Gbic module for SGE2000

Hello, I need to know which gbic modules are compatible SGE2000P SGE2000 and if I can connect those with a switch that has a module SRW2008P with MGBSX1.

I found an old Linksys manual (attached) for the SGE2000/200P switches. The SFPs that the system supports are as follows:
"Use the Linksys MGBT1, MGBSX1, or MGBLH1 mini-GBIC modules
with the Switch. The MGBSX1 and the MGBLH1 require fiber cabling
with LC connectors, while the MGBT1 requires a Category 5e Ethernet
cable with an RJ-45 connector."
Shouldn't be any problem connecting the two switches via MGBSX1 interfaces.
Hope this helps!
Tom

Similar Messages

SRW2024 Mini-GBIC modules

I have a number of SRW2024 switches and several Mini-GBIC modules for them. Are these switches compatible with other brands of Mini-GBIC modules or do I need to use the Linksys modules (MGBSX1) only? Thanks!

LouisWu, did you find out if any of your other SFPs worked in the Linksys switch?
do you get any error messages when you insert a 3rd party SFP?

10Gig - GBIC module, can we connect?

Hi,
I have a PIX 535 firewall which has GBIC module and I need to connect to a Switch 2360 / 2960 which has 10 Gig SFP.
Can I connect using multimode fiber. Will it work?
Or is there any Speed configuration we can do to reduce 10 Gig to 1 Gig in the switch side?
Thanks & REgards,
Lenin. S
96207 45656

Hi I beleive the PIX interface is fixed at 1GigE and with a 10GE SFP in the switch this configuration won't work, you need to ensure the devices are matched for the same speed and media type Multi Mode (MM) or Single Mode (SM).
I beleive the PIX GE interface is MM so you will need to install an MM 1GE SFP into the switch don't forget that you will also need a GigE Failover Link if you are using PIX Failover.
Chris

Optical Fiber connection between GBIC module and SFP module

Hi
I am in need of help.
I have a 3750 24TS-S, 2 port SFP, switch at the edge. And i have a 4507R switch at the Distribution layer. In 4507 switch I have WS-X4515 Sup IV supervisor engine with 2 GBIC Port and also have WS-4306-GB 6 port GBIC module. I am using WS-G5486 Single mode connector, LX/LH tranceiver to connect to this port.
This is the scenario.. i want to know is it posible to conect one end of the fiber cable to connect to a SFP Module ( 3750-24TS-S, 2 Port SFP) and other end ( WS-X4515 Sup IV supervisor engine with 2 GBIC Port or WS-4306-GB 6 port GBIC module) at the WS-G5486 Single mode LX/LH connector ?????
Plz let me now asap.. i need to give a solution imdtly.
Thanks & regards
Jacob

Discussion is never a problem ....;-}
The issue is that the signal is "too loud" and is distorted (or, more correctly, is so loud it overloads the receiver).
The operational envelope for nearly every receiver of any kind includes a bottom number (too weak to hear) and a top number (too loud to understand).
As an example, think about an system where you have a hearing aid that would let you hear someone speaking in a normal voice from 100 feet away ... then having someone scream the same words into the hearing aid from 6 inches away ... the sound would be distorted and you would have difficulty understanding them ... after a while, you'd begein to go deaf and eventually, it would sound normal (until you became completely deaf).
So, what you need to do is look at the transmitter power, and the envelope/range of acceptable power the receiver can hear.
Normally that difference is the optical budget ... given the loss numbers of the media between the two, you can determine if you have enough power to make the trip.
In a Lab environment, you still have to hit the receiver's budget number, but from the other end (the "too high" side).
If you know the transmitter puts out X, and the receiver can accept from Y to (X-50), then you need to add enough attenuation to get X down to (X-50)or lower (but still more than Y).
When you have a transmitter powerful enough to drive tens of kilometers, putting one two meters away from the receiver will pretty much guarantee a burnout (unless you install optical attenuation).
Good Luck
Scott

GBIC Modules compatibility

Hello everyone,
I got a network with Siemens Scalance XR300M switches, and I got to do an optical connection to a Catalyst 3750 (3750G-24TS-1U).
The Siemens has a Gigabit Interface with SC Ports over SMF@1310nm (10 km module).
Which GBIC module should I use to connect both of them?
I looked at cisco.com and I saw only one SFP@1310 GBIC module (GLC-EX-SMD). But it is for longer distances!! (I suppose that a SMF@1300nm module will not be compatible with the SMF@1310nm in the Siemens Switch, right?)
Thanks in advance for your help!
Best regards,
Fabio

viyuan700 is correct is what he says.
The Cisco GLC-LH-SM transceiver will interface with your Siemen's Gigabit Ethernet 10km SMF interface. The actual IEEE 802.3 spec for Gigabit Ethernet 1000BASE-LX outlines a transmit and receive wavelength range of 1270 to 1355 nm; which covers both 1300 and 1310nm. Look at Section 38.4 - PMD to MDI optical specifications for 1000BASE-LX for the specifications.
The data sheet posted on Cisco's website (link below) indicates the GLC-LH-SM= is 1310nm.
Cisco Gigabit Ethernet SFP Data Sheet
<http://www.cisco.com/en/US/prod/collateral/modules/ps5455/ps6577/product_data_sheet0900aecd8033f885.html>
Sometimes vendors used 1300nm as a designation for MMF interface and 1310nm for SMF. Probably a reason but I don't know why.
I hope this helps! Let us know if you have any other questions.
Tom

Memory modules for Msi Big Bang trinergy

Hey forum,
i want to buy some memory modules for my trinergy mobo because the ones i had earlier also proved to be incompatible. I would like to ask you if there are any memory modules besides the ones recommended from the MSI site concerning my mobo. I am looking for a 2x2 gb ram kit with a heat dispenser so it can work around 1600mHz. Thank you in advance
P.S Is the list on the site the only one? i mean are there any updated versions of it with more high end memory modules tested?

Ideally you would provide us with your fullsystem specs first >>Posting Guide<<
From a memory perspective, the reason these modules have heatspreaders is mostly due to marketing and to impress the potential buyers. The secondary reason is that most manufacturers sell you overvolted and overclocked 1066 or 1333 chips on a 1600 marketed module that needs 1,65V instead of the standard 1,5V. Your memory controller is part of the CPU and natively only supports 1333 at 1,5V.
If you really insist, then at least get yourself a 1600 kit that does this speed at 1,5V. One of the modules that seem to work well are the CMZ4GX3M2A1600C9 from Corsair. From a user perspective, the mem modules from Crucial that you see in my signature come highly recommended as they have been proven to work on the P55 platform whenever used.

Functional module for automatic creation of pur requisition & pur order

hello,
what is the functional module for automatic creation of puchase requisition and automatic creation of purchase order which we will assign in action box in service order processing management.
please let me know as early as possible
regards,
rajesh kumar raju

Hi,
Please check with following.
IDOC_INPUT_ACC_PURCHASE_REQUI
IDOC_INPUT_ACC_PURCHASE_ORDER
/ISDFPS/OR_PURCHASE_ORDER_CR
BS01_PURCHASE_DOCUMENT_CREATE
CO_MP_CREATE_PURCHASE_ORDER
Thanks & Regards
Sadhu Kishore

Function module for calculating planned and actual cost of production order

Hi ,
Do we have any standard function module for calculating planned and actual cost for production order?
i need to implement this in a Z-report.
Thanks
Srini

Hi,
try below function module
CRMCO_GET_PLAN_ACTUAL_COSTS
CO_IH_GET_PLANNED_COSTS_TOTAL
Regards,
Sankaran

How to create the INBOUND Function Module for INBOUND IDOCs

Hi Friends,
Can any Suggest me How to proceed to Create an INBOUND Function Module for Processing the INBOUND IDOCS
which are recieved from XI Server ?
I am working in SAP-ISU
Here i will recieve the INBOUND IDOCs for the Meter Reading Orders.
We have a Standard INBOUND FUNCTION MODULE
IDOC_INPUT_ISU_MR_UPLOAD
which Uploads the Meter Reading Results.
I copied the Same function Module into ZIDOC_INPUT_
and working on it.
Can any one suggest me, whether i am going in correct way or not.
In IDOC_INPUT_ISU_MR_UPLOAD Inbound fun module,
BAPI_MTRREADDOC_UPLOAD is used to Update or Insert the Meter Reading Results,
My requirment is to Insert and Update the Meter Reading Orders which are Inbounded from XI.
Can I Use the Same BAPI
BAPI_MTRREADDOC_UPLOAD
to Update the below fields,
EABL-SERNR
EABL-ZWNUMMER
EABLG-ABLESGR
EABL-V_ZWSTAND
EABL-N_ZWSTAND
EABL-ABLHINW
EABL-ZSKIPC
EABL-ADAT
EABL-ATIMTATS
EABL-ADATTATS
EABL-ATIM
EABL-ZMESSAGE
EABL-ABLESER(Meter reader number)
Kindly Suggest me,
Thanks in Advance,
Ganesh

Hello Ganesh
I think you are going completely astray with you z-function module for IDoc processing.
If you look at TABLES parameter METERREADINGRESULTS (type BAPIEABLU ) of BAPI_MTRREADDOC_UPLOAD you will find many of the requested fields already:
EABL-SERNR => BAPIEABLU-SERIALNO
EABL-ZWNUMMER =>REGISTER
EABLG-ABLESGR
EABL-V_ZWSTAND
EABL-N_ZWSTAND
EABL-ABLHINW
EABL-ZSKIPC
EABL-ADAT
EABL-ATIMTATS => ACTUALMRTIME
EABL-ADATTATS => ACTUALMRDATE
EABL-ATIM
EABL-ZMESSAGE
EABL-ABLESER(Meter reader number)
Field EABL-ZMESSAGE appears to be custom field (at least I cannot find it on ECC 6.0). If this field was added using include CI_EABL then you probably can get these values into the BAPI using the EXTENSIONIN parameter.
Check routine CHECK_UPLOADRECORDS in the BAPI which allows two extension structures:
- BAPI_TE_EABL
- BAPI_TE_EOSB
Not surprisingly BAPI_TE_EABL contains the include CI_EABL.
Regards
Uwe

How to config Check Digits function module for Student Number Validation

Hi SLCM Experts,
In the SAP-SLCM, How to use check digits function module for validate student number. Just only config it or need to customizing program.
*Any idea to student number validation in SLCM?*
Best Regards,
Suvatchai K.

Hi ,
Can you expalin it further ?
You configure the St. no in piq_matr . And set it as external or internal no. range which suits your business .
What is the validation you are looking for ?
Regards
Gajalakshmi

Function Module for FB01 Vendor line items postings in 3.1 Version

Hello all,
Is there any Function Module for FB01 Vendor line items postings in 3.1 Version. I do not want to go for BDC. Please suggest.
Thanks,
Subba

Hi,
search for function module ACCPOSTING* or get development class of transaction FB01 and goto SE80, enter development class - and search in function group's function module.
Cheers.
...Reward if useful.

Function Modules for uploading the file

Hi experts ,
I have a requirement to download a file (csv) from my local sytem (say desktop) into an internal table first and then update the contents of the same internal table into the database table.
Can anybody provide me with a sample program for doing the same or at least the name of function modules for the same.
Prompt replies will be rewarded.
TIA
Abhishek

Hi Abhishek,
How to use INSERT Statement..
Check this Sample Program..
TABLES:MARA.
DATA:ITAB LIKE MARA OCCURS 0 WITH HEADER LINE.
START-OF-SELECTION.
ITAB-MATNR = '123ABCDA'. .
ITAB-MBRSH = 'C'.
ITAB-MTART = 'FERT' .
ITAB-MEINS = 'KG' .
APPEND ITAB.
ITAB-MATNR = '123ABCDB'. .
ITAB-MBRSH = 'C'.
ITAB-MTART = 'FERT' .
ITAB-MEINS = 'KG' .
APPEND ITAB.
LOOP AT ITAB.
INSERT MARA FROM ITAB.
MODIFY MARA .
ENDLOOP.

Function modules for the following

Hi,
I want to know the function modules for the following purposes.
1) Check whether a date is valid or not
2) Calculate the no of days between two dates.
Expecting an early response.
Thanks n Regards,
Amit

Hi,
PARAMETERS: p_list LIKE t009b-bumon AS LISTBOX
 VISIBLE LENGTH 11 OBLIGATORY ,
 p_list1 LIKE t009b-bdatj OBLIGATORY.
SELECTION-SCREEN POSITION POS_HIGH.
PARAMETERS: p_list2 LIKE t009b-bumon AS LISTBOX
 VISIBLE LENGTH 11 OBLIGATORY,
 p_list3 LIKE t009b-bdatj OBLIGATORY.
Calling Function Module for calculating no of days between the
selected period
 CALL FUNCTION 'NUMBER_OF_DAYS_PER_MONTH_GET'
 EXPORTING
 par_month = p_list
 par_year = p_list1
 IMPORTING
 par_days = ws_n_days.
 CALL FUNCTION 'NUMBER_OF_DAYS_PER_MONTH_GET'
 EXPORTING
 par_month = p_list2
 par_year = p_list3
 IMPORTING
 par_days = ws_n_days1.
For Concatenating the month and year into the date format
 CONCATENATE p_list1 p_list ws_i INTO ws_c_date1.
 CONCATENATE p_list3 p_list2 ws_n_days1 INTO ws_c_date2.
date = ws_c_date1 - ws_c_date2.
In the above sample code the selection screen has month and year as input.
Also check this link
http://www.sapdevelopment.co.uk/tips/date/datehome.htm
Check FM
RP_CALC_DATE_IN_INTERVAL Add/subtract years/months/days from a date
SD_DATETIME_DIFFERENCE Give the difference in Days and Time for 2 dates
Also for checking valid date:
U can specify the date field as
Select-options: s_date like likp-date(similar to ur requirement)
This itself ceck for the valid date no seperate validation needed.
Thanks & Regards,
Judith.

Function Modules for Data and Time

Hi all,
I need 2 function modules for date and time. when we pass current data(sy-datum) and current time (sy-uzeit) into function modules, shoud get date in dd/mm/yyyy or dd.mm.yyyy and time in HH:MM:SS formats.
Thanks in advance

Hi Ranjith,
i think this will b usefull for you..
SAP Bar Chart Function Modules and what they are used for
Function module
Used for
BARC_GRAPHIC_PBO
Starting bar chart at PBO time, using a graphic profile (parameter PROFILE)
BARC_GRAPHIC_PAI
Analyzing data returned by the graphic
BARC_SET_TIME_AXIS
Setting start and end of time axis
BARC_SET_OPTIONS
Setting options
BARC_ADD_CHART
Creating a chart
BARC_SET_CHART_ATTRIB
Setting chart attributes
BARC_ADD_SECTION
Creating a section on the time axis
BARC_SET_SECTION_ATTRIB
Setting section attributes
BARC_ADD_RIBBON
Adding a ribbon to the time axis
BARC_SET_RIBBON_ATTRIB
Setting attributes for ribbons in the chart
BARC_ADD_GRID
Adding a time grid
BARC_SET_GRID_ATTRIB
Setting grid attributes
BARC_ADD_LAYER
Adding a layer (graphic elements)
BARC_SET_LAYER_ATTRIB
Setting layer attributes
BARC_ADD_LINE
Adding a line
BARC_ADD_CALENDAR
Creating a calendar
BARC_SET_CALENDAR_ATTRIB
Setting attributes for a calendar
BARC_ADD_TIME_PROFILE
Creating time profiles
BARC_SET_TIME_PROFILE_ATTRIB
Setting attributes for time profile
BARC_ADD_INTERVAL
Adding a time interval
BARC_SET_INTERVAL_ATTRIB
Setting time interval attributes
BARC_ADD_TIME_OBJECT
Creating a time object
BARC_CONVERT_DATE
Creating a date string in bar chart format
BARC_REVERT_DATE
Converting a date string in bar chart format to date and time
BARC_ADD_DATELINE
Creating a date line
BARC_SET_DATELINE_ATTRIB
Setting dateline attributes
BARC_GET_PROFILE_CONTENTS
Obtaining profile contents for customizing a chart
BARC_GET_COLUMN_WIDTH
Selecting new column width
BARC_SET_COLUMN_WIDTH
Setting the column width
BARC_GET_TEXTINDEX
Obtaining the text index of a field
BARC_SET_LABELS
Positioning the chart display
BARC_SET_COLUMN_ATTRIB
Setting column attributes
BARC_SET_ROW_ATTRIB
Setting row attributes
BARC_SET_ROW_HEIGHT
Setting the line height
BARC_SET_MAXCHARTS
Setting the maximum number of charts sent
If its usefull reward points

Function Module for open Purchase Order & Sales Order?

Hi, commonly I read the data from tables and calculate the open quantity for sales order and purchase order, but I want to know, are there any standard function modules for getting the list of open "purchase order" and "sales order" respectively?
Thanks and Regards.

hi Ren,
u can check all these bapi's related to salesorder
BAPI_SALESORDER_CHANGE Sales order: Change Sales Order
BAPI_SALESORDER_CONFIRMDELVRY Sales Order: Confirmation of Delivery; Document Flow Update
BAPI_SALESORDER_CREATEFROMDAT1 Sales order: Create Sales Order
BAPI_SALESORDER_CREATEFROMDAT2 Sales order: Create Sales Order
BAPI_SALESORDER_CREATEFROMDATA Create Sales Order, No More Maintenance
BAPI_SALESORDER_GETLIST Sales order: List of all Orders for Customer
BAPI_SALESORDER_GETSTATUS Sales Order: Display Status
BAPI_SALESORDER_SIMULATE Sales Order: Simulate Sales Order
May be this FM can help you
MB_ADD_PURCHASE_ORDER_QUANTITY (Reading and adding open purchase order quantities)
Regards,
Naveen

Gbic module for SGE2000

Similar Messages

Maybe you are looking for