G710 / Win8.1 Pro - missing driver Microsoft ACPI-Compliant Embedded Controller

Just complete installing Win 8.1 Pro on my new G710. I got this message - missing driver Microsoft ACPI-Compliant Embedded Controller. Some users said that it can be solved with "Power Management" Driver but this one doesn't in Win 8.1 list. One user said that PM driver made his computer to slow down. Other users said that it is "Radio switch HW" driver but it is not relevant to G laptop. Any idea what to do?

hi
Yes this is the Detected device for Power Management.
This just allows you to control The system power distribution.
If you don't want to use Lenovo Power Management then that's just absolutely fine.
Windows has its own controls for power.
No need to wory about that ACPI\VEN_VPC&DEV_2004
This is one of my thread where the PM solved it
http://forums.lenovo.com/t5/Lenovo-3000-and-Essential/acpi-vpc-2004-driver-for-win-7-32bit-sp1-lenov...
Regards
Solid Cruver
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Similar Messages

Probook 4540s win8 64bit missing driver

in my laptop hp paviliong6 2303tx 32 bit windows8 is instaling but 64 bit windows 8 is not getting installed. in the error message it is showing that some files are missing so can you please help me to solve this problem because 32bit windws8 is not working properly in my laptop and i am not able to do my work properly my laptop is of 6 bit

broken linkPaul_Tikkanen wrote:
Hi, Asco: Below are the links to the drivers you need... http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5229455&prodNameId=5229457&swEnvOID=4132&swLang=13&mode=2&taskId=135&swItem=ob-115197-1 http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5229455&prodNameId=5229457&swEnvOID=4132&swLang=13&mode=2&taskId=135&swItem=ob-110946-1 http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=321957&prodSeriesId=5229455&prodNameId=5229457&swEnvOID=4132&swLang=13&mode=2&taskId=135&swItem=ob-110813-1 Best Regards, Paul

G710 Missing Lenovo ACPI-Compliant Virtual Power Controller Win8.1 x64

Hello,
In the driver section of G710 (i7CPU) there is no Lenovo ACPI-Compliant Virtual Power Controller(Energy menager) for Windows 8.1 x64.
Is it OK to use the one for Wndows 8 x64 instead?
Thank you!

Ivail wrote:
CBHedricks,
Thanks for your replay!
I have ton of questions for Lenovo tech support but as i read the forum here i see no point of wasting my time to create several new topics cause they just don't read it.
For example:
- Why the bios boot takes so long with that annoying animated "thing"? - my old 10 years old PC boots faster than G710.
- Why the turbo boost doesn't work without battery attached? - it should be the other way around - with battery but no AC pluged in, or user's choice at best.
And so on in that spirit...
Hmm... where to start... This is a community based forum, not a true tech support forum. Most of us are fellow users of Lenovo notebooks, computers and servers with differing degrees of education and skills. If you need support call them on the phone for best answers.
If your computer is running Windows 8.1 like mine, t can take longer to boot from power off state than from hibernate mode. Hibernation mode saves a working image of your computer's OS, drivers and running software, then enteres low power state. When you wake it up, it loads in the image, including loaded drivers and software and runs from where you left off. On cold start, windows has to discover hardware, load drivers and then software. Also - it processes any updates that are in the que for install after cold start.
Turbo Boost is a "overclocking" type of situation, one that takes more power to operate. This may explain why it needs two power sources to work correctly. Other than that - I have no clue.

Windows 7 RC installation on MacBook Pro: 'DVD drive device driver missing'

I'm trying to install the Windows 7 RC on my unibody MacBook Pro (purchased november 2008). I create the partition in Boot Camp, insert the install DVD, and restart the system. Then the Windows setup starts as it's supposed to (Windows is loading files). The install program launches fine, and I get to choose language settings.
And now it all fails. After I've chosen language settings, I get the message: "A required CD(DVD drive device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now."
Screenshot of the message: http://img25.imageshack.us/my.php?image=dsc00102yyh.jpg
I'm kinda baffled by this message. Obviously the drive can be use by the install program, but it still complains of a missing driver. I had no trouble installing the Windows 7 beta earlier this year.
I've done some googling, and it appears to be problem experienced by some others. Someone had the issue on an Asus machine (I think), and the solution was to download the driver and out it on a USB stick. But I can't seem to find the driver for the MBP DVD drive anywhere.
Has anyone else experienced this issue?

After countless days trying to solve this problem, I feel I can now add to the few solutions presented on the various forums of the internet. I'll post here because 1: i'm a mac user for everyday life although like most have as many pc's as well. 2: I already have a login for these forums!
okay so i tried everything from re-burns to usb install (which I could not complete because removable drives are not recognized by xp and I don't have a vista system). The problem for me ended up being because the DVD drive was plugged into the primary master ide channel. My hard drive for the unit i was installing windows on is sata and was configured as such (not bridged into IDE channel by bios). So in a nutshell it seems like the hard drive and the DVD drive are nit picky in regards to the IDE configuration of the drives themselves. This won't help for virtualization on a mac pro I realize but nonetheless is food for thought hopefully for all the people searching for " windows 7 install cd/dvd device driver missing " in their search engine!
Oh boy one more reason to love mac's
Christos

Satellite C55D - missing driver - ACPI-compliant Device

Hello,
I have a Satellite C55d-A-15H -   Windows 8.1 64bit
In Device Manager I have an entry marked "Other Devices" with a sub entry of 'Unknown Device !'
A right click on this and "properties" says:
Device Type: Other Devices
Manufacturer: Unknown
Location: On Microsoft ACPI-compliant System
The drivers are not installed (code 28)
There are no compatible drivers for this device
When checking update driver via on-line - it fails with "Windows was unable to install your unkown device"
Does anyone know please what's this all about and is there a driver - I've looked at the Toshiba driver list and can't seem to find anything
thank you
fip_man

Satellite C55D-A-15H (PSCGWE-03C00XEN)
Downloads here.
It's not a driver, but supplied by one of Toshiba's utilities. Try this one.
   Toshiba System Driver for Windows 8.1 - 64 Bit, 1.00.0030, 14/02/14
Probably makes no difference anyway.
-Jerry

MSI GE70 0NC - Missing driver HELP!

Hi people,
So I have owned my notebook since september, and just recently (December time i think) I started to get the BSOD when checking the stop codes i found that the code was linked to the video card failing. I checked my drivers to see if any needed updating or where missing since i installed windows 7 and got rid of 8 as I use this notebook as a cad and rendering station for work. I noticed i have two missing drivers that windows cant automatically install. one is a PCI Device for PCI bus 2, device 0, function 0. ( PCI bus 0 and 1 are my Intel 4000 and GTX 660m display adapters). and the driver status says "The drivers for this device are not installed. (Code 28) There is no driver selected for the device information set or element. To find a driver for this device, click Update Driver." the next missing driver is labelled as unknown device and upon reading its properties gives me this location info on Microsoft ACPI-Compliant Embedded Controller with the same status as before. I have been on the MSI downloads for my notebook and have downloaded all drivers/ BIOS/ Firmware that i can, with no success.
Can anyone help me find these missing drivers to see if ths stops the BSOD because i really cba sending it to MSI for them to say it's a software issue and my fault for changing to windows 7.
Thanks
Callum

chipset drivers: http://download.msi.com/nb_drivers/cs/cs_intel7series_9.3.0.1020_al00.zip
Intel HD card: http://download.msi.com/nb_drivers/vga/vga_intel_gt650m_gtx660m_9.17.10.2884_0x76849241_8764.zip
Nvidia drivers: http://download.msi.com/nb_drivers//vga/beta_nv_8.17.13.275_w764.zip
[or latest one from Nvidia.com]
all drivers at: http://www.msi.com/product/nb/GE70_0NC.html#/?div=Driver&os=Win7 64
you may have some device with no drivers for it, this is because Win8 BIOS/EC has addiction airplane modes,
which can't be used under Windows7, but that's not a reasons for any BSODs

W520 Base System Device PCI Bus 13 missing driver

About a month ago I had to do a full restore of my W520 as Windows was totally hosed. I thought that I had all of the right drivers at that time, but I notice that I have an item in Device Manager that is unrecognized. Does anyone know what this is?
Also, maybe related or maybe not, there is an Unknown device on Location "on Microsoft ACPI-Compliant Embedded Controller" Is this related or something else?
Thank you! Pete

That should be the "Lenovo PM Driver" Listed under your driver matrix as "Power Management" I can link to it once I can get the Driver support page working, as it is buggy right now.
W530(2436-CTO): i7-3720QM, nVidia Quadro K2000M,16GB RAM, 500 GB hard drive, 128GB mSATA SSD, Ubuntu 14.04 Gnome, Centrino Ultimate-N 6300.
Yoga 3 Pro: Intel Core-M 5Y70, Intel HD 5300, 8GB RAM, 128GB eMMC, Windows 8.1, Broadcom Wireless 802.11ac.

G770 on Microsoft ACPI-Compliant Embedded Controller

I have been searching everywhere on the Lenovo support/driver site and on the Internet. I just updated to Windows 8 Pro and have found that my device manager has an alert. It in in other devices, titled under unknown device with a heading of on Microsoft ACPI-Compliant Embedded Controller.
I am trying to find how to fix this. I had the same problem on a Toshiba but somehow I accidentally fix that laptop. But the Lenovo G770 has me stumped.
Please let me know what to do to correct this problem. I saw something about a Trusted Device or so but still can not find anything. I also searched Mircosoft but they tell you to go back to the laptop manufacturer.

Download Power management at this site http://download.lenovo.com/express/ddfm.html
Locate your model of your laptop and select "Power Management"

Slow PC w/ Win8 Pro

I just got a new computer to spec with Win8 Pro. It's on an old XP network that the company doesn't want to upgrade right now, but accessing anything on the network (especially email and drawings takes forever. Why?? Excerpts from Microsoft forums
below
==============================================================================
Original Title:
Windows 8
Since windows 8 no longer reads .eml email I've had to install Outlook 2010. I am on a XP network and get mail through the server. Outlook takes five minutes just to get to the server and then another few minutes per email to open. WHY!!!!!!!!!!! I
have the same problem trying to get to and open drawings on our server.
I had an older machine that could not work with the bigger 3D files we started working with. I opted for a new machine with window 8 because I thought that it was better especially with more ram. I wish I had my old machine back.
Is there a way to get everything on my machine working or am I screwed??????
==============================================================================
Since it's the network operations (like opening files from your server or Outlook email), it sounds like the network is your problem. XP is 13 years old, sounds like that server is due for an update itself. It's bottle-necking everything.
But also, many problems in Windows 8.0 (which is already 3 years old itself) and were fixed in the 8.1 update. I notice selected that you haven't got the update yet. Please open the Windows Store app on your tablet and touch the "Get Windows
8.1 now" button that you see to get the update.
And finally, you might want to take a quick look at :
==============================================================================
Thank you for your reply. I realize that the XP server is old and should be retired but like so many other companies it's hard for them to justify the time and expense to change.
Having said that what I don't understand is that there are 150+ computers here, all of them running Windows previous to Vista. When they access the server it acts like the files are on the hard drive. What I mean is you can access the daily email directory
and it opens almost immediately (1-2 sec.). When you select and open an email it's the same thing. But on my new Win 8 Pro machine I click on the daily email Icon and wait 15-40 sec. to load. (I've timed it), then you click on the folder for today you
can wait as long as three minutes to load the emails depending on how many are there.
Because Win 8 deleted anything to read .eml files I had to get Outlook 2010. Now to open an email I have to click on the email which now loads Outlook, (sometimes 5 minutes) before the email opens. Don't even try to open a second email with Outlook open,
it WILL lockup. SO you close Outlook and go to the second email. Just today it took me from 8:10am to 10:05am to open and read 11 emails, no response to any just open and read.
This is supposed to be the latest and greatest (LOL) from Microsoft. There must be a way for this NEW machine to act like the old outdated computers and just open an email.
By the way, I turned off search indexing and looked at the startup programs that load. All of them were for Microsoft to run. This computer has no games, bell are whistles. I've loaded the 2D and 3D software that I use for design and nothing else. (EXCEPT
Outlook 2010 now). There was absolutely no difference in the performance and the CPU barely registers any use except when I have the 3D software crunching a large project.

Here is the forum for you.
Just to remind, Win8.1 is the latest recommended version, and the next one will be "Windows 10". Windows 8 is obsolete and should be upgraded.
-- pa

Cannot boot if HP ENVY Bios Virtualization enabled for Win8 Pro Hyper-V

HP Envy H8-1414 desktop machine (just bought last week)
Upgraded from Win8 to Win8 Pro
Win8 Pro has Hyper-V just like a Server OS, so I
- enabled Virtualizaiton in the Bios
- in Win8 Pro, Control Panel, Programs and Features, Add/Remove Windows Software
- enabled Hyper-V
- reboot
- won't get past Window logo with rotating "busy" circle underneath
Power off, into BIOS, disable Virtualization
Machine now boots, but Hyper-V won't work.
So, looks like the BIOD supports virtualization, but not for Windows 8.

To add some more details....
The HP specs for this machine say Gigabyte motherboard, but you can't find the model on Gigabyte's web site, and Gigabyte won't support it (I tried, they said it is not theirs - great). Anyway, some Gigabyte boards show a similar problem and the workaround is to disable USB 3 host in the bios, but this machine's BIOS does not show this option.
When I spoke with HP, they very quickly told me that I needed to call Microsoft. They would not provide support for this BIOS issue. Microsoft seemed pretty surprised that they would pass the buck so quickly and I can at least say that they are being very attentive to the problem.
With Microsoft support, they had me recreate the problem and wanted me to let it hang on the Windows logo screen for one hour. Then, they had me run a tool which dumps a bunch of logs and diagnostics to some files which I have sent to them. That's the most recent step so I'm waiting to hear back from them.
I've used Hyper-V on a buch of HP machines with no problems, but none of them with Windows 8. I'm tempted to put in another drive and install Windows 2008 R2 or 2012 and see if Hyper-V works.
I've typically purchased HP machines (for work, so more than an individual woudl buy) because they have been reliable but I've never attempted to use HP support. I was surprised how poor it was. I would think that this would be an issue they would want to resolve and I expect it may be possible with a BIOS update.

Proxim ORiNOCO 8482 11a/b/g Wirelss PCI Card Windows 7 Pro x64 Driver Request

Hello Microsoft Community,
I'm trying to install the following:
Product ID: Proxim ORiNOCO 8482 11a/b/g Wirelss PCI Card
Name: ORiNOCO Wireless PCI Network Card
Device ID: PCI\VEN_168C&DEV_0013&SUBSYS_0A1014B7, PCI\VEN_168C&DEV_0013&SUBSYS_0A6014B7.
Problem: None of the drivers for Windows 7 X64 has worked to install in devmgmt.msc Please advise where Windows 7 Drivers can be downloaded.
[Please note I've tried the following and had no success: 4.2_JP2_Vista , 4.2_Vista , 4.2_whql , ORiNOCO_v31219 , V2.2.0 software , wpn311_2_0_setup]
I have submitted the following to Proxim Tech Support :
Support Request Submitted: 20284
Thank you! Your support request has been submitted and one of our technical support members will be in touch shortly.
Details
Subject
Proxim ORiNOCO 8482 11a/b/g Wirelss PCI Card Windows 7 Pro x64 Driver Request
Status
New
Severity
Medium
Type
Support Request
Reason
Driver / Software Installation
Request Date
Jan 12, 2015 05:31:26 am PST
Product
Serial Number
Warranty / ServPak
N/A
ServPak Reference
Description
Hello Proxim Tech Support, Product ID: Proxim ORiNOCO 8482 11a/b/g Wirelss PCI Card Name: ORiNOCO Wireless PCI Network Card Device ID: PCI\VEN_168C&DEV_0013&SUBSYS_0A1014B7, PCI\VEN_168C&DEV_0013&SUBSYS_0A6014B7. Problem:
None of the drivers for Windows 7 X64 has worked to install in devmgmt.msc Please advise where Windows 7 Drivers can be downloaded. Thanks, Kent C.
Proxim ORiNOCO 8482 11a/b/g Wirelss PCI Card Windows 7 Pro x64 Driver Request
Status
New
Severity
Medium
Type
Support Request
Reason
Driver / Software Installation
Request Date
Jan 12, 2015 05:31:26 am PST
Product
Serial Number
Warranty / ServPak
N/A
I will update thread with their reply as nothing, even Driver Genius Professional 11 has located the actual working driver. Once an update is verified, I will post back to this thread since I couldn't find the right answer online.
THIS BTW I TESTED IS INCORRECT [You may verify if you don't believe such] :
http://www.experts-exchange.com/Software/System_Utilities/Q_26292317.html <- That didn't work [Found driver online via Google] and link isn't working anymore in that post.
This is related to this thread here:
https://social.technet.microsoft.com/Forums/windows/en-US/668ac1f0-4560-4bd3-8848-c4fcdc70c10a/wanted-atheros-driver-for-windows-7-x64?forum=w7itprohardware
Any assistance would be appreciated! Thanks..
Kent C.

Hi,
About this issue, you need conatct proxim support to confirm if it could works fine in WIndows 7 platform and how to get the proper driver package.
Karen Hu
TechNet Community Support

My MacBook Pro hard drive is almost full and I wish to store my Aperture Library on an external drive, how do I do this and is the use of USB2 suitable or do I need to use a Firewire external hard drive?

My MacBook Pro hard drive is almost full and I wish to store my Aperture Library on an external drive, how do I do this and is the use of USB2 suitable or do I need to use a Firewire external hard drive?

You'll get better performance if you use a Firewire hard drive (especially if you buy a 7200 RPM drive). Firewire's IO speed is significantly faster than USB 2. USB 2 has a theoretical max speed of 480 Mbps except that it has extremely high over-head. The fastest speeds you can typically get are about 300 Mbps. Firewire, on the other hand, has very little overhead. The fastest speeds you can get are very nearly 800 Mbps. You will typically be constrained by the maximum read/write speed of the drive, not the speed of the I/O on the Firewire bus. Now if you had one of those nice shiny new Macs with the Thunderbolt I/O and a Thunderbolt drive (Light Peak) ... I think they alter space and time so that your data arrives before you know you want it.
Also... unless you want to buy a solid state drive (very expensive), try to keep your hard drives from becoming much more than about 60% full if you want great performance. A nearly "full" hard drive is, on average, only about half as fast as the same hard drive when nearly empty.
USB 2 will work perfectly fine... just not as fast.
Also... it's much safer to move the entire Aperture library than to "relocate masters". Your images must be managed. You can Aperture manage them, or you can manage them. But someone has to manage them. If you "relocate" them so that they are no longer stored inside the Aperture library then you'll need to work out a system of how you decide to organize things and it's critically important that you don't start moving files around or deleting things without Aperture's knowledge. If you do, you'll break the links to your masters and start having problems with missing masters. If you have Aperture manage the library then you don't need to worry about any of that stuff.... it's safer.
Do make backups (use the Aperture Vault or use some other backup program, but make sure you back up your work if you care about it.) There are only two kinds of hard drives in the world: (1) those that have failed and (2) those that are going to fail. There are no exceptions to this rule. Hard drives are cheap. Backup software is built into Aperture and into your Mac.

[[DataDirect][ODBC SQL Server Wire Protocol driver][Microsoft SQL Server]Column name or number of supplied values does not match table definition.]

Hii ..
need help on this ..
This what I am doing ..
I am using a DATAEXPORT function to export level0 data from my essbase 11.1.2.2 to Microsoft SQL 2008 tables.
So what I did first I exported the level0 data to a flat file using DATAEXPORT and the created the SQL columns by the same in that order only in my SQL table.
When I run it fails with this error:
ODBC Layer Error: [21S01] ==> [[DataDirect][ODBC SQL Server Wire Protocol driver][Microsoft SQL Server]Column name or number of supplied values does not match table definition.]
[Tue Jul 23 18:26:07 2013]Local/dataexp/dataexp/admin@Native Directory/1209813312/Info(1021014)
ODBC Layer Error: Native Error code [213]
[Tue Jul 23 18:26:07 2013]Local/dataexp/dataexp/admin@Native Directory/1209813312/Error(1012085)
Unable to export data to SQL table [dataexp]. Check the Essbase server log and the system console to determine the cause of the problem.
[Tue Jul 23 18:26:07 2013]Local/dataexp/dataexp/admin@Native Directory/1209813312/Info(1021002)
SQL Connection is Freed
[Tue Jul 23 18:26:07 2013]Local/dataexp/dataexp/admin@Native Directory/1209813312/Warning(1080014)
Transaction [ 0x1c50001( 0x51ee7d66.0x80342 ) ] aborted due to status [1012085].
[Tue Jul 23 18:26:07 2013]Local/dataexp/dataexp/admin@Native Directory/1209813312/Info(1012579)
Total Calc Elapsed Time for [test.csc] : [1.44] seconds
=============================================================
I did a simple test on my Sample.basic application then ..
loaded the calc data to it and then used the below script to export to a flat file
//ESS_LOCALE English_UnitedStates.Latin1@Binary
SET DATAEXPORTOPTIONS
                DataExportLevel "Level0";
                DataExportOverwriteFile ON;
                DataExportColFormat OFF;
                DataExportDimHeader OFF;
FIX(
            "Jan",
            "Sales",
            "Actual"
/*DATAEXPORT "File" "," "/home/hypadmin/samtest.txt";*/
DATAEXPORT "DSN" "Abhitest" "sample" "sa" "welcome1";
ENDFIX
out put as below:
"Sales"
"100-30","California"
"Jan","Actual",145
Now In sql I created only 3 columns with name Jan/Sales/Actual and when I run this script again with comments removed .. I get the same error as what I have got in my first test case with other application ..
but when I create the columns with same name as what its in export
Sales/100-30/Califirnia/Jan/Actual
It created the new rows successfully ..
So with this I think the error which I am getting with my other application might be because of the same column issue .. but then I have created all the columns by looking at the export file only as I did in sample ..
Any idea would be helpful ..
Thanks
Abhishek
I

First make sure you add
DataExportRelationalFile ON;
to your set commands it is missing
I alwats like to also add
DataExportColHeader dimensionName;
so I am sure what dimension is getting put into the columns.
Then count the number of dimensions in your outline (exclude attribute dimensions). You need at least that many columns in your table -1 + the number of members you will be returning as columns in the export
Taking your example Sample basic has 5 dimensions
Measures
Years
Scenario
Product
Market
Since you did not specify a dataexportcolheader it took the dense dimension Scenario as the columns. Your fix statement is limiting that to one member. Doing the math
5 -1 + 1 = 5 columns in your table which is what you found works. Suppose you fixed on bothe Actual and budget in scenario then you would need 6 columns 5 -1 +2

Missing driver problem

hey cisco i was just setting up a network share on my wifes vista computer and got a missing driver and it seems to be a often occuring problem for many people please have your support team take a look at this http://answers.microsoft.com/en-us/windows/forum/windows_vista-hardware/windows-needs-to-install-dri... ... it seems someone forgot to write a vista driver ... i have another question for you lol how is it no matter what i do i always run into every problem imaginable going on 20 years now?

That’s simple enough. Uninstall Cisco Connect from your computer, and download and install the latest one from homesupport.cisco.com

Apple laser writer pro 630 driver for windows vista 64 bit on a PC

I've just bought a new PC running Vista 64bit and am unable to find Apple laser writer pro 630 driver for it -- it ran fine on my old PC running XP -- HELP!

Hi and welcome to Discussions,
found this:
You can install the XP Apple drivers onto Vista if you have the XP
installation CD.
Use the have disk option in the Add Printer Wizard.
point to the CD \i386 directory
Alan Morris
Windows Printing Team
Search the Microsoft
Knowledge Base here:
http://support.microsoft.com/default.aspx?scid=fh;[ln];kbhowto
here: http://www.vistax64.com/vista-print-fax-scan/43484-apple-laserwriter-printer.htm l
Hope it helps
Stefan

G710 / Win8.1 Pro - missing driver Microsoft ACPI-Compl​iant Embedded Controller

Similar Messages

Maybe you are looking for

G710 / Win8.1 Pro - missing driver Microsoft ACPI-Compliant Embedded Controller