GLC-SX-MM auto detecting as half duplex

I have a 3945 router with a GLC-SX-MM connected to a Canoga 9145 with a 5 meter patch cable going to AT&T as a 100Mb Metro-E
Our performance is poor measuring about 4Mb up and 15Mb down. I have tried various test sites.
A show interface is showing: Half Duplex, 1Gbps, media type is SX
We are seeing a lot of output errors and TCP reassembly queue overflows
If I force the interface to full duplex I stop getting output errors and queue overflows but start getting interface resets. My performance also goes sub 1Mb
The ISP confirms their interface on the Canoga is properly configured. We have also replaced the patch cable.
Does anyone have any thoughts on possible causes?
Gary
http://bytesolutions.com

You're using a 1 Gbps interface and your SP is provisioning a 100 Mbps circuit? That doesn't make sense. Depending on your equipment, you should be using something like the GLC-FE-100FX=, a 100 Mbps SFP. (See http://www.cisco.com/en/US/customer/products/hw/modules/ps5455/products_device_support_tables_list.html )
Otherwise where is the buffering and queuing take place - in the Canoga? From its application guide, I believe it is intended to be used with the fiber on the provider side and the subscriber side is copper. Your post seems to describe the reverse setup.

Similar Messages

Unable to use Auto setting or 100BaseTx in either full or half duplex!

Hi here is the issue, I have a small home network of three desktops, one laptop (wireless) and two game consoles with a WRTP54G router and cable modem. I have noticed that if I try to change the NIC setting on any device to either Auto or 100BaseTx in either full or half duplex the connection drops. The pc will say network unplugged, the minute I change it back to10BaseT in either full or half duplex it comes right back up! Before anyone asks yes my NIC's are 100BaseTx compatable. I have made sure all drivers are up to date. Has anyone had this issue? I would like to use 100Base Tx in Full Duplex! Any help would be appreciated!

hi. the auto sense feature of the router is not working anymore. i dont know if a firmware upgrade will help, but you can give it a shot.

Half Duplex/100M problem on 2960 switch with GLC-GE-100FX

We have a 2960-24TC switch with GLC-GE-100FX SFP interface converter. We connected the switch to another switch through fiber, one end was GLC-GE-100FX and the other end was a 100/FULL ATI media converter. Both switches could talk to each other. The problem was the GLC-GE-100FX interface running at 100M/half duplex status and we couldn't change the port configuration. Is there a way to fix this problem? Your help would be much appreciated.

Using show interface command. It shows half duplex. It's a new design on Cisco 2960-24TC switches, the Giga uplink ports are dual purposed. When I plugged GLC-GE-100FX SFP interface converter and connected it to a media converter, it showed half duplex. There's no way I could change the speed and duplex under that configuration.

NIC only works at 10 Mbps/Half Duplex

Ever since I got this MOBO (almost 1 year ago), I have not been able to connect faster than 10 Mbps/Half Duplex with my ADSL modem. Any attempt to change speed will result in Windows indicating tha the cable is unpluged (Auto mode does not work either). I've updated BIOS, NIC drivers, I've installed WinXP (and re-installed) with and without SP1 and SP2. I've also changed cables with no luck.
I got an external NIC from a friend and could connect at 100 Mbps/Full Duplex so the problem is NOT on the modem side.
System info shows the internal NIC shares IRQ 18 with a USB controller wich I uninstalled just to see if it would make a difference. Same results.
I've just installed the latest drivers from INTEL and I'm still getting the same problem.
Any ideas?
Help will be greatly appreciated.
Abraham

Don't know how to fix this but I had the same problem when I was connected directly to my cable modem. I eventually got it to run manually at 10Mbs-full duplex and didn't worry about it further since that's faster than actual transfer speeds from my ISP anyway.
I then configured a wireless network using a Linksys router and noticed that my NIC now automatically connects at 100Mbs-full dupex as it should.
If you feel this limiting your actual transfer speeds(it wasn't in my case) you might consider purchasing an inexpensive router. This will also give you the benefit of having a hardware firewall.

Solaris 8 on a Sun Fire v480 (full vs half duplex)

Hi All
I've installled Solaris 8 on a Sun Fire v480.
Now, when I boot I get the following (via serial A/LOM):
{2} ok boot -r
Boot device: /pci@9,600000/SUNW,qlc@2/fp@0,0/disk@w2100002037cfdf9d,0:a File and args: -r
SunOS Release 5.8 Version Generic_108528-13 64-bit
Copyright 1983-2001 Sun Microsystems, Inc. All rights reserved.
configuring IPv4 interfaces: ce0.
Hostname: abcdef
WARNING: ce0: fault detected external to device; service degraded
WARNING: ce0: xcvr addr:0x01 - link down
Configuring /dev and /devices
NOTICE: ce0: fault cleared external to device; service available
NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
Configuring the /dev directory (compatibility devices)
The system is coming up. Please wait.
checking ufs filesystems
/dev/rdsk/c1t0d0s5: is clean.
/dev/rdsk/c1t0d0s7: is clean.
starting rpc services: rpcbind done.
Setting netmask of ce0 to 255.255.224.0
Setting default IPv4 interface for multicast: add net 224.0/4: gateway abcdef
syslog service starting.
Print services started.
volume management starting.
The system is ready.
abcdef console login:Dec 22 11:01:34 abcdef picld[70]: Device PS1 AC UNAVAILABLE
Dec 22 11:01:35 abcdef picld[70]: FSP_GEN_FAULT_LED has turned ON: 1 failed device(s)
abcdef console login:
My question is what is going on. I see 2 things:
1)
NOTICE: ce0: fault cleared external to device; service available
NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
what does the first line means and why half duplex and not full
2) FSP_GEN_FAULT_LED has turned ON......
hmmm, what does this mean ?
Any suggestions to help me untangle those messages ?
Thanks a lot in advance
Luca

Hi,How to set my link up in solaris 10 ?
I dont know want happend to my machine solaris v440 it suddenly disconnected from n/w and finally i came to know that is a problem with NIC card..i din't find any light's glowing back side of the machine at NIC card.
can any one help me in this pls how can i proceed furture for getting my NIC back?
and i have excuted few commands
#ndd -set /dev/ce instance 0
#ndd -set /dev/ce adv_1000fdx_cap 1
#ndd -set /dev/ce adv_autoneg_cap 0
I have got dladm show-dev is
ce0 link: unknown speed: 1000 Mbps duplex: full
ce1 link: unknown speed: 0 Mbps duplex: unknown
I dont understand that why my link is showing still unknown ...any help..

CSCus23563 - Jabber unable to auto-detect proxy in IE10 and IE11

Please note that the workaround to use an earlier version of IE is not an option for Windows 8.

hi
yes here we are using auto detect proxy setting bcz for quich change of network . like a user is working in my office and in second half he will be on a client side . so he will just connect his device without any IP configuration . and also there is no need to remember IP settings.
so pls help me to resolve to this issue .

Using GLC-T in FEX 2232PP - Speed and Duplex

First time using GLC-T's in a FEX 2232PP off of 5548 running 5.0(3)N1(1b). Was getting "sfpInvalid" on show int status. Nice engineer explained I had to remove the GLC-T's, configure the interface E101/1/1 to speed 1000 in order for the 5548/FEX to recognize the GLC-T.
That worked, but also led to the recommendation that I hard-code the server NICs to 1000/full rather than auto/auto - their present NIC setting. Not opposed to doing that, except that I am transitioning servers from a temporary 3560G in that same rack to FEX. Since they're all auto/auto (the 3560G ports are as well), I will need change management to reconfigure NICs on each.
I'm an advocate of making sure NIC and switch port match exactly, but have used AUTO/AUTO on switch and server NIC in recent years w/out problems.
Anyone know if there's a way to have GLC-T's recognized by the FEX 2233PP, but still have AUTO/AUTO?
It will help me w/my migration.

Just to clarify Carlo, you're saying that I use speed 1000 on the FEX port configuration, so that it recognizes the GLC-T? And I can leave duplex (or set it) to auto on the FEX, and then the server NIC settings can stay at AUTO/AUTO?
Yesterday, I did add the speed 1000 command to the FEX ports, left the FEX port duplex to whatever the default is, and configured a laptop w/a 1 Gig NIC to be AUTO/AUTO. Connected and did a large FTP (2Gig). It transfered very fast - comparable to baseline - and there were no errors on the FEX port counters.
So, I was thinking it would be ok to leave the servers at AUTO/AUTO, even though the FEX port speed was 1000.

Auto detect proxy setting

in my organization , we are using auto detect proxy setting and my All browser are able to access internet
through auto proxy but Mozilla is not working with auto detect proxy settings ,unable to access internet .
kindly suggest for the same issue ASAP.

hi
yes here we are using auto detect proxy setting bcz for quich change of network . like a user is working in my office and in second half he will be on a client side . so he will just connect his device without any IP configuration . and also there is no need to remember IP settings.
so pls help me to resolve to this issue .

Loopback in Half Duplex

?Half-duplex Ethernet uses a loopback circuit to detect collisions? Is this mean I need to configure a loopback interface to make collision detection work? If yes, where to set that loopback interface? On the switch? Or host? Actually, I normally don?t need to create loopback interface when I plug my computer with hub. How this works? I just don?t understand that statement.
1.12

You do not need to create any loopback interface. The book you are reading is explaining the technology in how a switch detects that there is a collision. This is a hardware mechanism in switches and we do not have to configure anything for this

FaceTime audio half duplex / doesn't work simultaneously

I gave my parents a new iPad Air for Christmas. Note: They are 'older' and have a lot of trouble operating electronic devices. Before sending it to them I did check for recent updates, set up their email and contacts, installed some apps that I find useful and uploaded some photos. Otherwise it's a fresh unit right out of the box.
Yesterday we tried facetime with them. The video worked as it should. The audio seemed to be in a 'half duplex' mode on our device. Meaning, they could hear us perfectly and normally on the iPad. We could only hear them when we were perfectly quiet. Any sounds or talking on our end would mute their transmission during and about 1 second after speaking.
We tried multiple calls. (I called them and then they called me). We tried an iphone 5 and a MacBook, the problem was consistant in all cases. During one of our calls on the mac, my brother placed a facetime call to my phone and his connection worked perfectly, while my parent's connection continued to have the issue.
I sent them the following instructions, in hopes that it may fix the issue, but I'm doubtful. I don't have an iPad handy (only iphones and the mac in our house) so there may be some settings that are present on the iPad and not on the iphone that they should try. Any and all help would be appreciated! They live on Kauai, HI so if there are any places there that would be helpful that they could visit, I would appreciate the recommendation.
Go into settings, scroll down until you see facetime. Select it. There will be some settings for facetime. One simply says facetime and there is a small green slider button next to it. Touch the button. It should slide and turn white. This disables facetime.
Go to settings, then general, then software update. It should say "checking updates" and then will either display your version (7.0.4 ?) OR it will say there is a new update and you can download it. If so, download/install. (Should be a button asking and just hit yes or ok).
Next, do a network reset:
Go to settings, general, scroll down to "reset". Select reset and then select "reset network settings". It will ask if you want to do this and yes, you want to do it.
Next, After all this is done, reboot the ipad. This is done by pressing and holding the top (power/sleep) button and the home button down at the same time. Hold it for 30-seconds maybe longer until the screen goes black and then the apple logo appears. Then let go.
(If you hold just the upper button for 5 seconds a red slider will appear to allow you to turn off the ipad. For a reset just ignore that and keep holding down the buttons).
Once it reboots, add yourself back to your network. It may ask on its own, but if not :
Go to settings, then wi-fi. Select your network and enter your password.
Last, go into settings, general, facetime and turn it back on by touching the white slider button. It should turn green.
I found two other cases that sounded like mine:
https://discussions.apple.com/message/22808569#22808569
https://discussions.apple.com/message/22705969?searchText=Facetime%20duplex#2270 5969

My parents called apple tech support. I'm not exactly sure what they did, but I think they just rebooted the iPad again, as done previously. It seems to be working better now, although it does still cut out now and then from sounds on my end of the line.
Another thing that seems to have helped, I determined that my parents had left it in the original plastic packaging and then crammed it into the case I gave them, which may have slightly muffled their microphones.
Anyway between these two things it is working better. We can speak on this end and still hear them talking. But now and then it still cuts out.

Mac wont mount disk images, and fails to auto detect some usb devices.

for some reason, all of a sudden, my mac won't mount disks. even disks I know in the past have worked.
also, it wont auto detect some external devices. especially jump drives and hard drives and audio interfaces. It has to be rebooted with the the devices connected.
I know its not a hardware problem, because everything runs smooth in windows on this computer.
I did some extensive cleaning recently, and installed a lot of new stuff, but i don't know what could be causing this.
any help would be greatly apreciated!

This USB faq may help.
An SMC reset may help you mount disks.
 DALE

Upon startup Firefox says "Proxy is refusing connections." When I select "Auto-Detect Proxy" from Advanced settings and solve problem, changes are not saved and upon next startup I must select again...!

Firefox 4 was working fine. Then one day, when I started up Firefox, it says "Proxy is refusing connections." I solved this by selecting "Auto-Detect Proxy" from Advanced network settings, but my changes are not saved and upon every start-up I must select it again! (I even completely removed my webroot antivirus protection, as it as hindering many proxy related programs, but this seems to not be the source of the problem)

You can find the connection settings in Tools > Options > Advanced : Network : Connection
If you do not need to use a proxy to connect to internet then select "No Proxy"
See "Firefox connection settings":
* https://support.mozilla.com/kb/Firefox+cannot+load+websites+but+other+programs+can
Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
*Don't make any changes on the Safe mode start window.
*https://support.mozilla.com/kb/Safe+Mode
*https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes
See also:
*http://kb.mozillazine.org/Preferences_not_saved

IMac always auto detects for external monitors after waking from sleep or from display off

I've got a Dell 24" monitor (2408WFP) plugged into my mid 2011 iMac via DVI cord and thunderbolt attachment. Things work fine.
When I need to leave my computer, I usually turn the displays off using the shortcut keys: CTRL + SHIFT + EJECT
This works perfectly and both displays go black. However, when I return to my computer and reactivate the iMac, the iMac display will turn blue as if I have just plugged in a new monitor even the external monitor is still plugged in. It usually flashes blue twice before displaying the password prompt. I can usually just log back in as normal. I've never had this happen before using Snow Leopard. It's annoying but strange.
However, even more strange is that sometimes when returning to the desktop, the iMac will do the auto detect display thing and then when I log back in, the external display just shows static as if there is no signal. I've checked the cable a million times and everything is as tight as tight can be and both ends are plugged in properly. Unplugging the displayport adapter from the iMac and then reattaching it restores the desktop on the secondary display although sometimes, it results in the secondary display showing a gray background picture instead of my normal picture. Replugging the secondary display seems to fix that too although sometimes it doesn't.
Why is this happening?
- Problem with the adapter?
- Problem with the DVI cable I'm using?
- Compatibility issues with my external monitor?
I need to stress the point that this has never happened before with Snow Leopard.
If I am the only one experiencing this then I suppose it may be an issue with the iMac or adapter or even the cable. But if anyone else can shed light on this problem, I'd really appreciate it.

Hi Micheal,
I've been experiencing the exact same issue with my new iMac I just bought. I bought it refurb so I wasn't sure if it was a defect with the hardware or not. Since I'm not the only one I will asume it's not for now.
Setup:
- iMac 27-inch 3.4GHz (Release May 2011)
- Dell 2709W external monitor
- Hooked in with mini display port to DVI adapter
- Lion 10.7.3 all up to date to this day
From what I've been able to gather the issue presents itself only when my Dell 2709W enters "Power Save Mode" after I do CTRL + SHIFT + EJECT or when the diplays simply goes to sleep by themselves.
Although if I hit that combination and the displays goes to sleep but I don't wait long enough for my Dell monitor to actually "Power Save Mode" (wait like 2 sec) then touch the keyboard then the 2 displays (iMac and Dell) resumes from sleep without the issue presenting itself.
I'm tempted to buy the mini-display port to HDMI just to see if the issue is still present with that adapter. If I do I'll update my post with the outcome.
If anyone else has any info to help with this issue it would be greatly appreciated. It's very annoying when you resume from sleep and you find all of your windows that where opened on the external display before sleep squeezed into your main display (iMac).
Thanks!

MFEFX1 not auto-detected on SLM224P-G5

I have been fighting with a pair of Linksys switches, on and off over the past days. What I want to do is very simple, uplink two swtiches via a Fiber connection.
I have been supplied with equipment, which on paper is compatible, but in reality seems incompatible.
I have:
- 2 x MFEFX1
- 1 x SLM224P-G5
- 1 x SRW224G4
- (also a SRW224P - aparently after some digging listed as incompatible with the MFEFX1)
I have upgrade the firmware on the SRW224G4 to 1.2.2b to support the MFEFX1.
I have Firmware 1.0.1 on the SLM224P, listed as auto-detecting the MFEFX1.
According to the (now seemingly unavalable) document: "Linksys100M-SFP-SwitchSupport-noteV1.3.pdf" all the above should now be supported.
I have updated the port configuration on the SRW224G4, and this shows "100M-ComboF" and seems to be OK.
On the SLM224P, however, I see the port as a "1000M-ComboF" and the link stays down.
I see a led light-up on the SRW224G4 for the connection, but nothing else.
At this point I wish that I was supplied with the Gigabit Fiber modules that seem to be more compatible with the various switches (including our SRW224P - that detects the MFEFX1 as a 1000M-ComboF device. I tried this before finding the above 'compatibility' document).
Can anyone supply me with some information so that I can get this fiber connection working? Trying to set any options on the SLM224P to tell it to use only a 100M connection gives an error about this being a 1G port and so can only run a 1G speed.
Thanks for any help

aponikikay, thanks for the feedback.
The document linked is the quick-start guide that came printed with the miniGBIC. I did see that list. It looks like the other document (Linksys100M-SFP-SwitchSupport-noteV1.3.pdf) might not be so acurate.
I am going to have the SLM switch replaced by a SRW224G4P that is listed as supported. I just wonder why I was supplied with the one set of equipment in the first place...

How can I have a text field that auto detects a previous entry?

Like I have a text field example "First Name" and I want to be able to add another text field that will auto detect that input.

Hi,
Sorry we do not support this.
To add a feature request please go to http://forums.adobe.com/community/formscentral?view=overview and click on "Submit Feature Request" in the Resources section on the right.
To vote for an existing feature request already entered in our database, please go to http://forums.adobe.com/community/formscentral?view=overview and click on "View Feature Request" in the Resources section on the right.
Thanks,
Lucia

GLC-SX-MM auto detecting as half duplex

Similar Messages

Maybe you are looking for