Geforce 210 + windows 8.1 = death ?
Estimate HP team:
Im facing a very rare problem with my video card
My computer is this:
http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c03517270
windows 8.1
and my video card is this:
http://www.gigabyte.com/products/product-page.aspx?pid=3913#sp
( now there is not one drive installed from NVIDIA )
is not the first time I‘ve installing this video card, now the difference is I reset the pc as fabric conditions.
The last time the problem was update the driver; but now the pc don’t want to even start when I install the video card.
Is not totally death, I can see the lights, all the sounds BUT DON’T SHOW ANYTHING ON SCREEN.
If I unplug the video card all pc start normally without any problem.
I know is a very problematic video card but has been working normal until I reset the pc
This video card has been installed from +/- February 2013
Hope for any help
Kind Regards
Hi:
You need to disable secure boot and enable legacy mode when you install a video card on a PC that originally came with W8.
If you reset the BIOS to its defaults, it has renabled secure boot and disabled legacy mode.
Please see this link for more information.
http://support.hp.com/us-en/document/c03653200
Similar Messages
-
Problems with Nvidia GeForce 210 and windows 8.1
Hi all, I have Windows 8.1 Pro update 1 64bit installed, two weeks ago I started giving problems graphics card NVidia (even has me
given several blue screen).
I tried to update the drivers for the card but I got the same problem. It was working properly with generic
drivers, and if I went to Computer Administrator me a yellow triangle appeared
on my graphics card and the properties told me the following:
Windows has stopped this device because it has reported problems.
(Code 43 )
My machine is as follows:
Mainboard : Asus P5K SE
Chipset: Intel P31/P35
Processor : Intel Core 2 Quad Q6600 @ 2400MHz
Physical Memory : 3072MB (3 x 1024 DDR2- SDRAM)
Video Card : NVIDIA GeForce 8500 GT
Hard Disk : Seagate ST3320620AS ATA Device (320GB )
Monitor Type: LG Electronics L1919S
I just formatted
the computer from scratch, and
I still had the same problem with the graphics card,
so I imagined it would be a hardware problem
and bought NVIDIA GeForce 210.
In the end I
upgraded to Windows 8.1 update 1 with
the latest drivers for the GeForce 210,
and after 6 days running everything correctly, a few days ago
returned to give me problems,
the screen sometimes freezes and will not
let me do anything and after a while
giving me a blue screen and reboots
me, I suspect that the graphics drivers
are giving me problems, and I had to
disable the graphics card and work with
generic drivers from Microsoft, and even then I
was restarted once.
I installed Driver Booster and all the drivers are updated.
Could
anyone analyze
dump files dmp ? Download here
I got another dmp:
C:\Windows\MEMORY.DMP but it is too heavy.
Thanksyes, I check the dump files
this cause by graphic card, on which graphic card you reformat your PC and update
.NET framework maybe cause this driver corrupted
my suggestion is try using internal graphic card, just for testing
Just in case you don't believe me, please check this dump file
* Bugcheck Analysis *
Use !analyze -v to get detailed debugging information.
BugCheck 116, {ffffe000d84c4010, fffff800b540be2c, ffffffffc000009a, 4}
Unable to load image \SystemRoot\system32\DRIVERS\nvlddmkm.sys, Win32 error 0n2
*** WARNING: Unable to verify timestamp for nvlddmkm.sys
*** ERROR: Module load completed but symbols could not be loaded for nvlddmkm.sys
Probably caused by : nvlddmkm.sys ( nvlddmkm+9bbe2c )
Followup: MachineOwner
1: kd> !analyze -v
* Bugcheck Analysis *
VIDEO_TDR_FAILURE (116)
Attempt to reset the display driver and recover from timeout failed.
Arguments:
Arg1: ffffe000d84c4010, Optional pointer to internal TDR recovery context (TDR_RECOVERY_CONTEXT).
Arg2: fffff800b540be2c, The pointer into responsible device driver module (e.g. owner tag).
Arg3: ffffffffc000009a, Optional error code (NTSTATUS) of the last failed operation.
Arg4: 0000000000000004, Optional internal context dependent data.
Debugging Details:
FAULTING_IP:
nvlddmkm+9bbe2c
fffff800`b540be2c 803db68aeeff00 cmp byte ptr [nvlddmkm+0x8a48e9 (fffff800`b52f48e9)],0
DEFAULT_BUCKET_ID: GRAPHICS_DRIVER_TDR_FAULT
CUSTOMER_CRASH_COUNT: 1
BUGCHECK_STR: 0x116
PROCESS_NAME: System
CURRENT_IRQL: 0
ANALYSIS_VERSION: 6.3.9600.16384 (debuggers(dbg).130821-1623) amd64fre
STACK_TEXT:
ffffd000`8adadbb8 fffff800`b457bfac : 00000000`00000116 ffffe000`d84c4010 fffff800`b540be2c ffffffff`c000009a : nt!KeBugCheckEx
ffffd000`8adadbc0 fffff800`b457008d : fffff800`b540be2c ffffe000`d760b7f0 ffffe000`d84c4010 00000000`00000001 : dxgkrnl!TdrBugcheckOnTimeout+0xec
ffffd000`8adadc00 fffff800`b4570582 : ffffe000`d760f540 ffffd000`8adadc60 00000000`00000002 00000000`00000001 : dxgkrnl!ADAPTER_RENDER::Reset+0x1f5
ffffd000`8adadc30 fffff800`b457b919 : ffffd000`8ada01b0 00000000`00000000 ffffe000`d5ff91a0 ffffe000`d742b000 : dxgkrnl!DXGADAPTER::Reset+0x416
ffffd000`8adadca0 fffff800`b446cfde : fffff800`b4453c90 ffffe000`d742b000 fffff802`84c1c000 00000000`00000000 : dxgkrnl!TdrResetFromTimeout+0x15
ffffd000`8adadcd0 fffff800`b4453d1d : ffffe000`d742b000 00000000`00000080 ffffe000`d50b4500 ffffe000`00000000 : dxgmms1!VidSchiRecoverFromTDR+0x1a
ffffd000`8adadd00 fffff802`84ceb794 : fffff802`84f69a00 ffffe000`d50b4500 ffffd000`8adaddd0 fffff802`84d7337d : dxgmms1!VidSchiWorkerThread+0x8d
ffffd000`8adadd40 fffff802`84d765c6 : fffff802`84f02180 ffffe000`d50b4500 fffff802`84f69a00 00000000`00000000 : nt!PspSystemThreadStartup+0x58
ffffd000`8adadda0 00000000`00000000 : ffffd000`8adae000 ffffd000`8ada8000 00000000`00000000 00000000`00000000 : nt!KiStartSystemThread+0x16
STACK_COMMAND: .bugcheck ; kb
FOLLOWUP_IP:
nvlddmkm+9bbe2c
fffff800`b540be2c 803db68aeeff00 cmp byte ptr [nvlddmkm+0x8a48e9 (fffff800`b52f48e9)],0
SYMBOL_NAME: nvlddmkm+9bbe2c
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: nvlddmkm
IMAGE_NAME: nvlddmkm.sys
DEBUG_FLR_IMAGE_TIMESTAMP: 5315b408
FAILURE_BUCKET_ID: 0x116_IMAGE_nvlddmkm.sys
BUCKET_ID: 0x116_IMAGE_nvlddmkm.sys
ANALYSIS_SOURCE: KM
FAILURE_ID_HASH_STRING: km:0x116_image_nvlddmkm.sys
FAILURE_ID_HASH: {c89bfe8c-ed39-f658-ef27-f2898997fdbd}
Followup: MachineOwner
1: kd> lmvm nvlddmkm
start end module name
fffff800`b4a50000 fffff800`b56a8000 nvlddmkm T (no symbols)
Loaded symbol image file: nvlddmkm.sys
Image path: \SystemRoot\system32\DRIVERS\nvlddmkm.sys
Image name: nvlddmkm.sys
Timestamp: Tue Mar 04 19:07:52 2014 (5315B408)
CheckSum: 00C20523
ImageSize: 00C58000
Translations: 0000.04b0 0000.04e4 0409.04b0 0409.04e4 -
[SOLVED] Xorg freeze with nvidia GeForce 210 when resizing terminal
Hello,
I am working on Archlinux. My computer freeze when I resize a terminal window.
To reproduce the problem, I follow the below steps :
1- launch openbox (with tint2, xcompmgr and nitrogen)
2- start the "terminal" console emulator (with true transparent background)
3- launch opera and go to a website which take a while to load (with a lot of data) (I used http://www.lemonde.fr)
4- while the website is loading, switch to the terminal window and double click on the title bar to maximize it
5- the box freeze
I am not able to take the control back. I cannot exit or kill Xorg / Openbox. I cannot switch to a text terminal (ttyx). No key sequence is working.
Only a hard reset of the box is working.
I have tried to disable the transparent background of the terminal window without success.
I have tried to not start xcompmgr without success.
The problem also occurs with rxvt-unicode instead of terminal.
It seems the problem happens more often when using console emulator based on vte.
vte itself has the same issue.
The only workaround I have found is to disable the harware acceleration with the below parameter in the xorg.conf file:
Option "RenderAccel" "true"
The problem with this workaround are poor graphical performances.
Could you please let me know if you have any idea / clue to identify / fix this problem ?
Thanks and regards
uname -a
Linux myhost 2.6.38-ARCH #1 SMP PREEMPT Fri Apr 22 17:48:36 UTC 2011 i686 Intel(R) Core(TM)2 Duo CPU E7600 @ 3.06GHz GenuineIntel GNU/Linux
versions
nvidia 270.41.06-1
nvidia-utils 270.41.06-1
kernel26 2.6.38.4-1
openbox 3.4.11.2-2
xcompmgr 1.1.5-1
.xinitrc
#!/bin/sh
# ~/.xinitrc
# Executed by startx (run your window manager from here)
if [ -d /etc/X11/xinit/xinitrc.d ]; then
for f in /etc/X11/xinit/xinitrc.d/*; do
[ -x "$f" ] && . "$f"
done
unset f
fi
# exec gnome-session
# exec startkde
# exec startxfce4
# ...or the Window Manager of your choice
exec ck-launch-session openbox-session
.config/openbox/autostart.sh
# This shell script is run before Openbox launches.
# Environment variables set here are passed to the Openbox session.
# Set a background color
BG=""
if which hsetroot >/dev/null 2>&1; then
BG=hsetroot
else
if which esetroot >/dev/null 2>&1; then
BG=esetroot
else
if which xsetroot >/dev/null 2>&1; then
BG=xsetroot
fi
fi
fi
test -z $BG || $BG -solid "#303030"
# D-bus
if which dbus-launch >/dev/null 2>&1 && test -z "$DBUS_SESSION_BUS_ADDRESS"; then
eval `dbus-launch --sh-syntax --exit-with-session`
fi
# Make GTK apps look and behave how they were set up in the gnome config tools
if test -x /usr/libexec/gnome-settings-daemon >/dev/null; then
/usr/libexec/gnome-settings-daemon &
elif which gnome-settings-daemon >/dev/null 2>&1; then
gnome-settings-daemon &
# Make GTK apps look and behave how they were set up in the XFCE config tools
elif which xfce-mcs-manager >/dev/null 2>&1; then
xfce-mcs-manager n &
fi
# Preload stuff for KDE apps
if which start_kdeinit >/dev/null 2>&1; then
LD_BIND_NOW=true start_kdeinit --new-startup +kcminit_startup &
fi
# Run XDG autostart things. By default don't run anything desktop-specific
# See xdg-autostart --help more info
DESKTOP_ENV="OPENBOX"
if which /usr/lib/openbox/xdg-autostart >/dev/null 2>&1; then
/usr/lib/openbox/xdg-autostart $DESKTOP_ENV
fi
xcompmgr &
nitrogen --set-zoom-fill /mnt/data/pictures/flower.jpg &
tint2 &
xorg.conf
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc/"
FontPath "/usr/share/fonts/TTF/"
FontPath "/usr/share/fonts/OTF/"
FontPath "/usr/share/fonts/Type1/"
FontPath "/usr/share/fonts/100dpi/"
FontPath "/usr/share/fonts/75dpi/"
EndSection
Section "Module"
Load "extmod"
Load "glx"
Load "record"
Load "dbe"
Load "dri2"
EndSection
Section "InputClass"
Identifier "Keyboard Defaults"
MatchIsKeyboard "yes"
Option "XkbLayout" "fr"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Monitor Vendor"
ModelName "Monitor Model"
EndSection
Section "Device"
Identifier "Card0"
Driver "nvidia"
Option "RenderAccel" "true"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
SubSection "Display"
Viewport 0 0
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "Extensions"
Option "Composite" "Enable"
EndSection
Xorg.0.log
[ 485.566]
X.Org X Server 1.10.1
Release Date: 2011-04-15
[ 485.566] X Protocol Version 11, Revision 0
[ 485.566] Build Operating System: Linux 2.6.38-ARCH i686
[ 485.566] Current Operating System: Linux myhost 2.6.38-ARCH #1 SMP PREEMPT Fri Apr 22 17:48:36 UTC 2011 i686
[ 485.566] Kernel command line: root=/dev/sda3 ro
[ 485.566] Build Date: 16 April 2011 12:05:35PM
[ 485.566]
[ 485.566] Current version of pixman: 0.20.2
[ 485.567] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 485.567] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 485.567] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Apr 27 20:00:28 2011
[ 485.567] (==) Using config file: "/etc/X11/xorg.conf"
[ 485.568] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 485.568] (==) ServerLayout "X.org Configured"
[ 485.568] (**) |-->Screen "Screen0" (0)
[ 485.568] (**) | |-->Monitor "Monitor0"
[ 485.568] (**) | |-->Device "Card0"
[ 485.568] (**) |-->Input Device "Mouse0"
[ 485.568] (**) |-->Input Device "Keyboard0"
[ 485.568] (==) Automatically adding devices
[ 485.568] (==) Automatically enabling devices
[ 485.568] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 485.568] Entry deleted from font path.
[ 485.568] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 485.568] Entry deleted from font path.
[ 485.568] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 485.568] Entry deleted from font path.
[ 485.568] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 485.568] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 485.568] Entry deleted from font path.
[ 485.568] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 485.568] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 485.568] Entry deleted from font path.
[ 485.568] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 485.568] Entry deleted from font path.
[ 485.568] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 485.568] Entry deleted from font path.
[ 485.568] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 485.568] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 485.568] Entry deleted from font path.
[ 485.568] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 485.568] (**) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/
[ 485.568] (**) ModulePath set to "/usr/lib/xorg/modules"
[ 485.568] (**) Extension "Composite" is enabled
[ 485.568] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
[ 485.568] (WW) Disabling Mouse0
[ 485.568] (WW) Disabling Keyboard0
[ 485.568] (II) Loader magic: 0x81f4ee0
[ 485.568] (II) Module ABI versions:
[ 485.568] X.Org ANSI C Emulation: 0.4
[ 485.568] X.Org Video Driver: 10.0
[ 485.568] X.Org XInput driver : 12.2
[ 485.568] X.Org Server Extension : 5.0
[ 485.569] (--) PCI:*(0:1:0:0) 10de:0a65:1043:8334 rev 162, Mem @ 0xfa000000/16777216, 0xd0000000/268435456, 0xce000000/33554432, I/O @ 0x0000bc00/128, BIOS @ 0x????????/524288
[ 485.569] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 485.569] (II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
[ 485.569] (II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
[ 485.569] (II) "glx" will be loaded. This was enabled by default and also specified in the config file.
[ 485.569] (II) "record" will be loaded. This was enabled by default and also specified in the config file.
[ 485.569] (II) "dri" will be loaded by default.
[ 485.569] (II) "dri2" will be loaded. This was enabled by default and also specified in the config file.
[ 485.569] (II) LoadModule: "extmod"
[ 485.569] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 485.569] (II) Module extmod: vendor="X.Org Foundation"
[ 485.569] compiled for 1.10.1, module version = 1.0.0
[ 485.569] Module class: X.Org Server Extension
[ 485.569] ABI class: X.Org Server Extension, version 5.0
[ 485.569] (II) Loading extension MIT-SCREEN-SAVER
[ 485.569] (II) Loading extension XFree86-VidModeExtension
[ 485.569] (II) Loading extension XFree86-DGA
[ 485.569] (II) Loading extension DPMS
[ 485.569] (II) Loading extension XVideo
[ 485.569] (II) Loading extension XVideo-MotionCompensation
[ 485.569] (II) Loading extension X-Resource
[ 485.569] (II) LoadModule: "glx"
[ 485.569] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 485.588] (II) Module glx: vendor="NVIDIA Corporation"
[ 485.588] compiled for 4.0.2, module version = 1.0.0
[ 485.589] Module class: X.Org Server Extension
[ 485.589] (II) NVIDIA GLX Module 270.41.06 Mon Apr 18 15:11:28 PDT 2011
[ 485.589] (II) Loading extension GLX
[ 485.589] (II) LoadModule: "record"
[ 485.589] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 485.589] (II) Module record: vendor="X.Org Foundation"
[ 485.589] compiled for 1.10.1, module version = 1.13.0
[ 485.589] Module class: X.Org Server Extension
[ 485.589] ABI class: X.Org Server Extension, version 5.0
[ 485.589] (II) Loading extension RECORD
[ 485.589] (II) LoadModule: "dbe"
[ 485.589] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 485.589] (II) Module dbe: vendor="X.Org Foundation"
[ 485.589] compiled for 1.10.1, module version = 1.0.0
[ 485.589] Module class: X.Org Server Extension
[ 485.589] ABI class: X.Org Server Extension, version 5.0
[ 485.589] (II) Loading extension DOUBLE-BUFFER
[ 485.589] (II) LoadModule: "dri2"
[ 485.589] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 485.589] (II) Module dri2: vendor="X.Org Foundation"
[ 485.589] compiled for 1.10.1, module version = 1.2.0
[ 485.589] ABI class: X.Org Server Extension, version 5.0
[ 485.589] (II) Loading extension DRI2
[ 485.589] (II) LoadModule: "dri"
[ 485.589] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 485.589] (II) Module dri: vendor="X.Org Foundation"
[ 485.589] compiled for 1.10.1, module version = 1.0.0
[ 485.589] ABI class: X.Org Server Extension, version 5.0
[ 485.589] (II) Loading extension XFree86-DRI
[ 485.589] (II) LoadModule: "nvidia"
[ 485.589] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 485.590] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 485.590] compiled for 4.0.2, module version = 1.0.0
[ 485.590] Module class: X.Org Video Driver
[ 485.590] (II) NVIDIA dlloader X Driver 270.41.06 Mon Apr 18 14:55:51 PDT 2011
[ 485.590] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[ 485.590] (--) using VT number 7
[ 485.593] (II) Loading sub module "fb"
[ 485.593] (II) LoadModule: "fb"
[ 485.593] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 485.593] (II) Module fb: vendor="X.Org Foundation"
[ 485.593] compiled for 1.10.1, module version = 1.0.0
[ 485.593] ABI class: X.Org ANSI C Emulation, version 0.4
[ 485.593] (II) Loading sub module "wfb"
[ 485.593] (II) LoadModule: "wfb"
[ 485.593] (II) Loading /usr/lib/xorg/modules/libwfb.so
[ 485.593] (II) Module wfb: vendor="X.Org Foundation"
[ 485.593] compiled for 1.10.1, module version = 1.0.0
[ 485.593] ABI class: X.Org ANSI C Emulation, version 0.4
[ 485.593] (II) Loading sub module "ramdac"
[ 485.593] (II) LoadModule: "ramdac"
[ 485.593] (II) Module "ramdac" already built-in
[ 485.593] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 485.593] (II) Loading /usr/lib/xorg/modules/libwfb.so
[ 485.593] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 485.593] (==) NVIDIA(0): Depth 24, (==) framebuffer bpp 32
[ 485.593] (==) NVIDIA(0): RGB weight 888
[ 485.593] (==) NVIDIA(0): Default visual is TrueColor
[ 485.593] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[ 485.593] (**) NVIDIA(0): Option "RenderAccel" "true"
[ 485.593] (**) NVIDIA(0): Enabling RENDER acceleration
[ 485.953] (II) NVIDIA(GPU-0): Display (LG Electronics L222W (CRT-0)) does not support NVIDIA
[ 485.953] (II) NVIDIA(GPU-0): 3D Vision stereo.
[ 485.986] (II) NVIDIA(GPU-0): Display (PANASONIC-TV (DFP-1)) does not support NVIDIA 3D
[ 485.986] (II) NVIDIA(GPU-0): Vision stereo.
[ 485.987] (II) NVIDIA(0): NVIDIA GPU GeForce 210 (GT218) at PCI:1:0:0 (GPU-0)
[ 485.987] (--) NVIDIA(0): Memory: 1048576 kBytes
[ 485.987] (--) NVIDIA(0): VideoBIOS: 70.18.39.00.17
[ 485.987] (II) NVIDIA(0): Detected PCI Express Link width: 16X
[ 485.987] (--) NVIDIA(0): Interlaced video modes are supported on this GPU
[ 485.987] (--) NVIDIA(0): Connected display device(s) on GeForce 210 at PCI:1:0:0
[ 485.987] (--) NVIDIA(0): LG Electronics L222W (CRT-0)
[ 485.987] (--) NVIDIA(0): PANASONIC-TV (DFP-1)
[ 485.987] (--) NVIDIA(0): LG Electronics L222W (CRT-0): 400.0 MHz maximum pixel clock
[ 485.987] (--) NVIDIA(0): PANASONIC-TV (DFP-1): 165.0 MHz maximum pixel clock
[ 485.987] (--) NVIDIA(0): PANASONIC-TV (DFP-1): Internal Single Link TMDS
[ 486.026] (II) NVIDIA(0): Assigned Display Device: CRT-0
[ 486.026] (==) NVIDIA(0):
[ 486.026] (==) NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select"
[ 486.026] (==) NVIDIA(0): will be used as the requested mode.
[ 486.026] (==) NVIDIA(0):
[ 486.026] (II) NVIDIA(0): Validated modes:
[ 486.026] (II) NVIDIA(0): "nvidia-auto-select"
[ 486.026] (II) NVIDIA(0): Virtual screen size determined to be 1680 x 1050
[ 486.054] (--) NVIDIA(0): DPI set to (90, 88); computed from "UseEdidDpi" X config
[ 486.054] (--) NVIDIA(0): option
[ 486.054] (--) Depth 24 pixmap format is 32 bpp
[ 486.054] (II) NVIDIA: Using 768.00 MB of virtual memory for indirect memory access.
[ 486.056] (II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
[ 486.056] (II) NVIDIA(0): may not be running or the "AcpidSocketPath" X
[ 486.056] (II) NVIDIA(0): configuration option may not be set correctly. When the
[ 486.056] (II) NVIDIA(0): ACPI event daemon is available, the NVIDIA X driver will
[ 486.056] (II) NVIDIA(0): try to use it to receive ACPI event notifications. For
[ 486.056] (II) NVIDIA(0): details, please see the "ConnectToAcpid" and
[ 486.056] (II) NVIDIA(0): "AcpidSocketPath" X configuration options in Appendix B: X
[ 486.056] (II) NVIDIA(0): Config Options in the README.
[ 486.058] (II) NVIDIA(0): Setting mode "nvidia-auto-select"
[ 486.286] (II) Loading extension NV-GLX
[ 486.314] (==) NVIDIA(0): Disabling shared memory pixmaps
[ 486.314] (==) NVIDIA(0): Backing store disabled
[ 486.314] (==) NVIDIA(0): Silken mouse enabled
[ 486.314] (==) NVIDIA(0): DPMS enabled
[ 486.314] (II) Loading extension NV-CONTROL
[ 486.315] (II) Loading extension XINERAMA
[ 486.315] (II) Loading sub module "dri2"
[ 486.315] (II) LoadModule: "dri2"
[ 486.315] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 486.315] (II) Module dri2: vendor="X.Org Foundation"
[ 486.315] compiled for 1.10.1, module version = 1.2.0
[ 486.315] ABI class: X.Org Server Extension, version 5.0
[ 486.315] (II) NVIDIA(0): [DRI2] Setup complete
[ 486.315] (==) RandR enabled
[ 486.315] (II) Initializing built-in extension Generic Event Extension
[ 486.315] (II) Initializing built-in extension SHAPE
[ 486.315] (II) Initializing built-in extension MIT-SHM
[ 486.315] (II) Initializing built-in extension XInputExtension
[ 486.315] (II) Initializing built-in extension XTEST
[ 486.315] (II) Initializing built-in extension BIG-REQUESTS
[ 486.315] (II) Initializing built-in extension SYNC
[ 486.315] (II) Initializing built-in extension XKEYBOARD
[ 486.315] (II) Initializing built-in extension XC-MISC
[ 486.315] (II) Initializing built-in extension SECURITY
[ 486.315] (II) Initializing built-in extension XINERAMA
[ 486.315] (II) Initializing built-in extension XFIXES
[ 486.315] (II) Initializing built-in extension RENDER
[ 486.315] (II) Initializing built-in extension RANDR
[ 486.315] (II) Initializing built-in extension COMPOSITE
[ 486.315] (II) Initializing built-in extension DAMAGE
[ 486.317] (II) Initializing extension GLX
[ 486.364] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 486.364] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 486.364] (**) Power Button: Applying InputClass "Keyboard Defaults"
[ 486.364] (II) LoadModule: "evdev"
[ 486.365] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 486.365] (II) Module evdev: vendor="X.Org Foundation"
[ 486.365] compiled for 1.10.0, module version = 2.6.0
[ 486.365] Module class: X.Org XInput Driver
[ 486.365] ABI class: X.Org XInput driver, version 12.2
[ 486.365] (II) Using input driver 'evdev' for 'Power Button'
[ 486.365] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 486.365] (**) Power Button: always reports core events
[ 486.365] (**) Power Button: Device: "/dev/input/event1"
[ 486.376] (--) Power Button: Found keys
[ 486.376] (II) Power Button: Configuring as keyboard
[ 486.376] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1/event1"
[ 486.376] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[ 486.376] (**) Option "xkb_rules" "evdev"
[ 486.376] (**) Option "xkb_model" "evdev"
[ 486.376] (**) Option "xkb_layout" "fr"
[ 486.397] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[ 486.397] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 486.397] (**) Power Button: Applying InputClass "Keyboard Defaults"
[ 486.397] (II) Using input driver 'evdev' for 'Power Button'
[ 486.397] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 486.397] (**) Power Button: always reports core events
[ 486.397] (**) Power Button: Device: "/dev/input/event0"
[ 486.413] (--) Power Button: Found keys
[ 486.413] (II) Power Button: Configuring as keyboard
[ 486.413] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0/event0"
[ 486.413] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
[ 486.413] (**) Option "xkb_rules" "evdev"
[ 486.413] (**) Option "xkb_model" "evdev"
[ 486.413] (**) Option "xkb_layout" "fr"
[ 486.415] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event2)
[ 486.415] (II) No input driver/identifier specified (ignoring)
[ 486.418] (II) config/udev: Adding input device Microsoft Wired Keyboard 600 (/dev/input/event3)
[ 486.418] (**) Microsoft Wired Keyboard 600: Applying InputClass "evdev keyboard catchall"
[ 486.418] (**) Microsoft Wired Keyboard 600: Applying InputClass "Keyboard Defaults"
[ 486.418] (II) Using input driver 'evdev' for 'Microsoft Wired Keyboard 600'
[ 486.418] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 486.418] (**) Microsoft Wired Keyboard 600: always reports core events
[ 486.418] (**) Microsoft Wired Keyboard 600: Device: "/dev/input/event3"
[ 486.430] (--) Microsoft Wired Keyboard 600: Found keys
[ 486.430] (II) Microsoft Wired Keyboard 600: Configuring as keyboard
[ 486.430] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.1/usb9/9-1/9-1:1.0/input/input3/event3"
[ 486.430] (II) XINPUT: Adding extended input device "Microsoft Wired Keyboard 600" (type: KEYBOARD)
[ 486.430] (**) Option "xkb_rules" "evdev"
[ 486.430] (**) Option "xkb_model" "evdev"
[ 486.430] (**) Option "xkb_layout" "fr"
[ 486.430] (II) config/udev: Adding input device Microsoft Wired Keyboard 600 (/dev/input/event4)
[ 486.430] (**) Microsoft Wired Keyboard 600: Applying InputClass "evdev keyboard catchall"
[ 486.430] (**) Microsoft Wired Keyboard 600: Applying InputClass "Keyboard Defaults"
[ 486.430] (II) Using input driver 'evdev' for 'Microsoft Wired Keyboard 600'
[ 486.430] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 486.430] (**) Microsoft Wired Keyboard 600: always reports core events
[ 486.430] (**) Microsoft Wired Keyboard 600: Device: "/dev/input/event4"
[ 486.446] (--) Microsoft Wired Keyboard 600: Found 1 mouse buttons
[ 486.446] (--) Microsoft Wired Keyboard 600: Found scroll wheel(s)
[ 486.446] (--) Microsoft Wired Keyboard 600: Found relative axes
[ 486.446] (--) Microsoft Wired Keyboard 600: Found absolute axes
[ 486.446] (--) Microsoft Wired Keyboard 600: Found x and y absolute axes
[ 486.446] (--) Microsoft Wired Keyboard 600: Found keys
[ 486.446] (II) Microsoft Wired Keyboard 600: Configuring as mouse
[ 486.446] (II) Microsoft Wired Keyboard 600: Configuring as keyboard
[ 486.446] (II) Microsoft Wired Keyboard 600: Adding scrollwheel support
[ 486.446] (**) Microsoft Wired Keyboard 600: YAxisMapping: buttons 4 and 5
[ 486.446] (**) Microsoft Wired Keyboard 600: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 486.446] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.1/usb9/9-1/9-1:1.1/input/input4/event4"
[ 486.446] (II) XINPUT: Adding extended input device "Microsoft Wired Keyboard 600" (type: KEYBOARD)
[ 486.446] (**) Option "xkb_rules" "evdev"
[ 486.446] (**) Option "xkb_model" "evdev"
[ 486.446] (**) Option "xkb_layout" "fr"
[ 486.447] (EE) Microsoft Wired Keyboard 600: failed to initialize for relative axes.
[ 486.447] (WW) Microsoft Wired Keyboard 600: found 37 axes, limiting to 36.
[ 486.447] (II) Microsoft Wired Keyboard 600: initialized for absolute axes.
[ 486.447] (**) Microsoft Wired Keyboard 600: (accel) keeping acceleration scheme 1
[ 486.447] (**) Microsoft Wired Keyboard 600: (accel) acceleration profile 0
[ 486.447] (**) Microsoft Wired Keyboard 600: (accel) acceleration factor: 2.000
[ 486.447] (**) Microsoft Wired Keyboard 600: (accel) acceleration threshold: 4
[ 486.447] (II) config/udev: Adding input device Microsoft Wired Keyboard 600 (/dev/input/js0)
[ 486.447] (**) Microsoft Wired Keyboard 600: Applying InputClass "Keyboard Defaults"
[ 486.447] (II) No input driver/identifier specified (ignoring)
[ 486.447] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/event5)
[ 486.447] (**) Logitech USB Optical Mouse: Applying InputClass "evdev pointer catchall"
[ 486.447] (II) Using input driver 'evdev' for 'Logitech USB Optical Mouse'
[ 486.447] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 486.447] (**) Logitech USB Optical Mouse: always reports core events
[ 486.447] (**) Logitech USB Optical Mouse: Device: "/dev/input/event5"
[ 486.473] (--) Logitech USB Optical Mouse: Found 12 mouse buttons
[ 486.473] (--) Logitech USB Optical Mouse: Found scroll wheel(s)
[ 486.473] (--) Logitech USB Optical Mouse: Found relative axes
[ 486.473] (--) Logitech USB Optical Mouse: Found x and y relative axes
[ 486.473] (II) Logitech USB Optical Mouse: Configuring as mouse
[ 486.473] (II) Logitech USB Optical Mouse: Adding scrollwheel support
[ 486.473] (**) Logitech USB Optical Mouse: YAxisMapping: buttons 4 and 5
[ 486.473] (**) Logitech USB Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 486.473] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.1/usb9/9-2/9-2:1.0/input/input5/event5"
[ 486.473] (II) XINPUT: Adding extended input device "Logitech USB Optical Mouse" (type: MOUSE)
[ 486.473] (II) Logitech USB Optical Mouse: initialized for relative axes.
[ 486.473] (**) Logitech USB Optical Mouse: (accel) keeping acceleration scheme 1
[ 486.473] (**) Logitech USB Optical Mouse: (accel) acceleration profile 0
[ 486.473] (**) Logitech USB Optical Mouse: (accel) acceleration factor: 2.000
[ 486.473] (**) Logitech USB Optical Mouse: (accel) acceleration threshold: 4
[ 486.473] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/mouse0)
[ 486.473] (II) No input driver/identifier specified (ignoring)
[ 525.530] (WW) NVIDIA(0): The NVIDIA X driver has encountered too many errors. Falling
[ 525.530] (WW) NVIDIA(0): back to write-back cached memory.
dmesg.txt
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.38-ARCH (tobias@T-POWA-LX) (gcc version 4.6.0 20110415 (prerelease) (GCC) ) #1 SMP PREEMPT Fri Apr 22 17:48:36 UTC 2011
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
[ 0.000000] BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007ff90000 (usable)
[ 0.000000] BIOS-e820: 000000007ff90000 - 000000007ff9e000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007ff9e000 - 000000007ffe0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
[ 0.000000] DMI 2.4 present.
[ 0.000000] DMI: System manufacturer System Product Name/P5B-Deluxe, BIOS 1238 09/30/2008
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[ 0.000000] last_pfn = 0x7ff90 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-DFFFF uncachable
[ 0.000000] E0000-EFFFF write-through
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask F80000000 write-back
[ 0.000000] 1 disabled
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] found SMP MP-table at [c00ff780] ff780
[ 0.000000] initial memory mapped : 0 - 01800000
[ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 0037400000 page 2M
[ 0.000000] 0037400000 - 00377fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 377fe000 @ 17fb000-1800000
[ 0.000000] RAMDISK: 7fdd0000 - 7ff80000
[ 0.000000] Allocated new RAMDISK: 3764e000 - 377fd262
[ 0.000000] Move RAMDISK from 000000007fdd0000 - 000000007ff7f261 to 3764e000 - 377fd261
[ 0.000000] ACPI: RSDP 000fae70 00024 (v02 ACPIAM)
[ 0.000000] ACPI: XSDT 7ff90100 0004C (v01 MSTEST OEMXSDT 09000830 MSFT 00000097)
[ 0.000000] ACPI: FACP 7ff90290 000F4 (v03 MSTEST OEMFACP 09000830 MSFT 00000097)
[ 0.000000] ACPI: DSDT 7ff905c0 0918E (v01 A0483 A0483035 00000035 INTL 20060113)
[ 0.000000] ACPI: FACS 7ff9e000 00040
[ 0.000000] ACPI: APIC 7ff90390 0006C (v01 MSTEST OEMAPIC 09000830 MSFT 00000097)
[ 0.000000] ACPI: MCFG 7ff90400 0003C (v01 MSTEST OEMMCFG 09000830 MSFT 00000097)
[ 0.000000] ACPI: OEMB 7ff9e040 0007B (v01 MSTEST AMI_OEM 09000830 MSFT 00000097)
[ 0.000000] ACPI: HPET 7ff99750 00038 (v01 MSTEST OEMHPET 09000830 MSFT 00000097)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 1159MB HIGHMEM available.
[ 0.000000] 887MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 377fe000
[ 0.000000] low ram: 0 - 377fe000
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000377fe
[ 0.000000] HighMem 0x000377fe -> 0x0007ff90
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009e
[ 0.000000] 0: 0x00000100 -> 0x0007ff90
[ 0.000000] On node 0 totalpages: 524062
[ 0.000000] free_area_init_node: node 0, pgdat c1450b00, node_mem_map f664d200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3950 pages, LIFO batch:0
[ 0.000000] Normal zone: 1744 pages used for memmap
[ 0.000000] Normal zone: 221486 pages, LIFO batch:31
[ 0.000000] HighMem zone: 2320 pages used for memmap
[ 0.000000] HighMem zone: 294530 pages, LIFO batch:31
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a202 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
[ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:7ee00000)
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 12 pages/cpu @f6000000 s27392 r0 d21760 u1048576
[ 0.000000] pcpu-alloc: s27392 r0 d21760 u1048576 alloc=1*4194304
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519966
[ 0.000000] Kernel command line: root=/dev/sda3 ro
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240
[ 0.000000] allocated 10483200 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Initializing HighMem for node 0 (000377fe:0007ff90)
[ 0.000000] Memory: 2061020k/2096704k available (3182k kernel code, 35228k reserved, 1259k data, 424k init, 1187400k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
[ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
[ 0.000000] .init : 0xc1457000 - 0xc14c1000 ( 424 kB)
[ 0.000000] .data : 0xc131bacb - 0xc1456a00 (1259 kB)
[ 0.000000] .text : 0xc1000000 - 0xc131bacb (3182 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptable hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] Verbose stalled-CPUs detection is disabled.
[ 0.000000] NR_IRQS:512
[ 0.000000] CPU 0 irqstacks, hard=f500c000 soft=f500e000
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 3066.221 MHz processor.
[ 0.003336] Calibrating delay loop (skipped), value calculated using timer frequency.. 6134.96 BogoMIPS (lpj=10220736)
[ 0.003418] pid_max: default: 32768 minimum: 301
[ 0.003486] Security Framework initialized
[ 0.003528] AppArmor: AppArmor disabled by boot time parameter
[ 0.006682] Mount-cache hash table entries: 512
[ 0.006865] Initializing cgroup subsys ns
[ 0.006906] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
[ 0.006960] Initializing cgroup subsys cpuacct
[ 0.007007] Initializing cgroup subsys memory
[ 0.007052] Initializing cgroup subsys devices
[ 0.007092] Initializing cgroup subsys freezer
[ 0.007133] Initializing cgroup subsys net_cls
[ 0.007172] Initializing cgroup subsys blkio
[ 0.007238] CPU: Physical Processor ID: 0
[ 0.007277] CPU: Processor Core ID: 0
[ 0.007317] mce: CPU supports 6 MCE banks
[ 0.007361] CPU0: Thermal monitoring enabled (TM2)
[ 0.007402] using mwait in idle threads.
[ 0.008216] ACPI: Core revision 20110112
[ 0.013386] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.013726] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.046907] CPU0: Intel(R) Core(TM)2 Duo CPU E7600 @ 3.06GHz stepping 0a
[ 0.049997] Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
[ 0.049997] ... version: 2
[ 0.049997] ... bit width: 40
[ 0.049997] ... generic registers: 2
[ 0.049997] ... value mask: 000000ffffffffff
[ 0.049997] ... max period: 000000007fffffff
[ 0.049997] ... fixed-purpose events: 3
[ 0.049997] ... event mask: 0000000700000003
[ 0.056745] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.070012] CPU 1 irqstacks, hard=f50d6000 soft=f50d8000
[ 0.070017] Booting Node 0, Processors #1
[ 0.006666] Initializing CPU#1
[ 0.166676] NMI watchdog enabled, takes one hw-pmu counter.
[ 0.169997] Brought up 2 CPUs
[ 0.170040] Total of 2 processors activated (12270.81 BogoMIPS).
[ 0.171248] devtmpfs: initialized
[ 0.171248] NET: Registered protocol family 16
[ 0.171248] ACPI: bus type pci registered
[ 0.171248] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.171248] PCI: not using MMCONFIG
[ 0.171248] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
[ 0.171248] PCI: Using configuration type 1 for base access
[ 0.171248] bio: create slab <bio-0> at 0
[ 0.173388] ACPI: EC: Look up EC in DSDT
[ 0.174194] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.179022] ACPI: SSDT 7ff9e0c0 00208 (v01 AMI CPU1PM 00000001 INTL 20060113)
[ 0.179316] ACPI: Dynamic OEM Table Load:
[ 0.179408] ACPI: SSDT (null) 00208 (v01 AMI CPU1PM 00000001 INTL 20060113)
[ 0.179643] ACPI: SSDT 7ff9e2d0 0013A (v01 AMI CPU2PM 00000001 INTL 20060113)
[ 0.179932] ACPI: Dynamic OEM Table Load:
[ 0.180025] ACPI: SSDT (null) 0013A (v01 AMI CPU2PM 00000001 INTL 20060113)
[ 0.180248] ACPI: Interpreter enabled
[ 0.180292] ACPI: (supports S0 S3 S4 S5)
[ 0.180445] ACPI: Using IOAPIC for interrupt routing
[ 0.180500] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.180904] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[ 0.180958] PCI: Using MMCONFIG for extended config space
[ 0.185933] ACPI: No dock devices found.
[ 0.185973] HEST: Table not found.
[ 0.186014] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.186114] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.186260] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.186304] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.186346] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.186398] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000dffff]
[ 0.186450] pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xffffffff]
[ 0.186509] pci 0000:00:00.0: [8086:29a0] type 0 class 0x000600
[ 0.186539] pci 0000:00:01.0: [8086:29a1] type 1 class 0x000604
[ 0.186562] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.186564] pci 0000:00:01.0: PME# disabled
[ 0.186592] pci 0000:00:1a.0: [8086:2834] type 0 class 0x000c03
[ 0.186625] pci 0000:00:1a.0: reg 20: [io 0xa880-0xa89f]
[ 0.186660] pci 0000:00:1a.1: [8086:2835] type 0 class 0x000c03
[ 0.186692] pci 0000:00:1a.1: reg 20: [io 0xac00-0xac1f]
[ 0.186724] pci 0000:00:1a.7: [8086:283a] type 0 class 0x000c03
[ 0.186740] pci 0000:00:1a.7: reg 10: [mem 0xf9fffc00-0xf9ffffff]
[ 0.186797] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
[ 0.186801] pci 0000:00:1a.7: PME# disabled
[ 0.186817] pci 0000:00:1b.0: [8086:284b] type 0 class 0x000403
[ 0.186829] pci 0000:00:1b.0: reg 10: [mem 0xf9ff8000-0xf9ffbfff 64bit]
[ 0.186873] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.186876] pci 0000:00:1b.0: PME# disabled
[ 0.186891] pci 0000:00:1c.0: [8086:283f] type 1 class 0x000604
[ 0.186935] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.186938] pci 0000:00:1c.0: PME# disabled
[ 0.186956] pci 0000:00:1c.4: [8086:2847] type 1 class 0x000604
[ 0.187000] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.187003] pci 0000:00:1c.4: PME# disabled
[ 0.187019] pci 0000:00:1c.5: [8086:2849] type 1 class 0x000604
[ 0.187063] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 0.187066] pci 0000:00:1c.5: PME# disabled
[ 0.187082] pci 0000:00:1d.0: [8086:2830] type 0 class 0x000c03
[ 0.187114] pci 0000:00:1d.0: reg 20: [io 0xa400-0xa41f]
[ 0.187137] pci 0000:00:1d.1: [8086:2831] type 0 class 0x000c03
[ 0.187170] pci 0000:00:1d.1: reg 20: [io 0xa480-0xa49f]
[ 0.187193] pci 0000:00:1d.2: [8086:2832] type 0 class 0x000c03
[ 0.187226] pci 0000:00:1d.2: reg 20: [io 0xa800-0xa81f]
[ 0.187256] pci 0000:00:1d.7: [8086:2836] type 0 class 0x000c03
[ 0.187272] pci 0000:00:1d.7: reg 10: [mem 0xf9fff800-0xf9fffbff]
[ 0.187329] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.187333] pci 0000:00:1d.7: PME# disabled
[ 0.187346] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604
[ 0.187393] pci 0000:00:1f.0: [8086:2810] type 0 class 0x000601
[ 0.187462] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0294 (mask 0003)
[ 0.188664] pci 0000:00:1f.2: [8086:2821] type 0 class 0x000106
[ 0.188677] pci 0000:00:1f.2: reg 10: [io 0xa080-0xa087]
[ 0.188684] pci 0000:00:1f.2: reg 14: [io 0xa000-0xa003]
[ 0.188690] pci 0000:00:1f.2: reg 18: [io 0x9c00-0x9c07]
[ 0.188696] pci 0000:00:1f.2: reg 1c: [io 0x9880-0x9883]
[ 0.188703] pci 0000:00:1f.2: reg 20: [io 0x9800-0x981f]
[ 0.188709] pci 0000:00:1f.2: reg 24: [mem 0xf9fff000-0xf9fff7ff]
[ 0.188733] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.188736] pci 0000:00:1f.2: PME# disabled
[ 0.188747] pci 0000:00:1f.3: [8086:283e] type 0 class 0x000c05
[ 0.188756] pci 0000:00:1f.3: reg 10: [mem 0x00000000-0x000000ff]
[ 0.188778] pci 0000:00:1f.3: reg 20: [io 0x0400-0x041f]
[ 0.188824] pci 0000:01:00.0: [10de:0a65] type 0 class 0x000300
[ 0.188832] pci 0000:01:00.0: reg 10: [mem 0xfa000000-0xfaffffff]
[ 0.188841] pci 0000:01:00.0: reg 14: [mem 0xd0000000-0xdfffffff 64bit pref]
[ 0.188849] pci 0000:01:00.0: reg 1c: [mem 0xce000000-0xcfffffff 64bit pref]
[ 0.188856] pci 0000:01:00.0: reg 24: [io 0xbc00-0xbc7f]
[ 0.188862] pci 0000:01:00.0: reg 30: [mem 0xfbc00000-0xfbc7ffff pref]
[ 0.188895] pci 0000:01:00.1: [10de:0be3] type 0 class 0x000403
[ 0.188903] pci 0000:01:00.1: reg 10: [mem 0xfbcfc000-0xfbcfffff]
[ 0.188969] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.189011] pci 0000:00:01.0: bridge window [io 0xb000-0xbfff]
[ 0.189014] pci 0000:00:01.0: bridge window [mem 0xfa000000-0xfbcfffff]
[ 0.189017] pci 0000:00:01.0: bridge window [mem 0xce000000-0xdfffffff 64bit pref]
[ 0.189048] pci 0000:00:1c.0: PCI bridge to [bus 04-04]
[ 0.189091] pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled)
[ 0.189094] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
[ 0.189098] pci 0000:00:1c.0: bridge window [mem 0xf8f00000-0xf8ffffff 64bit pref]
[ 0.189144] pci 0000:03:00.0: [197b:2363] type 0 class 0x000101
[ 0.189223] pci 0000:03:00.0: reg 24: [mem 0xfbefe000-0xfbefffff]
[ 0.189236] pci 0000:03:00.0: reg 30: [mem 0xfbee0000-0xfbeeffff pref]
[ 0.189263] pci 0000:03:00.0: PME# supported from D3hot
[ 0.189268] pci 0000:03:00.0: PME# disabled
[ 0.189293] pci 0000:03:00.1: [197b:2363] type 0 class 0x000101
[ 0.189315] pci 0000:03:00.1: reg 10: [io 0xdc00-0xdc07]
[ 0.189327] pci 0000:03:00.1: reg 14: [io 0xd880-0xd883]
[ 0.189339] pci 0000:03:00.1: reg 18: [io 0xd800-0xd807]
[ 0.189351] pci 0000:03:00.1: reg 1c: [io 0xd480-0xd483]
[ 0.189363] pci 0000:03:00.1: reg 20: [io 0xd400-0xd40f]
[ 0.189426] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.189491] pci 0000:00:1c.4: PCI bridge to [bus 03-03]
[ 0.189533] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
[ 0.189536] pci 0000:00:1c.4: bridge window [mem 0xfbe00000-0xfbefffff]
[ 0.189540] pci 0000:00:1c.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.189589] pci 0000:02:00.0: [11ab:4364] type 0 class 0x000200
[ 0.189609] pci 0000:02:00.0: reg 10: [mem 0xfbdfc000-0xfbdfffff 64bit]
[ 0.189620] pci 0000:02:00.0: reg 18: [io 0xc800-0xc8ff]
[ 0.189658] pci 0000:02:00.0: reg 30: [mem 0xfbdc0000-0xfbddffff pref]
[ 0.189693] pci 0000:02:00.0: supports D1 D2
[ 0.189694] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.189698] pci 0000:02:00.0: PME# disabled
[ 0.193338] pci 0000:00:1c.5: PCI bridge to [bus 02-02]
[ 0.193385] pci 0000:00:1c.5: bridge window [io 0xc000-0xcfff]
[ 0.193390] pci 0000:00:1c.5: bridge window [mem 0xfbd00000-0xfbdfffff]
[ 0.193397] pci 0000:00:1c.5: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.193434] pci 0000:05:02.0: [1033:0035] type 0 class 0x000c03
[ 0.193452] pci 0000:05:02.0: reg 10: [mem 0xfbffd000-0xfbffdfff]
[ 0.193514] pci 0000:05:02.0: supports D1 D2
[ 0.193516] pci 0000:05:02.0: PME# supported from D0 D1 D2 D3hot
[ 0.193519] pci 0000:05:02.0: PME# disabled
[ 0.193533] pci 0000:05:02.1: [1033:0035] type 0 class 0x000c03
[ 0.193546] pci 0000:05:02.1: reg 10: [mem 0xfbffe000-0xfbffefff]
[ 0.193601] pci 0000:05:02.1: supports D1 D2
[ 0.193602] pci 0000:05:02.1: PME# supported from D0 D1 D2 D3hot
[ 0.193605] pci 0000:05:02.1: PME# disabled
[ 0.193619] pci 0000:05:02.2: [1033:00e0] type 0 class 0x000c03
[ 0.193633] pci 0000:05:02.2: reg 10: [mem 0xfbfffc00-0xfbfffcff]
[ 0.193687] pci 0000:05:02.2: supports D1 D2
[ 0.193689] pci 0000:05:02.2: PME# supported from D0 D1 D2 D3hot
[ 0.193692] pci 0000:05:02.2: PME# disabled
[ 0.193711] pci 0000:05:03.0: [104c:8023] type 0 class 0x000c00
[ 0.193726] pci 0000:05:03.0: reg 10: [mem 0xfbfff000-0xfbfff7ff]
[ 0.193735] pci 0000:05:03.0: reg 14: [mem 0xfbff8000-0xfbffbfff]
[ 0.193786] pci 0000:05:03.0: supports D1 D2
[ 0.193787] pci 0000:05:03.0: PME# supported from D0 D1 D2 D3hot
[ 0.193791] pci 0000:05:03.0: PME# disabled
[ 0.193806] pci 0000:05:04.0: [11ab:4320] type 0 class 0x000200
[ 0.193823] pci 0000:05:04.0: reg 10: [mem 0xfbff4000-0xfbff7fff]
[ 0.193831] pci 0000:05:04.0: reg 14: [io 0xe800-0xe8ff]
[ 0.193867] pci 0000:05:04.0: reg 30: [mem 0xfbfc0000-0xfbfdffff pref]
[ 0.193886] pci 0000:05:04.0: supports D1 D2
[ 0.193888] pci 0000:05:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.193891] pci 0000:05:04.0: PME# disabled
[ 0.193926] pci 0000:00:1e.0: PCI bridge to [bus 05-05] (subtractive decode)
[ 0.193971] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
[ 0.193974] pci 0000:00:1e.0: bridge window [mem 0xfbf00000-0xfbffffff]
[ 0.193978] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
[ 0.193980] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.193982] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.193983] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.193985] pci 0000:00:1e.0: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
[ 0.193987] pci 0000:00:1e.0: bridge window [mem 0x80000000-0xffffffff] (subtractive decode)
[ 0.194003] pci_bus 0000:00: on NUMA node 0
[ 0.194005] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.194127] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[ 0.194156] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.194243] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 0.194277] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
[ 0.194313] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[ 0.194355] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.199969] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.200342] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.200724] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.201105] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
[ 0.201486] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.201868] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
[ 0.202249] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 0.202634] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[ 0.203051] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.203107] vgaarb: loaded
[ 0.203206] PCI: Using ACPI for IRQ routing
[ 0.203247] PCI: pci_cache_line_size set to 64 bytes
[ 0.203358] reserve RAM buffer: 000000000009ec00 - 000000000009ffff
[ 0.203360] reserve RAM buffer: 000000007ff90000 - 000000007fffffff
[ 0.203439] NetLabel: Initializing
[ 0.203478] NetLabel: domain hash size = 128
[ 0.203518] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.203565] NetLabel: unlabeled traffic allowed by default
[ 0.203608] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.203653] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.203797] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.210012] Switching to clocksource hpet
[ 0.211034] pnp: PnP ACPI init
[ 0.211084] ACPI: bus type pnp registered
[ 0.211173] pnp 00:00: [bus 00-ff]
[ 0.211175] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.211177] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.211179] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.211180] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.211182] pnp 00:00: [mem 0x000d0000-0x000dffff window]
[ 0.211184] pnp 00:00: [mem 0x80000000-0xffffffff window]
[ 0.211222] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.211229] pnp 00:01: [mem 0xfed14000-0xfed19fff]
[ 0.211267] system 00:01: [mem 0xfed14000-0xfed19fff] has been reserved
[ 0.211311] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.211335] pnp 00:02: [dma 4]
[ 0.211337] pnp 00:02: [io 0x0000-0x000f]
[ 0.211338] pnp 00:02: [io 0x0081-0x0083]
[ 0.211339] pnp 00:02: [io 0x0087]
[ 0.211341] pnp 00:02: [io 0x0089-0x008b]
[ 0.211342] pnp 00:02: [io 0x008f]
[ 0.211343] pnp 00:02: [io 0x00c0-0x00df]
[ 0.211367] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.211374] pnp 00:03: [io 0x0070-0x0071]
[ 0.211380] pnp 00:03: [irq 8]
[ 0.211403] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.211412] pnp 00:04: [io 0x0061]
[ 0.211435] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.211441] pnp 00:05: [io 0x00f0-0x00ff]
[ 0.211444] pnp 00:05: [irq 13]
[ 0.211469] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.211669] pnp 00:06: [irq 4]
[ 0.211671] pnp 00:06: [dma 0 disabled]
[ 0.211672] pnp 00:06: [io 0x03f8-0x03ff]
[ 0.211721] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.211835] pnp 00:07: [io 0x0000-0xffffffff disabled]
[ 0.211837] pnp 00:07: [io 0x0000-0xffffffff disabled]
[ 0.211838] pnp 00:07: [io 0x0290-0x0297]
[ 0.211879] system 00:07: [io 0x0290-0x0297] has been reserved
[ 0.211922] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.211997] pnp 00:08: [io 0x0010-0x001f]
[ 0.211999] pnp 00:08: [io 0x0022-0x003f]
[ 0.212000] pnp 00:08: [io 0x0044-0x005f]
[ 0.212002] pnp 00:08: [io 0x0062-0x0063]
[ 0.212003] pnp 00:08: [io 0x0065-0x006f]
[ 0.212004] pnp 00:08: [io 0x0072-0x007f]
[ 0.212006] pnp 00:08: [io 0x0080]
[ 0.212007] pnp 00:08: [io 0x0084-0x0086]
[ 0.212008] pnp 00:08: [io 0x0088]
[ 0.212010] pnp 00:08: [io 0x008c-0x008e]
[ 0.212011] pnp 00:08: [io 0x0090-0x009f]
[ 0.212012] pnp 00:08: [io 0x00a2-0x00bf]
[ 0.212014] pnp 00:08: [io 0x00e0-0x00ef]
[ 0.212015] pnp 00:08: [io 0x04d0-0x04d1]
[ 0.212016] pnp 00:08: [io 0x0800-0x087f]
[ 0.212018] pnp 00:08: [io 0x0400-0x03ff disabled]
[ 0.212019] pnp 00:08: [io 0x0480-0x04bf]
[ 0.212021] pnp 00:08: [mem 0xffafe000-0xffb0cbff]
[ 0.212022] pnp 00:08: [mem 0xffb00000-0xffbfffff]
[ 0.212024] pnp 00:08: [mem 0xfed1c000-0xfed1ffff]
[ 0.212025] pnp 00:08: [mem 0xfed20000-0xfed8ffff]
[ 0.212026] pnp 00:08: [mem 0xfff00000-0xfffffffe]
[ 0.212028] pnp 00:08: [mem 0xfebfe000-0xfebfec00]
[ 0.212089] system 00:08: [io 0x04d0-0x04d1] has been reserved
[ 0.212132] system 00:08: [io 0x0800-0x087f] has been reserved
[ 0.212174] system 00:08: [io 0x0480-0x04bf] has been reserved
[ 0.212216] system 00:08: [mem 0xffafe000-0xffb0cbff] could not be reserved
[ 0.212259] system 00:08: [mem 0xffb00000-0xffbfffff] has been reserved
[ 0.212302] system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.212345] system 00:08: [mem 0xfed20000-0xfed8ffff] has been reserved
[ 0.212388] system 00:08: [mem 0xfff00000-0xfffffffe] has been reserved
[ 0.212430] system 00:08: [mem 0xfebfe000-0xfebfec00] has been reserved
[ 0.212473] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.212521] pnp 00:09: [mem 0xfed00000-0xfed003ff]
[ 0.212547] pnp 00:09: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.212580] pnp 00:0a: [mem 0xfec00000-0xfec00fff]
[ 0.212581] pnp 00:0a: [mem 0xfee00000-0xfee00fff]
[ 0.212625] system 00:0a: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.212668] system 00:0a: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.212712] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.212761] pnp 00:0b: [mem 0xe0000000-0xefffffff]
[ 0.212801] system 00:0b: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.212844] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.212967] pnp 00:0c: [mem 0x00000000-0x0009ffff]
[ 0.212969] pnp 00:0c: [mem 0x000c0000-0x000cffff]
[ 0.212971] pnp 00:0c: [mem 0x000e0000-0x000fffff]
[ 0.212972] pnp 00:0c: [mem 0x00100000-0x7fffffff]
[ 0.212974] pnp 00:0c: [mem 0x00000000-0xffffffff disabled]
[ 0.213025] system 00:0c: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.213068] system 00:0c: [mem 0x000c0000-0x000cffff] could not be reserved
[ 0.213111] system 00:0c: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.213154] system 00:0c: [mem 0x00100000-0x7fffffff] could not be reserved
[ 0.213198] system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.213198] Switched to NOHz mode on CPU #0
[ 0.213237] Switched to NOHz mode on CPU #1
[ 0.213286] pnp: PnP ACPI: found 13 devices
[ 0.213326] ACPI: ACPI bus type pnp unregistered
[ 0.249481] pci 0000:00:1c.0: BAR 14: assigned [mem 0x80000000-0x803fffff]
[ 0.249526] pci 0000:00:1c.4: BAR 15: assigned [mem 0x80400000-0x805fffff 64bit pref]
[ 0.249579] pci 0000:00:1c.5: BAR 15: assigned [mem 0x80600000-0x807fffff 64bit pref]
[ 0.249632] pci 0000:00:1c.0: BAR 13: assigned [io 0x1000-0x1fff]
[ 0.249675] pci 0000:00:1f.3: BAR 0: assigned [mem 0x80800000-0x808000ff]
[ 0.249720] pci 0000:00:1f.3: BAR 0: set to [mem 0x80800000-0x808000ff] (PCI address [0x80800000-0x808000ff])
[ 0.249775] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[ 0.249816] pci 0000:00:01.0: bridge window [io 0xb000-0xbfff]
[ 0.249859] pci 0000:00:01.0: bridge window [mem 0xfa000000-0xfbcfffff]
[ 0.249902] pci 0000:00:01.0: bridge window [mem 0xce000000-0xdfffffff 64bit pref]
[ 0.249956] pci 0000:00:1c.0: PCI bridge to [bus 04-04]
[ 0.250011] pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff]
[ 0.250055] pci 0000:00:1c.0: bridge window [mem 0x80000000-0x803fffff]
[ 0.250099] pci 0000:00:1c.0: bridge window [mem 0xf8f00000-0xf8ffffff 64bit pref]
[ 0.250154] pci 0000:00:1c.4: PCI bridge to [bus 03-03]
[ 0.250195] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
[ 0.250239] pci 0000:00:1c.4: bridge window [mem 0xfbe00000-0xfbefffff]
[ 0.250283] pci 0000:00:1c.4: bridge window [mem 0x80400000-0x805fffff 64bit pref]
[ 0.250338] pci 0000:00:1c.5: PCI bridge to [bus 02-02]
[ 0.250380] pci 0000:00:1c.5: bridge window [io 0xc000-0xcfff]
[ 0.250424] pci 0000:00:1c.5: bridge window [mem 0xfbd00000-0xfbdfffff]
[ 0.250468] pci 0000:00:1c.5: bridge window [mem 0x80600000-0x807fffff 64bit pref]
[ 0.250523] pci 0000:00:1e.0: PCI bridge to [bus 05-05]
[ 0.250565] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
[ 0.250609] pci 0000:00:1e.0: bridge window [mem 0xfbf00000-0xfbffffff]
[ 0.250653] pci 0000:00:1e.0: bridge window [mem pref disabled]
[ 0.250702] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.250746] pci 0000:00:01.0: setting latency timer to 64
[ 0.250750] pci 0000:00:1c.0: enabling device (0106 -> 0107)
[ 0.250792] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.250836] pci 0000:00:1c.0: setting latency timer to 64
[ 0.250840] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.250884] pci 0000:00:1c.4: setting latency timer to 64
[ 0.250890] pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.250933] pci 0000:00:1c.5: setting latency timer to 64
[ 0.250938] pci 0000:00:1e.0: setting latency timer to 64
[ 0.250941] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.250943] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.250944] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.250946] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.250948] pci_bus 0000:00: resource 8 [mem 0x80000000-0xffffffff]
[ 0.250949] pci_bus 0000:01: resource 0 [io 0xb000-0xbfff]
[ 0.250951] pci_bus 0000:01: resource 1 [mem 0xfa000000-0xfbcfffff]
[ 0.250953] pci_bus 0000:01: resource 2 [mem 0xce000000-0xdfffffff 64bit pref]
[ 0.250955] pci_bus 0000:04: resource 0 [io 0x1000-0x1fff]
[ 0.250956] pci_bus 0000:04: resource 1 [mem 0x80000000-0x803fffff]
[ 0.250958] pci_bus 0000:04: resource 2 [mem 0xf8f00000-0xf8ffffff 64bit pref]
[ 0.250960] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff]
[ 0.250961] pci_bus 0000:03: resource 1 [mem 0xfbe00000-0xfbefffff]
[ 0.250963] pci_bus 0000:03: resource 2 [mem 0x80400000-0x805fffff 64bit pref]
[ 0.250965] pci_bus 0000:02: resource 0 [io 0xc000-0xcfff]
[ 0.250966] pci_bus 0000:02: resource 1 [mem 0xfbd00000-0xfbdfffff]
[ 0.250968] pci_bus 0000:02: resource 2 [mem 0x80600000-0x807fffff 64bit pref]
[ 0.250970] pci_bus 0000:05: resource 0 [io 0xe000-0xefff]
[ 0.250972] pci_bus 0000:05: resource 1 [mem 0xfbf00000-0xfbffffff]
[ 0.250973] pci_bus 0000:05: resource 4 [io 0x0000-0x0cf7]
[ 0.250975] pci_bus 0000:05: resource 5 [io 0x0d00-0xffff]
[ 0.250977] pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.250978] pci_bus 0000:05: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.250980] pci_bus 0000:05: resource 8 [mem 0x80000000-0xffffffff]
[ 0.251002] NET: Registered protocol family 2
[ 0.251085] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.251263] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.251592] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.251779] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.251822] TCP reno registered
[ 0.251861] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.251907] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.252025] NET: Registered protocol family 1
[ 0.295104] pci 0000:01:00.0: Boot video device
[ 0.295141] PCI: CLS 32 bytes, default 64
[ 0.295174] Unpacking initramfs...
[ 0.317387] Freeing initrd memory: 1728k freed
[ 0.318002] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 0.318046] apm: disabled - APM is not SMP safe.
[ 0.318193] audit: initializing netlink socket (disabled)
[ 0.318243] type=2000 audit(1303935493.316:1): initialized
[ 0.318520] highmem bounce pool size: 64 pages
[ 0.318562] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.320047] VFS: Disk quotas dquot_6.5.2
[ 0.320145] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.320261] msgmni has been set to 1709
[ 0.320435] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.320488] io scheduler noop registered
[ 0.320527] io scheduler deadline registered
[ 0.320574] io scheduler cfq registered (default)
[ 0.320710] pcieport 0000:00:01.0: setting latency timer to 64
[ 0.320734] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
[ 0.320771] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.320798] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
[ 0.320848] pcieport 0000:00:1c.4: setting latency timer to 64
[ 0.320875] pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X
[ 0.320923] pcieport 0000:00:1c.5: setting latency timer to 64
[ 0.320950] pcieport 0000:00:1c.5: irq 43 for MSI/MSI-X
[ 0.321092] intel_idle: MWAIT substates: 0x22220
[ 0.321094] intel_idle: does not run on family 6 model 23
[ 0.321105] ERST: Table is not found!
[ 0.321155] isapnp: Scanning for PnP cards...
[ 0.676796] isapnp: No Plug & Play device found
[ 0.676877] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.697390] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.920667] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.973728] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 0.976563] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.976631] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.976752] mousedev: PS/2 mouse device common for all mice
[ 0.976847] rtc_cmos 00:03: RTC can wake from S4
[ 1.000070] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 1.000137] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 1.000200] cpuidle: using governor ladder
[ 1.000240] cpuidle: using governor menu
[ 1.000436] TCP cubic registered
[ 1.000476] NET: Registered protocol family 17
[ 1.000521] Registering the dns_resolver key type
[ 1.000569] Using IPI No-Shortcut mode
[ 1.000679] PM: Hibernation image not present or could not be loaded.
[ 1.000682] registered taskstats version 1
[ 1.001054] rtc_cmos 00:03: setting system clock to 2011-04-27 20:18:14 UTC (1303935494)
[ 1.001128] Initalizing network drop monitor service
[ 1.001211] Freeing unused kernel memory: 424k freed
[ 1.005982] <30>udev[38]: starting version 167
[ 1.107427] SCSI subsystem initialized
[ 1.127245] libata version 3.00 loaded.
[ 1.131006] pata_jmicron 0000:03:00.1: enabling device (0000 -> 0001)
[ 1.131057] pata_jmicron 0000:03:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 1.131134] pata_jmicron 0000:03:00.1: setting latency timer to 64
[ 1.131436] scsi0 : pata_jmicron
[ 1.131554] scsi1 : pata_jmicron
[ 1.132024] ata1: PATA max UDMA/100 cmd 0xdc00 ctl 0xd880 bmdma 0xd400 irq 17
[ 1.132068] ata2: PATA max UDMA/100 cmd 0xd800 ctl 0xd480 bmdma 0xd408 irq 17
[ 1.142526] ahci 0000:00:1f.2: version 3.0
[ 1.142536] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.142608] ahci 0000:00:1f.2: irq 44 for MSI/MSI-X
[ 1.142644] ahci: SSS flag set, parallel bus scan disabled
[ 1.142711] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
[ 1.142765] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ccc ems sxs
[ 1.142819] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.174032] scsi2 : ahci
[ 1.174136] scsi3 : ahci
[ 1.174235] scsi4 : ahci
[ 1.174335] scsi5 : ahci
[ 1.174434] scsi6 : ahci
[ 1.174532] scsi7 : ahci
[ 1.174699] ata3: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 44
[ 1.174752] ata4: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 44
[ 1.174804] ata5: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff200 irq 44
[ 1.174856] ata6: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff280 irq 44
[ 1.174908] ata7: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff300 irq 44
[ 1.174960] ata8: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 44
[ 1.175036] ahci 0000:03:00.0: PCI INT A -> GSI 16 (level,Hi jasonwryan,
Your thread helps a lot. I saw a lot of posts but not this one.
This workaround is fine for me to wait the fix.
Thanks a lot
Workaround :
It seems the problem might be linked to transparent items like background.
As explained in the above thread :
According to the bug report the nVidia driver is freaking out and creating too many events, which causes an event buffer in Xorg to overflow. It works OK with the older Xorg, though.
So the temporary solution is to downgrade 3 packages.
Install the tool to downgrade
> yaourt -Sy downgrade
Downgrade
Note the item number can change
> downgrade xf86-input-evdev
Hit "s" key
Choose 2 (xf86-input-evdev-2.6.0-2-i686.pkg.tar.xz)
> downgrade xorg-server
Hit "s" key
Choose 1 (xorg-server-1.9.4.901-1-i686.pkg.tar.xz)
> downgrade xorg-server-common
Hit "s" key
Choose 1 (xorg-server-common-1.9.4.901-1-i686.pkg.tar.xz)
Be carefull : don't update these 3 packages when updating your system (pacman -Syu) since it is not fixed.
Last edited by shefla (2011-04-27 22:36:37) -
No sound after installing geforce 210 video card in hp pavilion a1430n
I've seen the advice about changing bios sound device setting from auto to enabled, but there is no sound device choice in the bios of this model.
Control panel>sounds shows "no audio device installed"
I installed this new geforce 210 video card (in addition to existing GeForce 6200) in order to support 3 monitors. I previously had a Geforce 5200 FX installed for this purpose, but it died. The new 210 has HDMI output. Some of the responses in this forum credit this as part of the problem.
I only need audio out of the headphones on the computer - not using any external audio like speakers, monitors, etc.
IN device manager, under sound, video and game controllers there is a long list
Audio Codecs
Legacy Audio Drivers
Legacy Video Capture devices
Media control devices
4 entries of NVIDIA High Definition Audio - which all seem identical looking at properties
Video Codecs
All show working properly
Any help or advice greatly appreciated
E de T
This question was solved.
View Solution.Hi,
Installing a new video card can disable the on-board sound chip so check the following.
Shut down the PC. Tap away at f10 as soon as you press the power button to access the Bios Menu - the option you want is most likely under the Advanced Tab. Look for an entry titiled 'Onboard Audio'. If it shows as Disabled, navigate to it using the arrow keys, hit enter, use the arrow keys to select 'Enabled' and hit enter again. Press f10, select 'Yes' or 'Ok' and hit enter to save the change.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience -
Problems with Geforce 210 on Thinkcentre M58
Hi all,
as part of the upgrade process of my Thinkcentre M58-7360 I bought a Geforce 210 based video card:
http://www.zotac.com/index.php?page=shop.product_details&flypage=flypage_images-SRW.tpl-VGA&product_...
At the boot the system emits two "beeps" and then Windows seems to normally load.
I said "seems" because during the whole boot there is no video signal and the monitor stays black.
I have also played a bit with BIOS settings (explicitely set the PCI express card as primary video adaptor) but no change.
Last, if I remove the card everything works fine again.
How can I troubleshoot the issue?
P.S.: I preferred an Nvidia over AMD solution hoping that it would have worked out of the box, but unfortunaltely it's not the case.I should test your way for using remote desktop but on my PC (8381-CTO) the screen keep staying black *after* I've installed the driver. The problem seems to come from audio drivers. I have to (and I had to) upgrade about one undred PC and in some PC I've not experienced any problem while on other PCs the only way to stop troubles is to remove the graphics card (zotac geforce 210).
Any suggestion? -
Windows screen of death when installing iTunes 8
I'm an XP user and have been using iTunes happily for some time. However, I encountered a problem in installing 8. Initially, I had the invalid F: error, but when I plugged in my external drive the message disappeared and the install began normally. Then I suddenly got the Windows screen of death and everything locked up. I re-booted and tried again; I removed the earlier version of iTunes; I went through regedit and failed to find any reference to an F: drive in shell folders (indicated in a previous thread) and am at a loss what to do. Can anyone help?
Use XP Installation disk with SP2 or SP3 included to fix the BSOD.
Simple your XP installation disk is outdated and cause troubles with latest hardware. -
MSI GeForce 210 not post in Sapphire A9RX480 mobo?!
This is a bit nuts. The MSI card is GeForce 210-MD512H:
http://www.msi.com/product/vga/N210-MD512H.html#?div=Specification%22
...witch is basicaly fanless budget MSI GeForce 210 with 589/1024MHz clocks and 512MB DDR2 ram. All in all a budget card to do the work required and that it is. I never expect playing Crysis on it... maybe SoF2... lol!
However I wanted to use it in my Sapphire "Grouper" A9RX480 mobo (that is ATI chipset RX480-450 for SB) and it refuse to post. When I plug there my old good PNY GeForce 7800, then (even w/o the external power cable connected - DOS only, true) everything seems working out nicely!
Now that is a bit insane. Any suggested bios settings to make the card work? The mobo is fine, memtest passed all tests and never had a problem with it...
Yes, it is claimed to be 16x PCIEx speed... shall I try 8x? Or what should I do? The card is also tested in another computer and it is working nicely there...!Oooops, I'm sorry. When way more powerfull and way more PSU demanding 7800 GTX works fine, then I never even mind that any other information is necessary, but whatever. Here we go:
Board: Sapphire A9RX480 "Grouper"
Bios: oldest and even latest official version available tried, even moded version: http://ax2.old-cans.com/grouper - still same problem!
VGA: MSI GeForce 210-MD512H ( http://www.msi.com/product/vga/N210-MD512H.html#?div=Specification )
PSU: Enermax 620W Liberty
CPU: Opteron 148
MEM: Mushkin Enhanced DDR400 PC3200 (can do 2-2-2-5 :D - memtest fine)
HDD: none
COOLER: Zalman CNPS 9500 Led
OC: none
OS: none
It is just a mainboard, PSU and floppy sitting on chair near monitor (Eizo F35 Flexscan) for testing... Nothing else.
Tried 8x settings in the PCIE Bus Width, no difference :(
Some BIOS settings are really interesting - how about these?
LTD Configuration - Enabled
Upstream LTD Bus Width - 16bit
Downstream LTD Bus Width - 16bit
LTD Bus Frequency - Auto (1GHz, 800MHz, 600MHz, 400MHz, 200MHz)
(I know, this have more to do with the CPU memory controler that GFX card, but who knows?)
PCIE GFX Core Payload Size - 64Bytes (32Bytes, 16Bytes)
PCIE GPP Core Payload Size - 64Bytes (32Bytes, 16Bytes)
NB-SB Port Configuration - Default (Enhanced)
PCI-E GFX Link Width - x16 (x12, x8, x4, x2, x1)
Assign IRQ For VGA - Enabled (Disabled)
...any suggestions? Tried 32Bytes (for the PCIE GFX Core Payload Size|PCIE GPP Core Payload Size settings), but no change. Eg. NO POST with this MSI card...
Additional info about the card: it is MSI GeForce 210-MD512H, on the PCB is near the heatsink and PCIE connector:
"V201" "VER: 1.1" and "Product of China" and near the "no trash" symbol is "D33008"
From the bottom side, there is a big letters "N1996" after a "Nike" checkmark and at the end of the PCB, some probably manufacture info:
APCB M3 94V-0
RU 0942 E230435
E129N4774BB
Bought the card from friend, who replaced it with faster one. Tried with another computer, where it worked just fine (IIRC Gigabyte mainboard, but not sure about it) ...
Is there any bios fix for this card that help me out? -
NEED THE 64-Bit DRIVER SOFTWARE FOR MSI GeForce 210 N210-D512D2
Does anyone have 64-BIT version of MSI GeForce 210 N210-D512D2 Driver Installation? I have tried the 32-bit version, but it didnt work because I am running 64-bit
install those:
http://www.nvidia.com/object/win7-winvista-64bit-280.26-whql-driver.html -
I have a MSI geforce 210 that i recently installed and it keeps overheating and shutting down my system. The fan is running and the case cover is off and it still overheats. Any suggestions?
Thank
AndyI've got 2 of those cards. The one that comes with a dinky little toy fan doesn't overheat as long as you don't run intensive graphics. If you do, it cooks and I haven't figured out how to give it additional cooling yet.
The 'Silent' version comes with a massive heat sink but no fan which is worthless as it is upside down and apparently the manufacturers haven't figured out the old conduction, convection and radiant heat rules yet. The old devil called heat rises, going right back into the GPU and only a little radiant heat getting carried away from things. Anyway, if that is the card you have, grab some zip ties and strap and hefty little CPU fan to the heat sink, eating 2 more card slots in the process. It will run very cool and happy. -
[SOLVED] Driver for Nvidia Geforce 210
Hi guys. I'm having some trouble searching the proper video driver for my system. I need the nvidia driver for my Geforce 210.
The wiki says: "For GeForce 2/3/4 MX/Ti series cards [NV11 and NV17-NV28], install nvidia-96xx package, available in the AUR. " , but is there any way to avoid using AUR?
I've tried downloading the propretary driver from Nvidia' site and couldn't install it. So i'm thinking about the open drivers: is Nouveau a good choice in your opinion?
Thanks for reading!
Last edited by Issam2204 (2013-05-11 13:11:45)Issam2204 wrote:I thought 2 meant 200. So what do you think i should install? Now i'm even more confused.
run the following command & post the output here:
lspci | grep VGA
if you REALLY do mean Geforce 210 you should see something like this (as I have a Geforce 210)
┌─(t0m5k1@b0x)-(1131/pts/3)-(03:02pm:10/05/13)-
└─>(%:~)
└─>> lspci | grep VGA
02:00.0 VGA compatible controller: NVIDIA Corporation GT218 [GeForce 210] (rev a2) -
Hp 210 windows update not working
HP 210 1032 Cl Hard drive failed. Machine is appx. 5years old and the recovery CD's were from tht same time. Installed new WD 320 GB hard drive and used recovery CD's to reinstall Win 7 32 bit starter. All is working well EXCEPT windows update. Keeps coming back with message "service not started", etc. Have tried downloading new drivers from HP for the Intel atom, etc---but still no luck. Any guidance appreciated!
Hi @ned-m
I regret that the link did not resolve your difficulty.
What was the results when you tried resetting the updater per the document in the link?
Did you run MS Fix It, if so what was the result.
Here is a link to Troubleshoot problems with installing updates . If none of the above has helped, I would try doing a Windows repair.
I would try a Windows repair or reinstall your Windows. Performing an HP system recovery (Windows 7)
If you are still having a difficulty,I suggest contacitng HP support for assistance.
Please call our technical support at 800 474 6836. If you live outside the US/Canada Region, please click the link below to get a support number for your region.
World Wide Phone Support
Best of Luck!
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping! -
Drivers for NVIDIA Geforce 320m (Windows 7).
I've got my new MBP 13", but i don't have a cd with the bootcamp drivers for the video card, because I've lost my recovery DVD. So i'm seeking help with that. I wonder where can i get these drivers, because NVIDIA ones, even beta, not supporting this chip yet. Maybe i can get a recovery dvd iso or dmg somehow. I've got bootcamp 3.0 and 3.1 update installed on my windows machine, but still no luck, because the 3.1 version is dated mid january and my MBP is mid 2010.
Message was edited by: lazycoderSomewhat related, my 13" MacBook Pro with BootCamped XP freezes when I open up BootCamp from the control panel and move the brightness slider/window around. To fix this, I'm trying to install the newest NVidia drivers.
With a NVIDIA GeForce 320M display card installed, trying to install the newest NVidia drivers on XP, I continuously get an error say "The NVIDIA Setup program could not locate any drivers that are compatible with your current hardware. Setup will now exit."
One way to solve this, as suggested by someone on another forum, was to install the drivers manually, and at the 99%~100% during installation, when it shows the error message "Your installation cannot continue, will revert back to your old display drivers when you click OK" at which point I don't press OK, but immediately hold the power button down for 5 seconds, after I re-boot, my new drivers work fine.
Except,
I can't control brightness from the control panel's bootcamp slider, nor keyboard shortcuts, it's continuously 100% brightness.
I've been working on this problem for 2 days, and I can't yet properly install the new NVidia drivers into XP. Any advice would be greatly appreciated. -
No sound after installing Dynex - 400-Watt ATX CPU Power Supply & PNY - GeForce 210 1GB DDR2 PCI Ex
I installed both pieces and everything works fine but the onboard sound. my USB headset gets audio but no sound comes from the lime green audio jack from the back of the PC. when my USB headset is not plugged in the audio icon at the bottom right corner says "no audio devices installed"
any solutions?
EDIT: i have an a6120n HP
This question was solved.
View Solution.Hi,
Tap away at f10 as you start the PC to enter the bios menu. Check if Onboard Sound has been disabled here as this can happen when installing a new graphics card - if it is disabled, use the arrow keys to select Onboard Audio, hit enter, use the arrow keys to select Enabled, hit enter, press f10 to save the change, use the arrow keys to select 'Yes' and hit enter.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience -
Do I need to update drivers and anything else
I now have window 7 as my op systemI know your solution! This happened to me. Look on your keypad. (mouse) In the top lefthand corner there should be a little circle. If it's glowing (I think orange) it is locked. Press the dot gently with your hand (it may take a few tries) and it should stop glowing. Now your computer should be as good as new!
Hope I helped,
Maddie -
Nokia + WIndows Phone 7 = Death
Nokia i will not purchase for your smartphones on Windows 7
GOOD BY NOKIA FOREVE!!!!
Nokia - You are very stupeds...
nokia we want good working devices and not cheat!!!
The modification C6-00 to C6-01 it's only fix your errors... wy we must pay again for your errors???Luvbeers wrote:
Looking forward to the transition! Symbian is rubbish. When can I update by N8 and C7-00 with Windows Phone 7?
If you realy whant a Windows Phone 7 - go to garbage collector and take it... It's realy best place for OS like WP7... I say it as developer and as user...
WP7 - too much get resources, too fool unusability UI, and nothing to customize...
And no multi-tasks and other features that already we have on Androind (and even Symbian)!!!
nokia we want good working devices and not cheat!!!
The modification C6-00 to C6-01 it's only fix your errors... wy we must pay again for your errors???
Maybe you are looking for
-
PayloadZipBean - Unzip not working
Hi, Let me explain my scenario first, it is simple but not properly explained in many blog.. I need to fetch a Zipped file( Input.zip), unzip it (contains a Input.xml file ) & map, send it to another file server. In my Sender CC I have added the foll
-
Im stuck in a migration from PC to Mac Book Pro . Help!
It just stopped with 21 hours to go and wont reconnect. Ive rebooted the PC and iMigration Assistant but it just says 'waiting for Mac to connect' but Mac has no controls at this stage because its a new machine.
-
Hi, is it possible to create a submit button in the middle of the form to add data to a repeating table (That repeating table would add an item to a list).
-
Excise modvat accounts not defined for GRPO transaction and excise group
Dear All, as per your suggestion i have activated excise Group and series but still showing below error "Excise modvat accounts not defined for GRPO transaction and 64 excise group" Kindly Suggest...................... Regards Vinay
-
Why does 1 speaker crack when i click on different items (not all) after hp/windows updates?
After installing several updates for Windows 7 & HP g72010nr at the same time, 2 problems have occured. 1 speaker cracks real loud when I click on different items (not everything) AND when running DVDs there are ripples all throught the movies. It's