Global & Local controller

Hi Guys,
Am new to Mars, so execuse me if the question is simple.
i cannt understand what is the difference between global & local controller.
i've only one Mars appliance and want to connect it to the network, do i need to use global controller? or only the local? so, again what is the diference between the two controllers.
Thanks & Regards,
Ramii

If you only want 1 MARS, then you only need to get the Local Controller.
You would only need to get Global controller if you would like the Global controller to manage all your Local controllers.
Here is what the global controllers are capable off:
• Aggregation of reports across the Local Controller deployment
• Defining Rules, Reports and User accounts for Local Controllers (Note: Configuration of Local Controller is done "locally" on the individual LC appliance)
• Remote, distributed upgrade of the Local Controllers
Hope that helps.

Similar Messages

Global Controller - Local Controller authentication?

If you are logged onto the GC and you click on anything (incidents for example), you are redirected to one of the local boxes and asked to log in again. Is this normal operation, or can we pass thru the authentication somehow?

I should provide some details. I kind of doubt that the general concept has changed (i.e. you should not have to re-auth to the local controller). You have to touch local controllers far too often in the current distributed MARS model for this to be acceptable IMHO. Perhaps someone running the GC in production can correct me on this? It either requires re-auth or it doesn't...which is it?
I can't seem to find the directory where I stored my POC data. My recollection is this:
when you clicked on an incident in the GC, you hit a page on the GC (NOT the LC) that gave you a security/session identifier [quite possibly by fetching it from the LC] and were then redirected to the LC. The redirect request to the LC contained this session identifier. I can't remember if the session identifier is in the URL, or a cookie, or in POST data. It doesn't really matter though...the key is that the request to the LC already has a valid session id.

How to get my custom controller updated with the global custom controller?

Hi all,
I'm new to CRM Web UI and need some advice from the expert. Currently I'm working on component ICCMP_BT_DATES and noticed something weird with this component. When this component is first launch it display the dates of a service ticket correctly. However when I navigate to another screen, save a new ticket and back, the dates are not reflected. When I went in and debug the component, I noticed that the context is still tied to the previous ticket. I think the custom controller is not updated with the latest from the global custom controller.
My question is how do I get my custom controller updated with the latest.
Regards,
Ricky

You have to bind your custom controllers context node to the event NEW_FOCUS of the collection wrapper on the global custom controller.
Best place to do this might be the CONNECT_NODES of the context of your custom controller.
Get the global CuCo with GET_CUSTOM_CONTROLLER() and then the appropriate context node. Now:
SET HANDLER yourMethod for lr_global_cuco->typed_context->thecontextnode->collection_wrapper activation iv_activate.
Of course you have to implement a method similar to ON_NEW_FOCUS as it is on many other nodes.
cheers Carsten

Global, Local, Harmonised attributes.

Hi,
Could anybody explain me about the Global, Local, Harmonised attributes and how we should use them with Template project and Implementation project.
Regards,
Murali

You set these attributes against the nodes in your Template Project's Business Process Structure. The purpose of maintaining these attributes is to have control, or lend flexibility, to your rollout (implementation projects).
When you set an attribute of global it means that items cannot be changed and that they must be included as part of the implementation project. For example, if you maintain your Procure to Pay scenario (and all processes, steps beneath it) as global, the implementation project cannot change the scope, documents, configuration entries, transactions, or whatever else you attach.
Localizing items in the BPS allows flexibility for the implementation projects to change everything assigned at a local level.
You can also provide different flavors of these attributes. For example, you might set all of your scenarios and processes to global however the process steps performed in organizations around the globe will obviously not match a global "headquarters". For that reason you could set the process steps to Local.
Hope this helps,
Nathan

Urgent : OBIA - Handling multiple Global, Local and Document Currencies

All,
I need input on how to configure multiple currency codes in DAC for OBIA 7.9.6.x
My client's business goes around the the world and with multiple local currencies.They also need reporting currency to be multiple like in Euro, USD etc.
I went through a couple of threads in this forum,like -
Re: Configuring Global Currencies in BI Apps 7.9.6 for EBS 11.5.10 Source
Re: How we are using Global, Local and Document Currencies in DAC.
But I have some confusion regarding the configuration of DAC's 3 Global currency codes.
In order to fulfill my requirement - should I add additional codes in DAC?
Basically How am I supposed to handle multiple Local,Document and Global currencies? And then possible changes in rpd/reports required also?
Regards,
Krish

Currencies are discussed in the Setup and Configuration Guide here:
7.1.1.2 How to Configure Global Currencies
To configure the global currencies you want to report in your warehouse:
In the DAC Client, display the Design view.
For more information about logging into the DAC, see Section A.1, "How to Log Into the DAC Client".
Select a container from the drop down list to the right of the Execute button.
Display the 'Source System Parameters' tab.
Locate the following parameters and set the currency code values for them in the 'Value' box:
$$GLOBAL1_CURR_CODE (for the document currency).
$$GLOBAL2_CURR_CODE (for the local currency).
$$GLOBAL3_CURR_CODE (for the global currency).
Make sure that you spell the currencies as they are spelled in your source OLTP system.
Save your changes.
As far as for PLP items, those are Post Load Processing elements that perform cleanup tasks after the Base Warehouse tables have been loaded. They should never be modified and frankly run without any issues provided the rest of the plan executes properly. Do you have a specific quesiton about a PLP?

View (Global & Local) on a query

Hi,
I got a query with 60 Free chars(drill down)
Insted of creating a multiple queries of the same content ,My requirment is to create views (6) on a same query (easy in support point of view)
How can i create a view on a query
What is difference between Global & Local view
How to create them and
The views that i want to create users won't be authorised to change them
BW Version 7.0
Users access reports using WEB Bex
Please advise

Hi
How can i create a view on a query
After the execution of the report make the necessary drill down based on the Free char and Save that as a View using save view as Global.
Then when everyou open the View it will display the drill down that you saved by default.
Reggards
M.A

How to configure HA between local controller and remote controller in DC

Good day,
If I have two Cisco 5508 Controllers, running Software version 7.4, how would my failover happen when the AP's run in local mode, and the local controller fail, and you configured your remote controller as your secondary controller. Question is, will the APs automatically convert to FlexConnect mode when they failover to the remote controller in the DC? I know you cannot configure HA as the controllers have to be connected with ethernet copper cable on the redundancy port, giving you a distance limitation of 100m.
Thank you in advance
Adrian

Hello ,
As per your query i can suggest you the following solution-
In wireless network deployments that run controller versions earlier than 5.0, when a controller goes down, it takes a long time for all the APs and the associated clients to move to a backup controller and for wireless service to resume.
The features discussed in the document are implemented on the controller CLI in WLC software release 5.0 in order to decrease the time that it takes for access points and their associated clients to move to a backup controller and for wireless service to resume after a controller goes down:
In order to reduce the controller failure detection time, you can configure the heartbeat interval between the controller and access point with a smaller timeout value.
In addition to the option to configure primary, secondary, and tertiary controllers for a specific access point, you can now also configure primary and secondary backup controllers for a specific controller. If the local controller of the access point fails, it chooses an available controller from the backup controller list in this order:
•o primary
•o secondary
•o tertiary
•o primary backup
•o secondary backup
The access point maintains a list of backup controllers and periodically sends primary discovery requests to each entry on the list. You can now configure a primary discovery request timer in order to specify the amount of time that a controller has to respond to the discovery request of the access point before the access point assumes that the controller cannot be joined and waits for a discovery response from the next controller in the list.
Hope this will help you.

Wireless Management - Local Controller vs. Cloud

Good afternoon,
We are currently looking to upgrade (re-design) our wireless network at our college.
I was curious if anyone had any experience going from a local, controller-based wireless network to a cloud-based controller? If so, what have you found the pros and cons to be?
If you thought about going to a “cloud solution”, what stopped you?
In addition, any other feedback on Meracki, Aerohive, Aruba, or other solutions would be much appreciated.
About Us
We are currently running wireless at our 3 primary campus locations, and looking to add it to our 3 satellite locations.
We use 4402 WLCs at our primary locations with a mix of 1140 and 1240 APs.

The advantage of using local controller are
1.Lower Operational Expenses
2.Easier Way to Scale with Optimal Design
3.Single Location to Apply Wired and Wireless Services
In addition, certain controllers, such as Cisco Wireless Services Module (WiSM) blades on the Cisco Catalyst® 6500 Series Switches, perform various other functions, including application inspection using the Cisco Network Analysis Module, enhanced security with a full stateful firewall and intrusion detection system, and more. Placing the controller in a centralized location simplifies N+1 or N+N redundancy, depending on the size of the network. This redundancy means that for each wireless controller (N) there is at least one backup controller (+1). The backup controller is not positioned to actively contribute to normal system operation but provides a reliable way to protect the network in case of any failure or downtime on the component being used to manage network access
The advatage of using cloud based controller
1.The Cisco Flex 7500 Series Cloud Controllers are used for this.
2.you can consolidate multiple controllers in to one controller with support up to 6000 access points and 64,000 clients from data center
3.Gain significant saving in operatins by configuring , managing and troubleshooting 6000 AP's and 64,000 clients in single pint of touch
4. When traffic is directed to the controller in FlexConnect Central switched mode, the Flex7500 Series supports Application Visibility and Control (AVC). AVC includes the NBAR-2 engine, Cisco's deep packet inspection (DPI) capability that classifies applications, applies quality of service (QoS) to either drop or mark the traffic, and prioritizes business-critical applications in the network. AVC uses NetFlow Version 9 to export the flows. The Cisco Flex 7500 Series in central switched mode also supports Bonjour Services Directory to enable Bonjour Services to be advertised and utilized in a separate Layer 3

No snmp response from local controller only remote

2 controllers 1 remote. Remote controller communicates with WCS no issues. Local controller does not.
From earlier threads recommendations, 4.0.179.11 on controllers and 4.0.96 on WCS.
debug snmp on controller shows:
Mon Feb 26 17:40:29 2007: SNMPD: calling srDoSnmp.
Mon Feb 26 17:40:29 2007: Unknown engine Ids
Mon Feb 26 17:40:29 2007: SNMPD: Sending SNMP packet to 10.31.148.3:63499, out_p
acket_len = 108
Mon Feb 26 17:40:54 2007: SNMPD: Packet from: 10.31.148.3:63499, in_packet_len =
66
Mon Feb 26 17:40:54 2007: SNMPD: calling srDoSnmp.
Mon Feb 26 17:40:54 2007: Unknown engine Ids
Mon Feb 26 17:40:54 2007: SNMPD: Sending SNMP packet to 10.31.148.3:63499, out_p
acket_len = 108
Anyone run into this? Havent found anything yet in previous messages.
Thanks!

Hi
In AP Log AP is not sending LWAPP Join-Request .I think WLC is not getting Join Request from AP.I did only basic configuration.This is first Ap i am trying to register with controller.
Below is the debug of lwapp events in controller
Fri May 21 18:51:43 2010: 00:23:eb:1e:15:d0 Received LWAPP DISCOVERY REQUEST from AP 00:23:eb:1e:15:d0 to 00:26:cb:de:5d:c0 on port '1'
Fri May 21 18:51:43 2010: 00:23:eb:1e:15:d0 Successful transmission of LWAPP Discovery Response to AP 00:23:eb:1e:15:d0 on port 1

Help Document on Query View's (Global & Local)

Hi,
I thied to search SDN for previous posts on this topic but none of them are useful.
Is there any SAP Help Doc or any other Help Doc that will explain me difference between Local View & grobal View on a Query and
How to Generate Local View and Global View on a query in detail
Thanks

Hi,
Check the below doc:
Queries nd Query views:
http://help.sap.com/saphelp_nw70/helpdata/en/44/05b8d847bc6037e10000000a1553f6/frameset.htm
Reg
Pra

Store Counter Number in BODS using Global/Local Variable

Hi All,
Anyone done before adding a counter integer field into a table based on key via BODS?
Example:
Table 1 (contains just 1 field) <-Input:
Key 1
Key 1
Key 2
Key 2
Key 2
Table 2(contains 2 fields with INT as the 2nd field) <-Output:
Key 1      1
Key 1      2
Key 2      1
Key 2      2
Key 2      3
I was wondering if populating the Local Variable or Global Variable might work but from my understanding, inside the Data Flow , it's not possible to increase the variable value ($count = $count + 1).

Hi Maurice,
Thats a good idea!!
I had currently implemented a solution where i use Variables and Customize Functions to solve the problem.
Will give a try and see if your solution produce the same result.
Tim

How to: Transform Activity: Read global/local variable, execute java code

Could anyone please show me how to do that???

could you please elaborate your usecase? yes you can read global variable using getVariableData( ) xpath function and pass them as an argument to the processXSLT ( ) xpath function.
You can read the global or local variables inside java exec using, please refer samples/references/javaexec sample.

How we are using Global, Local and Document Currencies in DAC.

Hi All,
How we can configure Local,Global and Document currencies for GL Load.
and where we can use these parameters in informatica.
What does stand for PLP and what is logic behind PLP.
Thanks in advance
Thanks,
Bhavik

Currencies are discussed in the Setup and Configuration Guide here:
7.1.1.2 How to Configure Global Currencies
To configure the global currencies you want to report in your warehouse:
In the DAC Client, display the Design view.
For more information about logging into the DAC, see Section A.1, "How to Log Into the DAC Client".
Select a container from the drop down list to the right of the Execute button.
Display the 'Source System Parameters' tab.
Locate the following parameters and set the currency code values for them in the 'Value' box:
$$GLOBAL1_CURR_CODE (for the document currency).
$$GLOBAL2_CURR_CODE (for the local currency).
$$GLOBAL3_CURR_CODE (for the global currency).
Make sure that you spell the currencies as they are spelled in your source OLTP system.
Save your changes.
As far as for PLP items, those are Post Load Processing elements that perform cleanup tasks after the Base Warehouse tables have been loaded. They should never be modified and frankly run without any issues provided the rest of the plan executes properly. Do you have a specific quesiton about a PLP?

Global, local variables in SubVI's

Hi,
I'm having a problem with what is probably a 'feature' of labview
(using ver 6.1).
When running multiple SubVI's of the same type, any local variables
declared within the SubVI are globally scoped across all instances of
that SubVI within one VI. Is there any way to prevent this?
I am trying to store the Status of the SubVI in a local, but obviously
each instance of the SubVI ends up with the same status. Currently i
have solved this by having exact copies of the SubVI for each
instance, but obviuosly as far as labview is concerned they are now
different SubVI's, i consider this a bit of a hack and would rather
avoid it.
Any pointers?
Many Thanks,
Ed

If you make the sub-VI reentrant, you will get the type of local you're looking for. On the sub-VI's menus, goto File >> VI Properties >> Category >> Execution >> Reentrant Execution.

Xmlschema global/local issue(oracle10g)

I've schema with globally declared elements,something like:
<xs:schema xmlns:xs="http://www.w3.org/2001/XMLSchema" elementFormDefault="qualified" attributeFormDefault="unqualified">
     <xs:element name="el3" xdb:defaultTable="el3">
          <xs:complexType>
               <xs:sequence>
                    <xs:element name="el3_1"/>
                    <xs:element name="el3_2">
                         <xs:complexType>
                              <xs:sequence>
                                   <xs:element ref="el1" xdb:SQLInline="false" xdb:defaultTable="el1"/>
                                   <xs:element ref="el2" xdb:SQLInline="false" xdb:defaultTable="el2"/>
                              </xs:sequence>
                         </xs:complexType>
                    </xs:element>
               </xs:sequence>
          </xs:complexType>
     </xs:element>
     <xs:element name="el1" type="el1" xdb:defaultTable="el1"/>
     <xs:element name="el2" type="el2" xdb:defaultTable="el2"/>
</xs:schema>
as you can see local element "el3" references two global elements in declaration.
When I insert document corresponding to "el1" in "el1" table-all works as expected but when I try to insert conforming to "el3"(verified by xmlspy) document in "el3" document,oracle don't recognize "el1" and "el2" elements in context of "el3".By the way,how oracle handle situation with existent primary key in dependent table(SQLInline="false")?Will it try to reinsert element or use existent?
An at last, <xdb:tableProps="OBJECT IDENTIFIER IS PRIMARY KEY" construction> dosen't work at all though <xdb:columnProps="primary key"> seems work as expected.
Any thoughts?

Mark
Please can you confirm that I understand correctly your response which mentions a potential future enhancement.
I assume you are saying that it is currently not possible to override the default table name to place elements of the same type into a single table.
I used the following test XML schema:
<?xml version="1.0"?>


<xs:schema elementFormDefault="qualified" xmlns:xs="http://www.w3.org/2001/XMLSchema" xmlns:xlink="http://www.w3.org/1999/xlink" xmlns:xdb="http://xmlns.oracle.com/xdb">
     <xs:import namespace="http://www.w3.org/1999/xlink" schemaLocation="xlink.xsd"/>
     <xs:element name="COMPONENT">
          <xs:complexType>
               <xs:sequence>
                    <xs:element ref="Properties"/>
                    <xs:element ref="SCHEMATIC"/>
                    <xs:element ref="DOCUMENT"/>
                    <xs:element ref="DIAG-TREE"/>
                    <xs:element ref="SHORTCUT" minOccurs="0" maxOccurs="unbounded" xdb:SQLInline="false" xdb:defaultTable="SHORTCUT_TABLE"/>
               </xs:sequence>
          </xs:complexType>
     </xs:element>
     <xs:element name="DIAG-TREE">
          <xs:complexType>
               <xs:sequence>
                    <xs:element ref="Properties"/>
                    <xs:element ref="START"/>
                    <xs:element ref="TACTIC-NODE"/>
                    <xs:element ref="RETURN"/>
               </xs:sequence>
               <xs:attribute name="id" type="xs:string" use="required"/>
          </xs:complexType>
     </xs:element>
     <xs:element name="DOCUMENT">
          <xs:complexType>
               <xs:sequence>
                    <xs:element ref="Properties"/>
               </xs:sequence>
               <xs:attribute name="id" type="xs:string" use="required"/>
               <xs:attribute ref="xlink:href" use="required"/>
          </xs:complexType>
     </xs:element>
     <xs:element name="PresenterTactic">
          <xs:complexType>
               <xs:sequence>
                    <xs:element ref="actionItem"/>
               </xs:sequence>
          </xs:complexType>
     </xs:element>
     <xs:element name="Properties">
          <xs:complexType>
               <xs:sequence>
                    <xs:element ref="icon32" minOccurs="0"/>
                    <xs:element ref="name" minOccurs="0"/>
                    <xs:element ref="component" minOccurs="0"/>
                    <xs:element ref="SHORTCUT" minOccurs="0" maxOccurs="unbounded" xdb:SQLInline="false" xdb:defaultTable="SHORTCUT_TABLE"/>
               </xs:sequence>
          </xs:complexType>
     </xs:element>
     <xs:element name="RESULT">
          <xs:complexType>
               <xs:attribute name="ref" type="xs:string" use="required"/>
          </xs:complexType>
     </xs:element>
     <xs:element name="RETURN">
          <xs:complexType>
               <xs:attribute name="id" type="xs:string" use="required"/>
          </xs:complexType>
     </xs:element>
     <xs:element name="SCHEMATIC">
          <xs:complexType>
               <xs:sequence>
                    <xs:element ref="Properties"/>
                    <xs:element ref="SCHEMATIC-REF" maxOccurs="unbounded"/>
               </xs:sequence>
               <xs:attribute name="id" type="xs:string" use="required"/>
          </xs:complexType>
     </xs:element>
     <xs:element name="SCHEMATIC-REF">
          <xs:complexType>
               <xs:sequence>
                    <xs:element ref="Properties"/>
               </xs:sequence>
               <xs:attribute name="x">
                    <xs:simpleType>
                         <xs:restriction base="xs:NMTOKEN">
                              <xs:enumeration value="132"/>
                              <xs:enumeration value="252"/>
                         </xs:restriction>
                    </xs:simpleType>
               </xs:attribute>
               <xs:attribute name="y" type="xs:short"/>
          </xs:complexType>
     </xs:element>
     <xs:element name="SHORTCUT">
          <xs:complexType>
               <xs:attribute name="id" type="xs:string" use="required"/>
               <xs:attribute ref="xlink:href" use="required"/>
          </xs:complexType>
     </xs:element>
     <xs:element name="START">
          <xs:complexType>
               <xs:sequence>
                    <xs:element ref="RESULT"/>
               </xs:sequence>
               <xs:attribute name="id" type="xs:string" use="required"/>
          </xs:complexType>
     </xs:element>
     <xs:element name="TACTIC-NODE">
          <xs:complexType>
               <xs:sequence>
                    <xs:element ref="PresenterTactic"/>
                    <xs:element ref="RESULT"/>
               </xs:sequence>
               <xs:attribute name="id" type="xs:string" use="required"/>
          </xs:complexType>
     </xs:element>
     <xs:element name="actionItem">
          <xs:complexType>
               <xs:simpleContent>
                    <xs:extension base="xs:string">
                         <xs:attribute name="id" type="xs:string" use="required"/>
                    </xs:extension>
               </xs:simpleContent>
          </xs:complexType>
     </xs:element>
     <xs:element name="component">
          <xs:complexType>
               <xs:attribute ref="xlink:href" use="required"/>
          </xs:complexType>
     </xs:element>
     <xs:element name="icon32">
          <xs:complexType>
               <xs:attribute ref="xlink:href" use="required"/>
          </xs:complexType>
     </xs:element>
     <xs:element name="name">
          <xs:complexType>
               <xs:attribute ref="xlink:href" use="required"/>
          </xs:complexType>
     </xs:element>
</xs:schema>
The only important bit in this XML schema is that the SHORTCUT element can have more than one parent element (two in this example).
10.1.0.2.0 allowed me to register the XML schema above, but at runtime an error occurred when I attempted to insert the XML document via WebDAV. The insert works when I defined an XML Schema which uses different table names.
Sorry for asking for confirmation - this was potentially an important implementation requirement for us.
Just in case there is an obvious alternative implementation method, I'll briefly mention our real requirement. We were looking for a way to store our "xlink" references so that we can provide "re-factoring" capabilities for our XML documents. Our xml documents refer to each other using xlink attributes that contain relative paths (folder and file names). Our customers eventually will have 100,000+ XML documents, and therefore they are likely to wish to re-organise them.

Global & Local controller

Similar Messages

Maybe you are looking for