Giving IP address and DCHP to aironet 1250

hi,
We need to give an ip address to 1250 just for the managemnt purpose ( similar to VLAN1 ip address given in case of L2 switches ). And then Aironet1250's gigbit ethernet will be connected to our Core L3 4507 swicth which has DHCP running. And will distribute the IP address to wireless clients. In this case how to configure an ip address and also have DHCP running. Management IP adress is not in the range of the DHCP pool. so in case any configuration is required on Aironet device we will connect a notebook with a same subnet ip address as that of Aiornet device , and then telnet / ssh to management IP of aironet devive.
Any experience pls share.
Any configuration link on cisco.com is appreciated.
Thanks in advance.
Subodh

Aironet devices can not have a management IP address. Following links may help you
http://www.cisco.com/en/US/docs/wireless/access_point/350/configuration/guide/ap350ch9.html
http://www.cisco.com/en/US/docs/wireless/access_point/12.3_7_JA/configuration/guide/s37adm.html

Similar Messages

Cisco Aironet 1250 - How to bridge two AP's and get Non-root to talk to Root AP

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin-top:0in;
mso-para-margin-right:0in;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0in;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:Arial;
mso-bidi-theme-font:minor-bidi;}
      I have two buidlings acroos the street from each other. I have two Cisco Aironet 1250 wireless AP's with the first one going in the main building with network backbone. The Second AP goes across the street with the other wired network segment. Both AP's have long range antenas 2.4 GHZ on top of each building. I have configured the 1st one as the Root Bridge. The one across the street is configured as non-root bridge. I have both AP's configured with the same WEP key and also with the same SSID name with both set to broadcast it.   I am still unsure and confused as to how I get the non-root bridge to talk to and use the root bridge to get on the main network.
        1- It’s main to use the Root parent Mac address.
        2- Is there another config that I am missing to get the signal?
Note: I still not getting any signal from the root although distance between root and non-root is 330m
My root antenna is AIR-ANT24120 and non-root antenna is AIR-ANT1949 and attached files is my configuration files
Thank you.

1. How are the AIR-ANT24120 and the AIR-ANT1949 installed?
the AIR-ANT24120 is connected virtically on tower far 11m from the earth and AIR-ANT1949 is connected horizontally on tower far 10m from the earth
2. What is the distance between both APs?
350 m
3. Do you have clear line-of-sight between the two?
there is one tanker in the middle between them but it's far 7m from the earth
4. Is the two APs properly aligned?
i think yes and changed the aligned many times without any news (I don't have any tools for alignment)
5. Which point are the antennas connected to? Primary, Secondary or middle?
I tried in the primary and secondary but never tried the middle antenna
Thanks

Cisco Prime Infrastructure 1.2 and Aironet 1250 + VSS issues

Hi,
I am new to the NCS implementations and configurations. I have one very specific case with Cisco Prime Infrastructure 1.2 and autonomnous APs and several issues with Cisco VSS on 6500 switches.
So here is the version from Prime:
NCS/admin# show version
Cisco Application Deployment Engine OS Release: 2.0
ADE-OS Build Version: 2.0.1.038
ADE-OS System Architecture: x86_64
Copyright (c) 2005-2010 by Cisco Systems, Inc.
All rights reserved.
Hostname: NCS
Version information of installed applications
Cisco Prime Network Control System
Version : 1.2.1.012
IOS version on our APs (which are autonomnous) is:
AP-N-1>show ver
Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(25d)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 11-Aug-11 03:23 by prod_rel_team
Well the issue what we have now is that access point has been added but its not recognized by the NCS prime. I have tried all three versions of SNMP but I get the same result. The SNMP configuration is valid since I use the same for my switching infrastructure. When I enter "debug snmp packets" and "terminal monitor" I can see the SNMP communication between Prime and Aironet 1250 which is standalone.
When I switch to Lifecycle theme and go to Operate > Device Monitor Center I see all devices I have added. The Aironet 1250 is reachable but under collection status I get Managed with Warnings. When I hover over with my mouse I get "None available".
I have successfully added my switching infrastructure in total, which is operating perfectly for Catalyst 2960/3650/3750/4500 series but for 6500 under VSS I have some warnings. The device is recognized by the system which is excellent and all is operational. I get the following errors under Collection Status:
feature_sensor
SNMP request timed out
feature_powerSupplyFanStatus-6k
SNMP request timed out
IdentityCapability
The device is unreachable.
feature_flashdevice
SNMP request timed out
sam_ipsla_feature
The device is unreachable.
What can be done to resolve these issues ? I have attached a screenshot of this particular issue. The affected access point is 172.16.165.241.
Predrag Petrovic

Hi rajeeshp,
Currently I am not allowed to upgrade it because of internal procedures involved in upgrading a specific piece of software (obtaining permissions from various departments). Is it free to upgrade from 1.2 to 1.3 or there is a specific charge for that.
Predrag Petrovic

Changing the multicast Address and Port giving error

I am using Coherence 3.3.1 jar files (Coherence.jar and tangosol.jar) in my local application. But when I try to change the multicast Address and Port in tangosole-coherence.xml(in Coherence.jar) then it is giving this error -
"This member could not join the cluster because of an incompatibility between the cluster protocol used by this member and the one being used by the rest of the cluster. This is most likely caused by a Coherence version mismatch, or by mismatched protocol filters (e.g. compression, or encryption)"
If i am using unique IP and Port then how can it be in a Cluster as this error stating. Please reply ASAP.

Hi,
There is a good chance that there is already the IP and port is being used by another cluster (which uses different versions of jars or configurations) and hence, when you are starting your cluster, throwing the error.
Can you double check if another cluster is already using it or not ?
Thanks,
Amit

4 Aironet 1250's and a controller?

Hi guys,
I'm about to order a four Aironet 1250's and a 2106 Wireless LAN Controller. From what I've read, I'll need the controller to manage the APs if I want them all to offer the same broadcast domain and subnet, and offer roaming to the users. Often times what I read and understand turns out to have little to do with reality, so my question is, am I correct about this?
Thanks in advance!
Joe

http://www.cisco.com/en/US/docs/wireless/controller/4.2/configuration/guide/c42ovrv.html#wp1133151
These hardware features are not supported on 2000 and 2100 series controllers:
•Power over Ethernet (PoE) [2000 series controllers only]
Note Ports 7 and 8 on 2100 series controllers are PoE ports.
•Service port (separate out-of-band management 10/100-Mbps Ethernet interface)
These software features are not supported on 2000 and 2100 series controllers:
•VPN termination (such as IPSec and L2TP)
•Termination of guest controller tunnels (origination of guest controller tunnels is supported)
•External web authentication web server list
•Layer 2 LWAPP
•Spanning tree
•Port mirroring
•Cranite
•Fortress
•AppleTalk
•QoS per-user bandwidth contracts
•IPv6 pass-through
•Link aggregation (LAG)

I'm trying to submit a document from pages to a URL address and it keeps giving me the option to load pictures or take a new picture, how do I change this?

I'm trying to submit a document from pages to a URL address and it keeps giving me the option to load pictures or take a new picture, how do I change this?

If mean by way of Safari, that is correct. Only content of the Camera or Photos apps are available. you will need to find an alternate app such as iCab Mobile for uploading documents to a website.

Aironet 1250 and AIR-ANT2430V-R

Hello,
I've just installed a Aironet 1250 and AIR-ANT2430V-R antenna.
I could do with some pointers on configuring the 2.4Ghz radio interface.
Role: Access Point
Goal: Blanket office coverage
Channel width: 20Mhz or 40+ ?
External Antenna Configuration: Enable
Gain: ??db
Currently I'm seeing speeds between 1Mbps and 144Mbps, with sporadic coverage.
I was expecting Â£900+ equipment to be better than the Â£10 D-link POE WAP currently installed! =]
Thank you in advance
K

Do you have the rp-tnc connectors fastened tightly?
How are you measuring the bitrate?
Also, have you tried using a tool such as iperf to measure actual throughput and not bitrate?
If you are running 802.11n rates on the 2.4 spectrum and plan to deploy more APs on the network, you will want to stay away from channel bonding.
We do not run 802.11n on the 2.4 side, only the 5Ghz side.

Aironet 1250, and CAll Manager

Hii Experts,,
Dis any one can help me to fine package for aironet 1250 to use it with CiscoWorks LMS 2.5 the device appear as unknown device and I cannot veiw it in Cisco veiw, and if there is a package for call manager 4.2.
Thanks for you supports.

CCM is not supported by the LMS.
Here is the URL for the supported device table for LMS
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.1/device_support/table/lms31sdt.html#Voice

Aironet 1250

I have an interesting problem. I have an aironet 1250. For months my wireless clients has been connecting with no problems. One day there was a power failure, don't remember making any chnages which I should of saved. After, all of my equipment rebooted with no problems. Now I'm seeing my 802.11N clients having connectivity problems. After 10 to 40 mins I believe they get logout, but the client don't get updated to this. The G and the B no problems. Some are Intel chip sets and some are apples base computers.
Anyone seen this?
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname blackhole
aaa new-model
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
clock timezone -0500 -5
clock summer-time -0400 recurring
ip domain name javabeans
ip ssh version 2
dot11 ssid JavaBeans
authentication open
authentication key-management wpa version 2
guest-mode
wpa-psk ascii 7 033E5D060F0EB78723C3E1815142B053225535E52754556204D116C577F784846032369512E0C40553B2301080C5219177A683E16
dot11 ids mfp distributor
dot11 ids mfp detector
dot11 ids mfp generator
power inline negotiation prestandard source
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid JavaBeans
antenna gain 2
speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 basic-6.0 basic-9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
packet retries 128
station-role root
l2-filter bridge-group-acl
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 input-address-list 750
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid JavaBeans
antenna gain 3
dfs band 1 2 3 4 block
speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel width 40-above
channel 5180
station-role root
no dot11 extension aironet
l2-filter bridge-group-acl
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 input-address-list 750
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 10.5.15.1 255.255.0.0
ip helper-address 10.5.20.1
no ip route-cache
ip default-gateway 10.5.1.1
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
logging history size 50
logging history notifications
logging 10.5.20.1
snmp-server community java RO
radius-server attribute 32 include-in-access-req format %h
radius-server vsa send accounting
bridge 1 route ip
line con 0
session-timeout 30
line vty 0 4
session-timeout 30
sntp server 10.5.1.1
sntp broadcast client
end

this is what I got from the AP
2009-04-17 15:59:47 Local7.Info 10.5.15.1 214: Apr 17 19:59:46.885: %DOT11-6-ASSOC: Interface Dot11Radio0, Station blackhole 0013.e871.5b29 Associated KEY_MGMT[WPAv2 PSK]
2009-04-17 15:59:52 Local7.Info 10.5.15.1 215: Apr 17 19:59:51.969: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 0013.e871.5b29 Reason: Sending station has left the BSS
2009-04-17 16:00:55 Local7.Info 10.5.15.1 216: Apr 17 20:00:54.298: %DOT11-6-ASSOC: Interface Dot11Radio0, Station blackhole 0013.e871.5b29 Associated KEY_MGMT[WPAv2 PSK]
2009-04-17 17:04:56 Local7.Warning 10.5.15.1 218: Apr 17 21:04:55.640: %DOT11-4-CCMP_REPLAY: AES-CCMP TSC replay was detected on a packet (TSC 0x102313) received from 0013.e871.5b29.
2009-04-17 17:05:24 Local7.Warning 10.5.15.1 219: Apr 17 21:05:23.570: %DOT11-4-CCMP_REPLAY: AES-CCMP TSC replay was detected on a packet (TSC 0x10C31F) received from 0013.e871.5b29.
it looks like the clients reconnect 30mins later after, what ever happens.

Aironet 1250 Overlapping Channels

Hi,
In my LAN, I have always been used an Aironet 1250 for internal use and always work fine. Now, I added a 3com AP but both AP are not correct. When I turned off the AIRONET 1250, the 3COM AP settings works fine. When both are turn on, the 3COM AP loses connectivity all the time.
I have heard about the overlapping channels in 802.11b/g networks.
Someone could tell me what I could do for solving this?
Note: Due to restrictions on my security lan, I could not use two SSID(using vlans) on my aironet 1250. This will be the best scenario, but it was not possible.
Thanks in Advance,
Fernando

yes. The Aironet 1250 connects to a DHCP server in the range 10.150.x.x and the 3com AP connects to a range 192.168.1.x. The DHCP servers are in different places and there is no any possibility that they could overlap one and another.
But I realized that the problem must be between the two access point because the 3 com AP got an IP Address from the range 10.150.x.x(it sounds crazyness but its true). Offcourse, soon the 3COM AP loses the connection.
Tks you very much,
Fernando

Aironet 1250 in lightweight mode?

Can the Aironet 1250 802.11n WAPs be made to run in lightweight mode like the 1240's can?
Been poking around the cisco site and cant find anything that clearly says yes or no.
thanks
e-

Y'sure can. Here's a link to show you how it's done:
1. The EASY way:
Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode
www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html
2. The CLI way:
Requirements:
â¢ Image file (The recovery file has the prefix ârcvâ in the image name, such as c1200-rcvk9w7-tar.122-15.JA.tar);
â¢ AP is connected to the Wireless LAN Controller; and
â¢ AP can ping the TFTP server where the image is located.
Procedure
1. Copy the recovery file to the AP using the following command:
archive tar /x tftp:/// flash:
2. Let the AP boot on this image:
boot system flash://.bin
3. Reboot the AP.
OPTIONAL
â¢ DO NOT ALLOW THE AP TO JOIN THE WIRELESS LAN CONTROLLER.
â¢ IF POSSIBLE, type the following commands:
ï¾ clear lwapp private-config (This will bring the AP to factory default.);
ï¾ clear lwapp ap ip address
ï¾ clear lwapp ap hostname
ï¾ clear lwapp ap controller ip address
4. Let the AP connect to the Wireless LAN controller.
OPTIONAL
If an AP refuses to join the Wireless LAN Controller, type the following command from the AP:
lwapp ap controller ip address
Hope this helps.

Setting up Cisco Aironet 1250 for home use

Hey everyone,
I'm rather new to the whole Enterprise Router lines. I've set up countless networks with Linksys routers in the past. However, this Aironet is giving me more trouble than I'd want it to. I was wondering if anyone could help. I've assigned it an IP Address and accessed that In-Browser interface and set up an SSID and activated the two extensions. I've been able to connect to the router with my computer and access the internet without restriction. However, when I attempt to connect a second PC or Laptop to the network, it won't allow network access to the second device. I've been stuck there forever. Is there any specific setup method I need to use to make sure more than one workstation/device? I want to use this router for home use, I often use laptops and move around the house a lot, so the advantage of better connection signal and speed is well worth it. Any help is highly apprieciated. If you need more information, don't hesitate to contact me.

Sorry for my late reply. Here is the config:
It wasn't connected to anything. This was a raw pull from a fresh cold boot.
IOS Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 150 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 6406144
flashfs[0]: Bytes available: 25462784
flashfs[0]: flashfs fsck took 16 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: 54:75:d0:dd:b5:12
Loading "flash:/c1250-k9w7-mx.124-10b.JDA3/c1250-k9w7-mx.124-10b.JDA3"...##################################################################################################################################################################################################################
File "flash:/c1250-k9w7-mx.124-10b.JDA3/c1250-k9w7-mx.124-10b.JDA3" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Sun 07-Jun-09 03:50 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x01000000
Initializing flashfs...
flashfs[1]: 150 files, 7 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 31868928
flashfs[1]: Bytes used: 6406144
flashfs[1]: Bytes available: 25462784
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Warning: the compile-time code checksum does not appear to be present.
Radio 1 A600 8000 0 0 A8030000 30
Radio 1 A600 8000 0 0 B8030000 13
tx_paks 1293
tx_paks 646
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html you require further assistance please contact us by sending email to
[email protected]. AIR-AP1252AG-A-K9    (PowerPC 8349) processor (revision C0) with 49142K/16384K bytes of memory.
Processor board ID FTX1423902R
PowerPC 8349 CPU at 533Mhz, revision number 0x0031
Last reset from power-on
1 Gigabit Ethernet interface
2 802.11 Radio(s)
If
cisco
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 54:75:D0:DD:B5:12
Part Number                          : 73-10425-06
PCA Assembly Number                  : 800-27630-06
PCA Revision Number                  : B0
PCB Serial Number                    : FOC142025F4
Top Assembly Part Number             : 800-29039-03
Top Assembly Serial Number           : FTX1423902R
Top Revision Number                  : A0
Product/Model Number                 : AIR-AP1252AG-A-K9
Press RETURN to get started!
*Mar 1 00:00:06.211: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.039: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:07.543: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:09.587: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 00:00:09.591: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Sun 07-Jun-09 03:50 by prod_rel_team
*Mar 1 00:00:09.591: %SNMP-5-COLDSTART: SNMP agent on host Cisco1250 is undergoing a cold start
*Mar 1 01:37:52.027: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 01:37:52.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 01:37:52.707: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 01:37:53.467: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 01:37:53.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 01:37:53.847: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 01:37:54.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 01:37:54.695: %CDP_PD-4-POWER_OK: Full power - INJECTOR_DETECTED inline power source
*Mar 1 01:37:54.703: %DOT11-4-NO_HT: Interface Dot11Radio1, Mcs rates disabled on vlan 0 due to not using AES encryption or
*Mar 1 01:37:58.303: %DOT11-6-FREQ_USED: Interface Dot11Radio1, frequency 5180 selected
*Mar 1 01:37:58.307: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 01:37:58.307: %DOT11-4-NO_HT: Interface Dot11Radio0, Mcs rates disabled on vlan 0 due to not using AES encryption or
*Mar 1 01:37:58.311: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0, Scanning frequencies for 13 seconds
*Mar 1 01:37:59.307: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 01:38:00.307: %LINK-3-UPDOWN: Interface BVI1, changed state to down
*Mar 1 01:38:02.931: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar 1 01:38:11.919: %DOT11-6-FREQ_USED: Interface Dot11Radio0, frequency 2462 selected
*Mar 1 01:38:11.923: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 01:38:12.923: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Cisco1250>enable
Password:
Cisco1250#show running-config
Building configuration...
Current configuration : 1717 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname Cisco1250
enable secret 5 $1$jDeQ$cFdx0aHAd8wj8tk6CCmXq/
no aaa new-model
dot11 ssid Home Network
   authentication open
   guest-mode
power inline negotiation prestandard source
username Cisco password 7 05280F1C2243
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption key 1 size 128bit 7 23D0220D02AE7FA723492AA01E34 transmit-key
encryption mode wep mandatory
ssid Home Network
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption key 1 size 128bit 7 0B4935657C801B3620154AB56630 transmit-key
encryption mode wep mandatory
ssid Home Network
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.0.1 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
snmp-server community Community RW
bridge 1 route ip
line con 0
line vty 0 4
login local
end
They way I connect it in the network is as follows:
BrightHouse Networks ISP Modem --> Cisco Aironet 1252 --> Incoming connections from computers and laptops.
Any ideas?

I recently had to change my email address to a gmail address and my itunes login on my iphone still uses my old email address.

After going tthrough a recent change with my internet provider, I was forced to change my email address. I now use gmail for my mail. With my new gmail address, I went to itunes and updated my account to reflect my new email addess. At the same time, I also just bought a brand new iphone4s and got it all squared away.
Here's my problem; Now that I've changed my itunes account to the new gmail address, whenever I try to buy an app for my phone or access itunes on my phone, the popup window for me to log into itunes shows my I.D. as my old email address. Now I can't log into itunes or buy an app for my phone.
Can somebody please tell me how to fix this??

I had the same problem. I tried everything I could think of, and I was just about to reset my iPad. The last thing I tried was giving in and telling the App store app that I'd forgotten my password. It took me through the password change process (for the old email address), and now it's downloading and updating apps normally.
It's still using my old email address in the iPad store app, but it works, and it syncs with iTunes on my Macbook with no problem.

Error on invoking a webservice by giving ip address instead of local host

Hi,
I created a web service through jdeveloper and tried accessing the webservice generated WSDl file by giving ip address of my machine , but it throws me an error stating IE cannot display the web page . The same web service is running fine when giving local host on the Web service URL .
Looking frwd fr sme help
Thanks in advance
Ragaven

Hi,
your WebLogic server is not setup to listen for the IP address. You can change this in the WLS console for the server configuration. Note that when you install WLS and don't define any hostname then it will listen to all addresses (which also is the default for the integrated WLS)
Frank

During OSD in WINPE the clients loses it's IP Address and fails

Hello,
Since 3 weeks we have an issue where the clients are releasing there IP address during OS Deployment, and mostly during downloading the .wim file or during the applying image. (If you try
for 4 or 5 times it sometime passes and will be successfully deployed)
The DHCP lease times are set to 24H. I ran a F8 and then i did a ping to the distribution server during the download / applying. What we see is that after and X moment (within 20min still
in WinPE) the NIC looses its IP address and gets a 169.x.x.x.x.x address.
If this happens during Applying Images (before its complete) and you manually do a ipconfig/release and /renew it successfully continues. If it happens during download it off course stops
instantly.
We tested it on several routers and different configurations. All with the same result a failing OSD. We ran SCCM2012 SP1. The WinPE has the latest NIC drivers.
Greetings

We almost solved the problem :) Indeed DHCP is the problem. Although the config of both DHCP servers is configured the same with a lease of 24h (deployment vlan) one of the DHCP servers is giving the clients a lease time of 10 minutes. When this lease time
expired the clients arent automatic renewing the lease and Deployment will fail.
DHCP config is renewed and coded with different lease time but still clients get 10min lease.
More on Monday :)

Giving IP address and DCHP to aironet 1250

Similar Messages

Maybe you are looking for