G62-454ca won't turn on.power led and wireless network led keeps blinking every 3-4 seconds

Please help.when I try to turn on nothing happens.Only power LED and wireless network led keeps blinking every 4 seconds

According to the message you have recently posted I would like to confirm that this is a hardware issue and I strongly recommend you to immediately Contact HP Technical Support over the Phone for further assistance without any delay to get your Notebook diagnosed and serviced by an authorized HP Certified Engineer
You can also Check your warranty Here to verify the warranty status
Hope this helps, for any further queries reply to the post and feel free to join us again
**Click the KUDOS star on left to say Thanks**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Thank You,
K N R K
Although I am an HP employee, I am speaking for myself and not for HP

Similar Messages

  • Laptop won't start quickly but power wifi and caps lock light keeps blinking

    Hi, it has happened before too but rarely but nowadays it happens on daily purposes.
    When I switch on my laptop after leaving it for 8-9 hrs, it won't start up but instead power, wifi and caps lock light keep blinking. I tried removing battery and pressing power button for few minutes but nothing happens. Then i left it like that with lights blinking and after 15 20 minutes it booted. I did same yesterday too. I left it like that it booted after 20 minutes..so My question is "why is this happening? Is it a motherboard issue or is it because of cold moisturous weather here and laptop takes time to get warm up?" Should I show it to HP Service center?

    Hi @Nishant5788
    Welcome to the HP Support Forums. I see that you are having a problem getting your notebook to boot up normally. As for what is causing the problem the blinking Caps Lock should tell us what is causing the problem as it should be blinking in a pattern. This HP document Computer Does Not Start and LEDs blink has a chart that will tell you what the blink codes mean.
    This is most likely a hardware issue and you can give us a call regarding repair options.  You can reach HP Total Care at 1-800-474-6836 in North America or start here if you live outside of North America.
    Please click “Accept as Solution ” if you feel my post solved your issue.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Thank you,
    BHK6
    I work on behalf of HP

  • My iPod nano won't turn on power button stuck down.is this servicable?

    My iPod nano won't turn on power button stuck down.is this serviceable?This is the 6th gen model

    Hi Whackers!
    Here is a link that will help you get support for this product:
    Contact Apple for support and service
    http://support.apple.com/kb/he57
    Thanks for coming to the Apple Support Communities!
    Cheers,
    Braden

  • My Mac book pro won't turn on at all and when i put it to charge the light blinks, what should I do?

    My Mac book pro won't turn on at all and when i put it to charge the light blinks, what should I do?

    Yes if your model MBP has a removable battery.  If it does not: 
    Shut down the computer.
    Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
    On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
    Release all the keys and the power button at the same time.
    Press the power button to turn on the computer. 
    Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
    http://support.apple.com/kb/HT3964

  • TS3694 Ipad won't turn on at all, and is recognized by itunes as being in recovery mode- when I try to restore it stalls on the portion stating "preparing device for restore" and on the page it says "itunes is restoring the software." Been like this for a

    Ipad 4 won't turn on at all, and is recognized by itunes as being in recovery mode- when I try to restore it stalls on the portion stating "preparing device for restore" and on the page it says "itunes is restoring the software." Been like this for a day. I read the restore notes on apple, but this seems to be a little more unique than the standard recovery issues. Any ideas as to why I seem to keep stalling during the restore process?

    Couple of things I can think of before going to the Apple store.
    First, if you can, power off the iPad. Then connect it to the charger that came with the iPad and plug that into a known good wall outlet. Leave it there at least an hour then try to reset your device. Press and hold the Home and Sleep buttons simultaneously until the Apple logo appears. Let go of the buttons and let the device restart.
    Also, you mentioned you have the latest iTunes. But it would be good to check the actual version. If the iPad is running iOS 7 you need iTunes 11.1 or later.

  • My 1st generation Ipod touch won't turn on at all and whenever I press the buttons to reset it all I get is a white screen, or a white screen with black lines across.

    My 1st generation Ipod touch won't turn on at all and whenever I press the buttons to reset it all I get is a white screen, or a white screen with black lines across.Help pleaseeeeee!

    You can work through the five 5 R's of troubleshooting to rule out the possibility of corrupted software.
    http://www.apple.com/support/ipod/five_rs/
    It might also be a good idea to let the iPod's battery fully drain. Then charge it back up and restore it once more in iTunes.
    Otherwise, it's likely a hardware issue with the iPod's LCD display, meaning you'll need to take or send your iPod in for service either via Apple or a third party repair service. Here is Apple's repair pricing.
    http://www.apple.com/support/ipod/service/prices/
    Note that they don't actually repair the device, but exchange it for one of the same generation, model, and capacity.  A third party service will actually replace the damaged part for a little less.  Google "iPod screen repair" and you should get a number of results to work with.
    B-rock

  • My iPod touch won't turn on at all and if fully charged

    My iPod touch won't turn on at all and it's fully charged, what can I do?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • Mac book pro won't turn on black screen and capslock key on

    Macbook pro won't turn on - black screen and caps lock light is on

    Hi Daleobrien73,
    Welcome to Apple Support Communities.
    You may find some useful suggestions for troubleshooting your MacBook Pro in these articles:
    Apple computers: Troubleshooting issues with video on internal or external displays
    http://support.apple.com/kb/HT1573
    Troubleshooting: My computer won't turn on
    http://support.apple.com/kb/ts1367
    Best,
    Jeremy

  • Is there an App for turning the power on and off with the Iphone 5 as my button has stopped working

    Is there an App for turning the power on and off with the Iphone 5 as my button has stopped working

    No.  You'll need to bring your phone to Apple for evaluation and replacement.  If you're still within the warranty period and a hardware defect is identified, the phone will be replaced without charge.

  • My mac pro wont start. I push the power button and I get a click sound. A few seconds later another click sound and that it.

    My mac pro wont start. I push the power button and I get a click sound. A few seconds later another click sound and that it. I've tried different power plugs. Going direct into the wall, through a power strip. By iteslf, with other devices plugged in. I removed hard drives, and some RAM, and nothing. Sometimes it would not turn on, and then some minutes later it works. So its was sparatic, but now its been the same situation for three days where it wont turn on.
    I'm guessing power supply, but I wanted to see if anyone had a similar expereince and what the solution was, before I drag this beast to my local Apple store and have them look at it. Its a real pain to get it there and back and I want to be armed with some info for them. I already dragged this to them when it first started to do this, and of course it started up just fine for them. And you know if it works for the Genius then theres nothing wrong with. No matter what you explain to them.
    I figure if anyone had a the same problem and was able to resolve it, I can relate that experience to the Genius even if it start up for them.
    Thanks

    Try a SMC Reset using the extended method:
    Remove the AC power cord.
    Press the power-on button. [This drains the stored charge from the power supply]
    wait a quarter minute.
    Restore the power cord, being certain to JAM it into the socket, as the big block of rubber inhibits proper seating.
    wait a quarter minute
    attempt to power on.
    If no joy, examine the button battery half-hidden behind the graphics card. Remove it to measure the Voltage. A new battery should not cost over US$5, and measures a little over 3 Volts. BR-2032 is used in garage door opener controls and car door locks controls. The geeks at Radio Shack can measure it for you.

  • My Radio on my Nano won't pick up a signal.. I cennected my headphones and am in the middle of the city. Also my iPod keeps pausing every like 30 seconds.. What do I do?

    My Radio on my Nano won't pick up a signal.. I cennected my headphones and am in the middle of the city, so there are plenty of stations to find. Also my iPod keeps pausing every like 30 seconds when I try to listen to my music. I just got it for Christmas and already loaded it with songs.. What do I do?

    Push the headphone jack all the way in, you don't have it fully plugged in yet.

  • HT3205 Hi, 2011 MBP went on sleep mode and won't turn back on, charger and indicator shows green light, led in front on Trackpad lights on for 2 seconds then back off, MBP won't turn back on, what happened???.

    MBP went off and won't turn on again. Charger shows full battery ( green indicator) although I know I was close to low batt befor going off. What happened???

    Thank you for your detailed troubleshooting attempts.  Very helpful.  Sorry, I cannot read "logs."  My eyes just glass over on those things.  Hopefully, a knowledgeable user will come along shortly to decipher for you.
    I noticed from the pics that your location setting is "untitled."  Have you tried the "Automatic" setting?  Run the diagnostic test?  Results?
    Try the basics first:
       Change your router channel number.  Most times this works & is all you have to do.
    Disconnect & reconnect your modem.  unplug it for about 10 seconds.  Plug it back in.  Do the same for Apple’s routers.  Wait for everything to reboot.
    System Preferences>Network
    Click the Assist Me button.
    In the next window that pops up, click the Diagnostic button & do the necessary.
    Research Knowledge Base for network problems that pertain to the OS that is currently installed on your computer.   See these basic networking KB Articles:  http://support.apple.com/kb/HT1401 AirPort troubleshooting guide
    http://support.apple.com/kb/HT4628  Wi-Fi: How to troubleshoot Wi-Fi connectivity
    http://support.apple.com/kb/HT2712 Using network locations in Mac OS X
    Manually provided DNS server addresses are higher priority than DHCP's
    http://support.apple.com/kb/HT1714 Solutions for connecting to the Internet, setting up a small network, and troubleshooting
    ============================
    What to do when you can't connect to the Internet
    Also, run the Airport Utility app which is located inside the Utilities folder.
    =====================
    If using a  Linksys router, contact LinkSys Customer Support and/or post in their forums.
    If using Apple's Airport, please re-post over in one of the AirPort Forums.

  • My HP Mini 110-1050NR will not start. Power LED, WiFi LED and Hard drive LED Flash

    My Mini 110-1050NR just died... When I try to turn it on the Power Switch LED, the WiFi Switch LED and the Hard Drive LED just flash on and off. There's no specific count. They continue to flash until I disconnect the battery.

    Hi there
     I sent you  1 link
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00372748&tmp_task=solveCategory&cc=us&dlc=en&la...
    Check this out and let me know
    ****Click the White Kudos star to say thanks****
    ****Please mark Accept As Solution if it solves your problem****

  • HT1459 my ipod touch 4s won't turn on, reset, charge, and computer won't recognize it

    i was watching videos with my ipod. After a while i realized that my ipod was almost dead on power so when i was about to charge it, it turned off. i turned on and charged it and then i left it charging. when i came back my ipod was off and now it won't turn on even if i reset it or charge it from my pc. help!

    Try a different power outlet, then try restarting your iPod by holding down the on/off and the home buttons at the same time until you see the Apple logo. 

  • Ipod Shuffle won't turn on or charge and isn't recognized by the computer

    My Ipod shuffle won't charge and isn't recognized by the computer , it turned orange than stopped and won't charge or turn on since. Does anybody has a solution please ?

    I have exactly the same problem with both my ipod shuffles. That suggests to me that it is a problem with the ipods rather than my PC or computer software. I'm surprised that no Apple tech has suggested a solution yet.

Maybe you are looking for

  • Issue in Running the Assesement Cycle after upgrade.

    Hi We have a  Z Transaction Code for running actual assessment. We have migrated to ECC 6.0 from 4.6C. In the standard T Code KSU5, system was giving the message GA 627 "For the execution of assessments, distributions, periodic repostings or indirect

  • Any ideas on how to emulate this look (purposely bad looking video)?

    so i'm doing a very short sequence right now, and i thought it would be kind of interesting to have this short sequence have the same characteristics of the video quality of the old early 90s Sega CD based FMV games (for an example, i uploaded a shor

  • My printer started Flashing the"!" & message

    I need help on why my HP Officejet 5610 All-in-one is flashing "!" & messaging that my "Right cartridge isn't intended for this printer "when I just printed  with no problem. I reinstalled the cartridge but the printer warning hasn't changed and I ca

  • Custom itemRenderer - Bug?

    Hi, I have an example of some code that I can't figure out. What I'm doing may not be the best way to do what I want, but I believe is should work, and can't figure out why it doesn't. I have a datagrid with two columns, and the second column uses a

  • Usage rights

    Please can someone help me?  This is driving me nuts!  I have designed a form using Adobe Livecycle ES4.  I want users to be able to save and email filled out forms. I understand that I have to apply usage rights but I cannot see how to do this.  For