Getting Time Capsule to work with current network help?

Hey, I wanted to get my apple routers to work with my current fios router without replacing the fios router. I need to get ethernet available in my upstairs office so I plugged my airport express into the fios router in the WAN port and made the time capsule join the network and it won't work at all. any ideas on how I could accomplish this? I need DHCP to work as well, I am using a arduino dev board and need a ethernet port and a working dhcp on all routers to assign it an ip

If the AiPort Express is setup to "create a wireless network", then the Time Capsule must be setup to "extend a wireless network".
The Ethernet ports are enabled on the Time Capsule when it "extends"......but they are disabled if the Time Capsule is configured to "join" a wireless network.
So....Ethernet cable from the Fios router LAN <--> port to the WAN "O" port on the AirPort Express.
Configure the Express to "create a wireless network". This must be either the A1264 or A1392 version of the Express.
Configure the Time Capsule to "extend a wireless network". The Time Capsule must be located where it can receive a very good wireless signal from the AirPort Express.

Similar Messages

How Do you get Time Machine to work with a network drive?

I have not been able to choose a Drive for Time Machine on a Network Drive. The network drive is active and shown on my desktop. How Do I use it?

Correct. Back up to a network volume (other than Time Capsule) is not supported, so if you want to do it you have to use the command line to set something as shown in the article.
Another option you could do would be to create a large disk image file on the NAS device and mount it on your client and back up to that. You'd use Disk Utility to create a large (say, 200 GB) sparse image on the network storage and then double click it to mount it on your machine and set TM to back up to that. I could show you how to do this in 30 seconds but instructing it over a forum post... not so easy

What is the best way to get a time capsule to work with a new network name?

What is the best way to get a time capsule to work with a new network name?

Well it seems that you did not explain to us the full story. Did you change ISP's or something? Why would it not show up anymore?
What colour is the light on the time-capsule? If it's blinking amber, then you probably need to do a factory-reset. That should get it to show up again in AirPort Utility.

Can I use my Time Capsule to extend a current network? If so, How?

Can I use my Time Capsule to extend a current network? If so, How?

I want to use it wirelessly to extend the range of the network. I currently have an xfinity router as the main.
You may not have understood what I was trying to say above.
If you want the Time Capsule to extend wirelessly, then you must have an Apple router as your "main" router.
You have an xfinity router. You cannot use the Time Capsule to extend the range of an xfinity router wirelessly.

Time capsule doesnt work with telia bredband no wifi

Time capsule doesnt work with telia bredband no wifi. Time capsule and its wifi worked in the beginning, but now it doesnt. I have tried everything without success.

There is no question.. so if it is a statement of resignation.. then if under warranty and faulty Apple will fix it/replace it.. if not dead you will be given it back.
Are you using Lion? If so did you download 5.6 airport utility?
Plug the TC into a computer by ethernet.. hold in reset for 10sec.. and then redo the setup.
Give TC and wireless short names and no spaces and no special characters.. lock the wireless to manual a/n-b/g and fix the channels.
Then if it doesn't work most likely faulty. Otherwise it is just setup is wrong.

Thinking of purchasing an Apple Time Capsule to work with my new iMac. I only want it for general family use. Any comments?

Thinking of purchasing an Apple Time Capsule to work with my new iMac. I only want it for general family use. Any comments?

It should work just fine. You can see user reviews on Apple's web site, here is the URL:
http://store.apple.com/us/product/MD032LL/A/Time-Capsule-2TB?fnode=MTY1NDA0Mg

Time Capsule not work with appletalk printers connected via ethernet?

I have seen no definitive answers to this problem posted here or on support forum. Some have suggested (but Apple refuses to confirm) that Time Capsule does not support AppleTalk devices (particularly printers) connected via Ethernet to Time Capsule. Even the "Genius Bar" guys can't tell you for sure, but this is what they suspect also.
I am a 25 year Macintosh user. I have conducted numerous experiments on this problem. What follows is my analysis and work around.
I have found no way to connect AppleTalk printers to Time Capsule by an Ethernet network connected to the back of the Time Capsule. It just doesn't work. Forget all the posts about what to try. Especially forget about resetting your printer settings. Waste of time. This leads me to conclude that those who suspect that Time Capsule does not support AppleTalk printers connected on an Ethernet network are absolutely correct. It is a hardware or software deficiency. I do not know why Apple won't just publish this in their technical specs. It would save us users a lot of time and frustration.
Now the work around. The only thing that I have found that will work is to set up an Airport Extreme to extend the wireless network created with the Time Capsule. Plug your ethernet network into the Airport Extreme, NOT into the Time Capsule. I presume (but have not tested) that this works with an Airport Express as well. I did this with my old Airport Extreme that I had left over after buying my new Time Capsule. Now the printers show up again and print fine.
Please let me know what your results are if you try this.

The problem is caused by an interaction between the Airport Extreme Update 2008-004 and the TC 7.3 firmware. I swapped out my TC for my AirPort Extreme (which sat on a shelf unused since I bought the TC). It has version 6.xx of the firmware. Immediately I could see my printer when I wirelessly connect with my MBPro and can print from it. I put the TC back and then did an Archive and Install of 7.5 on my MBPro. I did every software update except the Airport Extreme Update 2008-004. I could see my printer and print to it! After cloning my HD, I then applied the 2008-004 update to 7.5.5. That broke the wireless printing again! I tried TC firmware 7.3, 7.3.1, and 7.3.2 but not go. It is clear that my computer is trying to communicate with the printer (lots of flashing lights on my LAN switch) but no successful handshaking. I restored my hard drive from the clone and I now I can print again. Final word: if you want to print from a wireless computer connection to an AppleTalk printer connected to TC's LAN do not apply the 2008-004 update to your computer. Apple: please fix this problem.

Cannot get Time Capsule to Work as anything but Airport

I have had this problem off and on for months and have never been able to resolve it. I have already reviewed all of the threads addressing this issue and none of them solved my problem.
My time capsule will not show up on my finder OR through airport. If I restart it 2 or 3 times, airport will find it at which point I will again reconfigure it to act as my back-up drive with time machine. However, immediately after the forced restart, my computer again fails to recognize it.
Notably, my wireless internet through time capsule always works. Essentially, my time capsule is nothing more than an airport as I can't use it with time machine OR as a server to store documents through my finder.

What OS is on the computer?
You can load 5.6 utility if you are running Lion or Mountain Lion as follows.
How to load 5.6 into later Lion & ML
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
Leave the package open on the desktop so you can see the file. AirportUtility56.pkg
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. If your Mac refuses to run the software, because it wasn’t downloaded from the Apple store, go to security in preferences and allow other software to work.. this is limitation of trade methinks. You can set back later if you like.
Now drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. in finder, open the new directory, drill down.. applications, utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall version 6 (now 6.3 if you updated) so don't try.. and you cannot or should not run them both at the same time.. although I have had no problems when doing so.

Why won't time capsule wont work with Lion?

My Time capsule stopped working I installed Lion
I get one of two error messages:
The backup disk image “/Volumes/Brian Dunk's AirPort wirel/Brian Dunk’s iMac (2).sparsebundle” could not be accessed (error -1).
Or
Cannot complete backup error 6584
Any ideas welcomed
Brian

The serial included with the TORRENT floating around the web for Logic 9 wont work on anything after 9.0.2
$100 says this is why said user is freaking on a simple update... just sayin

How can I get Time Capsule to work as a router

I currently have Verizon as my ISP and they installed a modem that's also a router. What do I do to get Time Capsule to override the router and become my router. I can't seem to do it.

try either one in bridge mode....the secondary router that is...

How do i set up time capsule to work with airport extreme base to extend wireless network?

i have a airport extreme base, how do i set up a time machine to extend the wireless network i have with airport extreme? i have also 3 airport express's connected to the same network to extend my wifi all over my house. thanks in advance.

Much better graphics, thanks.
You can leave the Time Capsule connected by Ethernet from the Linksys and configure for a "roaming" network as mentioned previously.
To do this, open AirPort Utility - Manual Setup
Click the Wireless tab below the icons
Wireless Mode = Create a wireless network
Wireless Network Name = Same name as the AirPort Extreme
No check mark needed next to Allow this network to be extended
Radio Mode = Same setting as the AirPort Extreme
Channel = Automatic
Wireless Security = Same setting as the AirPort Extreme
Wireless Password = Same password as the AirPort Extreme
Confirm Password
Click the Internet icon, then the Internet Connection tab
Connect Using = Ethernet
Connection Sharing = Off (Bridge Mode)
Update to save settings and allow the Time Capsue to restart
Then power down the entire network
Wait a minute or two
Start the modem first and let it run a full minute
Start the AirPort Extreme the same way
Power up the switch
Power up the Time Capsule for a minute
Keep starting devices one at a time about a minute apart
Now, your computer will automatically pick up a wireless signal from either the AirPort Extreme or Time Capsule, whichever device is closer and providing the stronger signal.

HT1175 3TB time capsule not working with new iMac

I have a 3TB time capsule that's c. 2 years old. It worked perfectly with my old iMac. I bought a new 27" one when it came out this year and since the time capsule will not work.
I had to clear all the data as a starter. Now it gets a little into the backup taking c. 1 day then resets. It's connected via ethernet cable and has been told to join an existing network.
Currently it says it's backing up 922,498 items, after 2 hours (this is the third attempt, it resets then has no record of the old backup) it says 10kb of 789.44 GB - About 4,664,440 days remaining!!
To clarify I'm trying to use Time Machine with the Time Capsule.
Please help!!

You have made a mistake in the setup.
You do not "Join an existing networking" and use ethernet.. they are mutually exclusive.
What you are doing is backing up over double hop wireless which is slowing to a crawl.
You need to put the TC into bridge mode.. and plug it into the main router by ethernet. Then use wiretess to the TC if you are too far away or ethernet if you are close by..
As soon as you put the TC into join a wireless network it deactivates the ethernet.

Time Capsule Not Working With Time Machine

I'm trying to backup to my Time Capsule, which I haven't used in over two years. It had been displaced because of a change in internet service providers. The new provider came in with a Linksys router, setup a sub-network, and left the Time Capsule/Airport out of the mix.
So I want to return to using my Time Capsule and have since pulled out the Linksys router, and got the Airport functionality working with the existing, primary network. In other words, the Time Capsule/Airport is working to extend the range of the network.
Problem is this: I cannot backup to the Time Capsule. Even if I'm connecting to the Time Capsule via ethernet, I cannot get it past the 'preparing' phase when running Time Machine. It stays at the phase for what seems to me an inordinate amount of time (30-45 minutes). If I go into System Preferences, the Time Capsule disk doesn't make itself available when using it with Time Machine. If I choose to go into the Star Wars display of Time Machine, I can sort of see the various backups, but I can't roll back to them, and the backup indicator on the right looks sort of ghosted, like it's there but it's not there.
How do I know if the disk within the Time Capsule is failing? Could that be what's going on? How would I test it? I get a green light on the front of the TC, but not everything is hunky dory since I'm not able to backup.
Is part of my problem that I'm using a not up-to-date version of Airport Utility? –I'm using 5.4.2

Oh and here it is, on this page, Section D, #1:
"Section D. OTHER PROBLEMS RUNNING BACKUPS
D1. Stuck in "Calculating changes" or "Preparing""
and then the Apple supporting doc, as well:
http://support.apple.com/kb/TS1516
Fabulous. Thank you.

Is it possible to configure Time Capsule to work with Time Machine (MBP) and Genie Timeline (PC)

I have an Apple Time Capsule (2TB) and I need to configure it to work with my MBP and Time Machine and also back up my a PC with Genie Timeline Pro 2013 (or any other suggested PC back up software).
Setting it up to work with Time Machine is simple enough but the PC access is proving to be difficult.
http://www.genie9.com/support/KB/KnowledgeArticle.aspx?KBID=198
I followed the above steps but still can't connect to the network drive. I have reformatted the TC and will be walking through the steps again. My concern is that the two different operating systems (Win8 and Mavericks) can't share the same destination drive.
I have created two user accounts with drive sharing activated. One in my name for my MBP and the other in the name of my partner for her Dell laptop.
Should the Time Capsule be partitioned? Can it even be partitioned? When I use Drive Utility it can't see the TC. The only way to connect to it seems to be via Airport Utility.
On a seperate note the TC Router Mode is set to OFF (Bridge Mode). I have connected it to the ADSL modem/router (WiFi Off) via the WAN port. All seems to be well. Am I loosing any useful functionality by doing this?
The internet settings are set Connect Using DHCP. I have no issues but I am not really sure what it means and if I should be using other settings. The ADSL modem/router seems to have all the PPP0E settings.
The WiFi on the TC has been set up with a 5Ghz and 2.4Ghz network as well as a Guest Network. I then plan to introduce 2 Airport Express (MB321LL/A). One will be an access point for AirPlay and the other a wireless extender with AirPlay.
There is also a Canon WiFi printer that accesses the 2.4Ghz network. It has an Ethanet port so I am wondering if I should disable the wifi connection and cable it and if so to the TC or the DSL modem/router.

Lion, 7.6.1 firmware and iCloud offers remote access.
http://www.apple.com/au/support/icloud/back-to-my-mac/
To do it without the iCloud service your issue is static public IP address.. if you have one this is simple to the point of trivial. If not it is very hard, as Apple did not put in a standard dynamic DNS service.. (ensuring you were roped into their cloud accounts). Static IP from your ISP is the best solution.. if it is possible go for it.
Then the actual protocol for access is AFP, so the only device you can do this on is a Mac.
Do you have the TC as the main router?
If you want any other kind of access, or to avoid icloud use vpn.. which teamviewer is a kind of.. but buy a real vpn router, and bridge the TC.. you can then vpn into your network with full security and get windows access via smb..

How do I configure Time Capsule to work with 8 port unmanaged switch?

This is what I want to end up with.
cable modem
Time Capsule
wireless network 8 port unmanaged switch TRENDnet TEGS80G
entertainment center(TV, xbox 360, dvd, apple tv, ect...)
I have been using the above setup with an E3000 router in place of the time capsule without any problems, and was expecting to just be able to switch out the E3000 for the time capsule and keep right on rolling. At the moment, without the switch plugged in, using the time capsule as a stand alone wireless router, everything works as intended. However, I don't want to have every device in the house pulling off of wireless. Whenever I plug my switch in I lose internet connectivity. I assume this is because both the switch and the Time Capsule are trying to direct traffic and creating a conflict. I have attempted to disable the NAT in the Airport Utility and this is what happens.
Where do I go from here, or am I heading in completely the wrong direction?

Unfortunately, you are on the wrong track, heading in the wrong direction at the moment.
We need to learn whether you have a simple modem or a modem/router.
This will determine whether the Time Capsule is to be configured in router mode to provide DHCP and NAT services for the network......or if your "modem" is already doing this.....the Time Capsule needs to be configured in Bridge Mode.
So, I suggest that you disconnect the switch from the Time Capsule for now, and power everything off except the modem, Time Capsule and the computer you are using to configure the Time Capsule, and get things working correctly first. Then, devices can be added one at a time to verify proper operation.
If this seems to make sense to you, and you want to move forward, please post back with the make and model number of your cable modem.

Getting Time Capsule to work with current network help?

Similar Messages

Maybe you are looking for