Generate new interface and camera

i have installed niimaq 251. How do i create a camera that meets my specs?. the ones i see, the fields are
grayed out and can not be modified. How can i enable grayed out fields in the camera file?....
My camera is parallel interface and uses 12 bits. I can not change these in the camera files i open.
Habib

Habib,
If you can not find a camera file for your camera that ships with the IMAQ driver, try looking at out camera advisor for any support we may provide for the camera:
http://sine.ni.com/apps/we/nipc.specs?action=search&asid=1102
This will incude Camera Files, Support Files, Cabling etc...
If you are unable to locate the file for your camera, we typically will attempt to create one in house. You will need to fill out the attached questionnaire and return it to [email protected] (IMAQ/Motion). We will also need the timing diagrams, pinouts and any other instructional information from the camera. It is also benefical if you can send in the camera so we can verify the file works properly. Once our engineers have more info ont eh camera they can give you a time
line for completion.
I hope this helps!
Best Regards,
Chris D.
NI Applications Engineer
Attachments:
Digital_Camera_Questionnaire.xls ‏384 KB

Similar Messages

HT5622 I was setting up the new IOS and came to the point where I needed my Apple ID and password

I was setting up the new IOS and came to the point where I needed my Apple ID and password. I had to go and change it before proceeding, now I can't get back to the setup. Can you tell me how to go back and finish the setup?

Settings > Store > Sign Out.
Sign in with the correct ID.

The new Ipad and camera connection kit with Sony A65 RAW

Hi,
I recently purchased the "new ipad" with camera connection kit. I'm shooting photos in RAW format with Sony A65 and I have succesfully transferred them into my Ipad. The problem is that none of the applications such as Snapseed, Photoforge2, etc. will display the full 24 megapixel image from the RAW file and will instead show small preview.
It is indicated in support pages of these applications that there should be support for IOS Raw engine supported RAW files with full size. Can someone indicate me what RAW formats are supported by IOS 5.1 and whether support for Sony RAW files will be added.
The same problem persists with 16 megapixel images from Sony A55.
Thank you in advance.

Thank you, David, but actually your answer is not helpful. As I explained in my opening message, I am interested in buying and using an i-Pad while on a trip in Spain, where I will not have access to a computer, other than, perhaps, one at the Apple Store where I might buy the i-Pad.

Brand new today and camera doesn't work

The front facing camera works fine, although a little slow. However when using the main camera I'm left staring at a blank screen, if I put the torch on it goes off a couple of seconds, and if I take a picture (of the blackness) it either freezes or says 'unfortunately camera has stopped working' I've literally owned the phone for 5 hours and it doesn't work, any help? I've tried going to settings apps all camera and closing etc but no luck.

Hi Chimb0,
Welcome to the community! Since you're new please be sure that you have checked out our Discussion guidelines.
I suggest you try clearing the data from the Camera application.
Menu > Settings > Apps > All > Camera > Clear Data.
If this does not work, then I suggest that you take the handset back to the place of purchase.
I apologize for any inconvenience this may cause.
- Official Sony Xperia Support Staff
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

Configuring New Interface and NAT on Cisco 1900 Series Router.

Hello Cisco Team,
am asking for advise on how to how setup NAT rules and overload on my 2nd interface on my cisco 1900 series router,am not sure where am getting it wrong.
my router has 2 interface, interface one has IP address 10.5.5.5X and plugs into my ASA firwall and into my switch and works just fine.
i have just configured my second Interface with a new IP 172.16.0.X- i want to NAT my new IP address to our public IP address which is 41.77.X.X
my configuration so far are as follows.
GigabitEthernet0/0 172.16.0.X YES manual up up - Not working
GigabitEthernet0/1 10.5.5.X YES NVRAM up up- this works fine
GigabitEthernet0/0/0 41.77.X.X YES NVRAM up up

Hello Jon,
Thanks for your feedback, my router configuration are as follows.
interface GigabitEthernet0/0
description WL2504
ip address 172.16.0.2 255.255.254.0
duplex auto
speed auto
interface GigabitEthernet0/1
description WAN
ip address 10.55.55.2 255.255.255.252
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface GigabitEthernet0/0/0
description LINK TO CLT INTERNET
ip address 41.X.X.130 255.255.255.248
ip nat outside
ip virtual-reassembly in
duplex full
speed 100
media-type sfp
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list 1 interface GigabitEthernet0/0/0 overload
ip route 0.0.0.0 0.0.0.0 41.X.X.129
ip route 41.X.X.136 255.255.255.248 10.55.55.1
ip route 192.168.0.0 255.255.255.0 10.55.55.1
access-list 1 permit 10.55.55.0 0.0.0.255
access-list 1 permit 192.168.0.0 0.0.0.255
access-list 1 permit 192.168.1.0 0.0.0.255
from the router interface  interface GigabitEthernet0/0- I will connect it to my wireless Controller WL 2504

Elements 11 accepts no *.arw files even after new installation and camera raw modul 7.4. Under open files as Camera Raw the *.arw file is listed.

After trying all options provided by Adope I cannot open *.arw files under Elements 11.

You need camera raw 8.3 for your camera. It is only compatible with PSE12 or PSE13. Alternatively, download and install the free Adobe DNG converter to convert your raw files to the Adobe universal Raw format and the files will open in all versions of PSE (keep your originals as backups and for use in the camera manufactures software)
Windows download (.exe file) click here DNG Converter 8.3
Mac download (.dmg file) click here DNG Converter 8.3
You can convert a whole folder of raw images in one click. See this quick video tutorial:
You Tube click here for DNG Converter tutorial

Installed new iOS and camera won't work

I have been successfully using my iphone5 camera for over a year. After downloading iOS 7.0.4 about 2 weeks ago, my iphone5 camera is useless. When I select 'camera', my screen comes up either totally black or, other times, it shows an indistinguishable blurry image that is frozen on the screen. Does anyone have a solution for this problem. The phone's camera was working perfectly before this new iOS was installed.

Try a reset: hold down the home button along with the sleep/wake button until you see the apple, then let go. (No data loss)

I need a help to generate new file

Hi Guys
I need your help. I have two text box in my form, the first one takes the file name to read, and then when user type in another file name in the second textbox, result should be saved as a typed file name in the same path.
What I really want to do is, when the file is exist already (for instance, I'll name it as result.txt), my program scan through the result.txt file and append the new data at the end of the file. But result.txt file doesn't exist, it has to generate new file and save the data into the new one. I think I need to implement these in the OpenFile1() function, but I dont' know how.
Does anybody have idea to solve this?
private void saveFile() {
textArea.append("SAVE FILE\n---------\n");
if (openFile1())
     try {
          outputToFile();
catch (IOException ioException) {
          JOptionPane.showMessageDialog(this,"Error Writing to File",
               "Error",JOptionPane.ERROR_MESSAGE);
private boolean openFile1 ()
     // Display file dialog box
title=textfield1.getext();
path=fileName_in.getPath();
     File file_out = new File(path, title);
if (fileName_out == null || fileName_out.getName().equals("")) {
     JOptionPane.showMessageDialog(this,"Invalid File name",
               "Invalid File nmae",JOptionPane.ERROR_MESSAGE);
     return(false);
     else {
try
boolean created = file_out.createNewFile();
if(true)
fileOutput = new PrintWriter(new FileWriter(fileName_out));
return(true);
else
catch (IOException exc) {
System.err.println("# Error: " );
private void outputToFile() throws IOException
// Initial output
     textArea.append("File name = " + fileName_out + "\n");
     //process();
     // Test if data exists
     if (data != null)
     Date now = new Date();
DateFormat df = DateFormat.getDateInstance(DateFormat.SHORT);
String s = df.format(now);
//long nowlong=now.getTime();
fileOutput.println(s);
fileOutput.print(fileName_in.getName() +" of slope value:" + slope);
textArea.append("File output complete\n\n");
     else
textArea.append("No data\n\n");
     // End by closing file
     fileOutput.close();
Thank you so much!

There's a lot of unnecessary code there, and anyway it isn't formatted in a readable way so I am not going to look too closely at it. But if you want to append to the file if it already exists and create the file if it doesn't, then all you need is this: fileOutput = new PrintWriter(new FileWriter(fileName_out, true));Note the "true" parameter there which (if you look in the API documentation) says that new data will be appended at the end of the file.

Generating new Request number

hi frends i was working with smartforms on develpment.i had made sme changes in the code and then save it.system asked for the request no.by mistake i had not gone for "own Request" and click OK for the default Request value displayed there. The changes i have done are not reflecting into the print preview(for which i had made changes).Is this because i had not created new request?how to slve it.can i generate new request and then see the changes in the print preview.
I want to see the changes in the same client and on the same server.
I am doing changes in the print format of the WORK ORDER.

thnx MAX....frend now i have created my new request saved the smart form and activted.but still it is not working....i have also tried to comment out the all code and then see the result..still it is not effecting the print preview.
I have a smartform designed earlier.There is a text elemet "PAN no of vendor" i clicked on it then system took me to a code. the ouptut parameter shown there is "FOR_PROJ". i have made the value of this FOR_PROJ=12345678. and commented out the rest of code.still it is not showing this value in actual print preview.
while creating PO with ME21N if we write anything under "your ref" field under "communication" tab then the data in your ref is displayed in the preview.
what shoud i do. i am very new to ABAP and smartforms.but i have to solve this

What interface and monitors are you using?

I need to buy a new interface and monitors. I'm interested in the Native Inst. Audio Kontrol 1, the Line 6 Toneport UX2, and the Emu 0404 USB 2.0. I'll probably go with the Blue Sky Media Desk monitors.

hey there NIKKO,
i use a MOTU 828 MKII w/ a MOTU MIDI Timepiece AV & Alesis M1 MK2 Active monitors. it's not all about the hardware/software.... check out Auralex & Auralex University. a great site w/ info on room accoustics & how they can afffect your recordings & mixes. see this link -http://www.auralex.com/
it's about making music & having a good time doing it. & it is a good time on a Mac!!! good luck w/ whatever you get.

How can I find my playlists in this new interface? And then, how can I transfer newly purchased songs to a playlist?

how can I find my playlists in this new interface? And then, how can I transfer newly purchased songs to a playlist?

iCloud does not store messages for you to see/access at icloud.com. It does back up messages so you can restore your iPhone if it ever needs to be reset to factory default. A backup is an image of all your data on the iPhone, and if you delete some messages, then they won't be part of any further backups.
If two people use the same iCloud account, then their devices are kept in sync, just like a single user's multiple devices are kept in sync. It's usually a good idea to have separate accounts for two people, since it's rarely the case that they want each phone to be an exact replica of the other.
Your iphone syncs contacts, events, camera roll, and many other things without the use of a computer.
Read about icloud here... http://www.apple.com/icloud/

Sum of LineCount Including Groups and Detail Data On Each Page Used To Generate New Page If TotalPageLineCount 28

Post Author: tadj188#
CA Forum: Formula
Needed: Sum of LineCount Including Groups and Detail Data On Each Page Used To Generate New Page If TotalPageLineCount > 28
Background:
1) Report SQL is created with unions to have detail lines continue on a page, until it reaches page footer or report footer, rather than using subreports.    A subreport report is now essentially a group1a, group1b, etc. (containing column headers and other data within the the report    with their respective detail lines). I had multiple subreports and each subreport became one union.
Created and tested, already:
1) I have calculated @TotalLineForEachOfTheSameGroup, now I need to sum of the individual same group totals to get the total line count on a page.
Issue:
1) I need this to create break on a certain line before, it dribbles in to a pre-printed area.
Other Ideas Appreciated:
1) Groups/detail lines break inconveniently(dribble) into the pre-printed area, looking for alternatives for above situation.
Thank you.
Tadj

export all image of each page try like this
var myDoc = app.activeDocument;
var myFolder = myDoc.filePath;
var myImage = myDoc.allGraphics;
for (var i=0; myImage.length>i; i++){
    app.select(myImage[i]);
    var MyImageNmae = myImage[i].itemLink.name;
    app.jpegExportPreferences.jpegQuality = JPEGOptionsQuality.high;
    app.jpegExportPreferences.exportResolution = 300;
       app.selection[0].exportFile(ExportFormat.JPG, File(myFolder+"/"+MyImageNmae+".JPEG"), false);
    alert(myImage[i].itemLink.name)

HT1695 I know nothing about how to use my new ipod and when reading the little bit of information in the folder that came with it, all I can do is turn it on, but it just powers down after a few seconds. How do I work this thing?

I know nothing about how to use my new ipod and when reading the little information that came with it, all I can do is turn it on. Then in a few seconds it goes black, never having brought up a screen to do anything! Help! What do I do to get this thing going?

You might consider connecting it to the charger and charging up the battery overnight.
Please Get the iPod Touch User Manual for iOS 5

I am new to iMovies. When I make a video using the mic and camera in my Macbook Pro, the audio and video are not in synch. Very annoying. How can I fix this?

I am new to iMovies. When I make a video using the mic and camera in my Macbook Pro, the audio and video are not in synch. Very annoying. How can I fix this?

DVD drives read the bottom of the disk, not the top. Smooth out the paper & try again.

Premiere project opened - closed sequences and generating new peak files

Hey guys,
I'm working on a big project, which resides on our Drobo. I have been sorting clips and working in sequences for the last couple days now. All media was loaded fine, and peak files were generated.
When I went to open the project this morning, all of the sequences I had been working on (accept for one) had been closed, instead of opening up like how I left them. Further, Premiere is now generating new audio peak files for the project, which is taking forever. Finally, it took 25 minutes to load all of the clips (about 800 or so). They finally finished loading, but I can't start working until the peak files are finished. All in all, i've been at work for 1 hour and still can't work.
Basically, why didn't Premiere open the project as I left it last night? Closed sequences, slow load time, generating new peak files?
I'm working with footage from RED, Sony FS700, GH4, and GoPro.
My system:
Creative Cloud
Premiere Pro 8.0.1
Windows 7 (64 bit)
Intel 3770k
Quadro k4000
16 gb ram
256 gb SSD (System)
256 gb SSD (Render files)
5.39 TB Drobo via USB 3.0
Thanks,
Dan

>Drobo via USB 3.0
Did you by any chance unplug/replug your USB drive?
Have you gone into Windows and "locked" the drive letter?

Generate new interface and camera

Similar Messages

Maybe you are looking for