Gateway 24"lcd with 9200 card?

I'm thinking about buying a Gateway 24" lcd to connect to my ATi 9200 video card. Is this a good choice? I've never used an lcd monitor and wondered if the 128 meg 9200 card would work ok? Thanks, Tom

Hi Again! I bought the 24" Gateway and LOVE it!!!! It's so much easier on my eyes than my old crt was too. Tom

Similar Messages

  • Will a 9200 card run 24"lcd?

    Hi! I have a radeon 9200 128 meg video card in my Sawtooth and wonder if I can attach a new 24" lcd monitor to it with good results. Thanks, Tom

    I found your old posting on the board and wanted to ask you a question...
    I have a Sawtooth 500 and was considering a Radeon 9200 card...
    have you had any problems and what screen and size did you end up with.
    I am converting from a 20 inch CRT and need some advice.
    There have been some negative reports about this card.
    Thank you, Tom

  • LMS 4.2.3 - C6500 VSS - Issue with inline card on secondary chassis

    Hello,
    We are currently setting up a fresh new LMS 4.2.3 server to administrate a 90 LAN-device-perimiter. Installation is OK (on a Windows Server), devices are up, monitored and their configurations archived.
    The core switches are Catalyst 6506 VSS (s2t54-IPSERVICESK9-M - 15.1(1)SY) including 2 inlines cards :
    - WS-C6505E-SUP2T
    - WS-X6824-SFP-2T
    There is an issue with line card WS-X6824-SFP-2T recognition on secondary chassis only. We updated the last software packages for LMS (via Admin > Software Center > Device Update) and situation improved but still, it is not behaving as excepted.
    Impact : Topology, Ciscoview and Device Center for C6506-VSS do not show the card and links on the WS-X6824-SFP-2T of secondary chassis.
    Do you have this issue as well ? Any direction or help ?
    I am afraid of a potential bug...
    Rgds,
    Yoann

    When you were placing the internal test calls, where was your phone located?   The RTP streams are usually only set up between the two endpoints (assuming no transcoder or MTP is used).
    Have you have already checked calls between IP phones at your central site (where Unity is located) and IP Phones at site A?   Are these working fine?   If not, then it's likely you do have a QoS issue over the WAN to Site A.
    Have you confirmed whether or not calls from the PSTN gateway at site A experience any voice QoS issues when transferred to an IP Phone at the central site?
    Is the same codec is being used for the MGCP gateway as for IP Phones at that site (check the Region settings for the Device Pool it's in)?
    If these things have all been checked, then you may want to consider collecting a simultaneous sniffer trace from each end of a single call, and comparing what's seen at the two endpoints.
    Kind regards,
    Craig

  • Help with Graphics card purchase

    I'm planning on buying a new graphics card for my creaky old Mac (G4 400 MHz PowerPC, CRT display, running Tiger). Mainly because I do a lot of 3D modelling/rendering work and I think it would improve the experience I have with the apps that I use daily. Apart from not being up to spec for modern games graphics my Mac works pretty darn well (probably because I have a shed-load of RAM), so I'm not planning on getting a new Mac any time soon. I just want to cheaply soup-up this one.
    I'm looking at getting either the 'ATI Radeon 9600 Pro - Mac', or possibly the cheaper 'ATI Radeon 9200 Mac Edition'.
    After looking online I have seen that users of both have reported some problems. The 9600 has been reported not to work with some displays and the 9200 has been reported to make DVD act really badly.
    So my questions are roughly:
    Have these issues been resolved? Have you experienced any problems upgrading your old Mac with these cards? Would these cards make a marked difference to my 3D modelling/rendering apps? What graphics card would you recommend?
    Thanks in advance.

    Does your Mac use a AGP (Advanced Graphics Processor) slot?
    Based on the 400MHz you mentioned, is is probably a "Gigabit Ethernet" model, which has a 2X AGP slot.
    If not, your only option is the ATI Radeon 9200 128 MB PCI Mac Edition card. I hadn't heard about any DVD playback problems with this card. ATI says it will not work with OS 9 in G4 "Digital Audio" and "Gigabit Ethernet" models.
    If you do have AGP you definitely want to use it. The ATI Radeon 9800 Pro Mac Edition 256MB AGP works with 2X or 4X AGP models. This card will give the best performance.
    The ATI Radeon 9600 Mac & PC Edition 256MB is for 4X or 8X AGP slots. Even if you do have a 4X AGP slot, this card may not work in your system because of its power consumption. ATI says it is not compatible with "Digital Audio" and "Quicksilver" models. That leaves the MDD (Mirrored Drive Door) as the only G4 model with 4X AGP that it will work in reliably.

  • Uploading files to SAP using HTML5 /AJAX/Gateway media links with real-time progress bar

    Hi All,
    Check out the blog post 'Uploading files to SAP using HTML5 /AJAX/Gateway media links with real-time progress bar'
    Uploading files to SAP using HTML5 /AJAX/Gateway media links with real-time progress bar
    Regards
    Prabaharan

    aplay -l
    **** List of PLAYBACK Hardware Devices ****
    card 0: NVidia [HDA NVidia], device 3: NVIDIA HDMI [NVIDIA HDMI]
    Subdevices: 1/1
    Subdevice #0: subdevice #0
    Which correspondents fine with the
    device "hw:0,3"
    in my mpd.conf alsa section.
    Also sound worked fine withh this config before I started installing ffmpeg-svn and alikes
    hokasch:
    I tried changing the mixer to "Master" but that did not change much.

  • Having issues with your Card Readers in Windows 7 not working? Here's resolution!

    You do not need drivers for the card reader. There are NO Windows 7 drivers.
    (1.) Click on the Start button and then choose Control Panel.
    (2.) Click on the Administrative Tools a window will open.
    (3.) In the Administrative Tools window, double-click on the Computer Management
    (4.)  When Computer Management opens, click on Disk Management on the left side of the window, located under Storage. 
    (5.) This is where you will see Drives listed. The Card Reader will be listed as 1-4. Just right click & assign Drive Letter.
    Right click on each of the drives 1-4 and assign a Drive Letter. Now place your SD card in the correct slot and an a pop up for auto play will show. Now you reader works and will also show when you open COMPUTER it will show them as removable drives with proper drive letters. It took me several days to figure out after no help from HP or internet search. So when found the drives listed I just right clicked saw assign drive and it worked. Hope a lot of people searching on internet find this reply so that it will help them get there card reader working again under Windows 7 because even there tech's don't have an answer. Well good luck because this will work!!!

    owj wrote:
    I followed the steps but did not see drive 1, 2, 3, 4.  I see C; Jbackup drive, D: CD/DVD.  I'm still not able to get the card reader to recognize an inserted card.
    HP notebook 10''
    I'm having trouble with my card reader. I been thro steps mentioned in HP forum but only C:drive is listed .
    I had a problem with the hard drive earlier this year had to reinstall windows 7home premium from a disc unable to activate system restore.
    Ian Barrow

  • Problem with Decklink card during voice over

    Hi,
    i have PMG5 2.5 GHz with FCS & Blackmagic Decklink extreme card.
    all these days i had a great time working on FCP . till i faced a peculiar problem
    when i am capturing video from Beta or DV 50 , i am able to select video Only or Audio only , or Video & Audio .
    but when iam trying to capture Audio Only option through the the Mic which is connected to the mixer, i am not able to capture audio.
    even i have noticed one more strange thing, i have tried Voice Over tool in FCP 5.04 with Decklinik card and i am not able to grab any audio through the Decklink card.
    but i can use built in audio for my voiceover.
    has anybody come across this kind of problem,
    can somebody help me .

    Hi Rajendra,
    your questions is marked as solved, but I haven't seen your question answered, so I might be wasting time. Anyway.
    I bumped into the same problem not long ago. I'm using a Multibridge, but the problem and solution are the same. Here's the reply I got from Kristian Lam over at Blackmagic:
    In order to get vo tool in Final Cut Pro HD to work, these are the
    steps to follow:
    1) Video Input in Blackmagic DeckLink preferences is set to match the audio input type. For example, if you're recording via the XLR connectors of your card, then then 'Inputs' under 'DeckLink Video Connections' must set to analog. It doesn't matter if it's component or composite analog video.
    2) In the View menu of Final Cut Pro HD, set External Video to “Off”. When finished with the Voice Over tool, set External Video to “All Frames” to use the broadcast monitor.
    3) You must have a stable video signal going into the card when using the vo tool or Final Cut Pro HD will not see the audio. (or use a Blackburst generator)
    4) Use the Displays menu to set the DeckLink desktop to the same format as the video source, eg. NTSC 720 x 486.
    Well, then select your Decklink Card in the Voiceover Input selection. Even after I had done all that, I couldn't see any audio coming into FCP. The solution to that was to raise the Trim at the top of the mixer. I got a nice signal into the Mackie and voilà also sound into FCP.
    Hope this helps,
    Colin

  • Flex 14 SD card reader not working with larger cards on Windows 8.1

    The card reader in my Flex 14 is behaving very oddly. When I insert a 16GB SDHC card it makes the 'USB inserted' noise and the card shows up under device manager but I can't access it through file explorer. The card reader works fine with smaller SD cards that I have. I tried the card in another, Win7 laptop and it worked fine.
    I see a number of other people are having a similar problem and I have followed all of the troubleshooting advice I can find, but nothing is working. Does anyone have any other suggestions?
    This is what I have tried:
    1. Leaving the card in the camera and attaching the camera via USB cable to the laptop: same result, noise, but can't access the card.
    2. Trying to reassign the drive letter through storage controller: it shows the card but if you right click it to assign it a drive letter it says the 'file is missing'.
    3. Downloaded the Win8.1 x64 driver from Lenovo website and installed. This stopped the card being recognised at all.
    4. Installed the Win8 xc4 driver: this got me back to the noise but no action stage.
    5. Updated Windows.
    6. Uninstalled and reinstalled the driver numerous times both with the card inserted and without it and with restarting the computer after unistall and after reinstall.
    7. Ran Ubunutu from a live USB: This allowed me to see the card and copy its contents to the laptop's HDD.
    So it seems to be some incompatibility between the Lenovo drivers and Win8.1. Potentially it's to do with the USB drivers rather than the card reader drivers as the result when using the USB cable and the camera was the same as putting the card in the card reader. Is there a way to update these?
    Any other troubleshooting steps I could take?
    Thanks.

    What size are the cards?
    Another way. You can use a USB flash drive & the camera connection kit.
    Plug the USB flash drive (works the same with an SD card) into your computer & create a new folder titled DCIM. Then put your movie/photo files into the folder. The files must have a filename with exactly 8 characters long (no spaces) plus the file extension (i.e., my-movie.mov; DSCN0164.jpg).
    Now plug the flash drive into the iPad using the camera connection kit. Open the Photos app, the movie/photo files should appear & you can import. (You can not export using the camera connection kit.)
    Using The iPad Camera Connection Kit
    http://support.apple.com/kb/HT4101
    Secrets of the iPad Camera Connection Kit
    http://howto.cnet.com/8301-11310_39-57401068-285/secrets-of-the-ipad-camera-conn ection-kit/
     Cheers, Tom 

  • Problem with Display card of Probook 450 G1

    Hello
    I have just bought Hp probook 450 G1 and i have installed all mandatory drivers from HP site , but now i am facing a problem with the display cards .I tried it n PES 13 Game , it says that my device is not apprpraite  , also it reads the AMD card ram as 32 MB and says its unable , also that happens with intel card.

    Hello @Captiano ,
    Thanks for posting on the HP Forums!
    I understand you are experiencing an issue with your notebook. However, since this is a commercial notebook, you should post your issue on the notebook board of the HP Enterprise Forums for a better answer.
    Have a wonderful day!
    Mario
    I worked on behalf of HP.

  • 23" Cinema Display with DVI-ADC Adapter.  Won't turn on with 8800 card...

    I am running Windows XP on a pc. I have had the ACD 23" with the DVI to ADC adapter for 4 years now and it has been flawless. I ran this using an nVidia 6800 Ultra card and then an 8800 GTS 640 MB card. All was well. I just got a 2 new cards for 2 diferent pc's and neither will recognize or turn on the monitor. Both a brand new HD 2600 pro ATI card and an NVidia 8800 GTS 512 card. The monitor works fine with my 2 PC laptops via their DVI connections and my MBPro. So it appears the monitor is fine. This is not the "can't see the monitor in the bios" issue, I can't even use it as an additional monitor in dual view mode when at the desktop as it is not recognized as being connected. Any ideas?
    PS I also applied the latest bios update to the nVidia card from EVGA.
    Thanks,
    Reed

    Did anybody find a solution for this?
    I bought a new T420s. The second week I had to send it in service because it was not turning on anymore. I couldn't convince them that the laptop suddenly restarts several times a day. And only after two weeks when it did not start anymore they told me to send it in the service.
    No they brough it today. They made my day happy for 10 minutes until I turned it on and the wireless problem described in this topis apeared. The Inetl diagnostics tools installed with the card say: "Hardware radio is off". It worked before being send into the service.
    Now, the wireless switch is on and I see the adapter installed by "no wireless connections available".
    Pressing Fn-F5 it tells me to turn on the radio (the switch thing). But that is already turned on.
    So I called again to ask them what is wrong. They told me they would send me a new mini wireless card that I can replace myself. I received it today, replaced it. BUT THE SAME BEHAVIOR!!! (((((((((((((((((((((
    So I wonder, can the service guys (Wädenswil, CH) be so unprofessional to have forgotten to connect/enable the switch button?
    PS:
    1. The wireless LED is not turned on at all.
    2. BIOS has wireless enabled
    3. Device Manager sees the unknown network adapter (when driver uninstalled) and the Intel Wireless adapter (when driver installed)
    (This double failure means a divorce from Lenovo products for me. Once I solve this issue I sell the laptop.) Yes I know service is better than other, but I want something that doesn't need it at all.
    At least the Dell guys send a guy (freelancer service guy) at my place to fix the isssue. Now it is not only the costs for shiping it and investigate the problem (that are on my side) but also the productivity problem now costing us more than one month not beneffiting 1 minute from this laptop.
    A very sad,
    Gabriel

  • Loss 3D graphics and can't connect to external display with NVIDIA card

    I note this morning that the graphics in 3D mode of iWork (version 4.1 with system 10.6.8) no longer appears in all software suite. The 2D graphics are displayed perfectly. I also notice I can't connect an external display when I am on NVIDIA card but work well with Intel card.
    The 3D graphics are printed but not displayed on the screen (it also appear inthe thumbnail). It seems to be a worry to display.
    I posted two screen images showing the problem of 3D in Pages.
    Link :
    http://www.flickr.com/photos/94407289@N00/6105793305/
    and
    http://www.flickr.com/photos/94407289@N00/6106332902/
    What's going on? and can someone help me because I have a report?

    Hello lolthisnameisnttaken,
    Based on your post it seems you're having an issue with an external display. The following article may help you find a solution:
    Apple computers: Troubleshooting issues with video on internal or external displays - Apple Support
    Thank you for contributing to Apple Support Communities.
    Cheers,
    Bobby_D

  • Setting up two  iPod Touches on one account with gift cards for app and in-app purchases

    I have multiple devices on one account - 2 iPod classics, one iPhone 3G and two recently acquired iPod Touches for my 8 year old boys.  They want to make in-app purchases (for Dragonville).  They each have their own gamecenter ID.  I want to set up each of them with gift cards for their purchases.  Is this possible?
    If not, what is the recommended approach to manage all devices in one place while allowing individual devices to have a seperate payment mechanism?
    Thanks.

    I recommend that you
    Create a NEW account/ID for her using these instructions. Make sure you follow the instructions. Many do not and if you do not you will not get the None option. You must use an email address that you have not used with Apple before. Make sure you specify a birthdate that results in being at least 13 years old
      Creating an iTunes Store, App Store, iBookstore, and Mac App Store account without a credit card
    More details of how:
    http://ipadhelp.com/ipad-help-tips-tricks/how-to-get-free-apps-from-the-app-stor e-without-a-credit-card/
    Use the new ID on her iPod but only for:
    Settings>Messages>Send and Receive
    Settings>FaceTime
    Settings>GameCenter
    and Settings>iCloud if you want her to have separate Contacts Calendar and some other things.   
    Continue to use the same/common Apple ID for Settings>iTunes and App stores so you can share purchases.
    To make sure you only sync the media yoo want, configure iTunes syncing so that only checked media is synced to the idevices.
    iTunes: Syncing media content to iOS devices and iPod
    Also see:
    How to use multiple iPods, iPads, or iPhones with one computer

  • Just got an ipad air and while creating my apple ID with credit card, I got to itunes gift card/ itunes gift section and was asked to supply a CODE to proceed with the form but I don't have the code. please how how can i get the code?

    Just got an ipad air and why creating my apple ID with credit card, a CODE was requested in the itunes gift card/ itunes gift in order to preceed with the form but I don't have the code. Please how can I find the code so as to enable me complete the form successfully. Thanks alot

    The iTunes gift card field is optional, you don't have to fill it in - leave it blank if you don't have a gift card.
    iTunes gift cards are country-specific (they can only be used in their country of issue), and they are not available in all countries - so you might not be able to dill it anyway.

  • Can i upgrade my iCloud storage with itunes card ?

    Can i upgrade my iCloud storage with itunes card ?

    From what i understand, you want to buy more storage on iCloud using an iTunes card right?

  • Looking for a for an all-in-one printer that is compatible with greeting card programs..​.

    looking for a for an all-in-one printer that is compatible with greeting card programs...my original one was an HP PSC  1510...replaced it with a Deskjet 1050 & it does not work...any suggestions?

    I bought an epson xp650 a couple of months ago and cannot fault it. It does everything I require and it is the wifi model so I can print directly from my ipad/iphone. Not sure if you are asking about the colour of the unit or just to be able to print black and white, Obviously all printers will print black and white but just to give you a little more info the printer I bought is the white version and it looks really nice sat next to my imac 27''
    Hope this helps.

Maybe you are looking for