Get printer out of mfg mode

Printer: Photosmart 2575 All in one
Somehow I managed to get my printer into MFG-mode. Most important functions seem to work, but I prefer the "normal" mode. Switching off the printer for some time (several times) does not work. Re-installation: no effect.
Can anyone tell me how I can reset this?
Thanks,
jowe
This question was solved.
View Solution.

Hi Everyone,
There are several different solutions provided depending on the printer model. The information required to fix the issue on this thread is a reset which should only be given under direct instruction of a HP tech support representative. They should not be done lightly!
Refer to Printer Resets: What You Should Know:
There are an increasing number of posts in this forum and elsewhere in the internet with the steps to do a resets on different printers. The reset itself will sometimes fix problems, so the reset is not the issue.
Some resets require you to enter button combinations to open special menus on your printer that you were never meant to access. These special menus are used by the developers and support personnel for debugging issues, but they are not meant for untrained users and can have unintended results. One wrong button push and you no could no longer have a printer, but instead a pricey paper weight. To top it off, if you do happen to "brick" the printer this way, it is considered customer induced damage, and voids the warranty automatically. These resets are only meant to be given out and used as a last resort, and under direct instruction of a HP tech support representative. They should not be done lightly!
Please check your private messages, and let me know if the steps provided resolve your issue?
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as "Accepted Solution"

Similar Messages

Printer showing MFG mode - unable to get it out of MFG mode

I have a HP 3545 all in one printer On switching on the power inlet, MFG mode comes up on the display in printer. I cannot get it out of MFG mode by using Home, Back, Double Home . Please let me know what needs to be done to get it out of MFG mode

Welcome to the forums @dtalukdar !
I read about your Deskjet 345 being stuck in MFG mode. I noticed that the reset you were trying did not help get the printer out of the MFG mode as well.
I would suggest calling us directly so we can discuss what your printer options are with HP.
Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
Best wishes!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

I tried to update my ipod touch software update by syncing with itunes and now its in recovery mode? Is it possible to get it out of recovery mode? if so, then how?

I tried to update my ipod touch software by syncing with itunes and it put the ipod into "recovery mode". Seems like the only option is to restore? Is there a way to get it out of recovery mode?

No.
Once the Device is asking to be Restored with iTunes... it is too late to save anything...
To minimise loss... Connect to iTunes on the computer you Usually Sync with and Restore from the most recent Backup...
http://support.apple.com/kb/HT1414
Restore from Backup
http://support.apple.com/kb/ht1766

TS1369 my "home" computer for my ipad is no longer working, how can i get my ipad recognized on new comp to get it out of recovery mode?

The original laptop i used to start my ipad broke so i have a new laptop. I cannot upgrade my ipad with the new laptop and i cannot get it out of recovery mode cuz my laptop is not recognizing the ipad. How can i get my laptop to recognize the ipad so i can get it out of recovery mode?

Hey Dpcupcake,
If you can not get past the sign in screen on your iPad, you will need to use the steps in this article to recover use of your iPad -
Forgot passcode for your iPhone, iPad, or iPod touch, or your device is disabled - Apple Support
Thanks for using Apple Support Communities.
Happy computing,
Brett L

Not getting print out of PO

Dear all,
I am not getting print out of PO. In the message out put, the config ( NACE , MN04 ) and as well as all setting are correct. in FURTHER DATA tab, the despatch option id 4 : Send immediately ( when saving the application) ; but it is not generating any spool request for print out. i have checked in SP01 and SP02 , but I could not find out any spool request. More interesting, with the existing config and message setting , we were getting print out till one day ago but presently it is not working.
Hoping for corrective solution.
Regards,
Partha

Hi,
check t.code SPAD and involve Basis Consultant.
Also check NACE t.code for Program, std form,routine, medium
Note:
Customisation steps for Output of Purchase Order
1. Condition Table
SPRO > Material Management> Purchasing -> Message -> Output Control->Condition Tables->Define Condition Table for Purchase Order
Select:
Purchasing Doc. Type,
Purch. Organization,
Vendor
2. Access Sequences
SPRO -> Material Management-> Purchasing -> Message -> Output Control->Access Sequences->Define Condition Table for Purchase Order
3. Message Type
SPRO -> Material Management-> Purchasing -> Message -> Output Control->Message Types->Define Message Type for Purchase Order
4. Message Determination Schemas
4.1. Message Determination Schemas
SPRO -> Material Management-> Purchasing -> Message -> Output Control->Message Schema->Define Message Schema for Purchase Order-> Maintain Message Determination Schema
4.2. Assign Schema to Purchase Order
SPRO -> Material Management-> Purchasing -> Message -> Output Control->Message Schema->Define Message Schema for Purchase Order-> Assign Schema to Purchase Order
5. Partner Roles per Message Type
SPRO -> Material Management-> Purchasing -> Message -> Output Control-> Partner Roles per Message Type ->Define Partner Role for Purchase Order
6. Condition Record
Navigation Path: SAP Menu-> Logistics -> Material Management -> Purchasing-> Master data->Messages-> Purchase Order-> MN04-> Create
Now you create PO (ME21N) and save it. Go to ME22N and print the PO by giving output type.
Regards,
Biju K

My iPhone 3GS 16gb, is stuck in restore mode, downloaded and tried to do a restore multiple times. Keep getting an error The iPhone "iPhone" could not be restored. Unknown error occured (-1). Cannot get it out of restore mode, keeps rebooting!

My iPhone 3GS 16gb, is stuck in restore mode, downloaded and tried to do a restore multiple times. Keep getting an error The iPhone "iPhone" could not be restored. Unknown error occured (-1). Cannot get it out of restore mode, keeps rebooting!
I have tried to hold the "home" and "power" button to reboot
I have tried powering it off
I have tried, to unplug the cable, hold the "home" button and then plug it in.
Can't check the SN or warranty, cause it is stuck in restore mode.
Is the hard drive gone? Should there be something replaced.

http://support.apple.com/kb/TS3694#error1
Error 1 or -1
This may indicate a hardware issue with your device. Follow Troubleshooting security software issues, and restore your device on a different known-good computer. If the errors persist on another computer, the device may need service.
Usually this is caused by your antivirus or firewall blocking iTunes access to the Internet. It can also occur if the phone is jailbroken or if the computer you are using was ever used to jailbreak an iDevice.

My iphone is in recovery mode and i cannot restore it with itunes on my macbook or my pc. how can i restore my iphone 4s? or at least, how can i get it out of recovery mode?

i tried to restore my iphone 4s because it kept saying "searching..." for service so i decided to restore it, after having already reset all network settings, and after trying to restore all settings. still, it only said "searching..." for service. finally, i tried to restore my iphone. when using my macbook, 3/4 through i recieved a message to update my itunes software. i had to close itunes for the update. when i closed itunes, the iphone restore was in pprogress and having to close the program put my phone into this "recovery mode" with the icon of the usb and the itunes disc logo. i also tried updating and restoring the software with my pc which also didnt work. help?

Once the Device is asking to be Restored with iTunes... it is too late to save anything... and you must continue with the Recovery...
kevinpowell1 wrote:
how can i get it out of recovery mode?
Make sure you have the Current Version of iTunes Installed on your computer
iTunes free download from www.itunes.com/download
Then See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once... Be sure to Follow ALL the Steps...
Take your time... Pay particular attention to Steps 3 and 4.
Some users have reported as many as 8 or 9 attempts were necessary before success.
After you have Recovered your Device...
Re-Sync your Content or Restore from the most recent Backup...
Restore from Backup > http://support.apple.com/kb/ht1766
If the issue persists...
Then a Visit to an Apple Store or AASP (Authorized Apple Service Provider) is the Next Step...
Be sure to make an appointment first...

Iphone 5 stuck on connect to itunes screen- if i try and get it out of recovery mode it trys to extract the data and then says the phones memory is full

iphone 5 stuck on connect to itunes screen- if i try and get it out of recovery mode via itunes, it trys to extract the data and then says the phones memory is full- cant seem to get it sorted, any ideas? I have an ipad mini if that helps?!

Hey craigfromsheffield,
I would suggest that you use the following information in order to help you resolve this issue:
If you can't update or restore your iOS device
http://support.apple.com/kb/HT1808
Thanks for using the Apple Support Communities!
Cheers,
Braden

The battery of my 2nd gen itouch drained. when i tried to charge it, it's already in recovery mode. how can i get it out of recovery mode without restoring?

my 2nd gen itouch went to recovery mode after the battery drained. how do i get it out of recovery mode without restoring it? btw, my itouch is not jailbroken and it's on ios4 (don't know which version). thanks!

you can find softwares like recboot that will remove the recovery mode. you can search it on google
http://www.google.com.np/search?q=download+recboot&ie=utf-8&oe=utf-8&aq=t&rls=or g.mozilla:en-US:official&client=firefox-a

How to get ipod out of recovery mode without losing media.

i tryed to update my ipod on another computer and it put it in recovery mode.how do i get it out of recovery mode without losing media.

If this program does not work then you will have to restore.
RecBoot: Easy Way to Put iPhone into Recovery Mode

How do I get ITunes out of compatibility mode?

How do I get ITunes out of compatibility mode?

Try the following document, only be sure that none of the boxes in the compatibility tab are checked (not just the compatibility mode box itself):
iTunes for Windows: How to turn off Compatibility Mode

I was in the process of jailbreaking and updating my ipod and when i was updating it,it went into recovery mode and now i cant get it out of recovery mode so what can i do??

i was in the process of jailbreaking and updating my ipod and when i was updating it,it went into recovery mode and now i cant get it out of recovery mode so what can i do??

Go elsewhere:
Jailbreaking voids the Apple warranty and also means that you will not get any support from Apple, including from this Apple forum. Jailbreaking can't be discussed in this Apple forum.
Unauthorized modification of iOS has been a major source of instability, disruption of services, and other issues

When i connect to itunes its saying its in recovery mode on my nano. how do i get it out of recovery mode so i can download music

when i connect my nano to itunes it says i am in recovery mode. it told me to restore so i did and it still is in recovery mode and i lost everything on my ipod. what do i do to get it out of recovery mode?

Reset, can sometimes exit Recovery Mode if nothing is wrong with your iPhone. If there is problem only exit is to connect to iTunes and click the Update or Restore button that iTunes offers you.

TS1702 I purchased the app Word Lens but cannot get it out of demo mode.

I purchased the app Word Lens but cannot get it out of demo mode.

Hi bellref, I'm one of the creators of Word Lens.
Once you download Word Lens for free, you can purchase language packs by tapping the language bar at the top of the screen. We currently offer Spanish, French, and soon Italian. If those are not on your list, let us know which you'd like to see.
You can also chat with us at [email protected], or contact us on twitter!

Need help for multipule handling unit get printed out

Hi ,
I have multipule handling unit in case of issuing the output for selected multipule handling unit using output type . I am getting one handling unit to be printed out . Please can u suggest any configuration is recquired to get selected printed out all the select handling assigned to output type
Any configuration is recquired to get printed out .
process followed .
give DO no for vl02n (tcode) and then pack from the menu we get handling unit need to be selected 3 or 4 handling unit then go to extra's and select output given here output type and save it .Then in nace i got only one handling unit.

You can use the t-code VL74 for printing handling unit output.

Get printer out of mfg mode

Similar Messages

Maybe you are looking for