Getting remote control 438483-001 to work in Windows 7

I have recently upgrade from Vista to Windows 7 premium (clean install).
Now my remote control which came with my dv9770ea laptop (P/N 438483-001) does not work. Batteries checked, the remote's green light flashes when pushing a button, AND when using Windows Media Centre the image/sound stalls for a split second when pushing some of the buttons. The card remote RC1762302/00 that also came with the laptop does work without problems. Hence I am confused. Apparently the infrared receiver does work for the above two reasons. However I'd like to use the remote and expect I need a driver update for it.
Any suggestions?
Cheers

All,
I've found the following solution for my problem, through the following thread:
http://h30434.www3.hp.com/t5/Operating-systems-and-software/Quick-play-buttons-on-Windows-7/td-p/147...
1) Install HP Quickplay quick launch buttons from HP website:
ftp://ftp.hp.com/pub/softpaq/sp39001-39500/sp39425.exe
2) Install the following driver:
sp40139.exe
downloadable from:
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-64317-1&lc=en&dlc=&cc=us&os...
Best of luck and hope it works for you too!

Similar Messages

Getting remote control 438483-001 to work in Win7

I have recently upgrade from Vista to Windows 7 premium (clean install).
Now my remote control which came with my dv9770ea laptop (P/N 438483-001) does not work. Batteries checked, the remote's green light flashes when pushing a button, AND when using Windows Media Centre the image/sound stalls for a split second when pushing some of the buttons. The card remote RC1762302/00 that also came with the laptop does work without problems. Hence I am confused. Apparently the infrared receiver does work for the above two reasons. However I'd like to use the remote and expect I need a driver update for it.
Any suggestions?
Cheers

All,
I've found the following solution for my problem, through the following thread:
http://h30434.www3.hp.com/t5/Operating-systems-and-software/Quick-play-buttons-on-Windows-7/td-p/147...
1) Install HP Quickplay quick launch buttons from HP website:
ftp://ftp.hp.com/pub/softpaq/sp39001-39500/sp39425.exe
2) Install the following driver:
sp40139.exe
downloadable from:
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-64317-1&lc=en&dlc=&cc=us&os...
Best of luck and hope it works for you too!

Beats Audio Control Panel software not working after Windows 10 upgrade.

Beats Audio Control Panel software not working after Windows 10 upgrade. the Beats sound enhancement is useless in WIndows 10. When opening the Windows 10 sound properties I'm getting this box message: Auido enhancement problem Windows has detected the audio enhancement for the following device are causing problems: Speakers / Headphones (IDT High Definition Audio Codec) Woud you like to disable driver enhancement for this device? IDT High Definition Audio CodecBeats Audio Control Panel version6.10.6491.02013.11.2009:43:18 Please provide some kind of fix for this?

Well, it has been a long road on the Win 10 upgrade. At first I got the same error message as above, but after deleting the Dolby Advanced Audio v2 in Win 10 using Control Panel Programs and Features and rebooting, I got into the continual BSOD upon reboot. Here are the steps I took to at least get stable on Windows 10. First, I rolled back to Windows 8.1 using the advanced feature in the BSOD recovery options. Once back in Win 8.1, I deleted the Dolby Advanced Audio v2 using Add/Remove Programs in Control Panel. Then I downloaded the Win 10 update and re-installed it. Once that completed, I updated the Intel Graphics driver under the display adapters (on my G780 it is an Intel HD Graphics 4000, and the driver can be found at https://downloadcenter.intel.com/). Currently I am running version 10.18.10.4252 for my machine. Then, under the Device Manager, I updated the Conexant SmartAudio HD driver under the Sound, video, and game controllers. That driver is currently at 8.66.4.50 and was automatically downloaded from the web when I requested to update driver. I also changed several others settings such as Notify to schedule restart after updates are installed instead of automatic (under Settings --> Update & Security --> Advanced Options) and Do you want Windows to download driver software and realistic icons for your devices? --> No, let me choose what to do, never install driver software from Windows Update. After that, I shut down the machine, waited a moment and booted back up. I have no idea why this helped or if it is overkill, but I am stable and running without a fear of rebooting now. Hope this helps if someone else is having this same issue.

How can I get my hp Laserjet 1012 to work with Windows 7?

How can I get my hp Laserjet 1012 to work with Windows 7?

Here is a list of products that are not supported in the win7 OS. This product is listed there.
Products not supported in win7
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

I can't seem to get the Elements 10 loader to work with Windows 8.1. Is there a workaround?

I can't seem to get the Elements 10 loader to work with Windows 8.1. Is there a workaround?

Never mind. I figured it all out. Thanks anyway.

Why can't I get photo stream or icloud to work with windows vista?

Why can't I get photo stream or icloud to work with windows vista?

Have you tried quitting Pages completely, restart the iPad and then go back to Pages and see if they will upload?
Go to the home screen first by tapping the home button. Double tap the home button and the task bar will appear with all of your recent/open apps displayed at the bottom. Tap and hold down on any app icon until it begins to wiggle. Tap the minus sign in the upper left corner of the app that you want to close. Tap the home button or anywhere above the task bar. Restart the iPad.
Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button.

I am having trouble getting my Blutooth Magic Trackpad to work in windows 7 running through a bootcamp partition on my 2008 MacPro. Any ideas?

I am having trouble getting my Blutooth Magic Trackpad to work in windows 7 running through a bootcamp partition on my 2008 MacPro. Any ideas?

I installed the apple drivers and it works though unlike
in osx where it works from the start in windows I need to click it once before it begin to work

DVD Remote Control buttons don't work when using regular DVD player

I created a DVD using DVD Studio Pro (version 3.0.2) and am unable to navigate through any menus or buttons using the DVD players remote control. I can press the play button on the actual DVD player and play the movie. How can I fix this issue? Any suggestions would be helpful!
I never changed the default setting on the file I made and the DVD works just fine in the simulator as well as any computer DVD player. Also, is there a way to make sure the DVD will play on all DVD players even if it doesn't read burned DVDs?
Thanks for the help!

Not sure if I can add anything here - you're in good hands! I'd like to know how you constructed the menus - did you use photoshop layers for the background and overlay, or did you use a pict file? Are these motion menus or static?
About the compatibility - a burned disc will only ever be about 85% compatible with the number of DVD players out there, and if a DVD player states that it cannot read from DVD-R or DVD+R discs then it most likely won't play your disc. The only way to approach full compatibility is to have the disc replicated, but the cost of this usually means it is not worth while for anything less than 500 to 1000 discs at a time. If you are using DVD±R then all you can do is take steps to make sure the disc is as compatible as it can be, such as keeping the MPEG encode less than 7.5MBPS, using AC3 audio, not applying paper labels and so on.
Compatibility is getting better in general, this summer I have burned in excess of 90 individual projects on DVD-R (and duplicated each one up to seven times each) for playback on consumer players and only one came back (so far). When I looked at it there was a chunk missing from the surface of the disc, which probably explained the error!

Need Sceptre TV Remote Control code(s) that work with VZ P265v3RC -- the '335' code does NOT

Recently upgraded my TV's in my house with new Sceptre 40" and 50" TV's - thank you WalMart. Purchased in September 2014. (new / current Sceptre TVs).
All of the Verizon printed, online, and other documentation for the P265V3 RC (model RC2655005/01B) for Sceptre shows to use code '335'. I have tried the '335' code on both of the TV's and no worky at all.
Following the 'Quick Setup Guide-Verizon FIOS remote' steps (paper/PDF instructions with RC Manual):
I can successfully enter the '335' code as outlned in step 4... and 'The RED LED will blink twice and then stay on'. occurs. So far, so good.
Step 5 states, "5. Press and release the <CH +> button repeatedly until the TV turns off......." This happens perfectly... I can press the <CH+>> button a few times, and indeed, my TV turns off.
Now, onto Step 6: "Test that the remote control is programmed for your TV"..... can't get Mute, A/V, other keys to activate /. be recognized - even though I'm followijng "press and hold that key. Release it as soon as it works"
Does anyone have a working code for Sceptre TV's ??? The Verizon '335' code doesn't work for me.
I need the 'best code' anyone has found that works with new Sceptre TV's.... the 335 code that VZ recommends... no worky.

Robertop,
have you tried the following? The info below is found here
Turn on your TV and the FiOS TV Set-Top Box.
Make sure you can see live TV.
Press and hold the OK and FiOS TV buttons together then release both buttons.
The red LED light blinks 2 times and then stays on.
Press and hold the Play button.
The remote control tries a new TV code every second.
The red LED light blinks each time a new code is sent.
When the TV turns off, release the Play button immediately.
NOTE: Some TVs may respond slower than others. If necessary, you can press the Ch+ and Ch- buttons to go forward or backward one TV code at a time.
Test your remote to ensure it is working properly:
- Turn on the TV by pressing the TV button on your FiOS TV remote.
- Press the Vol+ and Vol- buttons to ensure that you can control the volume.
- Press the Mute and A/V buttons to ensure they work.
If any of these buttons do not work, press and hold that button. Release the button as soon as it works.
If all the buttons work, press OK to this TV remote code.
The red LED light blinks 3 times and then turns off. Your remote control is now programmed.

FIOS mobile remote control feature suddenly stopped working

The remote control feature in the new FIOS Mobile app was working superbly this morning and now it doesn't recognized either of my STBs. Any solutions?
Thanks

Some nokia made remotes have a small battery inside (the one that's supplied with the N95 does) and it may have run out.
If you don't want to open the remote to check then you should take it to a nokia care point/service centre.
Care points:
UK
http://www.nokia.co.uk/A4228006
Europe:
http://europe.nokia.com/A4388379
Asia-Pacific
http://www.nokia-asia.com/A4416070
Elsewhere:
http://www.nokia.com select your country, go to the support section, then select repair.

How do I get Photo Deluxe 3.1 to work with Windows XP?

I have recently upgraded my PC (used to have 98SE).
Since then, I cannot get Photo Deluxe 3.1 to work
I *DO NOT* want Photoshop - it's WAY WAY WAY too complicated for me.
Photo Deluxe 3.1 was great, did everything I wanted it to do, and was so simple that even George W. Bush could work it.
The features that I used are :
* Allowing a print screen image to be pasted with CTRL+C
* EASY cropping of photos
* Wash out of photos (for back inlays of CD mixes - the back inlay was a washed out version of the front inlay, with text over the top)
* BASIC, easy to do brightness & contrast controls
* EXPORT - so I can export any image to almost any format, particularly JPG
Ideally, I'd like to continue to use Photo Deluxe 3.1
If I REALLY must, I want a SIMPLE Photo Editor (IE, NOT Photoshop) that will do the things I did with Photo Deluxe.

For the tasks Jangly Mark describes, GIMP is certainly easy. It would take less than 10 minutes to discover/learn how to do these tasks in GIMP.
The only reason why GIMP may appear to be difficult to us is because we are accustomed to Photoshop's different controls and methods.
Here are some GIMP quick tips:
Cropping:
Press 'Shift-C' to start the crop tool. Draw box. Adjust Corners. Hit 'Enter'.
Creating a washed imaged:
Tools Menu->Color Tools->Levels
Adjusting Brightness and Contrast:
Tools Menu->Color Tools->Brightness-Contrast
Jangly Mark wrote:
How do I run Photo DEluxe 3.1 in compatability mode?
Find the EXE file (the program itself) in Windows Explorer, right click on it, find the 'Properties' contextual menu item, adjust there.

Problem getting Remote Control to work at

I've just installed an X-Fi Platinum and everyting went well. Sound works great.
I do have one problem. The remote does not seem to do anything at all. I DO have the batteries in it, and they ARE in the right way, but pointing it at the I/O reciever from inches away gets no response at all.
Now, I DID download the latest X-Fi driver from this site to install the hardware (rather than the installation CD). I checked the installation CD though for any additional software and found the Creative Media Source software. I installed that.
Still, nothing. The ports and volume knobs on the front of my I/O box work fine, so I do believe that is hooked up fine.
Is there some OTHER piece of software I am supposed to install? Or any other ideas?
worm

Nope, the installer does not work because it looks like it was DESIGNED to prevent you from installing it from outside of the installer application.
The Solution:
Uninstall the LATEST X-Fi drivers from the website here.
Insert CD Rom
Install the OLDER version of the drivers.
Evidently the 40MB download for the current drivers does not contain all the 'extra' programs that come with the driver on the CD. To make things worse, you cannot install the additional applications from the CD (there are no menu options for them).
However, when I install the X-Fi driver from the CD-ROM, then a TON of extra programs (including the CONSOLE!!!) got installed as well. I had no options which to install or not, it just does them ALL.
A couple of suggestions for Creative:
) Add ALL of the software required to run the hardware deli'vered in the box to the downloads/support sections here.
2) On your installation CD, seperate out your X-Fi DRIVER file from all of the extra files. Then someone can find the software they need to run thier hardware, without doing un-obvious things like uninstalling the newer driver and installing older ones with hidden software packages included (which were NOT included in the newer driver package)...
worm

CHECKED "Disable Remote Control Infrared Received" not working

Hi,
I have an iMac and an Apple TV in the same room. I want the remote for the AppleTV to stop controlling the iMac.
Yes, I have already checked the box in System Preferences/Security & Privacy/General/Advanced.
Yes I have clicked OK and closed the lock to prevent further changes.
But the remote STILL CONTROLS the iMac. Its annoying.
On another discussion forum, a user mentioned a file called "/Library/Preferences/com.apple.driver.AppleIRController.plist" which my computer in fact does not have. Does anyone know, with Mountain Lion 10.8.4, should I still have this file?
Any other ideas what might be causing this?
The remote works and is paired with the AppleTV. But its still changing the iMac.
Any help would be much appreciated!
Many thanks,
ponderosa_74

Sorry to ask, but did you Unpair the Remote when you disabled the IR receiver...?

Remote-control of a Mac server from Windows

What is the Apple recommended way to logging into a Mac Server from a Windows PC so that I can manage it? I have an iMac on my desk but that's for creating/testing images. My main PC is an HP laptop running Windows 7. I've got Real VNC setup but the number of times it just stops working and I have to reconnect is not funny. Logging in is a chore, too. 1st password to control screen, then login to server, VNC gets kicked out during screen refresh, have to enter 1st password again to get back in.
Is there an official RDP program like Windows has for managing Windows servers?

Hi
+"What is the Apple recommended way to logging into a Mac Server from a Windows PC"+
AFAIK there isn't one? Why would there be? Putting the shoe on the other foot Microsoft offers RDC for mac to control PCs. I don't see anything on the site stating it's the 'recommended' way?
+"Is there an official RDP program like Windows has for managing Windows servers?"+
Yes. It's called Apple Remote Desktop. You can't install it on a PC. Since 10.5 VNC Server and Client are 'built-in' for Server and Client OS as you already know. The protocol is actually VNC. RDP is Microsoft's proprietary name for it.
I've never had problems controlling any mac (server or client) using TightVNC, RealVNC or UltraVNC - there are others you could use and experiment with? Depending on the Windows OS and network environment you may have to experiment with all three before settling on one that works consistently. Perhaps the problems you're having are due to a misconfiguration? On the mac side enable Remote Management - not Screen Sharing. Go into the VNC options and enable the "Control Screen with Password Setting". Create a password but don't make it the same as the Administrator one.
AFAIK the logging in behaviour you describe is normal in my experience. I've not found it a chore on either a platform.
HTH?
Tony

I have iTunes 11.4 and Windows 7. Using iTunes on Windows 7, I get message that iTunes has stopped working and Windows will close the program and notify me if a solution is available. Same message for last two days. Anyone else getting this?

I have iPad 2, iPhone 5s, both with iOS 7.1.2. I use PC with Windows 7 and hard wire internet service and iTunes to update apple products; no wi-fi. I updated iTunes to v11.4 on 09/11/14. I ran Windows update on 09/10/14. I did not try to open iTunes on my PC until yesterday 09/16/14. I got the message: "iTunes has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available." I got the same message today. Does anyone know if this is a Windows problem and if a solution is coming or an iTunes problem? I can get iTunes on iPad and iPhone. All other programs PC are working correctly. I use Norton Internet Service on PC. I ran virus scans and repair/reinstall iTunes yesterday on PC.

Hello notime4,
The article linked below details some useful troubleshooting steps that can help stabilize iTunes on your computer.
iTunes for Windows Vista, Windows 7, or Windows 8: Fix unexpected quits or launch issues
http://support.apple.com/kb/TS1717
Cheers,
Allen

Getting remote control 438483-001 to work in Windows 7

Similar Messages

Maybe you are looking for