GNB MAX CPU Speed Problem

I'm repairing a computer with this specs:
Mainboard: GNB MAX v2
CPU: P4 2,8 GHz
512MB RAM 333Mhz
With standard bios settings, the pc is running at 1,4GHz! I can't get it to 2,8Ghz
Any idea's?
Thanks!

here are some screenshots from cpu-z

Similar Messages

Max cpu speed

My son has a compaq with a msi 6090 v3.0. The online manual says that it will support 2600+ or higher processor. But the MSI website says it will support 2200+ or higher. Doesn't sound like a big deal, but when i clicked on the relevant link entitled 'cpu support' it it had a "no" next to any processor with a higher speed than 2200+. Does anyone have any idea what the max cpu speed is that can be supported by this particular motherboard?
Thanks for any help.

CPU support for 6390 both 2 version is reported by BIOS ver:
BIOS Version:6390 ver1: W6390VMS.150 (ver. 1.50)
6390 ver2: W6390VMS.210 (ver. 2.10)
latest version on BIOS for 6390 ver1 is Version 1.8
latest version on BIOS for 6390 ver2 is Version 2.6(Update Description Support Duron Applebred FSB133 CPU)
if you update with latest BIOS for your mobo you may support higher CPUs
BIOS link here: http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=80&kind=1

K8T Neo-FIS2R V1.0, CPU Speed Problem

Hi, I got a Athlon64 3500+ (NewCastle) and K8T Neo-FIS2R V1.0 MotherBoard
Just downgrade my bios from 9.2 to 3.3 since the 9.2 bios does not show the correct +3v voltage in the core center and the website is recommending that old version of Athlon should use 3.xx bios.
But the problem occurs, the core center now shows the cpu speed is 1xx rpm and keep sending alarm. I use other software to check the fan speed and it is 2xxx rpm. The temp of the cpu is between 33 to 43 'C.The temp of the case stays at 42 'C. The voltage of the CPU is 1.52-1.53V. One time, somehow the temp of the cpu went up to 50'C but the fan is not turning faster to cool down the CPU. No matter what models (Cool&Quiet or User) I choose in the core center, it just did not go faster. Finally, I have set full speed of the fan in the core center to increase the speed of the fan.
My PSU is Enermax 450W, and I used 5V for my three case fans since they are really noise.
Any problems with my system or computer, or any recommemdation?
Sorry for my English, but I am doing my best.

Everest just has no readings that work for us. They never supported our board. None of the software gets a correct read on our 3.3v so no there is no answer. I have tried them all as have others. If reading the 3.3v is that important to you use a meter.
I have yet to ever trust Core Center. It lies. Keep in mind just how many MSI products it is used in. So far it has yet to be that accurate in any Via Based MSI product. Search the forum here for it. No one seems overjoyed with CC.

Tecra A8 - no max CPU speed under PowerSaver's "full power" profile

Hi Everyone,
My Tecra A8-S8514 (Core 2 Duo T7200 @ 2GHz) has this problem: when I set the PowerSaver profile to "Full Power" the CPU sets its speed to 1.4GHz.
My company bought 2 of A8's and the test was replicated in the second laptop, which leads me to believe there's a bug with the PowerSaver application instead of bad hardware.
The Toshiba phone support ignore the fact that 2 laptops have the same problem, insisted I should do a system restore and if that didn't fix the problem take it to a service center. There was no way the "experts" would admit the application could be wrong and submit a request to the programmers so they can test and engineer a fix.
Please can someone else with a Tecra A8-S8514 test this? I used the Intel Processor ID Utility and a free benchmark called GeekBench.
Thanks in advance!!!!

Hi, and thanks for your reply!
My CPU settings are set to "Dynamically Switchable" and the help file explains that this setting lets PowerSaver control the CPU frequency, so that's not part of the problem.
I see buggy software being released all the time and frequently wreaking havoc and causing chaos before the developers/publishers notice and take measures.
If Excel 2007 can't multiply correctly, PowerSaver can very well mismanage my laptop's CPU power, and I bet you Excel 2007 was tested more thoroughly than PowerSaver.
Like I said, I have 2 identical Tecra A8s and have replicated this issue on both. Do you have a Tecra A8-S8514 and have tested this?
Take a look at these screenshots, since they help illustrate the problem:
AC Optimized setting:
http://img529.imageshack.us/img529/2346/acoptimizedpowersavernr9.gif
http://img213.imageshack.us/img213/9249/acoptimizedvc2.gif
"Full Power" setting:
http://img526.imageshack.us/img526/3737/fullpowerpowersaverdp3.gif
http://img526.imageshack.us/img526/1210/fullpowerzn3.gif

Msi 990fx gd65 cpu speed problem p2x4 965

Hi im new here this is my first topic.
I buy a Msi 990fx gd65 board my problem is everytime when boot up the pc the cpu freq. is 800mhz (4x200) i disable every power saving option and cool n quit thing, i must every time in click bios to adjust the frequency to 17x200 and restart to be enabled, i have a latest bios 19.9 a cpu is p2x4 965 be rev c3, 2x4gbddr 1600 Msi gtx 580 twin frozer and a chieftec psu 600w.
The control center is installed and a click bios to.
Thanks for a help and sorry for a bad english writing when exist.

Quote from: mesco on 25-March-13, 04:57:09
I just updated the bios from 19.9 to 20.1 and i have a black screen on startup try to revert the older bios but not succes what can i do?
how did you correct this problem

Msi p45 neo3-fr (pcb1.0) + E8400 (E0) cpu speed problem

msi p45 neo 3 + E8400 (E0)
Bios version 1.5
I turn off intel eist in bios when use stock speed (3GHz) my cpuz (ver 1.46) show 333*6 = 2GHz although when I play games it run 333*9 =3GHz just like I turn on intel eist
But when I overclock (Ex 400*6 = 3.6GHz) my cpuz show 3.6 GHz
I want to know that why when I use stock speed it seem like I turn on intel eist
this is normal (but think is not) or there are problem with my main board
sorry for my bad english

Quote from: Jack the Newbie on 21-January-09, 19:23:40
I highly recommenend to keep the power saving functions enabled even if you are overclocking if the system does not become instable because of that. There is no point in high frequencies when the system has nothing to work with.
ok
there are another problem with bus ram when I set auto it show 1067 but in cpuz show 400(=800) i'm not sure but I think it come form bios ver 1.5(if it not I think have broblem again LoL)
because I remember that frist I buy it it show 800 in bios (when I buy it come with bios ver 1.2 that not support my E8400 E0)
I think next bios should solve it (1.6 didnt says about ram so I didnt do anything)

Max CPU Speed for MS 6131 Ver:2

I have a computer that I'd like to upgrade (slightly) with a faster CPU... I currently have a 550mhz PIII and want to know if I have room to put a faster PIII or Celleron or whatever in without getting a new motherboard.
The manual shows it has support for 233mhz and faster. Chipset is Intel 82440BX AGP. 66.6MHZ and 100MHZ sclocks are supported.
BIOs is award 4.51
If it matters, The current CPU is the old large brick (I Believe Slot 1). I don't know if that means coppermine or whatever (pardon my ignorance).
Plz advise! Thanks in advance for your help
Thanks,
Mark

I spoke with MSI and the fastest CPU officially supported is the 600MHz Katamai PIII.
If you flash the bios to a version that supports coppermine you should be able to get a celeron to run using a slocket card converter by setting the vcore manually to 1.80v but it could fail or even cause damage.

FSB/CPU Speed Problem Easy Fix Probly

I was fidlin' around in my bios and noticed that Im running at 1.34Ghz... which is strange for me, considering im running an AthlonXP 2200+, i played with the FSB Setting a bit, put it to 200, yet im still running at 1.34Ghz... This should be 1.8Ghz if im correct...
What exactly are the settings i need to change to get myself up to 1.8Ghz? I feel like a moron asking this since i should know it... heh
Thanks for the help though to those who give it.
System: (Just for reference)
Board: k7n2g-ILSR
CPU: AthlonXP 2200+
RAM: 1xCrucial 256MB PC2700

Sounds like you're running in safe mode Jumper J10 should be on pins 1&2. Jumper J11 should be shorted. I beleive the FSB for a 2200+ is 133.

Max CPU Supported?

Hi there,
Could someone tell me what is the max cpu speed supported for the msi 5182 (socket 7 & alladin 5 based) motherboard?
Thank you.

http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=230&NAME=MS-5182
1.4 Update date 1999-9-9
Update Description - Fixed Windows98(R)SE Standby problem
- AMD(R) K6-III 450MHz
best i can find

MOVED: A88XM Gaming and A8-7600 - CPU Max DDR Speed 2133Mhz

This topic has been moved to Overclocking, Undervolting.
https://forum-en.msi.com/index.php?topic=252580.0

Max RAM speed supported by memory controller in that CPU is 2133. Trying to squeeze 2400 speed is not worth the effort as you would never see any real world performance increase.
Any further questions/issues you may have re: OC it would be best for you to start a new topic in the OC section of the forum.

A88XM Gaming and A8-7600 - CPU Max DDR Speed 2133Mhz

I am running an A88XM with an A8-7600. I purchased 4gb x2 2400Mhz DDR3. When I enable XMP I get the message above, "CPU Max DDR Speed 2133Mhz" I read that the A8-7600 supported 2400mhz with AMP, so I purchased some AMD 2400mhz ram with AMD and I get the same message. It doesn't not allow me to manually select 2400 either. I'm wondering if anyone has any ideas or am I just missing something.
Thanks!

Max RAM speed supported by memory controller in that CPU is 2133. Trying to squeeze 2400 speed is not worth the effort as you would never see any real world performance increase.
Any further questions/issues you may have re: OC it would be best for you to start a new topic in the OC section of the forum.

Instalalation Problem - CPU speed

I am trying to install BAM 10.1.3.1.0 on WinXP Professional OS with 1.7 GHz CPU. But the installer says "CPU at least 1 GHz : Failed" and it stops, though the CPU is 1.7 GHz. (I have installed XE database on the same machine)
Earlier also I was trying to intstall, it was passing all such minimum requirements, though it was failing at some other subsequent point. But now its stopping at the minimum system requirements.
Could anyone please throw some light why its not able to read the CPU speed properly?

Pls ignore this thread.
There was some problem with my BIOS.
The prob is solved now

MSI 6565 GNB Max SATA problem

Hi I have just picked up a 6565 Gnb Max board, P4 2.4 ,533FSB MAxtor 120 Gb SATA HDD, Asus FX5200 Card, 1 gig Twinmos 266 DDR,
I cannot get the mobo to recognise the SATA HDD, there is nothing in the bios where I can turn on the SATA controller
(Integrated Peripherals) can anybody help?

I'm having the same problems.
GNB-Max board, Seagate 120GB SATA and Seagate 60GB PATA w/ SATA adaptor.
Regardless of how I connect the drive(s) to the Promise controller, they are not recognised. I've tried the 120GB on it's own on both SATA connectors, the 60GB on it's own and paired on the SATA connectors, and the 60GB on it's own on the PATA (IDE3) connector. At no point in time does the Promise controller dialogue even display during boot, so I can not configure the drive(s). I've tried the 60GB as master, slave and cable select in all scenarios.
The BIOS shows SATA enabled, and I've upgraded to the latest (2.30) BIOS, as well as trying older (2.0 & 2.1) BIOS revisions. All show the same symptoms.
Can anyone shed any light on how you get the Promise controller dialogue to show, or how to overcome the problem? I'd really like to get the 120GB drive working as my boot drive so I can reuse the current PATA drives elsewhere.

Help me i've got a problem with my cpu speed

I have bought prince of persia 2 and after the installation i want launch it but it indicates me I haven't the minimal configuration for the cpu speed(it's indicated 800mhz)
my config:
k8n neo platinum
amd 64 2800+ (fsb 200mhz and multiplier 9x in the bios 1.4)
1gb ddr 400
ati radeon 9800pro 128mb
i look for and i find : cpu-z indicates 200mhz for the fsb and 4x for the multiplier
the same thing when i launch corecenter
please help me

ok you're right i restore the correct frequency
thank you thank you thank you
but it's nevertheless strange my multiplier moved from 4x to 9x on account of cool and quiet

CPU Speed VS Heating problem

I had the firmware upgrade on my 2.16 MBP and it has performed very well, the CPU speed cuts back and usually runs at 1333 mHz and the CPU temp runs about 50 to 60 degrees C. Recently it began running at 2167 100% of the time and, of course, the CPU temp is running in the 80 degree C region.
Same apps being used, no new software installed. What gives? I certainly would like to have it return to the older cooler running mode.
Thanks for any assistance or suggestions.
J Freitag

No viable options to date although you may want to keep this in mind. Apple has made changes to the firmware and system management control so that you may safely utilize the performance you paid for. You may not notice it now although when Leopard is released, you may appreciate the maximum performance of your Mac with the current updates, as it is now able to run the more robust and demanding operating system of the future.
http://www.apple.com/macosx/leopard/index.html
Regards,
 MBP-15"/2.16/2GB RAM/7200/W8612... Mac OS X (10.4.8) G4 Tower (OS 9/10), Dell 620 WorkStation (XP Pro), Gateway P4 (XP Home)

GNB MAX CPU Speed Problem

Similar Messages

Maybe you are looking for