When using lighting effects in cc programme freezes and then window comes up sayind amd driver stopped working but is now ok. Tried to open lighting effects in cs6  and default spotlight is there but then it freezes. No mention of driver problems. Any  s6

    Problem with accessing lighting effects in cc and cs6. In cc programme freezes and then window appears saying amd driver stopped working but is now ok but cc still frozen. Tried opening in cs6 no problem with driver but just default spotlight appears and then programme freezes. Any suggestions.

    That is  very old for drivers and new driver for the chipset will not be coming I do not see it as supported either Photoshop CC and CC 2014 GPU FAQ
    Tested video cards for Photoshop CC and CC 2014
    Adobe tested the following video cards before the release of Photoshop CC and CC 2014. This document lists the video card by series. The minimum amount of VRAM supported on video cards for Photoshop CC and CC 2014 is 512 MB.
    Important: This document is updated as newly released cards are tested. However, Adobe cannot test all cards in a timely manner. If a video card is not listed here, but was released after May 2013, you can assume that the card will work with Photoshop CC and CC 2014.
    Adobe tested laptop and desktop versions of the following cards. Be sure to download the latest driver for your specific model (Laptop and desktop versions have slightly different names.)
    nVidia GeForce: 400, 500, 600, 700 series
    nVidia Quadro: 2000, 4000 (Windows and Mac OS), CX, 5000, 6000, K600, K2000, K4000, K5000 (Windows and Mac OS)
    nVidia GRID K1, K2
    AMD/ATI Radeon: 5000, 6000, 7000, R7, R9 series, 7950 Mac OS
    AMD/ATI FirePro: 3800, 4800, 5800, 7800, 8800, 9800, 3900, 4900, 5900, 7900, W8100, W9100, D300, D500, D700
    AMD/ATI FireGL: W5000, W7000, W8000
    Intel HD Graphics P3000, Intel HD Graphics P4000, Intel(R) HD Graphics P4600/P4700, Intel HD Graphics 5000
    Note: AMD/ATI 1000, 2000, 3000, 4000 series, nVidia GeForce 7000, 8000, 9000, 100, 200, 300 series and Intel HD Graphics (First generation) cards/GPUs are no longer being tested and are not officially supported in Photoshop CC and CC 2014. Some GL functionality is available for these cards, but it's possible that newer features don't work.

  • Uninstalling AMD driver

    Hi all,
    My Macbook Pro 17" (Early 2011) recently got the known issue with the AMD Radeon HD 6750M, weirds columns and lines on screen, to finally freeze for ever.
    Getting a replacement is not possible because the cost of motherboard is near the price of a new macbook Pro, but above all it has the same defective AMD card built in, so one can get the problem very soon again.
    Two friends of mine have had the same problem (yep, 2011 models, same graphic card), but one of them got luck with a reballing procedure, and it seems that the computer is working Ok for the moment. So I decided to do the same, and the computer is working better now, but sometimes this weird lines appear. The guy at the technical service told me that the amd processor is still working over its regular temperature, so I can expect its death.
    I would like to uninstall the AMD driver so I can use the Intel HD 3000 only. At least the computer could be used for email and surfing the web...
    I know that there is a little app, called gfx, that has the option to use one or the other, but if you need to reboot the mac, it loads the AMD driver again, and I'm afraid that I'll finally get the same problem, a point where the computer freezes and you are done.
    I was looking on the AMD site, but they seem to have uninstall solutions for Windows only.
    Any help appreciated.
    Best,
    Pablo

    Hi all,
    My Macbook Pro 17" (Early 2011) recently got the known issue with the AMD Radeon HD 6750M, weirds columns and lines on screen, to finally freeze for ever.
    Getting a replacement is not possible because the cost of motherboard is near the price of a new macbook Pro, but above all it has the same defective AMD card built in, so one can get the problem very soon again.
    Two friends of mine have had the same problem (yep, 2011 models, same graphic card), but one of them got luck with a reballing procedure, and it seems that the computer is working Ok for the moment. So I decided to do the same, and the computer is working better now, but sometimes this weird lines appear. The guy at the technical service told me that the amd processor is still working over its regular temperature, so I can expect its death.
    I would like to uninstall the AMD driver so I can use the Intel HD 3000 only. At least the computer could be used for email and surfing the web...
    I know that there is a little app, called gfx, that has the option to use one or the other, but if you need to reboot the mac, it loads the AMD driver again, and I'm afraid that I'll finally get the same problem, a point where the computer freezes and you are done.
    I was looking on the AMD site, but they seem to have uninstall solutions for Windows only.
    Any help appreciated.
    Best,
    Pablo

  • My AMD Driver crashes and recovers almost daily. Is there anyway to stop this?

    My laptop is a HP Pavillion g7-2224nr notebook and my driver is the default one, a AMD Radeon HD 7420G Discrete-Class Graphics. 
    It doesn't bluescreen, but when I'm watching youtube videos, the video will randomly stop and it'll say 'the amd driver has disconnected and successfully reconnected'.
    Do you guys have any suggestions to helping me?
    Edit: Forgot to add, it's a windows 8.1.
    This question was solved.
    View Solution.

    It worked great. I installed it and it hasn't crashed once. I was even able to play one of my favorite games.

  • Display driver stopped responding and has recovered. display driver amd driver s

    Hello
    I have a problem with my graphics card: R7850 twinforce. It was working very good.(i have windows 8, 64 bits)
    But now i get this error when i play a game(after 1 min already):
    Display driver stopped responding and has recovered. display driver amd driver stopped responding and has recovered.
    Who can help me please?
    Kind regard

    Quote
    PSU:   
      What psu?
    Quote
    MEM: 8,00GB Dual-Channel DDR3 @ 799MHz (11-11-11-28)
    Model? Specs? Matched kit?
    Quote
    OC
    ? Oc yes or no?

  • Hp pavillion all in one AMD driver installation

    I had to reset my operating system and I am now gettin a message indicating i need to install AMD driver graphics it is not completely installed or driver need to be installed

    I thought that when you put the DVD in the screen would bring up the movie to play ?

  • Amd drives not installing on my g6-2123

    pavilion g6-2123 us
    windows 7 64 bit

    Hi,
    What is the complete product name or product number for your notebook? What you have posted is only a partial one.
    Are you able to boot into Windows?
    There is a Recovery Manager available from within Windows that contains all of the applicable drivers for the installed operating system. Windows orb-->HP-->Recovery Manager.
    Choose the AMD driver from the available list and click on install. If your notebook has an AMD discrete module and an Intel HD onboard graphics chip the driver will install both.
    You can also install the drivers by using the recovery disk set or recovery media that you should have created when you first setup your notebook.
    Best regards,
    erico
    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • [pavilion g7-2116sr] How can I use amd driver with only integrated graphic?

     Radeon hd 7670m is disabled coz it's broken. Amd driver don't work. Windows use vgasave driver. How can i use amd driver with radeon hd7660g?
    P.S.  Sorry, my english isn't good(

    Hi @Leys 
    I see you are stilll unsuccessful installing the drivers as you get the blue screen.
    Here is a link to Computer Does not Start (Windows 7, Vista, XP) that may help.
    Here is a link to Testing for Hardware Failures (Windows 7, Vista) to determine if your graphic card is defective.
    If the graphic card fails, here is a link to the HP Pavilion g7 Notebook PC Maintenance and Service Guide. Please note page 9 or chapter 1 page 9 for a list of recommended replacement graphic cards.
    If the graphic card passes you may wish to consider doing a restore back to a known good time or a full recovery back to factory.
    Using Microsoft System Restore (Windows 7)
    Performing an HP system recovery (Windows 7)
    During the recovery process there is an option to backup your personal files to prevent data loss.  If you have not done one yet I suggest you do one now.
    Restoring Files that were Backed Up Using HP Recovery Manager (Windows 7)
    At any time you may wish to contact HP support for assistance.
    Please call our technical support at 800 474 6836. If you live outside the US/Canada Region, please click the link below to get a support number for your region.
    World Wide Phone Support
    Good Luck!
    Sparkles1
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

  • Amd driver not installing in any os

    hello everyone,
    about 6 months erlier my harddrive crashed so i changed it with a new 7200rpm version, after that my problems started. first i installed win 7 and tried my amd driver form hp website but it didnot work. whenever i start installation windows freezes and there is no other option for me other then swiching off my lappy by holding the powerbutten. i tried all short of software from amd and intel and i tried leshcatlabs drivers too but nothing worked. so i tried win 8 and 8.1 but the results are same. intel driver works perfectly so does all the other drivers exept the amd drive. 
    its extremely frustrating . if any1 else have faced the same issue or anyone have any solution please reply.

    What is the installed operating system in the notebook?
    How did you install the OS in the new hard disk?
    Did you verify that all required drivers are installed?
    Which CPU is installed in the notebook?
    Help us to help you by posting the following information.
    1.  The complete Model Name. or Product Number. of the notebook - see This HP web document if you don't how to locate the model number and\or product number.
    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • [HP IGNORANCE] 4x40s windows 8.1 AMD driver - UNSOLVED & IGNORED ISSUE (sleep = restart)

    HP STOP IGRNOING US AND SUPPORT YOUR PRODUCTS!!!
    WINDOWS 8.1 IS NOT A WHOLE DIFFERENT SYSTEM - IT IS AN UPDATE TO 8
    As all interested guys know, there is currently no proper driver for our AMD cards in 4x40s for AN UPDATE of a system - windows 8.1.
    This is seriously wrong - we all have issues: inability to put notebook to sleep due to broken AMD driver. Effect of trying putting computer to sleep is total restart on waking up.
    HP jest doesn't want to support laptop which still is on shelves and resellers are still selling them.
    Why you're not supporting 8.1 on this laptop??
    Topics covering issue:
    http://h30434.www3.hp.com/t5/Notebook-Display-and-Video/Probook-4740s-video-drivers-broken-sleep-res...
    http://h30434.www3.hp.com/t5/Notebook-Display-and-Video/Probook-4540s-with-Windows-8-1-64bit-can-t-i... - last pages

    So HP decides not to resolve the issue, but to close the topic?
    It's so ridiculous!!! Shame on you HP!
    As for today the status is that since the Windows 8.1 i released: September 2013, HP is not able to provide support for their product.
    I've just made up my mind and I am going to return this product to the seller I bought it from. Farewell HP.

  • K8N Neo2 wierd boot / AMD driver ?

    I just put this rig together and am still fiddling with things.  After playing with Corecenter and Speedfan and CnQ, and having Corecenter alarm continuously after installing Speedfan, uninstalling Corecenter, wondering if CnQ was working, etc., I ended up installing the AMD driver 1.2.2.2.  Things worked okay but when I reinstalled Corecenter it still alarmed continuously (I never could tell why or how to silence the alarm other than closing Corecenter).  I decided to uninstall the AMD driver to try to get back to my original configuration.  During the reboot after the uninstall the system acted a little funny.  Once in the Windows boot the screen went black and then back to the boot screen three times, and then went black and then back on while in the Windows screen before finally settling down.  CnQ would not work after this so I re-installed the AMD 1.2.2.2 driver.  Everything now works, but the weird boot up still happens with the screen going black several times in the process.  Also, when I go to Advanced settings in the Display Properties/Settings the computer seems to hang for several seconds, then the screen goes blank, comes back on and then displays the advanced screens.
    BTW, my goal is to have a QUIET computer that will still perform okay for the games my kids play on this machine.
    I have a couple of questions related to all this.
    1)  Is the weird boot up and blank screen when going to the Advanced Display Settings related?
    2) Can I uninstall the AMD driver and go back to the Windows driver (that did allow CnQ in the first place)?
    3)  Finally, I would prefer to ditch Corecenter and use Speedfan.  During all this at some point Speedfan displayed info on my video board (voltages, temps) but does not show these now.   Is there a secret to getting Speedfan to report the video info?
    Thanks for any help or insight you can give.  I have spent hours looking over the forums and have learned much!

    Well, I think I've sorted most of this out now.  The weird boot up (blank screens) seems to have cured itself so I will leave well enough alone.  I'm still tinkering with Speedfan, and after perusing a bunch more threads on that, I think I am reporting the graphics card temps.

  • Problem with AMD driver.

    Hello i need please help with this problem so i start explain what type of problem i have. I unninstalled old AMD Catalyst driver and Intel too. Then i installed newest from Intel.com and AMD.com. After upgrade AMD newest driver my graphics card changed name from AMD Radeon HD 7650M to AMD Radeon HD 7500/7600M. Doesnt hurt i just tell you what happened. Then i start think graphics card would work better if i unninstall those newest drivers and install from HP for Intel and AMD and then upgrade them with newest Intel and AMD drivers. For AMD it works but not for Intel so i have only newest driver. But it wasnt better so i wanted come back. I used all that time for unninstall drivers DDu Display Driver unninstaller.  And i deleted folder swsetup because it has too much GB and i thought theres only drivers which i dont need if i have them installed.  I used restore point there where i had newest drivers for Intel and AMD without older drivers installed because i thought it would be better then again reinstall drivers.  Now unfornately i have several problems. When i start computer i have 3 errors igfxpers.exe application errorThe application was unable to start correctly 0xc000007b. Click ok to close the applicationhkcmd.exe application errorThe application was unable.... 0xc000007bigfxtray.exe  application error The application was unable 0xc000007b... And what about AMD and Intel drivers?Intel works but about AMD i cant tell that same. From AMD driver stayed only few folders which showing Windows i have AMD catalyst driver installed but its not working. When i unninstall him to install new driver i have Standard VGA driver something like that. I looked at him in Device manager and he needs driver because he showing he cant find alone. And thats the problem. I dont know from where i can install driver for this. And yes that errors are too problems. I thanks for any reply which can fix this problem without reinstalling windows which i dont want. THanks

    Update: I unninstalled Intel and AMD driver with DDU now and i have video controller (VGA Compatible) and Radeon HD 7500/7600M.  In  device manager Radeon HD 7500/7600M i have now: System Windows cannot turn this hardware device because information about his configuration (in database Registry) are uncomplete or corrupted Code 19. I translated it from my language. What now?

  • Hp 4730s amd driver problem

    Hy,
    I have a HP ProBook 4730s.
    I use Win 7 Home Premium x64.
    I try to install the amd driver, but I can use only Intel Family video card.
    How can I install amd driver? (delete the intel, or something else?)
    Which AMD driver is good for my laptop?
    Thanks for the answers!
    Best Regards,
    Miklós

    Hi:
    What is the full model number of your g7?  What operating system?
    If it has the radeon 7670M, you only install the AMD driver, which installs the drivers for both the Intel and AMD GPU's..
    Never install the standalone Intel graphics driver.
    Uninstall all graphics drivers you installed, reboot,  and then install the AMD graphics driver only and reboot.

Maybe you are looking for

  • JPEG + Raw Seperated during Import

    Hi! I'm just starting out with Lightroom and ran into a problem.  Something makes me think it might be a bug, but not sure so I thought I'd ask.  When I imported files (did the copy) into LR, I created a folder structure based upon Year\Date\<origina

  • Database Migration and Cross platform migration

    Actually I am searching solution for following situation: as follows Server Name A : Operating System : IBM AIX Database Version Oracle 10.1.0..0 No. of Database Instances on this server -.. 2 Databases Server Name B Operating System : HP Unix Databa

  • XmlParse and XmlValidate

    I am getting an error thrown at me and I am not for sure why. I am using a cfc to send back XML code for the information required in a query. I have a dtd file that has been given to me by the company that is wanting this portal set up for them (chec

  • Regd Data Source text missing

    HI All, I have made changes in R/3 data source for 2LIS_13_VDITM and successfully transported to test server. Strangely when I replicate I could see the text of this data source in Dev system is missing. I tried to add the text in RSA6 change mode bu

  • Paint falling of

    Hello i bought an iPhone 5 for a few month ago and i have always used a cover. But my iPhone is starting to loose The paint on the back;-) Can u please tell me how to do;-)