Gigabit Reversed???

MSI K8N NEO2 Platinum bios 1.4 (official)
I didn't have any trouble using either network atapter but was having so much trouble getting my system stable, that I updated the drivers for these along with everything else.
When I did update, my Realtek Gigabit NIC dropped to 10/100, and my NVIDIA nForce all of a sudden is now showing up as 10/100/1000 on my switch, and the plug light turned from green to red. (showing gigabit speed)
Any Idea what went wrong?
I also can't get my Corsair XMS (ULL) twin 2x512 to run at 2-2-2-5 (SPD) without showing all kinds of errors in memtest86. Will this board just not work with this ram at this speed? I can get to run at 2.5-3-3-6, and no errors but I sure didn't need to pay the extra bux for this ULL ram if I can't even use it right?

Quote
Originally posted by BillyD
I don't know about the first problem, but to get your Corsair to run those timings you need to have the Voltage up above default voltage levels. The default in the BIOS is 2.65V and Corsair says the memory is tested at those timings at 2.75V. you can see for yourself here. All the 2-2-2-5 memory I have seen from any manufacture is running it at above stock voltages
Thanks!
I actually have tried both 2.75V (minimum suggested for this Corsair ram) and 2.8V as suggested by the Ram Guy at Corsair. Running at 2.8V I could drop it to 2-3-3-6, instead of 2.5-3-3-6. Could there be a problem with my CPU? How do you test for that?
NOW my Gigabit connection is available on BOTH ports??? I just updated the Realtek driver that was posted at Realtek, and now show 10/100/1000 again from the Realtek adapter. I also still show 10/100/1000 running across my Nvidia nForce adapter too. What is going on???
Grounding problem? When I was installing the board I might have over bent the I/O shield tab that covered the Ethernet ports. If this tab doesn't touch the frame of the port could this cause a grounding problem?

Similar Messages

Gigabit ethernet only supports 100Mb

Hi
Im having a problem with the 48-port Gigabit ethernet blade (48-port 10/100/1000BaseT (RJ45)) on a 4506 switch, one of the ports only support 100Mb, if hardcoded to 1000Mb on both sides, then the connectivity would be gone. All other ports on this blade seem fine.
Would it be a hardware issue? Any idea what caused it?
Thank you
Jane

Not at this point, no.
Any diagnostics, with or without testing equipment, are going to require disconnecting either or both ends of the cable.
You can follow the cable through the system and inspect all of the connections (patch cable->panel->info outlet->patch cable to the host), maybe try re-punching the connection at the panel to make sure the wires are seated into the IDC connector.
You'd be looking primarily at the blue and brown pairs (green and orange are used for Ethernet/Fast Ethernet).
Likely as not, one of the blue or brown pair are reversed (i.e., white-blue and blue are swapped at the panel).
If that's the case, you'll need to clear and re-punch the pair.
Good Luck
Scott

Am I getting Gigabit transfer between WRT610N router and NMH410 Media Hub?

Shouldn't the ethernet port LED be flashing blue (gigabit connection) between these 2 connected devices? It's flashing green which, according to the router manual, suggests a 10/100 port. I'm sure I'm missing something!

If you are refering to the Manual of WRT610N about the Light status, You need to reverse the light status. As per the Linksys manual The LED lights up Green when it is connected to 10/100 port and Blue when it is connected to a gigabit port. But in real terms which you need to revers this, Green light for Gigabit and Blue light for 10/100 port.

Dedicated Gigabit link between v880s

I would like to set up the ge interface on two v880's to be a dedicated gigabit link between them. However, I am having problems getting the link up. Here are the steps I have taken (on both servers):
1. connected ge interfaces with 50/125 fiber cable
2. vi /etc/hostname.ge0
3. vi /etc/hosts
4. ifconfig plumb ge0
5. ifconfig ge0 inet 192.168.10.x netmask 255.255.255.0 up
Following this, I can ping the local interface on each server, but I cannot ping the interface across the fiber. Here is the output of my ifconfig -a:
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
eri0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 10.0.100.33 netmask ffffff00 broadcast 10.0.100.255
ether 0:3:ba:44:b1:f4
ge0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 9
inet 192.168.10.2 netmask ffffff00 broadcast 192.168.10.255
ether 0:3:ba:44:b1:f5
I notice that "RUNNING" is not present in the flags for the ge0 interface on either server. Should this be reason for concern. I have not done a reboot of the servers, but I don't think that should be necessary since these servers should have dynamic config.
Any ideas of what I am doing wrong?

If you are connecting the servers without a switch on oneof the server you need to reverse the connection.
regards

How do I use Sun Web Server 7.0u1 reverse proxy to change public URLs?

Some of our installations use the Sun Web Server 7.0 (update 1, usually)
for hosting some of the public resource and reverse-proxying other parts
of the URI namespace from other backend servers (content, application
and other types of servers).
So far every type of backend server served a unique part of the namespace
and there was no collision of names, and the backend resources were
published in a one-to-one manner. That is, a backend resource like, say,
http://appserver:8080/content/page.html would be published in the internet
as http://www.publicsite.com/content/page.html
I was recently asked to research whether we can rename some parts of
the public URI namespace, to publish some or all resources as, say,
http://www.publicsite.com/data/page.html while using the same backend
resources.
Another quest, possibly related in solution, was to make a tidy url for the
first page the user opens of the site. That is, in the current solution when
a visitor types the url "www.publicsite.com" in his or her browser, our web
server returns an HTTP-302 redirect to the actual first page URL, so the
browser sends a second request (and changes the URL in its location bar).
One customer said that it is not "tidy". They don't want the URL to change
right upon first rendering the page. They want the root page to be rendered
instantly i the first HTTP request.
So far I found that I can't solve these problems. I believe these problems
share a solution because it relies on ability to control the actual URI strings
requested by Sun Web Server from backend servers.
Some details follow, now:
It seems that the reverse proxy (Service fn="service-passthrough") takes
only the $uri value which was originally requested by the browser. I didn't
yet manage to override this value while processing a request, not even if
I "restart" a request. Turning the error log up to "finest" I see that even
when making the "service-passthrough" operation, the Sun Web Server
still remembers that the request was for "/test" (in my test case below);
it does indeed ask the backend server for an URI "/test" and that fails.
[04/Mar/2009:21:45:34] finest (25095) www.publicsite.com: for host xx.xx.xx.83
trying to GET /content/MainPage.html while trying to GET /test, func_exec reports:
fn="service-passthrough" rewrite-host="true" rewrite-location="true"
servers="http://10.16.2.127:8080" Directive="Service" DaemonPool="2b1348"
returned 0 (REQ_PROCEED)My obj.conf file currently has simple clauses like this:
# this causes /content/* to be taken from another (backend) server
NameTrans fn="assign-name" from="/content" name="content-test" nostat="/content"
# this causes requests to site root to be HTTP-redirected to a certain page URI
<If $uri =~ '^/$'>
    NameTrans fn="redirect"
        url="http://www.publicsite.com/content/MainPage.html"
</If>
<Object name="content-test">
### This maps http://public/content/* to http://10.16.2.127:8080/content/*
### Somehow the desired solution should instead map http://public/data/* to http://10.16.2.127:8080/content/*
    Service fn="service-passthrough" rewrite-host="true" rewrite-location="true" servers="http://10.16.2.127:8080"
    Service fn="set-variable" set-srvhdrs="host=www.publicsite.com:80"
</Object>
I have also tried "restart"ing the request like this:
    NameTrans fn="restart" uri="/data"or desperately trying to set the new request uri like this:
    Service fn="set-variable" uri="/magnoliaPublic/Main.html"Thanks for any ideas (including a statement whether this can be done at all
in some version of Sun Web Server 7.0 or its opensourced siblings) ;)
//Jim

Some of our installations use the Sun Web Server 7.0 (update 1, usually)please plan on installing the latest service pack - 7.0 Update 4. these updates addresses potentially critical bug fixes.
I was recently asked to research whether we can rename some parts of
the public URI namespace, to publish some or all resources as, say,
http://www.publicsite.com/data/page.html while using the same backend
resources.> now, if all the resources are under say /data, then how will you know which pages need to be sent to which back end resources. i guess, you probably meant to check for /data/page.html should go to <back-end>/content/page.html
yes, you could do something like
- edit your corresponding obj.conf (<hostname>-obj.conf or obj.conf depending on your configuration)
<Object name=¨default¨>
<If $uri = ¨/page/¨>
#move this nametrans SAF (for map directive - which is for reverse proxy within <if> clause)
NameTrans.. fn=map
</If
</Object>
and you could do https-<hostname>/bin/reconfig (dynamic reconfiguration) to check out if this is what you wanted. also, you might want to move config/server.xml <log-level> to finest and do your configuration . this way, you would get enough information on what is going on within your server logs.
finally,when you are satisfied, you might have to run the following command to make your manual change into admin config repository.
<install-root>/bin/wadm pull-config user=admin config=<hostname> <hostname>
<install-root>/bin/wadm deploy-config --user=admin <hostname>
you might want to check out this for more info on how you could use <if> else condition to handle your requirement.
http://docs.sun.com/app/docs/doc/820-6599/gdaer?a=view
finally, you might want to refer to this doc - which explains on ws7 request processing overview. this should provide you with some pointers as to what these different directives mean
http://docs.sun.com/app/docs/doc/820-6599/gbysz?a=view
>
One customer said that it is not "tidy". They don't want the URL to change
right upon first rendering the page. They want the root page to be rendered
instantly i the first HTTP request.
please check out the rewrite / restart SAF. this should help you.
http://docs.sun.com/app/docs/doc/820-6599/gdada?a=view
pl. understand that - like with more web servers - ordering of directives is very important within obj.conf. so, you might want to make sure that you verify the obj.conf directive ordering is what you want it to do..
It seems that the reverse proxy (Service fn="service-passthrough") takes
only the $uri value which was originally requested by the browser. I didn't
yet manage to override this value while processing a request, not even if
I "restart" a request. Turning the error log up to "finest" I see that even
when making the "service-passthrough" operation, the Sun Web Server
still remembers that the request was for "/test" (in my test case below);
it does indeed ask the backend server for an URI "/test" and that fails.
now, you are in the totally wrong direction. web server 7 includes a highly integrated reverse proxy solution compared to 6.1. unlike 6.1, you don´t have to download a separate plugin . however, you will need to manually migrate your 6.1 based reverse proxy settings into 7.0. please check out this blog link on how to set up a reverse proxy
http://blogs.sun.com/amit/entry/setting_up_a_reverse_proxy
feel free to post to us if you need any futher help
you are probably better off - starting fresh
- install ws7u4
- use gui or CLI to create a reverse proxy and map one on one - say content
http://docs.sun.com/app/docs/doc/820-6601/create-reverse-proxy-1?a=view
if you don´t plan on using ws7 integrated web container (ability to process jsp/servlet), then you could disable java support as well. this should reduce your server memory footprint
<install-root>/bin/wadm disable-java user=admin config=<hostname>
<install-root>/bin/wadm create-reverse-proxy user=admin uri-prefix=/content server=<http://your back end server/ config=<hostname> --vs=<hostname>
<install-root>/bin/wadm deploy-config --user=admin <hostname>
now, you can check out the regular express processing and <if> syntax from our docs and try it out within <https-<hostname>/config/<hostname>-obj.conf> file and restart the server. pl. note that once you disable java, ws7 admin server creates <vs>-obj.conf and you need to edit this file and not default obj.conf for your changes to be read by server.
>
I have also tried "restart"ing the request like this:
NameTrans fn="restart" uri="/data"
ordering is very important here... you need to do this some thing like
<Object name=default>
<If not $restarted>
NameTrans fn=restart uri from=/¨ uri=/foo.
</If>

How to ensure that an accrual (FBS1) that was cleared and reversed/reset (FBRA) does not affect the books while being in open items (FAGLB03)?

At first the user created an accrual using FBS1 for reversal on 5/1/2015.
This created a clearing document.
Then it was mistakenly reversed by the user for 5/1/2015 by using F.81
This also created a clearing document.
Based on advice in the following thread: Delete reverse accrual/defferal documents | SCN ,
the user used FBRA to reset and reverse the document. We are unsure if the reset and reverse command was used or just the reset choice.
Now the accrual value is in the respective accounts with an open status (i.e. red button). Does this mean that the entry has already been discarded and it won't affect the accounts? Or does one then use FB50 to reverse the effects of the accrual in the current and next month?

Hi
I guess that the user has not reverse the transaction as its still shows as open item in 30 /4 .. so I belive that you need to use fb50 or simply use FBR2 and enter the original entry no and the choose (generate reversal posting option )..
regards
mahmoud el nady

Miro Reversal and GR IR Clearing

Dear Friends,
Once Migo and Miro is done and subsequently the miro is reversed while doing auto clearing of GR IR Account, the system is knocking off the original migo and the original miro and leaving the reversed miro as open item instead of clearing the original miro against the reversal miro.
Is this a standard functionality due to cenvat issues or is there some other problem.
Please advice how to take care of the same.
Regards
Mukesh

This is standard only.
When cenvat is there it should be very carefull at the time of MIRO and reversal of same in the same month.
Manual clearing of MIRO & reversal of MIRO documents

DNS: reverse zone comes back after remove and some follow up issues

hello community,
after installation of OSL i had setup dns with a primary zone.
the automatically created reverse zone for my internal network is fine.
whenever i enter a new system the default for the ip address is 10.0.0.1 and the reverse zone is automatically setup for this ip address.
whenever i remove this reverse zone it come back automatically after saving the dns configuration.
with this come some follow up error.
server admin claim that there is no name server configured for this reverse zone.
when i configure it the configured name server entry vanished after clicking the save button.
when i try to configure settings i can not. i get the error message that the configuration can not be saved cause of the missing name server for the reverse zone i am not using ....
in the log file i can see that the file for reverse zone can not be found.
when i check the dns configuration in the shell i can see that the reverse zone file is not there.
someone has an idea
- whats the best way to fix this?
- why is the gui still showing the reverse zone i am not using?
- is the dns configuration also in the ldap db with wrong entries?
regards
christian

Clean out your zone definitions, and start over. Server Admin is unfortunately seemingly fussy around the authoritative server stuff and the order stuff gets entered, and it seems you can get into a sequence where it doesn't have what it needs. I had encountered couple of cases when I was in a similar state as you're in now, and I ended up clearing and deleting the primary zone and re-adding the zone and the hosts, being careful to add the authoritative server as the first step of adding a zone.

View iCal's day and week view in reverse chronological order

Greetings iCalers,
When I think about day/week calendars, with the Y-axis being times of the day as in iCal's day/week views (e.g. "3:00 AM", and "5:00 PM" are in the leftmost column), I think about times building up to midnight from the bottom—i.e. the day starts at 12:00 AM on the bottom, with 1:00 AM above that, and the day ends with 11:59 PM on the top. I've learned that this intuition is atypical, and all calendaring systems I've come across work in the reverse direction, in line with the majority of people's intuitions.
I'm wondering if there's a way to get iCal to display in the reverse-chronological order. I suspect there isn't, and I've never seen a terminal command or apple script for it, but I'm hoping there is. If anyone know and could post it here, that would be great!
Thanks!
-Scott
Message was edited by: scottclayton

It's cool, I figured out a solution: get over it and stop worrying about trivial issues to the point of excessive fussiness.

AT a remote hotel I was asked to revert to a more simplified version of Yahoo. How do I reverse that?

I have a very simple version of Yahoo mail and would like to revert back to my original with all the bells and whistles. I was asked to do this when at a remote hotel and the internet connection was poor. Now I 'd like to reverse this.

hello, what you could try to do is to [[Clear the cache - Delete temporary Internet files to fix common website issues|clear the cache]] & [[Delete cookies to remove the information websites have stored on your computer|cookies from yahoo.com]] and reload the page.
in case this doesn't help please contact yahoo's support since it is likely caused by a setting tied to your yahoo account...

Error while creating 2nd Material Receipt after reversal of 1st MR

Dear,
Facing an error while creating Material Receipt.
The gate entry of this material is 123456789.
The 1st MR was created on 10/02/2011 & no. was 12345 with Location ABC via Z T-code.
Under Quality this product was Rejected with Location XYZ.
Due to Material was Rejected in Quality this MR 12345 was reversed through MB01 which produced a Reversal number 67890.
Now the material is again on its original Location ABC.
Now when the user is again creating an MR on 17/03/2011 of this material present at ABC location via using Z T-code it is producing an error stating that M/R already processed against 123456789 gate entry.
We have done these several cases before also and there was no error shown when we created the 2nd MR for the same material after its reversal has been made.

Dear,
Problem solved.
The problem was in PO.
The person had unchecked the GR-basediv which caused the real trouble. The MR number was not appearing in MB03 & material was rejected in the QA11 so it was reversed through MB01.
When again the MR was being punched then it was stating that the "MR already processed for the Gate Entry."
PO was changed, Bill No. was changed by adding "A" & later deleting this "A" from Table level.

Resetting and reversing a cleared document

Hello
I want to reset and reverse a customer clearing document. The clearing document which is 54203512 was posted and matched against the customer invoice in the previous period. When reversing and resetting the document in transaction code FBRA, a pop up screen u201CReversal Datau201D appears. The reversal reason is specified as 01 (Reversal for incorrect posting), posting date is todayu2019s date however the original clearing document 54203512 was posted in 05.09.2008 and in previous period. Click on continue.
The document is not reset and reversed and I am getting the error message u201CReversal reason 01 only permits posting date 05.09.2008u201D. Not sure why the document is looking at the posting date of original document even though I specified the reversal date as 08.10.2008. Can a document be reset and reversed in different periods?? Or does this cause any issues or problems? Or is this a bug??
Thanks in advance
Evelyn

Hi,
There are only 2 controls allowed for Reversal reasons:
1. Negative posting
2. Alternative date for posting
The symptom you have mentioned would be of a control from somewhere else, i.e. either a user exit or a validation. An order reason can only restrict it to current date or allow any other date. At least that is what I have experienced.
Cheers...

My ipod touch 2 no longer recognizes or syncs new playlists from my computer. But it does takes the playlists from the ipod and syncs to the computer. This is a reverse process - what am I doing wrong? It always synced the correct way in the past.

Why doesn't my ipod touch 2 recognize or sync new playlists from my computer? It did in the past, but now the syncing process goes in reverse; the
playlists on the ipod touch 2 sync to my computer!

Was the iPod previous synced to another iTunes library/computer?
Have you successfully synced from this iTunes library/computer before?
If so have you done anything like update iTunes on the computer since it last successfully synced?
Do the songs play in iTunes?
Does any media now sync to the iPod?
Do you have the right boxes checked to sync?
iTunes: Syncing media content to iOS devices and iPod
Try syncing using the manual method
Managing content manually on iPhone, iPad, and iPod
- Backup and then restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.

Credit memo link with Goods reversal

Hi,
Does anyone know of any process or method either in R/3 or in SRM that can be used to link Goods reversal with automatic credit memo creation for a PO ( when invoice is already posted ). We have SRM 4.0 and not using GRBasedIV status checked for most of the POs.
Can a customized movement type or workflow achieve this.
Thanks in advance,
Viv

Again I can tell you that the process what you were following (reversing the goods receipt) is totally wrong and it will have a serious negative impact on inventory. Either you should not create a return delivery or take the stocks into parent plant. If you dont want to show in inventory, then scrap it which is a standard process.
Coming to the requirement, there is no standard way to achieve this. Check these threads where the same topic was discussed
[Re: How to set up in SAP to have automatic billing after PGI |Re: How to set up in SAP to have automatic billing after PGI]
[automatic billing|automatic billing]
You have to apply the same logic for credit note also.
thanks
G. Lakshmipathi

I have just updated to iOS7, no icon for browser, was using Safari, how do I get it back and can I reverse the upgrade and go back to iOS6?

I have just updated to iOS7, no icon for browser, was using Safari, how do I get it back and can I reverse the upgrade and go back to iOS6? Thanks to you from the UnTechie

The icon for Safari has probably moved to make room for new apps. Scroll the Home screen to look for it.
You cannot reverse the upgrade.

Gigabit Reversed???

Similar Messages

Maybe you are looking for