Getting NVIDIA RIVA TNT2 to work?

Hi,
i'm trying to get my video card to work correctly. It seems to be:
NVIDIA RIVA TNT2 Model 64/Model 64 Pro GPU
I checked in Xorg's logs and it seems it wants a driver called nvidia-71xx. I checked in the repositories and it doesn't seem to be there. I found a package on the Nvidia site but it asks me to compile a custom kernel or something like that. Anybody knows what's the proper way to make this card works? The Nvidia packages on the site didn't seem to work on it, they are all too new, even the old one.
EDIT: Saw the post about the new package and installed it. I now get a bunch of lines on screen but no image.
Last edited by Greenstuff (2009-07-14 22:48:22)

As far as I know you would need the 71.XXX series of the driver. Unfortunately nvidia did not update it for use with xorg >1.5.
Check out this thread:
http://www.nvnews.net/vbulletin/showthread.php?t=122436
There is a small chance that we may add support in the future, but there currently are no plans to do so, as Aaron said.
What do you mean with "and no new 'nv' driver's added"? What das X -configure say which drivers are available?

Similar Messages

NVIDIA RIVA TNT2 MODEL 64 Pro

Hello my friends, I am beginner in the big world of Solaris, I am using the
version 8.1 for Intel X86 . The question is I have a video card NVIDIA RIVA
TNT2 on Dell Optiplex GX200 system Does anybody know where I can get this
driver or some similar one to use in Solaris?
Thank you very much
Daniel Susca

Hello,
i used for my gerforce2 64MB the driver from xfree Driver Porting kit.
"http://soldc.sun.com/developer/support/driver/tools/video/video-index.html
have fun.
svelele

Getting nVidia 71xx driver to work.

I spent much of last night installing and setting up Arch Linux. During the installation, I attempted to install the "nvidia-71xx" driver so I could make use of my Riva TNT2 card. However, I met with a problem during the configuration: nvidia-xconfig was not present. So, how do I go about installing and configuring nvidia-71xx now?

I managed to get nvidia-71xx installed, and I manually configured xorg.conf. But now, ksplash is crashing whenever I log in. Running "glxinfo" in the command line reveals this:
name of display: :0.0
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
Error: couldn't find RGB GLX visual
visual x bf lv rg d st colorbuffer ax dp st accumbuffer ms cav
id dep cl sp sz l ci b ro r g b a bf th cl r g b a ns b eat
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x21 24 tc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x22 24 dc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x23 24 tc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x24 24 tc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x25 24 tc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x26 24 tc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x27 24 tc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x28 24 tc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x29 24 tc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x2a 24 dc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x2b 24 dc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x2c 24 dc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x2d 24 dc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x2e 24 dc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x2f 24 dc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x30 24 dc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Xlib: extension "GLX" missing on display ":0.0".
Xlib: extension "GLX" missing on display ":0.0".
0x61 32 tc 1 0 0 c . . 0 0 0 0 0 0 0 0 0 0 0 0 0 None
Segmentation fault
I recall having a similar problem on Fedora. It had something to do with compositing, I think. Here's the contents of my /etc/X11/xorg.conf file:
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
InputDevice "Mouse0" "CorePointer"
InputDevice "Keyboard0" "CoreKeyboard"
EndSection
Section "Files"
RgbPath "/usr/share/X11/rgb"
ModulePath "/usr/lib/xorg/modules"
FontPath "/usr/share/fonts/misc"
FontPath "/usr/share/fonts/100dpi:unscaled"
FontPath "/usr/share/fonts/75dpi:unscaled"
FontPath "/usr/share/fonts/TTF"
FontPath "/usr/share/fonts/Type1"
EndSection
Section "Module"
Load "glx"
# Load "GLcore"
Load "record"
Load "xtrap"
# Load "dri"
Load "dbe"
Load "ddc"
Load "extmod"
Load "freetype"
EndSection
Section "InputDevice"
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "InputDevice"
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/input/mice"
Option "ZAxisMapping" "4 5 6 7"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "DELL"
ModelName "DELL P780"
HorizSync 30.0 - 85.0
VertRefresh 48.0 - 120.0
DisplaySize 370 270
EndSection
Section "Device"
### Available Driver options are:-
### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
### [arg]: arg optional
#Option "SWcursor" # [<bool>]
#Option "HWcursor" # [<bool>]
#Option "NoAccel" # [<bool>]
#Option "ShadowFB" # [<bool>]
#Option "UseFBDev" # [<bool>]
#Option "Rotate" # [<str>]
#Option "VideoKey" # <i>
#Option "FlatPanel" # [<bool>]
#Option "FPDither" # [<bool>]
#Option "CrtcNumber" # <i>
#Option "FPScale" # [<bool>]
#Option "FPTweak" # <i>
#Option "DualHead" # [<bool>]
Identifier "Card0"
Driver "nvidia"
VendorName "nVidia Corporation"
BoardName "NV4 [RIVA TNT]"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Card0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 1
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 4
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 8
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 15
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 16
EndSubSection
SubSection "Display"
Viewport 0 0
Depth 24
Modes "1280x1024" "1152x864" "1024x768" "800x600"
"640x480"
EndSubSection
EndSection

Installing Solaris 8 with a NVIDIA RIVA TNT MODEL 64 video board

I'm trying to find out if anybody knows of any compatible drivers for the NVIDIA RIVA TNT MODEL 64 video board for Solaris 8.
I can install Solaris using 640 x 480 with 16 colours, and that works without any problem, but the installation does not seem to have any compatible drivers.
I've tried contacting NVIDIA but have not received any reply.
Any help would be greatly appreciated.

Hi Mark,
It appears as if this particular chipset is supported as suggested
in the Hardware Compatibility List.
The -- in the bus field indicates that this chipset is used on different video devices whether they be motherboard integrated
video cards or dedictaed video cards. (Check the notes at the top
of the video display adapter listings).
The note also explains that there is no guarantee that the same
chipset will work with all video devices; only a selceted number
of devices with this chipset have been tested.
I just located a report where this particular chipset caused exactly the same problem. The TNT2 was integrated into a Microstar 694D motherboard. A full investigation was not carried out as the customer in this case closed the call having used a different card.
As far as I know, the NVIDIA RIVA TNT2 chipset has successfully been
tested on the Diamond Viper V770 and Creative Labs 3D Blaster RIVA TNT2.
Upon bootup what is the BIOS level of the card as reported? Another
engineer has managed to test a card with TNT2 BIOS 2.05.04, 32MB.
I think that webstart problems were avoided by installing directly from the SOftware CD's 1of 2 and 2 of 2 in non graphics mode (opting not to specify video at the kdmconfig screens)
Regards
Derek SUN-DTS

Solaris 8 with Aopen nVIDA Riva TNT2 AGP problem

Is there any solution so that solaris 8 (intel) recognize the Aopen nVida Riva TNT2 AGP 32M card, Thanks

Maybe <a
href="http://sunsolve.sun.com/pub-cgi/retrieve.pl?patchid=109401&collection=fpatches">
patch 109401-03</a> helps?
<pre>
Patch-ID# 109401-03
Keywords: X11 Server video configuration ati matrox nvidia
Synopsis: X11 6.4.1_x86: Updated Intel X Server video support (S8).
Date: Dec/07/2000
...4331923 "kdmconfig -d" does not save the keyboard information
(from 109401-02)
4282716 ATI RAGE 128: Add new video support
4359858 NVIDIA TNT2 M64: add video support
4360725 VIDIA TNT2: mouse pointer visible when screen blanked
4360743 NVIDIA TNT2: some vga text mode apps leaves boarder in dtterm
4361998 ATI RAGE 128: 32MB cards don't work in low-res modes
4361061 ATI RAGE XL: device not recognized by kdmconfig in new Compaq
system
</pre>

NVidia SDI doesn't work

Upgrades 1 and 2 are very disappointing. My system has NVidia SDI and BMD Extreme 3D both installed. After upgrades NVidia SDI doesn't work and the BMD doesn't do 3D.
Again, is there any real testing done before a release or is it just left to the paying customers to find the bugs. Frankly I need to get work done.

This is the most recent info I've found on using the SDI outs ... and yes, I do hope this works easy, more obvious, and more reliable for people with the next release. They have acknowledged here that this is not always functioning properly for all setups and all external "tools" at this time. Which is about as much as they could do really.
Advanced dual-monitor setup
The advanced dual monitor setup uses nVidia Quadro SDI technology to allow for real-time 10- and 12-bit output over Single Link or Dual Link SDI. The nVidia Quadro SDI setup requires a 64-bit Windows 7 system.
Connect the DVI or DisplayPort output to the display you want to use for the SpeedGrade workspace.
Use either a Single Link or Dual Link SDI output from the NVIDIA SDI card to connect with external waveform and other monitoring devices, and your reference monitor or projector.
In SpeedGrade, select Settings > Display.
In the SDI Output section, change signal and format settings according to your desired output format settings.
Select the Enable option.
FAQ: How many outputs on the nVidia GPU can be used in parallel?
Only two outputs at a time can be used in parallel. The SDI card is routed through the Quadro GPU and thus takes one DVI or DP output. The other output can be used for the workspace display. The additional DisplayPort is not active in parallel.
Tip: Combining local footage display with a projection setup
To give the operator an accurate local display in parallel to another display or projection system, a signal split on the SDI output is recommended. This is the recommended way to monitor a signal through external waveform and vectorscope devices.
Using multiple monitors also requires an understanding of the odd way SpeedGrade "references" multiple monitors in the setup section. So you have to figure out how to set those numbers for the second display AND the above info on SDI to get it to work. Note, basically they suggest running two monitors and if you need more ... run a splitter on one channel outside the computer. So say your external scopes and broadcast monitor would run off one output from the computer, connected to some external box.
As for the two monitor setup, SpeedGrade assumes 1920x1080 monitors ... and that the interface shall be on the Primary monitor as determined by the computer system. So when setting the numbers in the dual monitor setup, you use "Top" to tell Sg the * relative * position of the top left pixel of the second monitor to the primary monitor. The " 1 " pixel is the primary monitor's upper-left pixel, all else is computed from that point, going to the right and down. In my case, my monitors are stacked, primary on the bottom, program monitor on top. So I set the "top" number to -1080 so Sg "knows" the top left pixel of my second screen is 1080 pixels "earlier" (negative) than the primary top left pixel.
As the two monitors are relatively in line vertically, the "left" number is " 0 ". And as the second monitor is 1920x1080 I put those numbers in the height/width area. SpeedGrade ... normally ... understands the basic pixel dimensions of the primary monitor, but you have to tell it the size of the secondary one. If your secondary is say 3,840 × 2,160, you'd put that in the width/height, and compute (depending on where your top-left secondary pixel is from top-left primary pixel) the figures above. Trip up on any of the above, you get ... bizarity. Truely.
Neil

Nvidia driver won't work

I can't seem to get my graphics card to work. It is a GeForce 5500 and is supposed to work with the regular nvidia driver. I have also tried using the nvidia-96xx driver with the same results. I am using the VESA driver right now
this is the error that i get:
could not open '/lib/modules/2.6.24-ARCH/kernel/drivers/video/nvidia.ko
No such file or directory
NVIDIA: faled to load the NVIDIA kernel module
Screen(s) found, but none have a usable configuration
It was working a few days ago until an -Syu when the kernel was upgraded. I messed with it for quite some time and decided to just reinstall arch and start fresh (I had been meaning to for a while anyway) but the problem persists on the new install too.
I don't know what to do, any ideas?
thanks

Have you had a look in '/lib/modules/2.6.24-ARCH/kernel/drivers/video/' to see if the driver is actually there ?
The thing I would do in this case ( and I'm a notorious ass**** ! ) is logout, do a Console login, as root run
'xorgconfig', re-install the Nvidia driver (It'll bitch about it already being installed, just go ahead...) then reboot.
WARNING: if you run 'xorgconfig' it'll require your monitors horizontal and vertical scanning frequencies. If you don't know them you may be able to Google for them.
After any kernel upgrade / downgrade the Nvidia driver will require re-installation.
Hope this helps...
Deej

Nvidia GeForce GT430 not working in OSX

Is there any way to get a Nvidia GeForce GT 430 working in OSX on a Mac Pro?

Is there any way to get a Nvidia GeForce GT 430 working in OSX on a Mac Pro?

I have a macbook pro version 10.7.5 and my mailbox will not open at all and comes up with a quit message even though it is not open. how can i get into my account. it works on my iPhone an i have internet and all other functions working on my computer

I have a macbook pro version 10.7.5 and my mailbox will not open at all and comes up with a quit message even though it is not open. how can i get into my account. it works on my iPhone and i have internet and all other functions working on my computer

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Step 1
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Enter the name of the crashed application or process in the Filter text field. Select the messages from the time of the last crash, if any. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Anonymize before posting.
Step 2
In the Console window, look under User Diagnostic Reports (not "Diagnostic and Usage Messages") for crash reports related to the crashed process. The report name starts with the name of the process, and ends with ".crash". Select the most recent report and post the entire contents—the text, not a screenshot. I know the report is long. Please post all of it anyway.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
Please don’t post other kinds of diagnostic report—they're very long and rarely helpful.

I was editing photos and it was getting stuck or frozen and working really slow, so I attempting to close aperture and reopen it but it won't quit aperture and now it won't open up to my photos either. Any ideas?

I was editing photos and it was getting stuck or frozen and working very slowly. I attempted to restart the computer but it would not allow me to quit aperture. Now aperture appears in my toolbar but will not open up so I can work on any photos. Any ideas?

Did you try opening from the Applications folder?
Depending on how far that gets you, I would also take a look at the Troubleshooting Basics.

Cannot get the Mobile Template to work in SharePoint Foundation 2013

Hello all,
I am trying to get the Mobile View to work in SharePoint Foundation 2013. When I access the site on any phone it gives me the following error:
"Cannot complete this action. Please try again."
The URL it forwards me to is "http://<sitecollectionurl>/_layouts/15/mobile/mblwpa.aspx?Url=%2Fdefault%2Easpx
So it seems to me like it's working, but there's something wrong with the template. The template has definitely never been modified.
Can anyone help?
Thanks,
Vinny
Vinny

So I've got some more info for this issue. We are seeing:
Control template "Mobile_STS_HomePage_Redirect" does not exist.
Control template "Mobile_1_HomePage_Redirect" does not exist.
Does anyone know how to enable these? I tried by name, but it doesn't find them. This is the error I get:
PS C:\> Add-SPSiteSubscriptionFeaturePackMember <FeaturePackGUID> -FeatureDefinition Mobile_STS_HomePage_Redirect
Add-SPSiteSubscriptionFeaturePackMember : Cannot find a Feature object with Path or Id: Mobile_STS_HomePage_Redirect in scope Local farm.
At line:1 char:1
+ Add-SPSiteSubscriptionFeaturePackMember <FeaturePackGUID> -Fe ...
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : InvalidData: (Microsoft.Share...aturePackMember:SPCmdletAddSite...aturePackMember) [Add-SPSiteSubscriptionFe
aturePackMember], SPCmdletPipeBindException
+ FullyQualifiedErrorId : Microsoft.SharePoint.PowerShell.SPCmdletAddSiteSubscriptionFeaturePackMember
Vinny

How to get all kind of GP work items for all users

Dear all:
   Basing GP implementation,we can only get the single user's work item. Is that possible to get all of the users' work items,and can filter the work item via time field?
thanks a lot.

ISearchResult result=UMFactory.getUserFactory().getUniqueIDs();
               IUser iuser;
               while(result.hasNext())
                    iuser=UMFactory.getUserFactory().getUser(result.next().toString());
The above code retrives all the users from the UME
IGPUserContext context = GPContextFactory.getContextManager().createUserContext(iuser);
IGPWorkItem[] workitems = GPProcessFactory.getRuntimeManager().getWorkItems(GPWorkItemStatus.getTypeForCode("1"), context);
You will get the WorkListItems in the workitems array. The type for code which is 1 currently, must be changed according to the requirement. It is different for Completed, Inprogress Tasks, etc.
Hope this will help you!

I am trying to use an education program that needs Java applets to install and use and it will not use Safari. When I download IE from the web it will not install. How can I get a browser that will work on my MacAir for travel use of this program?

I am trying to use and education program that needs Java applets and it will not run on Safari. IE will not install from the web. How do I get a browser that will work to install so I can use this program when I travel.

Try using FireFox. IE will only run on a Mac if you run Windows on the Mac.
Windows on Intel Macs
There are presently several alternatives for running Windows on Intel Macs.
Install the Apple Boot Camp software. Purchase Windows 7 or Windows 8. Follow instructions in the Boot Camp documentation on installation of Boot Camp, creating Driver CD, and installing Windows. Boot Camp enables you to boot the computer into OS X or Windows.
Parallels Desktop for Mac and Windows XP, Vista Business, Vista Ultimate, or Windows 7. Parallels is software virtualization that enables running Windows concurrently with OS X.
VM Fusion and Windows XP, Vista Business, Vista Ultimate, or Windows 7. VM Fusion is software virtualization that enables running Windows concurrently with OS X.
CrossOver which enables running many Windows applications without having to install Windows. The Windows applications can run concurrently with OS X.
VirtualBox is a new Open Source freeware virtual machine such as VM Fusion and Parallels that was developed by Solaris. It is not as fully developed for the Mac as Parallels and VM Fusion.
Note that Parallels and VM Fusion can also run other operating systems such as Linux, Unix, OS/2, Solaris, etc. There are performance differences between dual-boot systems and virtualization. The latter tend to be a little slower (not much) and do not provide the video performance of the dual-boot system. See MacTech.com's Virtualization Benchmarking for comparisons of Boot Camp, Parallels, and VM Fusion. A more recent comparison of Parallels, VM Fusion, and Virtual Box is found at Virtualization Benchmarks- Parallels 10 vs. Fusion 7 vs. VirtualBox. Boot Camp is only available with Leopard and later. Except for Crossover and a couple of similar alternatives like DarWine you must have a valid installer disc for Windows.
You must also have an internal optical drive for installing Windows. Windows cannot be installed from an external optical drive.

How do I get my iTunes store to work? I have updated my iTunes to the latest version but every time I go to open it, it is just a blank white screen. No writing or anything. Help!?

How do I get my iTunes store to work? I have updated my iTunes to the latest version but every time I go to open it, it is just a blank white screen. No writing or anything. Help!?

Oh, and it is on a macbook pro

I can't get my itunes store to work, it keeps giving the error (-1202)

Hello,
I'm really frustrated as I cannot get my itunes store to work, I've had problems with it for a while now and only just manged to get past one error, (error -9808), only to now get the error -1202. I'm running the most up to date version of itunes as I have just downloaded it, (I know it worked as I can now see the cloud feature on the menu), but no images appear on any of the interfaces; only small blue boxes with question marks in them. Plus all the text appears in a plain font that I know is not how it should appear. My own music collection is perfectly accessible, it's just the itunes store that shows the error message. I have unchecked the 'check for server revocation' box in internet options and restarted, and have checked my date and time are correct. I've tried to use a root certificate update as suggested in older threads but can't find one accepted as 'current' to run.
Any help appreciated, I really really need to update my iPhone, still on version 4.3.3 : (
Thanks!

Go to Settings > App Store
Tap on your Apple ID
Sign out
Sign back in with the correct ID and password.
Then reboot your iPad: Press and hold BOTH the power and home buttons at the SAME time for about 10 seconds until the Apple Logo appears, then let go of both buttons and your iPad will restart. You won't lose any data or settings.
See if you can use the App Store normally after your iPad comes back up.

Getting NVIDIA RIVA TNT2 to work?

Similar Messages

Maybe you are looking for