Gameport header pinout for Audigy M

Hey everyone, I could use a little help. I have the Audigy MP3+ soundcard, but I've lost my gameport /MIDI connector for it. Does anyone have the pinout for teh connector on the sound card itself so I can make a new one? Or know how I can go about getting a new connector and bracket. (bracket not really nessecary) I'm fairly good at soldering and have the parts to do it, and while they have the pinout for the connector itself, nothing is listed for the connector on the board. ANy help is appreciated.

JSladen wrote:
Does anybody know the pinout for the 44 pin D-Sub found on the back of the Audigy platinum Ex dri've?
I'm trying to build a cable to connect the dri've directly to my card, as I don't seem to be able to buy the daughter card (SB00b) anywhere.
(If anyone does know where I can get a daughter card that would be really useful as well)
Only that can be found is pinout table for AUD_EXT, but it's not 44 pin but 40 pin connector. You can find it from Creative Support/KnowledgeBase by searching AUD_EXT.
.jtp

Similar Messages

Pinout for Audigy platinum Ex Dr

Does anybody know the pinout for the 44 pin D-Sub found on the back of the Audigy platinum Ex dri've?
I'm trying to build a cable to connect the dri've directly to my card, as I don't seem to be able to buy the daughter card (SB00b) anywhere.
(If anyone does know where I can get a daughter card that would be really useful as well)

JSladen wrote:
Does anybody know the pinout for the 44 pin D-Sub found on the back of the Audigy platinum Ex dri've?
I'm trying to build a cable to connect the dri've directly to my card, as I don't seem to be able to buy the daughter card (SB00b) anywhere.
(If anyone does know where I can get a daughter card that would be really useful as well)
Only that can be found is pinout table for AUD_EXT, but it's not 44 pin but 40 pin connector. You can find it from Creative Support/KnowledgeBase by searching AUD_EXT.
.jtp

Audigy platinum pinouts for dri

I have an original Audigy platinum with the connections for a dri've bay - which I did not purchase. My new case allows for a front panel microphone and headphone (as well as other connections) in addition to the back panel ones. After installing the audigy card in it - these connections no longer work =(
Since the dri've bay comes with mircorphoone and headphone outputs - I assume there are appropriate pins on the dri've bay connection that (if identified) - could be connected to my computers froont panel enabeling the use of these with the audigy card and not just the sound system proved with the mobo. Does someone have accurate information about the pinouts for the dri'vebay that are on the Audigy card? And, would you be gracious enough to supply me with this information.
Thanks,
Jim

Greetings again and thank you Jeremy for the fast response - FYI I did look for this information on the web before coming here to post. Based on what I gathered from the article you attached was that: . I could connect my front panel headset connections to pins 0, and 2 ( General purpose output , general purpose output 2 and ground) (or should they go to the ones labeled spdif?) 2. I could connect the microphone connections to pins 5 and 6 (spdif input signal and ground) I hate to be a pain but I really don't feel like messing up anything either and maybe a moment of your time can save me a lot of issues later. Thanks in advance!!! Jim Here is the content from the post so you don't have to go back and look: This is for the Sound Blaster Li've and Sound Blaster Audigy Series Only. Not the Sound Blaster Audigy 2 Series. Pin-Outs Pin Name Description VCC +5V power supply 2 VCC +5V power supply 3 GND Ground 4 AC97CLK 24.5 MHz clock output 5 GND Ground 6 GP_SPDIFIN#2 SPDIF input signal 7 GND Ground 8 GND Ground 9 SPDIFO#3 SPDIF out Signal 0 GPO General Purpose Output # GPO2 General Purpose Output #2 2 GND Ground 3 GPO0 General Purpose Output #0 4 GND Ground 5 GP_ SPDIFIN SPDIF Input signal 6 GND Ground 7 GPDIFO#0 SPDIF Out signal 8 GND Ground 9 SPDIFO# SPDIF Out signal 20 GND Ground 2 GND Ground 22 SPDIFO SPDIF Out signal 23 GPI0 Digital Input (GP Input 0; Reserved) 24 GPI Digital Input (GP Input ; Reserved) 25 OUTMIDI MIDI Output 26 GND Ground 27 INMIDI MIDI Input 28 GND Ground 29 KEY no pin 30 KEY no pin 3 ADCSDO2 I2S audio data input 32 GND Ground 33 ADCSDO I2S audio data input. 34 GND Ground 35 ADCSDO0 I2S audio data input 36 GND Ground 37 I2SCLK I2S serial bit clock 38 GND Ground 39 I2SFS Frame sync. 40 GND GroundMessage Edited by hickerso on 0-27-2005 09:07 PM

Cable for Audigy platinum Ex

Hi,
is it possible to buy a cable between the audigy card and the external box? I have somehow lost it...
Thanks for an answer,
Filip from Czech Republic

JSladen wrote:
Does anybody know the pinout for the 44 pin D-Sub found on the back of the Audigy platinum Ex dri've?
I'm trying to build a cable to connect the dri've directly to my card, as I don't seem to be able to buy the daughter card (SB00b) anywhere.
(If anyone does know where I can get a daughter card that would be really useful as well)
Only that can be found is pinout table for AUD_EXT, but it's not 44 pin but 40 pin connector. You can find it from Creative Support/KnowledgeBase by searching AUD_EXT.
.jtp

HP DC5700 P5BW-BTX Motherboard - front panel header pinout

Greetings all ...
I have been searching everywhere for the front panel header pinout of the P5BW-BTX Motherboard that is in the HP DC5700.
Does anyone have this? It is unfortunately omitted from all the hardware and technical manuals.
Thanks in advance
Kenneth A Spencer
[You never know, you might learn something that you never knew: from my new book: All about your Computer.]
This question was solved.
View Solution.

OK: for future reference BeatGr et al, here is the pinout for the front panel header connector on the HP P5BW-BTX motherboard:
LED HDD 1 10 LED PWR
LED HDD 2 11 LED PWR
NC       3 12 SWI PWR
NC       4 13 SWI PWR
NC       5 14 NC
NC       6 15 NC
->18     7 16 NO PIN
NC       8 17 NC
NC       9 18 ->7 (pins 7 and 18 are permanently shorted)
I am not sure of the significance of the shorted pins 7 and 18 - maybe someone else knows.
Best wishes,
Kenneth Spencer
[You never know, you might learn something that you never knew: from my new book: All about your Computer. 230 pages, perfect bound. First 57 pages are on Google Books.]

USB pinout for DC7100 motherboard

I've looked everwhere and can't find the USB pinout for the P24 header on the motherboard. I've had to put the mobo into a new case. Can someone show me where this info is located? Thanks.
PS. How do I change my email address????
|
+-- JDMils
|

Well, let me clear that there's no seperate power connector to USB from the power supply. There would be a pin set on the motherboard which could be connected to the USB card reader or the port. The pin would be usually named as USB-1 or USB-2.
You did not mention about the product info on the forum, if you know the model number, follow the below steps to check the exact port on the motherboard.
1. Open www.hp.com
2. On the top search field, type: model number of the PC, and press enter.
3. Open the product specifications page, and find the name of the motherboard.
4. Search with the name of the motherboard in HP website, you will see the motherboard layout with labellings.
This will clealy show the port and the connection to you.

It is necessary to create one header data for each file to be sent to CDFS.

hi GUYS
my sce anrio is FILE-XI-PROXY
REQUIREMENT IS
SOURCE FILE                      TARGET FILE WILL BE
H1                                             H1                        H1                    H1
I1                                               I1                         I2                      I3
I2                                                F1                        F1                    F1
I3
F1
It is necessary to create one header data for each file to be sent to TARGET. Each file will be related to only one SAP Company Code.
Thanks
NAG

aa

How to make Delivery block at Sales Order Header level for specific materia

Hi,
My client want to create a delivery block EDI order at the Order Header level for specific materials
How can we achieve this.

Dear Varada rajan
Go to material master, select "Sales: sales org.1" view and assign "01" against the field "DChain-spec. status" and save. By assigning, for a particular sales area, you can block that material.
Now go to OVSU select 01 and assign "B" against the field "Block delivery".
Now create a sale order and post the outcome.
thanks
G. Lakshmipathi

Issue in PA - Header Modifications for IT0105

Hi All,
I have done header modifications for PA30 Screen, IT0000, IT0001 and IT 0105 (Communications) and for IT0021.
I am able to get the details of PA, PSA, EG and ESG in the header details.
But when an employee PA/PSA/EG/ESG has changed becoz of any action, the same information is not shown in IT0105 header details. System is picking up the old PA/PSA/EG/ESG details only.
If i change the start date in IT0105 as per the last action run, then it is picking up the updated information. Where in the employee IT0105 (Mail ID/ Mobile Num) remains the same from his Date of joining.
But as the action is been run and the PA/PSA/EG/ESG has already changed the same information should be updated automatically.
Request you to guide me to get the updated PA/PSA/EG/ESG in header details of IT0105.
Kind Regards
Nag
09581555404

Dear Nagesh,
what our Team members suggested is correct.
check the F1 help of Field CHOOSE DATA in Table V_582A_B.
F1 help.
Use
If you set the Choose Data indicator, you will use data that is valid for the start date of the current processed, or displayed, infotype record to structure the infotype header.
If you do not set the Choose Data indicator, the data that is valid for the system date will be used to structure the infotype header.
so uncheck the CHOOSE DATA field
regards,
mohammed

How to include header name for the fields in application server

Hiiii Experts,
                      LOOP AT fp_i_wwcmp INTO fp_wa_wwcmp.
      CONCATENATE fp_wa_wwcmp-pernr
                   fp_wa_wwcmp-etype
                   fp_wa_wwcmp-maxbt
                   fp_wa_wwcmp-epayperiod
                   fp_wa_wwcmp-currencyid
                   INTO l_v_data SEPARATED BY l_v_char_tab.
i need to insert header names for etype,maxbt,epayperiod,currencyid which are needed to be transfer to application server.
regards,
kasyap
Edited by: Harish Kasyap on Sep 18, 2009 2:49 PM

hiiiii clemens thanks a lot for ur reply,
                                                           this is not an alv report,the output is directly transfered into application server AL11.
and i have used this statement
CONCATENATE 'ID'
                'EpayType'
                'EpayAmount'
                'EpayPeriod'
                'CurrencyID'
                   INTO l_v_data SEPARATED BY l_v_char_tab.
transfer l_V_data.
is this the rite one
regards,
kasyap

I'm working in Pages 4.1. I want to add text to a header but for it to appear only on that page in stead of duplicating itself on all pages of the document. How can this be done?

I'm working in Pages 4.1. I want to add text to a header but for it to appear only on that page in stead of duplicating itself on all pages of the document. Can this be done?

See this thread: https://discussions.apple.com/thread/3728197?start=0&tstart=0

When I open a file it normally opens in 12.5% stated on the header. For some reason, it now opens with 100+% on the header and is much smaller in size. How do I go back to the first option I noted? I use AP to work on blueprints for measuring so the accur

When I open a file it normally opens in 12.5% stated on the header. For some reason, it now opens with 100+% on the header and is much smaller in size. How do I go back to the first option I noted? I use AP to work on blueprints for measuring so the accuracy matters. Any direction would be greatly appreciated. Thank you.

Are the image all the same size the % files open into a document seems to vary with the number of pixels the image being opened has. Check the Image size.

What is the pinout for the 6602 relative to the 'D' connector.

I am developing a custom board to connect with the PCI-6602 Counter/Timer card. I will use the SH68-68-D1 Shielded Cable, 68-pins, 2 m to connect from the 6602 to the custom board. What I need to know is what is the pinout relative to the 'D' connector. The manual shows the connector as a rectangle.
Thanks,
Tony

Hi Tony,
The routing from the PCI-6602 through the SH68-68-D1 is one-to-one, so I believe that all you should need is the pinout for the 6602. This is shown below.
This information can be found in Measurement & Automation Explorer (MAX) by right-clicking on the device and selecting "Device Pinouts".
I hope this is what you needed. Post back if you have further questions.
Ed W.
Applications Engineer
National Instruments
Message Edited by Ed W on 12-13-2006 04:14 PM
Message Edited by Ed W on 12-13-2006 04:14 PM

How can i add Document Header Text for s_alr_87012357

Hi Gurus
How can i add Document Header Text for s_alr_87012357(Advance Return for Tax on Sales/Purchases).do i need change the standard program or is there any alternate to do this please help me out.

i found it .its in output list and i did change the layout settings.thanks

Long Time: Fill Internal Header Table for VBUK via Doc. Flow Predeces

Good Morning Support,
I have installed DMIS (2006_1_620) and DMIS_CNT (2006_1_620), both atthe level of SP = 13. Data Base = Informix.
The activity "Header Fill Internal Table for Predicting Flow VBUK via Doc" is taking a long time in execution.
I wanted to create an index to improve performance according to the note 1256679 but I can not because the tables VBFA and VBFCL are "Table cluster" and I have no way to create index.
Any suggestions?I open the remote connection.
Thanks,
Hugo.

Hello Hugo,
There are 2 ways out of this :
1. Either convert the Cluster Table to Transparent Table.
2. Enable Cluster Handling by setting P_CLU to Y. But in this case, you will have to set the parameter for all the 3 activities for VBUK i.e.
a) Fill Internal Header Table for Table VBUK (Initial) -
> TD05X_FILL_VBUK
b) Fill Internal Header Table for Table VBUK via Document Flow -
> TD05X_FILL_VBUK_1
c) Fill Internal Header Table for VBUK via Doc. Flow Predeces. -
> TD05X_FILL_VBUK_2
Then re-run the previous activities in the above order so that the cluster gets filled.
Hope this helps.
Regards,
Suman

Gameport header pinout for Audigy M

Similar Messages

Maybe you are looking for