GB2 + M-Audio FastTrack USB + Bass

Hi,
I have a problem whereby using the above gives me a very low input into GB2. To clarify:
- Using GB2 with update in 10.9.3
- Using Amercian Precsision Bass so decent output from guitar with a new cablewaves guitar cable
- DI'd straight into FT USB
- FT USB input setting set to highhest
- Guitar/Line input set to guitar
- OS X and GB2 input levels set to high
Seems strange as this should have a reasonably decent signal. My strat has a higher inout level.
Anyone had this problem? Any ideas?
Thanks in advance,
Wayne

Since this behavior usually indicates an interruption in the communication between Audition and the audio driver, I wonder if a "force driver reload" button would help. I'm not sure if the application can automatically sense this state since there appears to be enough of a data stream to make it appear as if things are ok.
Either way, it's something that needs investigation.

Similar Messages

M-Audio FastTrack USB recording isn't working?

M-Audio FastTrack USB recording- I installed it, and am trying to record sound through my keyboard. I can hear the sound through my headphones, and Audition recognizes the device, ( I have the input set to Mono > Line In 1 FastTrack) but not the sound. The level bar won't move or anything. I have no clue why this isn't working and I've been messing with it for hours so I'd really appriciate some help!

Since this behavior usually indicates an interruption in the communication between Audition and the audio driver, I wonder if a "force driver reload" button would help. I'm not sure if the application can automatically sense this state since there appears to be enough of a data stream to make it appear as if things are ok.
Either way, it's something that needs investigation.

M-Audio FastTrack USB - very low signal level (line/guitar)

I've used FastTrack USB for a couple of years with a microphone through the XLR input with no problems. Now I am trying to connect a line output of a synthesizer to the line input of the FastTrack and the signal level is very low. There is no noise, it's just quiet, even with the track volume all the way up it's still no match for the rest of the tracks.
Any suggestions, except for trying all the knobs and switches on the face and back of the unit (tried that already)? Anybody has similar setup?
I use FastTrack for audio input, and built-in audio for output, it's connected through a hub (no problems for two years). In GB microphone is going to the Channel 1 (mono), and still works fine. Synthesizer goes to Channel 2 (mono) and is really quiet. I tried the syn with two different 1/4 cables with no difference. The headphones jack on the front of the FastTrack works fine with the normal level adjustment range, and if I plug in the headphones directly into the line out of my syn, I have sound, quiet (like you would get by connecting headphones to any line out, turntable even) but steady, so the syn must be fine.
Any thoughts?

No takers. Hm. OK. After some more research on the Net it appears to be that all the Fast Tracks suffer from the same problem, which makes me believe that it's not a bug, but a feature of an unexplainable kind. Oh, well, back to my old iMic noisemaker (this one works, it's just screened very poorly, so it picks up all the possible interference, and also makes its own little nasty hiss--this is why I switched to the Fast Track a while ago--so I will need to cut it out with an EQ, again). Hopefully, the EQ surgery will not affect the synthesizer's sound consistency as severely as it use to do with a microphone.

M-Audio FastTrack USB through GarageBand 2 Questions

Hi,
I am running the M-Audio Fast Track USB on my MAC
desktop (OS X 10.4.7 Tiger), through the MAC Garage
Band recording program. I am having a serious amount
of trouble getting this thing to work.
First: When I record a track through GT Player
Express onto Garage Band, it seems to be recording in
MONO. I have the Fast Track Set to stereo.
I am unable to hear the recorded instrument track
during playback.
When I switch the preferences to Built In Speaker to
hear the instrument track, I can hear it, but the Guitar Express
effect is gone.
Also. It doesn't seem like the FastTrack Module pushes very much sound...???
In a nut shell, I haven't been able to record a successful instrument track yet.
I would appreciate any suggestions/help. Thanks for your time!
Steven
IMac G5 Mac OS X (10.4.7) Tiger

I am also a recent purchaser of the m-audio fast track interface.
What's with this "plug and play" ? The Mac simply won't take in my 1/4 " input from my guitars (acoustic with a pickup & electric) through the USB connection. I've been tweaking it for the last 2 hours and seem to be getting nowhere in GarageBand. My "sound" pref setting are fine. Under prefs in GB it states 0 Midi input(s) detected. It hardly moves the sensor in the "sound" pref settings when I strum.
This is very frustrating! I had no problem connecting an old MIDI keyboard to GB with a very simple USB - MIDI device. Spent a bit more on this and no results!
I may just take it back. Do I need a pre amp? How much $? Is the separately powered firewire interface better???
Help Please!

I need HELP connecting a M-Audio FastTrack Pro USB with a Behringer 1202!!!

i need some assistance wireing up my personal studio. Im running on a Mac Pro Tower Logic 8. I have a M-Audio FastTrack Pro USB interface and want to hook up a Behringer 1202fx mixer. How exactly do i do the wiring for this???what settings do i need to change in system preferences or in Logic.????? PLEASE HELP ME!!!!!

It depends what you want to do, and what gear you are hooking up and what you want to do with it.
How you hook it up really depends on your needs, which you don't specify.

Problems with M-Audio Fasttrack Pro and Garageband after 10.5.2

Hi all,
I use GarageBand daily with my M-Audio FastTrack Pro and have had absolutely no problems until I installed the 10.5.2 update.
Suddenly the Audio randomly cuts out when I'm recording, monitoring or playing back - also my recordings appear to skip and jump too. Usually I can rectify it by power cycling the Fasttrack but the problem re-occurs after about 30 seconds of recording.
I have double checked the I am using M-Audio's latest drivers and have repaired permissions and the disk. I was wondering if anyone else had had any problems with this?
All help would be appreciated, looks like I'm going back to 10.5.1 though.

Hi !
Still no answer from M-Audio but it seems that they are not in cause.
I read on several topics of Apple's Forums some similar problems with other audio devices and also with some USBhubs.
I ran some little tests and for my case, using the other USB port of the MacBook seems to resolve the problem (but that's not a permanent solution for my point of view).
Using a selft-powered USBhub works also, even on the port that makes it crash without hub.
As I studied a little bit of electronics, it looks really like a problem of power supply through USB to me. It could be some kind of micro-cuts (or micro-undervoltage) that are sufficient to cut the audio stream and freeze a bit the system but not enough for MacOSX to switch significantly to the internal audio.
But two questions still remain :
Why one USB port of the MacBook and not the other one ?
Why since 10.5.2 ?
Steve, if you hear me ;o)
'Hope they will react quickly !

Latency and the M-Audio mobilpre USB

I know its like an overworked subject but I have searched and gotten no real answer.
small but realy annoying amount of latency makes doing overdubs and such a real confusing thing. (aka-beotch).
playback always lagging just a little behind new input(mic or instr).
I have an M-Audio mobilpre USB and am having unacceptable latency probs.
everything as suggested has been done.
GB-Mobilepre-up to latest rev-driver etc...
last try was all monitors off-only 1 track-optimized buffer for speed.
I have a 1.2gig pros-1.62gig ram on a g4.
could it be that its just the fact of USB as opposed to firewire?
any guesses?
thanx
cheers,
matt
g4-1.2gig proc-lots of HD and mem Mac OS X (10.3.8)
g4-1.2gig proc-lots of HD and mem Mac OS X (10.3.8)

"be you USB or be you fire wire"
I am using a simple setup:
Small unpowered mixer connected to my iBook via iMic. (USB 2 connection)
For MIDI: I have a Keystation 49e (direct USB) and a Yamaha PSR 520 connected via MIDIMAN usb 1x1.
I do not plug my headphones into the iMic because the latency was noticeable. I only use the iMic for input. I plug the headphones into my headphone jack and turn on monitoring in each track I am recording live. The latency is barely, barely noticeable.
You have an even better option via zero latency monitoring. If you can't get past the latency then you will have to monitor using the Mobile Pre. See your manual for details.
I believe my performance (including latency time) has improved since running the sessions from my firewire external drive. My drive is a Lacie 160GB, 7200rpm, 8M cache firewire drive. In addition to freeing up memory on the hardrive on my iBook, the faster spinning drive seems to boost my performance as well.
In a recent session a bass guitarist noticed annoying latency. I realized I had a cpu intensive plugin enabled. Turning the effect off removed the latency problem.
While running Garageband make sure no other tasks are running, such as indexing. File vault is also a performance killer and I finally turned it off.
More suggestions here:
GarageBand 2 Help: Optimizing GarageBand performance
Kurt

No audio after USB audio accessory is connected

I've discovered what I believe is a rather interesting (and rather serious) bug in the iPhone 2.0 software:
When an USB IAP accessory (such as a lot of newer car stereos) is connected and disconnected a couple of times the audio output from the iPhone will often stop working. Disconnecting the accessory or plugging/unplugging headphones does not fix the problem.
And I mean the audio completely dies: I get no audio from the phone, voicemail, ringtones, iPod, or system sounds from the speaker, headphones, or dock output.
It's like the audio drivers crash. Sometimes the audio will start working again after a long period of time (like if the phone has been sitting idle for hours while I'm at work) but usually I have to reboot to get it working. It seems when I can get audio to work again without a reboot, I get a new crashReporter log about mediaserverd the next time I sync.
The problem occurs when the phone is connected to an iPod accessory that uses the IAP audio-over-USB capability (I tried my Pioneer car stereo and a Kenwood stereo at Best Buy) It does not occur when connected to an accessory that only uses analog audio. I've seen it happen on my iPhone 3G and the original iPhone, so I know it's not a hardware problem.
I know for a fact the Pioneer and Kenwood units I tested are stated as having USB inputs compatible with the iPod Video, iPod Nano, iPod Classic, and iPod touch. (I can confirm the Pioneer does work fine with my old iPod Video.)
Multiple reviews have shown them to also work well with original iPhones running 1.1.4 and below (even if you do get the "not made for iPhone" warning)
However, both phones I tested are running 2.0. Which leads me to think this is a bad 2.0 bug.

moved to different forum

Sound plays through Matrox MX02 instead of Komplete Audio 6 USB Device =(

In Adobe Premire Pro CC I can't use my NI Komplete Audio 6 usb device for playback. Instead sound always comes out of my Matrox MX02 when I'm scrubbing or playing.
Under Preferences -> Audio Hardware -> Default Device I have selected Komplete Audio 6. When I hit ASIO settings it brings up the expected Komplete Audio 6 Control Panel.
Under Preferences -> Playback -> Audio Device I see options for Adobe DV, Adobe Desktop Audio, and Matrox Player but no Komplete Audio 6.
My system is a custom built Windows7 PC. Any advice on getting sound out of my Komplete Audio 6 instead of the Matrox MX02 would be much appreciated!

the komplete audio 6 seems more problematic than expected.
Preferences -> Audio Hardware -> Default Device -> Premiere Pro WDM Sound causes stuttery playback. I've tried enabling/disableing "Device 32-bit Playback" under ASIO settings and I've also ensured that the buffer size (256 samples) is the same as in my Komplete Audio 6 Control Panel.
Preferences -> Audio Hardware -> Default Device -> Komplete Audio 6 audio playback is fine but if I alt-tab away from PPCS6 the application will freeze as I describe in this thread: http://forums.adobe.com/message/5412540#5412540 ...
I'm running the latest driver/control pannel from Native Instruments (3.1.0) and the latest firmware has been flashed to the Komplete Audio 6 (45).

Can MacBook Pro output digital audio via usb?

I'd like to output digital audio via usb. Can it be done from iTunes? This would allow me to go directly to my dac and then to my preamp.
Thanks.

Russell, there are quite a variety of devices that accept digital audio over USB from any mac with a USB port - see http://www.trendsaudio.com/EN/Product/USBAudiodesc.htm for one example.
Try a google on MAC USB Audio OUTPUT any you should pop up some useful options.
Cheers
Rod
Message was edited by: Rod Hagen

Displayport audio vs USB audio

I have pre-Thunderbolt 27 display that is offering my 2011 Mac Mini 2 audio options : Display Port vs USB audio
Now, I beleive if I will have to plug in the USB cable either way, to ge the USB hub, microphone, camera to work.
So I don't believe I can necessarily save the USB port (if I could, then why would there be Thunderbolt?).
What I want to know is there any advantage to using Display Audio over USB ?
- Is the sound any better ?
- When I am using USB networking for other purposes, will Display Audio have less USB bus contention and play better ?
- Similar as above, when playing music over Display Port, will my USB devices be faster due to less contention ?
I am leaning towards Display Port audio unless someone can give a definitive answer
Thanks.

You say 'no', but then why did they add the option on the Mac Mini? ie It wasn't to free the USB connector, as that is still used anyhow for the camera, mic, usb hub and software updates.
Software updates? Not sure what that has to do with this. But anyhow I have a mac pro with a 27" mini-displayport apple display and both options are available too. It has nothing to do with power (I'm certainly not underpowered). It's simply that those ports are available audio out devices.
On my old Macbook Pro, when viewing live video from my Hauppagauge HDPVR via a different USB port on the Mac (not the screen), the sound was sometimes choppy if I was doing other tasks as well.
You machine has its limits in processing power and is probably having trouble using too many processor intensive processes. Use your Activity Monitor to see which processes are using large amounts of cpu time.
The display has a USB hub that chains of the USB port, so if have other devices working like my external USB Bluray drive, then I think there could be contention when using that also when reading/writing.
Contention is managed everywhere; hard drives, usb buss, fireware buss, pci buss, memory buss, and any others I can't think of at the moment. You're splitting hairs worrying about sending audio to usb ports which is a blip on the overall processing of generating that audio in the first place. In other words its the processes and efficiency of your machine that are a bootleneck.
So I am really hoping someone will confirm that the audio data was moved to the mini-display plug to provide more bandwidth via the USB controller, or to guarantee bandwidth for consistent audio.
Good luck with that.

Airport express & digital audio through usb

Can airport express stream digital audio through usb to use with a usb DAC?

No. Digital optical audio is only available via the AirPort Express' audio port only.

Can't hear sound with M-Audio MobilePre USB driver in Logic 7.2

Hi. I've installed an M-Audio MobilePre USB interface to hook up a nova mic and i've also hooked up an oxygen eight midi keyboard. Can't get any sound from Logic when i select M-Audio MobilePre USB as my driver, and can't get Logic to recognize my midi keyboard. I have downloaded the latest M-Audio MobilePre USB update off the web, and still nothing. I'm new at all of this. Can someone help me? Thanks in advance.

I'm wondering did you install the drivers and after that plugin the usb devices or did you leave them plugged in during install?
What happens when you unplug the midi interface and put it back in? Is it recognized by Logic by putting up a dialog that something has changed?

Plantronics .Audio 510 USB not detected in Leopard

Hi guys and gals
I just updated my OS X from 10.4.9 to 10.5.1, and now I've got a bit of a problem with my Plantronics .Audio 510 USB headset. In 10.4, it would be detected automatically and work just dandy, but in 10.5, no such luck. It will not even show up in Sound in the Pref Panel. I've checked that the USB headset is receiving power, and it is. The mute button works and lights up, and the volume buttons affect OS X. The volume is turned up or down when I press them, but for the built-in speakers only.
Any ideas?
Thanks in advance.

Hi guys,
I've just bought the .Audio 510 USB myself. My system sees the headset but only as an "Unkown USB Audio Device". I can get it working, but I need to manually go in and select it in my systems settings and Skype preferences each time I plug it in.
I also use NiceCast streaming software and it's the same deal with that. How are you guys getting on with it. Have you had any success since you last posted?

L505D-LS5001 no audio / no usb problem

i been having problems with my audio and usb drive, allready try installing drivers and nothing..
the audio tells me no audio output installed.
and the usb and sd card slot wont work eider. runnning windows 7 32bit , audio driver is microsoft audio highdefiniton with the yellow (!)
when i try to install laptops drivers go to the best drivers allready install.
usb problem i really dont know whats the problem..Laptop still on warranty.
Any help please

I have run into this same issue; it seems to occur that in device manager, no USB host is even present. Audio just has a red "X" on it.
I've tried installing the drivers, updates.
I restored from the Restore discs from Toshiba (which just crash)
I've done an install from a straight WIn7 X64 disc (which works, but then Red "X")
I've tried changing memory, HDD..
I've tried bootable LInux, which also doesn't see a USB controller.
This is very annoying. This seems to have happened after someone flashed the 1.10 BIOS onto this (I have an L505D-LS5007)
Something here is very amiss, and a laptop with no USB, no Audio is almost worthless. It's as though the BIOS control for the southbridge is wrong. I've tried re-flashing with 1.10, no difference.. I'd love to be able to rollback to 1.00, but I can't even find it.

GB2 + M-Audio FastTrack USB + Bass

Similar Messages

Maybe you are looking for