Getting error messages upon startup after installing Lab View 5.1.1.

I have recently purchased a DAQ system along with a computer, which uses a readout program written in Lab View. however, after installing Lab View 5.1.1 on this same system, I started getting some error messages and the readout program no longer works. Here are the error messages:
"The \SystemRoot\system32\drivers\nidmmk.dll device driver could not locate the entry point ?single PointWrite@mdsSimpleDIGPortPrimitive@@UAEXKKKAAJ@Z in driver Nidaq32K.sys"
as well as
"The ordinal 2011 could not be located in the dynamic link library nidaq32.dll. An error occurred while loading VT Digital buffer write.vi"
I would greatly appreciate any help I can get.

Hello,
Installing LabVIEW should not effect an installation of NI-DAQ. However, it seems to me that we may have installed a different version of NI-DAQ on top of the current version. This is very possible because the old LabVIEW CD�s contain NI-DAQ on them.
In this case, there is not an easy solution, we could try uninstalling and reinstalling combinations, but it will probably save the most time and effort to uninstall all National Instruments products and reinstall them. The best way to do so is from the ADD or REMOVE Programs utility from the Control Panel. Then we want to remove the following registry keys (BE SURE TO BACKUP YOUR REGISTRY!!)
HKEY_CURRENT_USER\Software\National Instruments <-- Delete the entire tree!
HKEY_LOCAL_MACHINE\Software\National Instruments <-- Delete the entire tree!
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Enum\PCI\ or \ISA and delete registry entries containing any keys with 1093 in them.
Do not worry if any of these trees are not listed. If you have Administrative rights, and you still cannot delete these keys, that is also OK. Continue with the remainder of the process.
Make sure that you do not have any of your own VIs or other files saved in the "C:\VXIpnp", "C:\Program Files\National Instruments", or "C:\WINDOWS\nidaq" folders. If you do, copy them to a different location. If you are concerned about keeping old virtual channels and your SCXI setup intact, then backup the "C:\WINDOWS\niconfig.daq" file, too. Delete all folders and files mentioned above.
Note: If you have Windows NT/2000, replace "C:\Windows" with "C:\WINNT" in the paths listed above.
Once these steps are taken care of, we should have clean system. You probably want to reboot and then reinstall the software. You should install development environments first, and then install drivers.
Just let us know if this does not take care of the problem, or if you have any questions on how to complete a step of the process.
Best regards,
Justin T.
National Instruments
NOTE: Turning off virus scan programs greatly increases the speed of uninstalling and reinstalling.

Similar Messages

HT5634 27 in late 2009 iMac and using bootcamp 4 and windows 8 64 bit I am getting a error message upon startup

I have a 27 in late 2009 iMac and using bootcamp 4 and windows 8 64 bit I am getting a error message upon startup. Any way to fix it?

Windows 8 is not supported on your computer.
http://support.apple.com/kb/HT5634

I get an error message upon startup: "TypeError: Components.classes[cid] is undefined." Help!

In addition to the error message upon startup, the Enter key does nothing when I type a URL in the search bar; I have to click on the green arrow everytime to navigate to new pages. My about.home page is also empty when the program starts except a blank search bar in the center with no text anywhere around it. I installed 4.0 twice to see if that would fix the problems, but it didn't.

Usually caused by an incompatible extension.
http://support.mozilla.com/en-US/kb/troubleshooting+extensions+and+themes

Trying to install final cut express keep getting error message "FCE" can't install on this disk. A newer version of this software already exists on this disk. Have remove all FCE elements with no success.

Keep getting error message "FCE" can't install on this disk. A newer version of this software already exists on this disk. Have remove all FCE elements with no success.

http://www.digitalrebellion.com/fcsremover/

HT201444 Getting error message 4005 so re-installed latest version of itunes, restarted computer, everythingis up to date. Still getting erro 4005. This happened when I went to update software. Face of ipad showing a cable not connecting to itunes

How can i restore my ipad to factory settings?
Getting error message 4005 so re-installed latest version of itunes, restarted computer, everythingis up to date. Still getting error 4005. This happened when I went to update software. Face of ipad showing a cable not connecting to itunes

Usually a USB error. Read here:
http://support.apple.com/kb/ts3694#4016
To restore ipad: Settings > General >(Scroll down) >Reset > Erase All Content & Settings
Cheers,
Alec

Trying to install windows 7 and getting error message windows must be installed to a partition formatted as NTFS

Trying to install windows 7 and getting error message Windows must be installed to a partition formatted as NTFS

Welcome to Apple Support Communities
Boot Camp Assistant creates a Windows partition in FAT32 to make the Windows XP installation easier.
The problem is that Windows Vista, 7 and 8 require a NTFS partition, so the Windows installer gives this error. The only thing you have to do is to choose the BOOTCAMP partition in the installer and go to “Drive options (advanced)” > Format. Finally, install it

I had an Iphone 4 and now i have an iphone 4s. I had itunes on the same compute as before and now when i try to download it i get error message. "didn't install correctly".

I had iphone 4 and now i have an iphone 4s. I had itunes on this pc and it worked fine with the 4. Now i keep getting error message 7 that it didn't install correctly. Help!!!!
I need my itunes now.

Hello labnutt,
After reviewing your post, I have located an article that can help with errors in iTunes for Windows. It contains a number of troubleshooting steps and helpful advice for the issue you are experiencing:
iTunes for Windows: "Error 7" message when opening iTunes - Apple Support
Thank you for contributing to Apple Support Communities.
Cheers,
BobbyD

Get error message when trying to install windows. need to remort hd. how to

tried to install xp with bootcamp. get error message when trying to partion the disk:"the disk can not be partioned because some files cannot be moved.
back up the disk and use Disk Utility to format it as a single Mac OS Extended
(Journaled) volume. Restore your information to the disk and try using Boot Camp
Assistant again."
bought an external hd and used time machine to back up everything. do not understand how to reformat the hd with disk utilities. any help is appreciated

Hi and welcome to Discussions,
have a look at the answers in this thread http://discussions.apple.com/thread.jspa?threadID=1972468&start=0&tstart=0 for an easier way to do this.
Regards
Stefan
Message was edited by: Fortuny

QUESTION ABOUT AN ERROR MESSAGE UPON STARTUP OF COMPUTER

I receive an error message at startup that says:
"an unexpected error occured while trying to load the microsolf framework library"
Is this causing damage to my computer? If so, what should I do?
I had my old info from my previous mac transfered to this new one.

Any help looking through these?
http://discussions.apple.com/search.jspa?objID=f808&search=Go&q=error+48

I keep getting a "Flash blocker browser settings or extension" error message in Soundcloud after installing fire fox. I have tried flash 11 & 10.3

I keep getting an error message saying "It looks like you have a flash blocker browser settings or extension. Please enable flash to hear sound" error message come up when I try to play music in Soundcloud. I have just installed Firefox on my laptop and upgraded to the latest Flash player. I then tried down grading to Flash 10.3 but this didn't help. I have been watching programs in iplayer and had no problems there. Please help!

I have been through this process several times. It sometimes works and sometimes it doesn't. Running in safe mode proves nothing.
Youtube videos work fine. So flash is working. Hosts file is the default one so nothing blocked). No sit blockers etc. all disabled in add-on manager.
Old Soundcloud works fine. Sometimes the new one does. Most of the time it does not.
Switch to IE8 (yuch) and this gets even worse. Old SC works but new one says I need an update and provides a link. I click the link and MS site says I am a;ready running the most up to date browser.
Bottom line...
1) if you use IE, better go to Windows 7 or 8. Otherwise Soundcloud should be avoided. Sure, the old SC still works ... for now.
2) if you use Firefox, roll dem bones and see what ya get. Maybe it will work. Maybe it won't. But it's a pain to have to keep clearing the cache and cookies to fix the one and only site that has this issue with Firefox 18.
3) go to Chrome if you love google. It seems to be OK.
4) ignore soundcloud all together. It's not going to survive long in this mode.

Installed Firefox 4 on my Mac; getting error messages upon start up and when opening photos (i.e. ebay)

I updated to Firefox 4 and now continuously receive error messages. One example is when I'm in Ebay and click on a photo to enlarge I get the following error message.
(JavaScript Application)
can't create mcafee plug-in object: TypeError:
Components.classes(cid) is undefined
Another example is upon start up of Firefox I receive an error message but I can't make it out since its half hidden on my desktop but I have to click "ok" in order to open up Firefox.
I'm barely learning how to use this Mac (a task in its self), but now I have these error messages? Can I just go back to my older version of Firefox to make these error messages go away?
Thanks, JR.

Thank you very, very much. This was my very first time trying to solve a technical issue on my Mac... your advice worked great. I disabled all the add-on apps and it solved my issue. Don't know if I should have disabled all but it seemed to work... Thanks again for the advice.

Since updating to 10.4 getting error message on startup 'AppleSyncNotifier.exe – Entry Point Not Found, The procedure entry point xmlTextReaderConstName could not be located in the dynamic link library libxml2.dll.'. How do I fix this annoying problem?

Since updating to 10.4 I've been getting this error message on computer startup
'AppleSyncNotifier.exe – Entry Point Not Found
The procedure entry point xmlTextReaderConstName could not be located in the dynamic link library libxml2.dll.'.
Please help me fix this annoying problem?
belle

This is the fix I got from discussions and it worked for me. It is copied below. I just did the manual fix which I have underlined. Good luck! Regards, Belle.
This can occur because libmxl2.dll is not in your C:\Program Files\Common Files\Apple\Mobile Device Support folder.
There have been some issues with this and other dlls not being in the right place (or not being everywhere they should be) since the 10.3.1.55 iTunes update.
However, I note that the 10.4 iTunes update is now out - surprisingly quickly - so try installing that, rebooting, and see if your issue is solved.
If it isn't, though, here's the manual fix:-
With Windows Explorer, navigate to your C:\Program Files\Common Files\Apple\Apple Application Support folder.
Copy the libmxl2.dll that you should find there, navigate to the nearby Mobile Device Support folder, and Paste it in there also.
Reboot and see if all is well.
I actually had the issue with SQLite3.dll, and the above fix worked for me (I found it in an April 2010 posting!).
I passed on the fix as above for the similar issue with libmxl2.dll to someone who had exactly your problem, and he reported that it fixed it for him.

Why am i getting error message when trying to install iOS 7.0.3 to iPhone 5? It just won't download.

Why am i getting an error message when trying to download and install iOS 7.0,3 to iPhone 5?

Sharonc21 wrote:
If one is downloading directly to the iPhone via WiFi, it doesn't matter what version of iTunes is on the computer.
I decided to sync my phone to Outlook via iTunes. First thing, iTunes discovered that 7.0.3 was not on my phone. It asked if i wanted to install it. I said, "yes", and VOILA!! 7.0.3 is now installed on my iPhone.
So therein is the answer. Have no idea what bug is in there to keep it from loading to some phones directly via WiFi, but obviously, it is something!!
There is no bug. While you can update your iOS via wi-fi, it's recommended to do so via USB & iTunes. Depending on your wi-fi connection & singal strength, you can get errors. That's not a function specifically of the device.

How do you clear Error Message 3100? After installing the New inks, On NEW 'Canon MX432' Printer

Have NEW ‘Canon MX432’, (1)-followed the instructions to set language without problem, next step, checked for the Set ink cartridge Message, (2)-and then opened the Paper Output Tray and the Paper Output Cover.
On the second try; (3)-the Head Cover opened automatically, (4)-then lowered the Color Ink Cartridge Lever, (5)-Unpacked the FINE Cartridge and remove the protective tape, (6)-then Inserted the FINE Cartridge straight in until it stopped, (7)-and lifted the Color Ink Cartridge Lever.
Next did the same steps (8) - (9) - (10)- (11)-to the Black Cartridge, next (12)-Closed the Paper Output Cover.
*** Should I have waited and lifted both Levers at the same time? ***
(13)-Waited for printer, (14)-got error Message; ”Printer Error occurred”, then the numbers; “5100”.
Have tried unplugging the printer a few minutes and repeating the steps from the start to no avail.
Next will go buy new Ink and try again or return this Canon MX432 Printer, for a different Model.
Do not want to install new Ink Color and Black Cartridges until I understand the problem solution.
Have used Canon products for over 30 years never had this problem or any problems with their products which could not be resolved by me.
Steps Followed:
*** Do you see a problem with these steps taken? ***
(1)- Set language
Waited for the “Set ink cartridge” Message
(2)- Opened the Paper Output Tray and the Paper Output Cover
(3)-The Head Cover opened automatically
(4)-Lowered the Color Ink Cartridge Lever
(5)-Unpacked the Color FINE Cartridge and remove the protective tape
(6)-Inserted the FINE Cartridge straight in until it stopped
(7)-Lifted the Color Ink Cartridge Lever
(8)-Lowered the Black Ink Cartridge Lever on the left
(9)-Unpacked the Black FINE Cartridge and remove the protective tape
(10)-Inserted the Black FINE Cartridge straight in until it stopped
(11)-Lifted the Color Ink Cartridge Lever
(13)-Closed the Paper Output Cover
*** Should I have waited and lifted both Levers at the same time? ***
(13)-Waited for printer
(14)-Got error Message: ”Printer Error occurred”, then the numbers; “5100”

Hi Anselmo_MSW!
It looks as though you have followed the correct steps and no, you do not need to lift up both levers at the same time.
The error code 5100 indicates that an internal error has occurred which may be resolved by resetting the printer. Please follow these steps for isolating and resetting the printer:
1. Open the printer's front cover, and then open and close the print head lock lever (do not remove the print head).
2. Make sure all ink tanks are seated properly.
3. Make sure all packing materials have been removed.
4. Make sure no paper is jammed in the printer.
5. Disconnect the printer cable from the printer.
6. Close the front cover and turn the printer off.
7. Unplug the printer from the power source, and then plug it back in after five minutes.
8. Power on the printer.
If the error returns, the printer will require service options. I realize you have just purchased this and wanted to let you know that this is not the normal operation of our printers. What I would recommend is contacting a Canon Representative using the following link to learn of your service options. Contact Us.

Error Message Upon Startup

Hello All,
I'm having this very annoying problem with iTunes 7.6. When I try to start the application, I get the standard Windows error message: "iTunes has encountered a problem and needs to close." Here is the only info I have on it, from the error report:
AppName: itunes.exe AppVer: 7.6.2.9 ModName: unknown
ModVer: 0.0.0.0 Offset: 000c0189
I've tried uninstalling and reinstalling, I've tried the Repair function on the installer, I've tried using a different installer download, and nothing is working.
It is worth pointing out to you tech-savvy people that when I first encountered I had an iTunes problem was when I tried to open it (it must've been 2 months since I'd last tried it on this computer, I don't recall any problems beforehand), it said I needed to update QuickTime. I did, and then this. Now neither iTunes nor QuickTime works. The same thing happens with QuickTime.
HELP!!!!!
Thanks!
Cheers,
Cameron

The QuickTime problem will be causing the iTunes problem. (iTunes needs a properly functioning QuickTime in order to work correctly.)
So let's try swapping out your existing QuickTime.
Head into your Add/Remove programs. uninstall QuickTime.
Next, we’ll manually remove any leftover program files and folders.
1. On the Start menu, click My Computer (or double-click My Computer on the Desktop).
2. In My Computer, open Local Disk.
3. Open Program Files.
4. Right-click on the QuickTime folder and click Delete from the shortcut menu.
5. Navigate to C:\Windows\system32\.
6. Remove the files QuickTime.qts and QuicktimeVR.qtx. (If “Hide filename extensions for known file types” is enabled on the PC, then those two files will appear as “QuickTime” and QuickTimeVR”.)
7. Restart your computer.
Next, we'll get a fresh copy of QuickTime into your PC by doing a repair install of itunes.
Switch off antivirus and antispyware applications prior to the repair install.
Go into Add/Remove and select itunes. Click "Change" and then click "Repair".
If the repair install goes through okay, restart the PC and try launching itunes again. Does it launch properly now?

Getting error messages upon startup after installing Lab View 5.1.1.

Similar Messages

Maybe you are looking for