Getting direct access to Internet is sporadic.

When I get the "Firefox cannot find this site" screen -- or words to that effect -- if I 1) highlight the address, 2) click enter, and then 3) click on "Try again," I can usually then connect. Sometimes I have to do this twice. Once in a while, it doesn't work at all. This happens, again sporadically, even with your own site, but not just yours but virtually any other site I might be trying to access, e.g.,<pej.org>.

plug it back into your router. Set the DMZ to the ipaddress of your solaris machine.

Similar Messages

How so i get direct Access to the Music/pics stored on NAS

How so i get direct Access to the Music/pics stored on a Buffalo Link Station Live with my iPad without using a App? The NAS is conected with a Router. Privatfreigabe (dont know the english Word) is ok. The iTunes Server on NAS is activated. Nö Problem to get Access from iTunes on PCs.
I just want to use the preinstalled Musik/Photo App to Listen/watch my Music/pics stored on the NAS without losging them on the iPad. Streaming is what i think of.

Have a look at FileBrowser.
https://itunes.apple.com/sg/app/filebrowser-access-files-on/id364738545?mt=8

Solaris 10 : Direct Access to internet

Hi guys !!!
I have a server with Solaris 10. It access the internet by a router, but i want to access in a direct point without the router. When the server is on the router the internet work good, but i plug it on direct point it does not work because he got the "old" ip, the ip used in the router !!!
How can i tell to the server that it needs a new ip !?
Thanks !!!

plug it back into your router. Set the DMZ to the ipaddress of your solaris machine.

Is it possible to get direct access to parallel port pins under Windows NT? What can I do

to get such an access under NT? I found Write to Parallel Port.vi but I can`t open it. The error that occurs is:
resource not found, error occured while loading the vi, labview load error code 8: could not load vi ressources.
This vi is from 1994. Maybe the source of trouble is that I`m using version 5.1.1 or it is a problem with NT. What do you think?

Parallel Port.vi can only be used in DOS-Systems (like Win9x, WinME ;-). NT does not allow writing to parallel port with low level routines. It is more useful to use the digital port that is on most of the DAQ cards.
Some more informations on parallel ports: http://www.lvr.com/parport.htm
In general it seems to be possible. Somebody told me just to use the write port command with the address of the parallel port. Another way seems to be to tell NT to allow direct port access - but I don't know how.
Andreas

How do I stop my search engine from being "hijacked"? I can no longer get direct access to websites.

When I open my Mozilla Start Page, I type in a name or website I am searching and Google provides the usual list of websites. When I click on the website I want it won't open. Instead I keep getting redirected instead of going directly to the website. How I can I stop this from happening?

I would normally wonder if this was a malware problem, but apparently a day or so ago there may have been dns problems relating to google.
Have a look at the thread [http://support.mozilla.com/en-US/questions/773501 Search bar causes browser to be hijacked]
That gives suggestion for
* re-seting the search bar
* sorting out malware
* and if necessary considering changing DNS

Creating SEF URLs and getting directly access to sliding panels

I'm working on a Spry based project that is using SlidingPanels widget with tabs. I usually use "<a href="#" onclick='..." expression to call panels. But the URL never changes as you know. I guess there are some ways to get access to a specified panel by typing URLs into address bar like "main.html?sPanelsLevel1=Id1#Div1&sPanelsLevel2=Id2#Div2...". I tried to use SpryURLUtils but couldn't manage that yet
If I can get these URLs i will use them for creating SEF URLs for google adwords and a sitemap.
Thanks in advance...

Thanks for reply Ben,
Sure, I had a look at this page. But there is no problem with navigate panels with showPanel(PID). I just wanna get the URL to each sliding panel.
Like this...

Can I get direct access to scanlines or rectangles of pixels when creating a video filter?

Maybe I overlooked something, but all the examples in the AE 7 and AE CS3 SDKs that modify the video content, seem to do so through some per-pixel-callback function.
For several applications I have in mind this would be rather slow. Can't I setup a filter to process whole scanlines of pixels or pixel blocks at once? (of course within the region of interest)
More specifically, take the Gamma example. Here's where the actual magic happens:
static PF_Err
GammaFunc (
A_long refcon,
A_long x,
A_long y,
PF_Pixel *inP,
PF_Pixel *outP)
PF_Err err = PF_Err_NONE;
GammaInfo *giP = (GammaInfo*)refcon;
if (giP){
outP->alpha = inP->alpha;
outP->red = giP->lut[ inP->red ];
outP->green = giP->lut[ inP->green ];
outP->blue = giP->lut[ inP->blue ];
} else {
err = PF_Err_BAD_CALLBACK_PARAM;
return err;
This is done for each individual pixel.
I would rather have something where I don't receive pointers to single input and output pixels, but pointers to input and output BUFFERS (and corresponding width, height and stride or pitch) so I can process multiple pixels in one for loop.
Is that possible?

When your entry gets called with cmd == PF_Cmd_RENDER, like here:
PF_Err EntryPointFunc
PF_Cmd cmd,
PF_InData *in_data,
PF_OutData *out_data,
PF_ParamDef *params[],
PF_LayerDef *output
Then params[0] is the "input" layer (it's a built-in param, of type Layer), and output is the "output" layer. Layers include all the pixel data. You can look at the pixel data in memory; here's a macro I use to find a particular pixel location.
#define PIXELPTR(_wld,_x,_y) ((PF_Pixel *)((int)_wld->data + (_y) * _wld->rowbytes) + (_x))
Where _wld is a PF_LayerDef. That macro is for the 8-bit case, by the way.

Windows server 2012 and windows 7 direct access

I am looking for some decent documentation on how to get direct access in windows 2012 to work with windows 7
Can anyone point me the right direction?

Hi, I got success through this
http://syscomlab.blog.com/2012/09/how-to-get-windows-7-to-work-with-directaccess-server-2012/ and this one
http://syscomlab.blog.com/2012/09/directaccess-for-windows-server-2012-guide/ but I'm using NLS in a dedicated server (what is fine for me) but the Win7 client doesn't connect to DA (EDGE server) through internet. I'm using a LAB where WS2012 host acts
as a GATEWAY (using NAT) and for Windows 8 client is working fine but when I try using win7 clients it just doesn't work :(
Server WS 2012 RTM full patched + Win8 Enterprise RTM full patched + Win7 Enterprise RTM ful patched (including the recommended KBs for DA solution)
regards,
Thiago
Thiago Beier Se foi útil marca como resposta! Don´t forget to mark as answer!

Server 2012 Direct Access Single NIC cant get it to work

Hi,
I am having some real issues with setting up Direct Access with Server 2012 and a Windows 8 client, it simply won’t work at all.
First of all I should describe my setup:
I have an internet connection with a static IPv4 address on the external network adapter of the router
The internal network address (the address of the router which has the internet connection) is 192.168.1.1
Server1 (windows 2008 R2 Standard) has a static IPv4 address 192.168.1.2 and has some ports forwarded from the router (443, 25, 80) this server is a domain controller, email server, and has the DNS, DHCP and
certificate services
Server 2 (Windows 2008 R2 standard) has static IPv4 address 192.168.1.3 it has no ports forwarded from the router as it has no services accessed externally, it is used as a file server and print server, backup
domain controller and backup DNS.
Server 3 (Windows 2012) has static IPv4 address 192.168.1.4 and has the Remote Access server role installed along with all the other default features and roles it requires in the setup process.
These servers have all got an IPv6 address which I assume the server has configured automatically, there has been no deliberate configurations made to disable IPv6
I have no UAG or proxy server or anything else to route packets to internal servers. Just this router which has the option for port forwarding (I assume that’s NAT isn’t it?) sorry don’t know much about that
area.
I go through the setup wizard in remote access to configure direct access, in the external URL I have entered da.mydomain.com and created a host A record in my external domain name providers DNS which points
the da record to my external IP address. The wizard creates all the GPO’s, scoped correctly, and applied to a Windows 8 client. The operational status shows its all working and I got green ticks. However, when I connect the client to the internal network it
doesn’t seem to have correctly got the DA settings. I run the following in powershell
Get-DnsClientNrptPolicy
Nothing displays – at all
Get-NCSIPolicyConfiguration
Description
: NCSI Configuration
CorporateDNSProbeHostAddress
: fdd8:dd4a:ea42:7777::7f00:1
CorporateDNSProbeHostName
: directaccess-corpConnectivityHost.mydomain.local
CorporateSitePrefixList
: {fdd8:dd4a:ea42:1::/64, fdd8:dd4a:ea42:7777::/96, fdd8:dd4a:ea42:1000::1/128,
fdd8:dd4a:ea42:1000::2/128}
CorporateWebsiteProbeURL
: http://directaccess-WebProbeHost.mydomain.local
DomainLocationDeterminationURL : https://DirectAccess-NLS.mydomain.local:62000/insideoutside
Get-DAConnectionStatus
Get-DAConnectionStatus : Network Connectivity Assistant service is stopped or not responding.
At line:1 char:1
+ Get-DAConnectionStatus
+ ~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo
: NotSpecified: (MSFT_DAConnectionStatus:root/StandardCi...onnectionStatus) [Get-DAConnect
   ionStatus], CimException
+ FullyQualifiedErrorId : Windows System Error 1753,Get-DAConnectionStatus
I go into services.msc and find that the network connectivity assistant is not started, it wont start either something must trigger it but I have no idea how to get it triggered to start… this might be my only
source of problem perhaps but on a more network level question:
If I have such ports as 80, and 443 (which I assume DA uses in some form with a public IPv4 internet address) directed at server 1, how does the DA connection get to server 3 which has the DA role installed?
I could create another record on the server which also opens port 443 to server as well as for server 1, but then how would the router know which server to pass the DA connection to if the same port is open for two different servers?
Either way, this first issue is that the client doesn’t seem to have the ability to connect internally correctly yet, so maybe this connectivity service is a good place to start? My understanding is that the
networks icon in the system tray should show that there is a corporate connection, but it doesn’t. also, the client seems to have the NLS certificate in the computer certificate store, so the cert side of things is working and the GPO side is working.
Many thanks
Steve

ahh i see, so just to enlighten me even further...
If a company has two web servers that would mean they would need two different public facing IP addresses so they can route to each internal web server. If, like the big companies have, they
may have many web servers (possibly more than 100) I’m assuming that simply buying more public IP addresses would have a limit, especially since the IPv4 address space is pretty much exhausted. So is this where proxy systems come into play like ISA and Forefront,
is this what they do?
I assume if such a product was implemented you could go down to just one or two public IP addresses, point all traffic to the ISA server and that in turn would do all the routing of packets
to each server behind the NAT/router (probably based on some sort of domain name or sub domain namespace as it’s parameter for forwarding?)
Secondly, what I have done is installed windows server 2012 and used that as a direct access client (I read on another forum that the windows 8 RP doesn’t have the enterprise bits to make this
work). I have got much further with the 2012 server acting as a client (installed on laptop, installed desktop experience and wireless LAN),
but when I run the following command on my DA client I get the following status
Get-DAConnectionStatus
Status:
connectedlocally
Substatus:
none
This appears to work fine, when im connected to the local network. But then I disconnect and run the command again and I get the following:
Status:
Error
Substatus:
NameResolutionFailure
On my router what I did is temporarily disable port 443 going to my original server and instead opened it up pointing to my other server, so 443 traffic should be going to my DA server now, but I don’t understand why its giving the name resolution failure
status. I have a host A record called “da” with my domain hoster, and entered the full domain namespace in the DA wizard as da.mydomain.com (the Host A record has been up there for more than a week so it’s propagated through the net)
So, a bit further but stuck again.

Direct Access has no internet access

Hi all,
Hopefully some can help me with this issue that I have been struggling with for about a week now.
I'm new to Direct Access so please bear with me
I've setup a Server 2012 box and installed the Direct Access role. The server is behind en edge device with 1 NIC.
I've configured it and can connect up Windows 8.1 tablets successfully, both on the internal network and when connected externally.
The problem I have is with internet access when they are connected externally and I've tried with Force Tunneling enabled and disabled (ideally for security reasons I'd like it enabled).
We use a proxy server configured with a wpad file hosted on Server 2003. This is published via DNS.
Internet Explorer is configured to Auto Detect Internet Settings
I can connect to any of our internally hosted websites, and also strangely enough, our main publically accessible web site.
If I don't have Force Tunneling enabled then I get the following behavior
I can't use Internet Explorer to connect to any public websites though (google.com, yellowpages.com, etc).
I can connect to any website that has the same domain suffix as our domain
I can use Firefox and connect to external websites if I say 'Direct Connection to Internet' or 'Use System Settings'
If I use Force Tunneling then I get the following behavior:
The network connection says it is 'limited' and the Direct Access connection says it has 'No Internet Access'
I can't use Internet Explorer to connect to any public websites though (google.com, yellowpages.com, etc).
I can connect to any website that has the same domain suffix as our domain
I can't use Firefox and connect to external websites
Does anyone know why this would be the case?
Thanks

Thanks for the responses, I managed to get this working by unticking the 'Auto Detect Settings' and manually entering the proxy server and port under the 'Proxy Settings' option
It means that it doesn't read my wpad file but I can manage this way still through GP.
Another problem that I've just encountered for no reason that I can see is this.
I'm connected to my Domain, I pull the LAN cable and then it auto connects me to my wireless network. It used to auto connect me to my Direct Access server but it doesn't anymore, it just says connecting. If I reboot the tablet while on the wireless
LAN and then log on with my Domain Credentials it'll connect me through to the Direct Access server.
Why would it need a reboot? Why has it stopped connecting straight away after detecting I'm no longer on the domain?

Updated to firefox 4.0. since then my computer is very slow accessing the internet, websites and getting information from within a website.

Over a week ago I updated my computer to Firefox 4.0. Since then my computer is very slow accessing the internet, websites and getting information from within a website. Also, a tool bar has shown up for YAHOO which I did not request. The old detailed tool bar for Firefox has disappeared. All that now shows for Firefox is the area to enter website urls and an area to enter topic for a Google Search.
Many times I have to exit Firefox and re-enter it later to access the internet.
Please advice what I need to do to get back to the speed I had with the older version of Firefox.
Thank You,
Dennis

Over a week ago I updated my computer to Firefox 4.0. Since then my computer is very slow accessing the internet, websites and getting information from within a website. Also, a tool bar has shown up for YAHOO which I did not request. The old detailed tool bar for Firefox has disappeared. All that now shows for Firefox is the area to enter website urls and an area to enter topic for a Google Search.
Many times I have to exit Firefox and re-enter it later to access the internet.
Please advice what I need to do to get back to the speed I had with the older version of Firefox.
Thank You,
Dennis

Firefox will not access the internet. I have used Firefox for years and the past week I have not been able to get on the internet??? What is the problem. My interent works as I get email and can iuse Internet Explorer to access.

Firefox will not access the internet. I have used Firefox for years and the past week I have not been able to get on the internet??? What is the problem. My interent works as I get email and can iuse Internet Explorer to access

Which version of Firefox are you using?
See
* https://support.mozilla.com/en-US/kb/Firefox%20cannot%20load%20websites%20but%20other%20programs%20can

WRE54G is already connected to WRT160N Router, but can not get access to internet?

Hello,,,
I have seven of rung expanders WRE54G and all settings i set as this link
http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=4104&p_created=11611...
* same wireless SSID name
* same Channle ( What is the difference between the channel number 6 & number 11 for example?)
* security ( i used WPA2 mixed, that is not in WRE54G, so what i should use)
* Each Expander has own IP address as 192.168.1.2 up to 192.168.1.8
Is the gateway mean the main IP of router 192.168.1.1 ?
all those expanders connected with WRT160N ( the Link gets Blue light)
but my laptop can not get the IP address near of any of those expanders, to get the access to the internet!!!!
What is the reason please?
Message Edited by Almowdmer on 11-10-2008 12:42 AM

I am very happy to communicate with you ( I sure i can learn some thing from you my brother )
Your words are true seven the number of expanders is not easy option
or the cause of the success of the wireless network coverage May succeed strengthened,
with one or two, but more than that needs to be a better distributor.
I think I will use RangePlus WRT110 as repeater in some floor where the wireless signal
is not can work, after connecting through the wire with the main router,
and then I can get half the reference from the repeater when i useing the WRE54G expander
What do you think?!!
I put on my experience on this link
http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&thread.id=115808
Message Edited by Almowdmer on 11-16-2008 10:21 PM

After a router reset, can't get second PC to access the internet

I had my wireless router (WRT54G) and printserver working fine and then a problem with my DSL had me resetting both boxes (yeah I should have know better). I've fought back and have everthing working for one PC that has an internal wireless but my other PC has a WPC54G wireless card and I can't get it to work. Both PCs are XP, SP2. The Linksys appl says that it contacted the access point but can't access the internet. It has always been flaky about this but usually gets to the internet. It does have a good IP address, the WEP key and channel are right but 'no joy'. I can ping the router and the printserver but I can't bring up the router's home page but I can print to the printserv. I did not change the modem to 'bridge' yet.
TIA....jack

What is the IP Address you are getting on the computer...?It should be in the range of your router.IP Address should be 192.168.1.x, Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1 (assuming your router is 192.168.1.1)...
If you get the above mentioned IP Address, Subnet and Gateway Address then you should ping the Gateway, type ping 192.168.1.1 and press Enter...If it gives you request timed out then disable any firewalls, security software on the computer...
If you get 4 replies then type ping 4.2.2.2 and press Enter, if you get request timed out, then you need to upgrade your router's firmware...If you get 4 replies then type ping yahoo.com and press Enter...If you get replies for Yahoo then you should get the Internet after adjusting the browser settings...
Adjusting Browser Settings : Open an IE, click Tools >> Internet Options, then delete all files, cookies, history, forms...Goto "Connections", make sure Never Dial a Connection is checked, click on LAN Settings and make sure all the options are unchecked...Once you are done click on O.k...Close the IE and re-open it...
If yahoo times out then provide static DNS on your WAN Connection...
Click on the Start button >>> Settings >>> Control Panel >>>Network Connections- Right click on the icon for Wireless Network Connection and go to properties- On the 'General' tab select 'Internet Protocol TCP/IP' and click on the Properties button- Select 'Use the Following DNS Settings' Preferred DNS 4.2.2.2 Alternate DNS - 4.2.2.3>>Click on Ok button to Save and Click on "Close" on main Properties window...You should be able to go online...

After login but before I can access the internet I get a request for my login password so that - aosnotifyd - can access my login key chain. How can I get it to remember my password?

After login but before I can access the internet I get a request for my login password so that - aosnotifyd - can access my login key chain. How can I get it to remember my password?

Rephrase your question. Do you mean you keep getting login key chain errors?

Getting direct access to Internet is sporadic.

Similar Messages

Maybe you are looking for