Giving up default gateway in Solaris 10
Good Morning !!!
Hi ..
could you tell me, how can i add default gateway in solaris 10?
i mean , i wanted give up as follows:
rute add default 100.110.120.130
but it does not work !!
Thanks.
Could you post the output from what you're doing? This because beside the typo the following command should work when your root.
route add default 100.110.120.130 Another option is the following command, but then you need to reboot the system afterwards.
echo "100.110.120.130" > /etc/defaultrouter
Similar Messages
-
Setting up IP,Subnet, default gateway and secondary gateway in solaris 10 x
Hi,
I am new to solaris.
I have instralled solaris10 x86 on my system.
I am not able to access internet as i am not able to setup address.
I use broadband and have static ip address.
How do i configure them...
ip, subnet, default gateway, and secondary gateway.
Thanks in advance.run sys-unconfig and after reboot set the parameters (IP, etc)
What do you mean second gateway? -
How to configure default gateway Solaris 9
How to configure default gateway using /etc/gateways file (NO /etc/defaultrouter).
The line "net default gateway ip_router metric 1 passive" produce the following error message:
in.routed: bad net "default" in /etc/gateways entry "net default gateway ip_router metric 1 passive"--cannot be default.
With Solaris 8 is ok.
Can you help me.you've probably worked this out by now, but this may help others;
net 0.0.0.0 gateway x.x.x.x metric 1 passive
* x.x.x.x = your gateway IP -
Changing Default Gateway in Zone
I'm alittle confused and embaroused to even post this. But, is there a restriction on changing the default gateway within a Zone? I get told I don't have insufficient privileges if I do it via "route". I even tried using /etc/defaultrouter, but that had no effect. Am I hitting a restriction that I was unaware of?
Local zones are not allowed to change the network
configuration at all; that includes the interface
configuration (ifconfig) and the routing table
(route).
If your local zone is on the same subnet as the global
zone, they can use the same default route (configured
in the global zone). If they're on different subnets,
you can configure two default routes in the global
zone, and each zone will use the correct gateway.
We have an open RFE to be able to set default routes
in the zone configuration. It's unlikely that it'll
make it into Solaris 10 soon though.
Hope this helps,
BlaiseThis sounds like it's independent of zones. I.e. if I only have the global zone and I have eri0 with 192.168.1.5/24 and qfe0 with 10.1.1.10/24 and then have two default gateways 192.168.1.1 and 10.1.1.1, it will pick the appropriate default gateway based on the src ip address of the outbound packet?
If so, is this a new feature in Solaris 10, or do you know if previous versions also have the same behavior? Unfortunately the current available documentation out on docs.sun.com is not very clear on this (and since Solaris 10 is in beta, that's understandable). I've actually run into a couple of situations where this would be quite useful, so it'd be nice to know if I have to wait for Solaris 10 to be released or if its something that can be done today (I have no place to test this unfortunately) -
Default gateways and zones in a multihomed system
We do have some problems concerning default routes and zones in a multihomed system.
I found several posts in this forum, most of them referring to a domument of meljr, but my feeling ist that the paper is either not correct or not applicable to our situation?! Perhaps somebody can give me a hint.
Let me sketch our test environment. We have a multihomed Solaris 10 system attached to three different DMZ's using three different network adapters. We set up two local zones with IP's of the DMZ's of adapter 1 and 2, leaving adapter 0 for the IP of the global zone.
Now we set up default routes to ensure that network traffic from the local zones is routed in the corresponding DMZ's. That makes three different default routes on the global zone. On startup of the local zones, netstat reports the expected default routes to the correct DMZ gateways inside each zone.
Now what happens... My ssh to the global zone sometimes breaks. When this happens, no pings are possible to the IP of the global zone. Meanwhile, pings from other machines in our network (even from different subnets) might produce replies, some don't. By now, I can't tell you if there's is anything deterministic about it... More interesting: the local zone connections aren't affected at all!
So we did some more testing. Binding an IP address to the DMZ interfaces where the zones are tied to makes no difference (we tried both, with or without dedicated addresses for the adapter in the global zone). So the setup we're using right now is made of 5 IP addresses.
IP1, subnet 1: adapter 0, global zone
IP2, subnet 2: adapter 1, global zone
IP3, subnet 2; adapter 1. local zone 1
IP4, subnet 3; adapter 2, global zone
IP5, subnet 3; adapter 2, local zone 2
In the global zone there are three default gateways defined, one in each DMZ subnet. Inside the local zones, at startup you'll find the corresponding gateway into the DMZ. Everything looks fine...
I opened five ssh connections to the different IP's. Now what happened... After approx. half an hour, the connections to two IPs of the global zone (adapter 0 and adapter 1) broke down, while the connections to all other IP's were still open. This behaviour can be reconstructed!
So perhaps anybody has a explaination for this behaviour. Or perhaps anybody can answer me some qustions:
1. How are the three default gateways handled? Is there still some kind of "round robbin" implemenation? How can I guarantee that network traffic from outside isn't routed inside the DMZ's without preventing the local zones from talking to each other (actually we only need to communicate on some ports, but the single IP-stack concept only gives us all or nothing...).
2. If I do a ping from local zone 1 to the default gateway of local zone 2, this route is added as additional default gateway inside local zone 1! So does this mean, the routing decision is made only inside the global zone not taking into account where the packet is sent from?
3. After all, how are the IP packets routed from the different zone and the global zone, and how are they routed back to calling systems from the various DMS's and other networks, routed via these DMS's???
The scenario seems to be covered by http://meljr.com/~meljr/Solaris10LocalZoneDefaultRoute.html, but configuring the machine like stated in the paper leaves me with the problems described.
I'd be happy for any helpful comment!you can have multiple gateway entries in deafultrouter file but the default gateway for global zone can be only one but you can specify different gateways for different zones..
using this default gateway, you should be able to connect via different network...! -
Default runlevel in Solaris 10
Is it possible to change the default runlevel in Solaris 10 to runlevel 3, so that Solaris 10 boots to and runs in a straight command line? Inittab doesn't seem to control the default runlevel in Solaris 10. Thanks, Kevin.
I don't think this is complete. If you wish to change the default runlevel in which the system starts you'd be using the -d parameter for svcadm so that it will make the specified milestone the default.
However, there are much easier ways.. The service responsible for all of this is svc:/system/svc/restarter, its options/milestone property defines the default milestone and when its absent it defaults to 'all'.
Therefor its probably much easier to simply add a new milestone entry which defines what has to be done. Before SMF the only reason to make a system boot into another runlevel but 3 (say 4) was to make it more easy to start certain services (which were then conveniently put into the right rc.d script). But with SMF you really don't need that anymore; just make a milestone with a corresponding script, make it dependend on the (extra) services you want to start and that's basicly it. The moment your milestone is reached the service(s) are started, and when you disable it stopped. -
The Default Gateway Is Not Available / Problem
Hello, I recently purchased this HP Pavileon laptop, and I've been encountering this problem very often (every 2-10 minutes). This problem is getting extremely frustrating as absolutely nobody has been able to provide a fix for this issue.
When the laptop is on battery mode (this does not happen when plugged in); I commonly get disconnected from my wi-fi connection and to fix it, I must run the troubleshooter. This temporarily fixes the issue by resetting the wi-fi adapter.
What I have tried and has not worked:
* Turn off to save power option in the driver settings (in Device Manager) untickets
* Updated drivers
* New power plan
* Tried different drivers
* Complete system restore
The wireless adapter is Realtek RTL 8188EE. Upon running the troubleshooter, this is all the information from the detailed information section:
Windows Network Diagnostics
Publisher details
Issues foundThe default gateway is not available
The default gateway is not availableThe default gateway is a device that connects a local network or computer to the Internet. A broadband modem or router is usually the default gateway.
Fixed
Reset the "WiFi" adapter
Completed
Investigate router or broadband modem issues
Not run
Issues found
Detection details
6The default gateway is not availableFixed
The default gateway is a device that connects a local network or computer to the Internet. A broadband modem or router is usually the default gateway.
Reset the "WiFi" adapterCompleted
This can sometimes resolve an intermittent problem.
Network Diagnostics LogFile Name: 2D0FE1F0-C2C2-43B5-A857-2D2B3C4B8A51.Repair.1.etl Investigate router or broadband modem issuesNot run
If you're connected to a hotspot or domain network, contact the network administrator. Otherwise: 1. Unplug or turn off the device. 2. Once all the lights on the device are off, wait at least 10 seconds. 3. Turn the device on or plug it back in to the power outlet. To restart a router or modem that has a built-in battery, press and quickly release the Reset button.
Detection details
Diagnostics Information (Network Adapter)
Details about network adapter diagnosis:
Network adapter WiFi driver information:
Description . . . . . . . . . . : Realtek RTL8188EE 802.11b/g/n Wi-Fi Adapter
Manufacturer . . . . . . . . . : Realtek Semiconductor Corp.
Provider . . . . . . . . . . . : Realtek Semiconductor Corp.
Version . . . . . . . . . . . : 2012.2.827.2013
Inf File Name . . . . . . . . . : C:\WINDOWS\INF\oem8.inf
Inf File Date . . . . . . . . . : 12 September 2013 10:17:00
Section Name . . . . . . . . . : HP8188ee.ndi
Hardware ID . . . . . . . . . . : pci\ven_10ec&dev_8179&subsys_197d103c
Instance Status Flags . . . . . : 0x180200a
Device Manager Status Code . . : 0
IfType . . . . . . . . . . . . : 71
Physical Media Type . . . . . . : 9
Diagnostics Information (Wireless Connectivity)
Details about wireless connectivity diagnosis:
Information for connection being diagnosed
Interface GUID: 7c04789b-0b43-472c-abd6-a84cb31e9053
Interface name: Realtek RTL8188EE 802.11b/g/n Wi-Fi Adapter
Interface type: Native WiFi
Connection incident diagnosed
Auto Configuration ID: 1
Connection ID: 1
Connection status summary
Connection started at: 2014-07-24 04:19:49-759
Profile match: Success
Pre-Association: Success
Association: Success
Security and Authentication: Success
List of visible access point(s): 0 item(s) total, 0 item(s) displayed
Connection History
Information for Auto Configuration ID 1
List of visible networks: 1 item(s) total, 1 item(s) displayed
BSS Type PHY Security Signal(RSSI) Compatible SSID
Infra <unknown> Yes 100 Yes Matt
List of preferred networks: 1 item(s)
Profile: Matt
SSID: Matt
SSID length: 4
Connection mode: Infra
Security: Yes
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: Yes
Information for Connection ID 1
Connection started at: 2014-07-24 04:19:49-759
Auto Configuration ID: 1
Profile: Matt
SSID: Matt
SSID length: 4
Connection mode: Infra
Security: Yes
Pre-Association and Association
Connectivity settings provided by hardware manufacturer (IHV): No
Security settings provided by hardware manufacturer (IHV): No
Profile matches network requirements: Success
Pre-association status: Success
Association status: Success
Last AP: 98-fc-11-88-61-b8
Security and Authentication
Configured security type: WPA2-PSK
Configured encryption type: CCMP(AES)
802.1X protocol: No
Key exchange initiated: Yes
Unicast key received: Yes
Multicast key received: Yes
Number of security packets received: 0
Number of security packets sent: 0
Security attempt status: Success
Connectivity
Packet statistics
Ndis Rx: 34302
Ndis Tx: 32619
Unicast decrypt success: 0
Multicast decrypt success: 0
Unicast decrypt failure: 0
Multicast decrypt failure: 0
Rx success: 0
Rx failure: 0
Tx success: 0
Tx failure: 0
Tx retry: 0
Tx multiple retry: 0
Tx max lifetime exceeded: 0
Tx ACK failure: 0
Roaming history: 0 item(s)
Diagnostics Information (Wireless Connectivity)
Details about wireless connectivity diagnosis:
For complete information about this session see the wireless connectivity information event.
Helper Class: Auto Configuration
Initialise status: Success
Information for connection being diagnosed
Interface GUID: 7c04789b-0b43-472c-abd6-a84cb31e9053
Interface name: Realtek RTL8188EE 802.11b/g/n Wi-Fi Adapter
Interface type: Native WiFi
Result of diagnosis: There may be problem
Diagnostics Information (Wireless Network Adapter)
Details about wireless network adapter diagnosis:
For complete information about this session see the wireless connectivity information event.
Helper Class: Native WiFi MSM
Initialise status: Success
Information for connection being diagnosed
Interface GUID: 7c04789b-0b43-472c-abd6-a84cb31e9053
Interface name: Realtek RTL8188EE 802.11b/g/n Wi-Fi Adapter
Interface type: Native WiFi
Profile: Matt
SSID: Matt
SSID length: 4
Connection mode: Infra
Security: Yes
Connect even if network is not broadcasting: No
Result of diagnosis: There may be problem
Network Diagnostics LogFile Name: 2D0FE1F0-C2C2-43B5-A857-2D2B3C4B8A51.Diagnose.0.etl
Other Networking Configuration and LogsFile Name: NetworkConfiguration.cab Collection information Computer Name: LAPTOP Windows Version:6.3Architecture:x64Time:24 July 2014 04:34:47
Windows Network Diagnostics Detects problems with network connectivity. Package Version:1.0Publisher:Microsoft WindowsRun the HP Support Asssitant's Tune up application. There should be a new BIOS available. sp66866
Have you installed the latest Windows 8.1 updates?
Do not install optional video graphics updates.
I was runnning into a similar problem with my HP product loan Envy Spectre 13 TouchSmart Ultrabook until I did the updates. I had upgraded my wireless router to a model with 802.11AC specification.
Invoke the Device Manager and ensure that the box next to Allow this computer to turn off this device to save power is unchecked.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer -
Error giving a default value to a date column in the attribute settings.
When im giving a default value to a date column in the attribute settings i get this error when im running my jsp page (bc4j web application):
Error Message: JBO-25009: Cannot create an object of type:oracle.jbo.domain.Date with value: 31-dic-2099
How can i fix that?
Thank uThe default date format for oracle.sql.DATE which oracle.jbo.domain.Date extends is "YYYY-MM-DD"
-
Hello!
I want to create bat script to create several VPN connection.
There is powershell command to create vpn connection:
add-vpnconnection -name "Test VPN" -serveraddress "vpn.example.com" -splittunneling -tunneltype "pptp"
And I need to create VPN connection without the option "Use default gateway on remote network" option on VPN connection"
Or modify this option on existent VPN connection with command.
Please help me to find command option or other command to disable "Use default gateway on remote network" option on VPN connection" feature.http://technet.microsoft.com/nl-nl/library/ee431701%28v=ws.10%29.aspx RouteIPv4TrafficOverRAS True – Add a default gateway on the VPN connection False – Do not add default gateway on the VPN connection
-
How to setup default gateway in a DHCP client. The default gateway will be the Ip address of the server that has RRAS installed, hence routing cabalities.
Hi Bill,
Thank you for replying back...Yes, I was actually asking how do you set the default gateway address on the DHCP server?,
I believe I got the answer below:
To configure the DHCP default gateway option Click Start, point to Administrative Tools and then click DHCP. In the console tree, expand the applicable DHCP server, expand IPv4, and then right-click Scope Options Click Configure Options, check 003
Router, type the applicable Server name and IP address, and then click OK.
Thank you -
Loss of default gateway - to auto-shutdown radio
Hi,
I need a solution where, if an access point looses its connection to its default gateway, that it automatically shuts the radio down. And when the default gateway is again available, the radio is automatically turned on again. By connection, I do not just mean that the AP FastEthernet port link status changes.
Some kind of functionality like the 'track rtr reachability' that probes the default gateway, and takes action if the default gateway cannot be reached.
How to, if at all possible...
Problem is that wireless equipment will connect to the access point if the radio is up but the access point does not have access to its default gateway (for some error reason other than the local Ethernet link, but also that...)
Thanks
JohnnyHi,
unfortunately that does not solve this problem:
Router (def. gw for WAP)
Switch 1
Switch 2
Wireless Access Point (WAP)
If switch 1 is down or if the link from switch 1 to the router is down, then the WAP radio will still be up. I need for it to handle a loss to its default gateway, not just its local ethernet wire.
Tx
Johnny -
Changing Router IP while keeping default Gateway
Hello- I have a Linksys WRT150N Wireless Router. The default (out of the box) IP Address is 192.168.1.1, which is also the default Gateway. I would like to know if it is possible to change the IP address to 192.168.1.2 while keeping the Gateway on 192.168.1.1. The problem I run into is that when I do change the IP to 192.168.1.2, the Gateway also changes to that address. I see it is possible under Automatic Configuration - DHCP to change the IP and the Subnet Mask, but not the Gateway. Any ideas? Thank you
Message Edited by thutter on 05-20-2008 05:36 AMNo it won't be possible for you to do the settings i.e., to change the ip address to 192.168.1.2...better keep in the same & do the settings.
-
Default Gateway when connected to VPN
Thanks for reading!
This is probably a dump question so bear with me...
I have set up a VPN connection with a Cisco ASA 5505 fronting internet, with the customers environment behind it (on the same subnet), When connected ot the VPN I can reach the inside Router fronting me and one switch behind the Router (every switch is connected to the router), but nothing else.
My beet is that the Router is messing with my connection, but,, nevermind that!, the setup ain't complete anyway... my question is more related to the Gateway I'm missing when I'm, from the outside, is connected to the VPN on the ASA, could this mess it up? Shouldn't I have a Standard-Gateway in the ipconfig settings in windows?
This is who it looks like now:
Anslutningsspecifika DNS-suffix . : VPNOFFICE
IP-adress . . . . . . . . . . . . : 10.10.10.1
Nätmask . . . . . . . . . . . . . : 255.255.255.0
Standard-gateway . . . . . . . . :
The internal network is :
172.16.12.0 255.255.255.0
Below is my config for the ASA, thanks a lot!!!!!!!
!FlASH PÅ ROUTERN FRÅN BÖRJAN
!asa841-k8.bin
hostname DRAKENSBERG
domain-name default.domain.invalid
enable password XXXXXXX
names
interface Vlan1
nameif inside
security-level 100
ip address 172.16.12.4 255.255.255.0
interface Vlan10
nameif outside
security-level 0
ip address 97.XX.XX.20 255.255.255.248
interface Ethernet0/0
switchport access vlan 10
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
clock timezone CEST 1
clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00
dns server-group DefaultDNS
domain-name default.domain.invalid
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
access-list nonat extended permit ip 172.16.12.0 255.255.255.0 10.10.10.0 255.255.255.0
access-list MSS_EXCEEDED_ACL extended permit tcp any any
access-list VPN-SPLIT-TUNNEL remark VPN SPLIT TUNNEL
access-list VPN-SPLIT-TUNNEL standard permit 172.16.12.0 255.255.255.0
tcp-map MSS-MAP
exceed-mss allow
pager lines 24
logging enable
logging timestamp
logging buffer-size 8192
logging console notifications
logging buffered notifications
logging asdm notifications
mtu inside 1500
mtu outside 1500
ip local pool VPN 10.10.10.1-10.10.10.40 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any outside
asdm image disk0:/asdm-625-53.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list nonat
nat (inside) 1 172.16.12.0 255.255.255.0
route outside 0.0.0.0 0.0.0.0 97.XX.XX.17 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 172.16.12.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 172.16.12.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
group-policy VPNOFFICE internal
group-policy VPNOFFICE attributes
dns-server value 215.122.145.18
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value VPN-SPLIT-TUNNEL
default-domain value VPNOFFICE
split-dns value 215.122.145.18
msie-proxy method no-proxy
username admin password XXXXXX privilege 15
username Daniel password XXXXX privilege 0
username Daniel attributes
vpn-group-policy VPNOFFICE
tunnel-group VPNOFFICE type remote-access
tunnel-group VPNOFFICE general-attributes
address-pool VPN
default-group-policy VPNOFFICE
tunnel-group VPNOFFICE ipsec-attributes
pre-shared-key XXXXXXXXXX
class-map MSS_EXCEEDED_MAP
match access-list MSS_EXCEEDED_ACL
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect icmp error
inspect pptp
inspect ipsec-pass-thru
inspect icmp
class MSS_EXCEEDED_MAP
set connection advanced-options MSS-MAP
service-policy global_policy global
privilege cmd level 3 mode exec command perfmon
privilege cmd level 3 mode exec command ping
privilege cmd level 3 mode exec command who
privilege cmd level 3 mode exec command logging
privilege cmd level 3 mode exec command failover
privilege cmd level 3 mode exec command packet-tracer
privilege show level 5 mode exec command import
privilege show level 5 mode exec command running-config
privilege show level 3 mode exec command reload
privilege show level 3 mode exec command mode
privilege show level 3 mode exec command firewall
privilege show level 3 mode exec command asp
privilege show level 3 mode exec command cpu
privilege show level 3 mode exec command interface
privilege show level 3 mode exec command clock
privilege show level 3 mode exec command dns-hosts
privilege show level 3 mode exec command access-list
privilege show level 3 mode exec command logging
privilege show level 3 mode exec command vlan
privilege show level 3 mode exec command ip
privilege show level 3 mode exec command ipv6
privilege show level 3 mode exec command failover
privilege show level 3 mode exec command asdm
privilege show level 3 mode exec command arp
privilege show level 3 mode exec command route
privilege show level 3 mode exec command ospf
privilege show level 3 mode exec command aaa-server
privilege show level 3 mode exec command aaa
privilege show level 3 mode exec command eigrp
privilege show level 3 mode exec command crypto
privilege show level 3 mode exec command vpn-sessiondb
privilege show level 3 mode exec command ssh
privilege show level 3 mode exec command dhcpd
privilege show level 3 mode exec command vpnclient
privilege show level 3 mode exec command vpn
privilege show level 3 mode exec command blocks
privilege show level 3 mode exec command wccp
privilege show level 3 mode exec command webvpn
privilege show level 3 mode exec command module
privilege show level 3 mode exec command uauth
privilege show level 3 mode exec command compression
privilege show level 3 mode configure command interface
privilege show level 3 mode configure command clock
privilege show level 3 mode configure command access-list
privilege show level 3 mode configure command logging
privilege show level 3 mode configure command ip
privilege show level 3 mode configure command failover
privilege show level 5 mode configure command asdm
privilege show level 3 mode configure command arp
privilege show level 3 mode configure command route
privilege show level 3 mode configure command aaa-server
privilege show level 3 mode configure command aaa
privilege show level 3 mode configure command crypto
privilege show level 3 mode configure command ssh
privilege show level 3 mode configure command dhcpd
privilege show level 5 mode configure command privilege
privilege clear level 3 mode exec command dns-hosts
privilege clear level 3 mode exec command logging
privilege clear level 3 mode exec command arp
privilege clear level 3 mode exec command aaa-server
privilege clear level 3 mode exec command crypto
privilege cmd level 3 mode configure command failover
privilege clear level 3 mode configure command logging
privilege clear level 3 mode configure command arp
privilege clear level 3 mode configure command crypto
privilege clear level 3 mode configure command aaa-server
prompt hostname context
Cryptochecksum:aaa1f198bf3fbf223719e7920273dc2e
: endI didn't realise I had that crypto settings on, thanks my bad!!!
But... the 172.16.12.0 network is directly connected, the Router (that to be honest is a firewall) / switches is all on the same subnet (172.16.12.X/24), so sorry I didn't explain thoroughly, was more wondering about the GW and didn't want to overcomplicate things..
The Firewall/Router dosen't do any routing, so it should work right (I you count out the firewalling in the firewall and so forth, there shouldn't be any problems accomplishing this with the ASA)? The Firewall is more a DHCP for the clients/Firwall for the clients.. this will change in the future.. it will be removed,
the vpn network is staticly routed back to my ASA in that firewall...
I don't like this solution.. but this is who it looks.. for now..
(VPN network is 10.10.10.X/24)
But... shouldn't I see a default gateway under ipconfig when I'm connected to the VPN from internet, on the vpn client that's vpned in, is this correct?
THANKS for all the help! -
Changing default gateway on sbs08
Hello,
I need to change the default gateway on my small business server 2008 from 192.168.1.207 to 192.168.1.208. The server is used for exchange 2007 and pretty much runs our network.
My manager said this is a big job and I need to read up on DNS, MX records and changing SMTP server IP addresses but I cant see what else I would
need to do.
Any help is greatly appreciated!
Thanks!Hi Nuh,
If you are just looking to change just the gateway IP address, then FOVIA is correct. Just run the Connect to Internet Wizard. For all intensive purposes, your gateway is your firewall or router. Ex. below.
IP Address: 192.168.1.2 <-This is IP address for the server
Subnet: 255.255.255.0
Default Gateway: 192.168.1.207 <- This is the IP address for your gateway, the one that you need to change.
Now, if you manager is asking you to change physically change the gateway(firewall/router) and reconfigfure it and the network, then this "big job" does make sense when dealing DNS, MX records and such. If not, then just run the wizard and you should be
gold. -
Use of default gateway on switch
hi,
there is option to specify default gateway on switch.
what is the purpose of it?
Regards
skraoHi,
Layer 2 switches have to be configured like IP hosts, which are not capable of routing. In the same manner that you assign default gateways to hosts, you need to assign a default gateway to such a L2 switch so that management traffic from the switch can be routed to the gateway router.
Pls do remember to rate posts.
Paresh
Maybe you are looking for
-
Dynamic Positioning of Objects in a Grid (rows and columns) AS3 Tutorial
The topic of a dynamic positioning of objects in a right grid (rows and columns) comes up often so I decided to post an AS3 solution here: http://flashascript.wordpress.com/2010/12/25/arranging-objects-into-2d-dynamic-grid-with-a ctionscript-3/
-
HT2523 how do you change the format to plain in textedit for macmini os x 10.6.8
i dont know how to change my textedit format to plain i have looked it up on multiple websites and i still cant find out how to do it
-
Nokia n85 not playing MP4 files
Hi, I never used the video podcasts, well I just tried to use some nokia video podcasts and they were in MP4 format. To my surprise my phone says it can not play the format and so it just played it as the audio file. I was reading at GSMArena.com and
-
HT4519 iPad says server rejected email receive not and placed in outbox How do I stop this
iPad says server rejected email recipient and placed mail i outbox how do I stop this
-
Has anyone tried the BlueConnect service installed in Hyundai vehicles
I have a 2008 Tucson from Hyundai with a factory installed BlueConnect system. I want to buy a 3g and wondering if people are having the same difficulty as the UConnect systems? Im currently using a Windows Mobile phone that works fine and I use it a