GNOME, nautilus, devicekit-disks: mount USB disk

Hi,
I recently upgraded and have now nautlius 2.28.2-1 together with devicekit-disks 009-1 installed.
As usual mounting/unmounting USB disks in nautilus stopped working. I searched the wiki, forums, bugs and google to gather information about this topic, but you know ...
When I try to mount a disk (they all show up in nautilus) nautilus pops up an error declaring me "Not Authorized". After quite some reading I think nautilus now uses devicekit-disks to actually mount my USB disks, so I tried to mount it with devicekit-disks:
[resi@nomad ~]$ devkit-disks --mount /dev/sdc
Mount failed: Not Authorized
In older versions of nautilus I used to edit some files in /etc to grant myself permissions (PolicyKit.conf), but this does not work anymore.
I found a hint and edited /usr/share/polkit-1/actions/org.freedesktop.devicekit.disks.policy (this one is coming with devicekit-disks) and modified the default for the actions org.freedesktop.devicekit.disks.filesystem-mount action:
<allow_any>yes</allow_any>
Having done so I can now mount the USB disks using nautilus, devicekit-disks or palimpsest (suffering from the same "Not Authorized" problem). Unmounting has a little flaw though, it seems like nautilus tries to eject the medium when unmounting, but then again its "Not Authorized" to do so.
However, this is the only solution I could come up with. Since the file I modified will probably be replaced without notice during the next upgrade I fear I will have to go all the way again, not remembering anymore what I did to fix this (otoh, after writing this I probably will).
And since the values in org.freedesktop.devicekit.disks.policy are declared as defaults (and by the fact it lives under /usr) I assume there has to be a site configuration file somewhere in /etc.
Where should I but my customizations? I mean, whats the proper way to do so?
Thanks,
Christoph
P.S.: I like nautilus, it makes me unhappy to use thunar/pmount/whatever to mount my disks.

me again ... this whole *kit stuff seems so odd to me.
I finally read all the devicekit, then the policykit docs, Syu-ed and have now devicekit-disks 009-3 installed.
Using polkit-actions without arguments prints a list of registered actions (known to policykit). This list was pretty short:
[resi@nomad ~]$ polkit-action
org.freedesktop.policykit.read
org.freedesktop.policykit.revoke
org.freedesktop.policykit.grant
org.freedesktop.policykit.modify-defaults
PolicyKit considers all *.policy files under /usr/share/PolicyKit/policy/, only the policykit package installs its files (well, its one file) there.
devicekit-disks (and probably some other packages providing *.policy files) seems to forget about that. So I added a symlink:
[root@nomad policy]# ln -s /usr/share/polkit-1/actions/org.freedesktop.devicekit.disks.policy /usr/share/PolicyKit/policy/
Thats not enough, the file seems to be out of date. I had to replace all auth_admin_keep defaults with auth_admin_keep_session until the file validated.
And hurray:
[resi@nomad ~]$ polkit-action
org.freedesktop.policykit.read
org.freedesktop.policykit.revoke
org.freedesktop.policykit.grant
org.freedesktop.policykit.modify-defaults
org.freedesktop.devicekit.disks.filesystem-mount
org.freedesktop.devicekit.disks.filesystem-mount-system-internal
org.freedesktop.devicekit.disks.filesystem-check
org.freedesktop.devicekit.disks.filesystem-check-system-internal
org.freedesktop.devicekit.disks.filesystem-unmount-others
org.freedesktop.devicekit.disks.filesystem-lsof
org.freedesktop.devicekit.disks.filesystem-lsof-system-internal
org.freedesktop.devicekit.disks.drive-eject
org.freedesktop.devicekit.disks.drive-detach
org.freedesktop.devicekit.disks.change
org.freedesktop.devicekit.disks.change-system-internal
org.freedesktop.devicekit.disks.drive-ata-smart-refresh
org.freedesktop.devicekit.disks.drive-ata-smart-selftest
org.freedesktop.devicekit.disks.drive-ata-smart-retrieve-historical-data
org.freedesktop.devicekit.disks.luks-unlock
org.freedesktop.devicekit.disks.luks-lock-others
org.freedesktop.devicekit.disks.linux-md
org.freedesktop.devicekit.disks.cancel-job-others
org.freedesktop.devicekit.disks.inhibit-polling
org.freedesktop.devicekit.disks.drive-set-spindown
polkit-auth shows my authorizations, thus:
[resi@nomad ~]$ polkit-auth | grep mount
org.freedesktop.devicekit.disks.filesystem-mount
org.freedesktop.devicekit.disks.filesystem-mount-system-internal
org.freedesktop.devicekit.disks.filesystem-unmount-others
It seems to me that I am authorized for all actions listed above, I guess thats because this user is in both the wheel and root groups.
However, when I try to actually mount something nothing has changed.
[resi@nomad ~]$ devkit-disks --mount /dev/sdc
Mount failed: Not Authorized
Since policykit is now properly configured I can use polkit-action or polkit-gnome-authorization to modify the default values in the way polkit expects me to (not tampering with with the *.policy files).
[resi@nomad ~]$ polkit-action --action org.freedesktop.devicekit.disks.filesystem-mount
action_id: org.freedesktop.devicekit.disks.filesystem-mount
description: Mount a device
message: Authentication is required to mount the device
default_any: yes (factory default: no)
default_inactive: yes (factory default: no)
default_active: yes
But even now mounting fails because I'm not authorized.
Back to the start, if I change the factory defaults in org.freedesktop.devicekit.disks.policy mounting succeeds.
I think there might be 2 bugs involved here:
1.) missing links to policy files in /usr/share/PolicyKit/policy/
2.) policykit fails to consider overrides for factory defaults
What do you think?

Similar Messages

[SOLVED][XFCE] Cannot mount usb disks & manage network connections

Hi guys,
I'm using XFCE with 3.3.1-1 kernel. Since yesterday I'm not able anymore to automatically mount usb disks, manage my WiFi networks (networkmanage connects to the default access point but I can't select another AP nor editing my settings). I'm also prompted to type my password when I clik on the shutdown icon;
So it seems I lost some privileges but I can't figured out why...
I still belong to the same grousp as before:
[root@archLaptop sclarckone]# groups sclarckone
lp wheel games video audio optical storage scanner power users
Does anybody has an idea where to take a look?
Thanks
Last edited by sclarckone (2012-04-15 20:54:38)

Me too. Start a new thread?
Edit; Nope, this worked for me https://bbs.archlinux.org/viewtopic.php?id=142110
Last edited by Glinx (2012-05-25 11:44:47)

Cannot mount USB disk in SIngle-user mode (solaris 10)

Hi all ,
I need some help please :
I can read/write to my USB disks when i'm in muti-user mode but when to I swith to single-user mode ( init S ), I cannot mount it.
in Single-user mode , i started volume management daemon :
#/etc/init.d/volgmt start
#volcheck
but i'm still not able to mount it.
I tried to mount manually:
#mount /dev/dsk/c2t0d0p0 /testpoint , i have this error: < mount : not a UFS magic number ( 0x0) , dev/dsk/c2t0d0p0 is not of this fstype.
My system recognizes the USB device though in single-user mode:
This is an output of #iostat -En
c2t0d0 Soft Errors: 1 Hard Errors: 0 Transport Errors: 0
Vendor: BUFFALO Product: ClipDrive Revision: 2.00 Serial No:
Size:0.07GB <65339392 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 1 Predictive Failure Analysis: 0

Hi ,
thanks for your advice. My problem is resolved.
The USB drive was actually a FAT filesystem.
so I did # mount -F pcfs /dev/dsk/c2t0d0p0:c /testpoint and everything went fine
I can read/write to my USB disks when i'm in
muti-user mode but when to I swith to single-user
mode ( init S ), I cannot mount it.
in Single-user mode , i started volume management
daemon :
/etc/init.d/volgmt start
#volcheck
but i'm still not able to mount it.It probably requires other items to be started
first.
I tried to mount manually:
#mount /dev/dsk/c2t0d0p0 /testpoint , i have
this
error: < mount : not a UFS magic number ( 0x0) ,
dev/dsk/c2t0d0p0 is not of this fstype.
Looks like it's assuming UFS. If this is a pcfs
filesystem, give it the type on the mount line.
# mount -F pcfs /dev/dsk/c2t0d0p0 /testpointYeah, this was the right command, I had to specify option < -F pcfs >.
but I read somethere on this forum i had to specify :c as the drive for FAT at the end of c2t0d0p0 , so the full command was:
# mount -F pcfs /dev/dsk/c2t0d0p0:c /testpoint
>
DarrenThanks,
Sakolan.

Mount usb disk after boot

Hi,
How can I mount automatically an usb disk after boot?
Any suggestion would be appreciated.
Thanks

Read this fine article and use it to set up a udev rule, to specifically name the device. (Otherwise you may never know where it pops up in the disk naming scheme.)
Also note -- after reading the article -- there are plenty of examples of rules in /etc/udev/ files that may further help.

Can't mount USB disk with the atribute of fix and read-only

Hello All,
I have a usb disk which is set as fix(non-removalbe) and read-only. I tried to connect it to Macbook version 10.4.11 ,but it failed to mount the disk. However, connecting to 10.5.X and windows XP work fine. I am wondering is it a bug specifically in 10.4.11 only ? Could I get any patch for this problem ?
Thanks,
Ying

HI Ying and Welcome to Apple Discussions ...
Try repairing disk permissions.
Quit any open applications/programs. Launch Disk Utility. (Applications/Utilities) Select MacintoshHD in the panel on the left, select the FirstAid tab. Click: Repair Disk Permissions. When it's finished from the Menu Bar, Quit Disk Utility and restart your Mac.
Carolyn

Can not mount USB disks with Disk utulity

Today I received finally received the new Airport Extreme. I had no problems installing it in my WDS wireless net and combining it with the Airport Express.
BUT... mounting disk does not work.
I have 3 USB 2.0 Disk: 2 x Maxtor and one WD. All of them are seen by the Airport utility, but do not show up in the Disk Utilty on none of my Macs.
I realy tried everything:
- connecting them all at the same time using a USB 2.0 hub,
- connecting them one by one using an USB cable,
- reformating on my mac using Mac OS Extended (journaled) and connecting them,
- renaming the names of the disk to simple names: no space, no numbers,
- renaming the BaseStation.
No result, the onlything I see apearing in the Disk Utility Menu is the name of the BaseStation. If I click on this, a "Login" dialog box is displayed, if I try to login (all options tested) no result, and after a long time-out sometimes a message is displayed Not able to mount "drive-name.
Is there somebody who knows what to do?
Regards, Marc
2 x iMac G5; 2 x MacBook, iMac G4 Mac OS X (10.4.8)

After you reformatted did you by chance add any files while directly attached to your mac.
Network drives won't show in disk utility, use airport disk utility to find them and have them mounted or use the network list in your finder.

Automount Issue on Gnome 2.28: GDM Mounts USBs after 2nd Insert

Good evening everyone (at least, it's evening here at my part of the Universe),
I have been using Arch for the past month (and Ubuntu/Debian for two years) but am totally stumped on this odd behavior.
When I first installed Gnome, I got that 'Permission denied' dialog box everytime I tried to mount a USB, but quickly realized that it was because of the wrong exec line at the start of my .xinitrc. When I changed it to
exec ck-launch-session gnome-session
I thought everything would be fine. However, for a USB to automount, I have to insert the USB TWICE. I don't know why. The first time, it's detected by 'lsusb', but not by Nautilus (it doesn't even show up in the Computer directory).
lsusb
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 005: ID 3538:0059 Power Quotient International Co., Ltd
Bus 001 Device 002: ID 0402:5602 ALi Corp. Video Camera Controller
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
In this case, it's the Power Quotient International USB that isn't being read. When i remove the USB and put it back, it automounts.
I have checked previous threads and most of them discuss the 'Permission denied' issue, which is not the same as this one :( I have also checked the 'I Won the Struggle Between HAL and PolicyKit' - I don't think I have the same problem.
I have installed gnome-volume-manager.
I have tried this issue on another user account, but it's still the same - takes 2 inserts of the USB to make it mount.
I am a member of the storage and power groups.
If there are any other logs that I should show, I would be happy to show them, but am unsure if I should post PolicyKit files (I'm not sure which one is in charge of drive automounting, I'm sorry) or if I should post my HAL configuration file, but so far I have checked my HAL config file and it is configured as was written in the HAL wiki.
If someone could please point me in the right direction of what file(s) to look at (is this perhaps a HAL issue? or Xorg? or PolicyKit?) I would be happy to look into it again and post the appropriate files.
Thank you very much! :)
Last edited by luvien (2009-12-02 12:41:51)

@Allan:
Good point. That was a bit far fetched to say; I'll admit that. I should've looked at a roadmap or something. Maybe I was just unclear as to how much work distro developers were putting into customizing their rendition of gnome. Was unaware that installing a vanilla version of gnome would be unstable, wonder how the devs of gnome feel when working on a vanilla code base. .. oh well.
@smakked:
Maybe something's like window positioning is a little obsessive compulsive of me but that functionality was available in 2.26 and below; that's maybe why it seems unfinished or something. I'm not a n00b in any sort, I respect and understand opensource and such. I know that my post above sounds rather complain-oriented, but in all honesty, It's very MS like that newer software doesn't work as well (and sometimes worse) than previous versions. I just love gnome and can't use it because of some simple features that were taken away/ are not working.
@Both of you:
Creating a tab in nautilus then dragging the tab, segfaults nautilus. GDM segfaults if trying to log into gnome-session when the user is not part of 'wheel' ... just stuff like that. I've pulled the gnome packages on 3 different boxes (and 3 different CURRENT mirrors)... same issues. I know how to manage groups and permissons and basic packages to make arch work.
So, I'm very sorry to sound annoying or anything of that nature. I was mainly curious if anyone else is having issue / knew a way to fix them. I know most arch users love *box window managers and the like, but SOME of you have to have gnome and notice things like that. lol. Anyways, It's clear that I might get talked down to on here or might get accused of being pedantic when things don't work. Thanks anyways guys.
--Anthony C

How I can open my project from usb disk?

I copy my project from hard disk to usb disk because I have just 128 Gb on my HDD. Now I would like to open and change few details in my project and I can't find a way to open it. Could you please help me?

What exactly did you copy? You could do this from inside FCP. If you do it in the Finder the whole project folder has be be moved into a folder called Final Cut Projects at the root level of the external drive.

[SOLVED] How to automatically mount USB drives with custom mount point

edit:
Original title was : 'Unable to mount USB disk via /etc/rc.local', but got changed since the /etc/rc.local problem isn't relevant for me anymore.
Hello,
Since I am new to this forum, I'll start off with this :
Thanks to archlinux, its founder and all its contributors, cause this is the operating system (flavour) that annoys me the least.
The root problem :
I want to automount USB storage devices to other places than /media/ and without the need for programs that depend on gnome and the like. As I tried some stuff with hald and such, I didn't really get to a nice and easy to configure solution. Any hints in that direction are always welcome.
For now, automount of known USB storages devices during boot, will do.
So the things I tried and didnt work :
1.
Provide the disk info to /etc/fstab (via the disks UUID and 'auto' filesystem)
Add 'mount /mountpoint' to /etc/rc.local
Result : the mount command in rc.local says '... specify filesystem'
However, after boot, running /etc/rc.local mounts the USB disks correctly.
2.
Provide the disk info to /etc/fstab (via the disks UUID and the correct filesystem)
Add 'mount /mountpoint' to /etc/rc.local
Result : pc doesn't get through boot process and gives me the 'ctrl-d to reboot or root passwd for maintenance'
3.
Provide no disk info in /etc/fstab
Add the full mount line to /etc/rc.local (mount -t fs /dev/disks/by-uuid/MyUUID /MyMountpoint )
Result : don't remember the output of the mount execution, but well, it didn't mount
However, after boot, running /etc/rc.local mounts the USB disks correctly.
Is there something that isn't loaded at the time of rc.local execution that I need for mounting of USB devices ? Or why else is this failing ?
Regards,
BasiK
Last edited by BasiK (2009-08-28 07:22:50)

Thanks for the hint hunterthomson, but the pc I will be using it on, is an own-built HTPC/home file server, so there is no way I want to use a graphical file manager to get the usb disks mounted.
I tried to figure out a little about udev rules, and I got to do what I wanted to do, so thx for pointing me in that direction Mr.Elendig.
Btw, I am indeed also using auto-sleep/park disks, but this udev way works perfectly.
I added two rules files to /etc/udev/rules.d/ :
The first for a known usb disk (with its volume uuid), with a named mountpoint under my media dir /symbiosis/ :
[basik@plox ~]$ cat /etc/udev/rules.d/80-usb-utopia.rules
ACTION=="add", KERNEL=="sd[b-z][0-9]", ENV{ID_FS_UUID}=="a59332c2-07ba-4c52-afb5-20e361bdf71a",SYMLINK+="usb-%n", GROUP="storage", NAME="%k"
ACTION=="add", KERNEL=="sd[b-z][0-9]", ENV{ID_FS_UUID}=="a59332c2-07ba-4c52-afb5-20e361bdf71a",RUN+="/bin/mkdir -p /symbiosis/utopia"
ACTION=="add", KERNEL=="sd[b-z][0-9]", ENV{ID_FS_UUID}=="a59332c2-07ba-4c52-afb5-20e361bdf71a", RUN+="/bin/mount -t auto -o rw,noauto,sync,dirsync,noexec,nodev,noatime /dev/%k /symbiosis/utopia", OPTIONS="last_rule"
ACTION=="remove", KERNEL=="sd[b-z][0-9]", ENV{ID_FS_UUID}=="a59332c2-07ba-4c52-afb5-20e361bdf71a", RUN+="/bin/umount -l /symbiosis/utopia", OPTIONS="last_rule"
The second for unknown usb disks, to mount under the same dir. This is simply taken from the archwiki http://wiki.archlinux.org/index.php/Ude … .26_Tricks
Make sure these rules are executed after the ones for specific usb disks.
[basik@plox ~]$ cat /etc/udev/rules.d/usb-disks.rules
KERNEL=="sd[a-z]", NAME="%k", SYMLINK+="usb%m", GROUP="storage", OPTIONS="last_rule"
ACTION=="add", KERNEL=="sd[a-z][0-9]", SYMLINK+="usb%n", GROUP="storage", NAME="%k"
ACTION=="add", KERNEL=="sd[a-z][0-9]", RUN+="/bin/mkdir -p /symbiosis/usb%n"
ACTION=="add", KERNEL=="sd[a-z][0-9]", RUN+="/bin/mount -t auto -o rw,noauto,sync,dirsync,noexec,nodev,noatime /dev/%k /symbiosis/usb%n", OPTIONS="last_rule"
ACTION=="remove", KERNEL=="sd[a-z][0-9]", RUN+="/bin/umount -l /symbiosis/usb%n"
ACTION=="remove", KERNEL=="sd[a-z][0-9]", RUN+="/bin/rmdir /symbiosis/usb%n", OPTIONS="last_rule"
These may not be the nicest looking udev rules, but it works for what I wanted to do with it.

Disk Utility: Two disks show per disk. Repair which one?

Greetings,
In Disk Utility, for every disk mounted two disks are listed. One indented under the first. The first seems to represent the physical disk, and the second the volume on the disk.
But the buttons say "Disk" in bother cases, and in any instructions, including Disk Utility help, it never indicates which one to select.
Which one should be selected when instructions say to click "Repair Disk"?
Thanks

The unindented item is the physical drive entry. The indented item is the logical volume or volumes on the drive. When only one volume is listed repairing the volume may be done by selecting either entry. However, if you have more than one volume on the drive, then you should select the specific volume you need to repair. To repair permissions you must select the volume regardless of how many volumes are on the drive.

USB disk won't mount on startup (have tried everything)

Hi!
I'm having big problems getting my USB disk to mount on startup.:(
It used to work perfectly by having 'mount /dev/sdc1 /media/disk' in rc.local (and umount in local.shutdown) but recently it started saying that 'filesystem type must be defined' (or something like that). So I changed the line to 'mount -t ext3 /dev/sdc1 /media/disk' but now I get a message that '/dev/sdc1 does not exist'.
So I decided to get this fixed in fstab once and for all.
I checked the designations of the disks with 'fdisk -l' and noticed that the USB disk would alternate between /dev/sdc, /dev/sde and /dev/sdd quite random on every reboot. In other words I couldn't mount it in fstab by using one of those paths cause I'd get the same problem with '/dev/sdc or -e or -d does not exist'. I figured the sollution must be to mount the disk by using UUID. I checked the uuid's and got the following (as you can see the USB disk is on this reboot registered as '/dev/sde'):
bash-3.2$ ls -l /dev/disk/by-uuid/
total 0
lrwxrwxrwx 1 root root 10 2009-02-07 11:56 6cf5e803-429a-44c3-bcf9-0f007df623f3 -> ../../sda1
lrwxrwxrwx 1 root root 10 2009-02-07 11:56 8ef6be20-ee30-4a00-8946-56a4d94a7245 -> ../../sda3
lrwxrwxrwx 1 root root 10 2009-02-07 11:56 947b3b86-8501-4011-9da2-4de45eb4ed60 -> ../../sda2
lrwxrwxrwx 1 root root 10 2009-02-07 11:56 94911fb3-def7-4440-b6a5-5e09f91b19f6 -> ../../sde1
lrwxrwxrwx 1 root root 10 2009-02-07 11:56 acd197d3-f63e-48f9-88de-41eff1b3b425 -> ../../sda4
lrwxrwxrwx 1 root root 10 2009-02-07 11:56 b6745703-bde6-44ef-865d-d09501ecc8ab -> ../../sdb1
I other words the UUID of the disk should be '94911fb3-def7-4440-b6a5-5e09f91b19f6' so I added that to the fstab file, but I still get the same error that the disk doesn't exist. How is this possible? Isn't the UUID supposed to be the same no matter what? When the disk is clearly labeled with this UUID every time I check it why can't it be used in fstab??
Here's my fstab (I've commented out the lines that I've been trying out):
# /etc/fstab: static file system information
# <file system> <dir> <type> <options> <dump> <pass>
none /dev/pts devpts defaults 0 0
none /dev/shm tmpfs defaults 0 0
/dev/cdrom /mnt/cdrom iso9660 ro,user,noauto,unhide 0 0
/dev/dvd /mnt/dvd udf ro,user,noauto,unhide 0 0
/dev/sda1 /boot ext2 defaults 0 1
/dev/sda2 / ext3 defaults 0 1
/dev/sda3 /var reiserfs defaults 0 1
/dev/sda4 /home ext3 defaults 0 1
/dev/sdb1 /extra ext3 defaults 0 1
#/dev/sdc1 /media/disk defaults 0 0
#UUID=94911fb3-def7-4440-b6a5-5e09f91b19f6 /media/disk defaults 0 0
What am I doing wrong here? I've also tried to use different options like 'rw,auto,exec' but it won't work.

It seems I'm able to mount the disk from the terminal by doing '# sudo mount UUID=94911fb3-def7-4440-b6a5-5e09f91b19f6 /media/disk'.
But this only works when I do it manually. Adding 'mount UUID=94911fb3-def7-4440-b6a5-5e09f91b19f6 /media/disk' to rc.local only gives the error that filesystem must be defined and when it's defined I get the error that device is not found.
How can it work manually, but not in fstab or rc.local?
Here's my dmesg:
BIOS EBDA/lowmem at: 0009f800/0009f400
Linux version 2.6.28-ARCH (root@T-POWA-LX) (gcc version 4.3.3 (GCC) ) #1 SMP PREEMPT Mon Feb 2 22:22:59 UTC 2009
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fef0000 (usable)
BIOS-e820: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
BIOS-e820: 000000007fef3000 - 000000007ff00000 (ACPI data)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
DMI 2.4 present.
Phoenix BIOS detected: BIOS may corrupt low RAM, working it around.
last_pfn = 0x7fef0 max_arch_pfn = 0x100000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Scanning 0 areas for low memory corruption
modified physical RAM map:
modified: 0000000000000000 - 0000000000010000 (reserved)
modified: 0000000000010000 - 000000000009f400 (usable)
modified: 000000000009f400 - 00000000000a0000 (reserved)
modified: 00000000000f0000 - 0000000000100000 (reserved)
modified: 0000000000100000 - 000000007fef0000 (usable)
modified: 000000007fef0000 - 000000007fef3000 (ACPI NVS)
modified: 000000007fef3000 - 000000007ff00000 (ACPI data)
modified: 00000000e0000000 - 00000000f0000000 (reserved)
modified: 00000000fec00000 - 0000000100000000 (reserved)
kernel direct mapping tables up to 377fe000 @ 10000-16000
RAMDISK: 7fe0e000 - 7fedf2e4
Allocated new RAMDISK: 0055f000 - 006302e4
Move RAMDISK from 000000007fe0e000 - 000000007fedf2e3 to 0055f000 - 006302e3
ACPI: RSDP 000F8600, 0014 (r0 HP-CPC)
ACPI: RSDT 7FEF3040, 0038 (r1 HP-CPC AWRDACPI 42302E31 AWRD 0)
ACPI: FACP 7FEF30C0, 0084 (r2 HP-CPC AWRDACPI 42302E31 AWRD 0)
ACPI: DSDT 7FEF31C0, 3C55 (r1 HP-CPC AWRDACPI 1000 MSFT 100000E)
ACPI: FACS 7FEF0000, 0040
ACPI: SSDT 7FEF6F40, 01CA (r1 HP-CPC POWERNOW 1 LTP 1)
ACPI: SRAT 7FEF7180, 00A0 (r1 HP-CPC HAMMER 1 AMD 1)
ACPI: MCFG 7FEF7280, 003C (r1 HP-CPC AWRDACPI 42302E31 AWRD 0)
ACPI: APIC 7FEF6E80, 0068 (r1 HP-CPC AWRDACPI 42302E31 AWRD 0)
ACPI: Local APIC address 0xfee00000
1158MB HIGHMEM available.
887MB LOWMEM available.
mapped low ram: 0 - 377fe000
low ram: 00000000 - 377fe000
bootmap 00012000 - 00018f00
(9 early reservations) ==> bootmem [0000000000 - 00377fe000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000100000 - 000055b520] TEXT DATA BSS ==> [0000100000 - 000055b520]
#4 [000055c000 - 000055f000] INIT_PG_TABLE ==> [000055c000 - 000055f000]
#5 [000009f400 - 0000100000] BIOS reserved ==> [000009f400 - 0000100000]
#6 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000]
#7 [000055f000 - 00006302e4] NEW RAMDISK ==> [000055f000 - 00006302e4]
#8 [0000012000 - 0000019000] BOOTMAP ==> [0000012000 - 0000019000]
found SMP MP-table at [c00f46e0] 000f46e0
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x000377fe
HighMem 0x000377fe -> 0x0007fef0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0007fef0
On node 0 totalpages: 523903
free_area_init_node: node 0, pgdat c0406600, node_mem_map c1000200
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3951 pages, LIFO batch:0
Normal zone: 1744 pages used for memmap
Normal zone: 221486 pages, LIFO batch:31
HighMem zone: 2318 pages used for memmap
HighMem zone: 294372 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
SB4X0 revision 0x11
Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 80000000 (gap: 7ff00000:60100000)
PERCPU: Allocating 36864 bytes of per cpu data
NR_CPUS: 16, nr_cpu_ids: 2, nr_node_ids 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519809
Kernel command line: root=/dev/sda2 ro quiet
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Fast TSC calibration using PIT
Detected 2188.552 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Scanning for low memory corruption every 60 seconds
Memory: 2072040k/2096064k available (2227k kernel code, 22632k reserved, 1026k data, 332k init, 1186760k highmem)
virtual kernel memory layout:
fixmap : 0xffee8000 - 0xfffff000 (1116 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
.init : 0xc0433000 - 0xc0486000 ( 332 kB)
.data : 0xc032cfd9 - 0xc042db5c (1026 kB)
.text : 0xc0100000 - 0xc032cfd9 (2227 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Calibrating delay loop (skipped), value calculated using timer frequency.. 4378.48 BogoMIPS (lpj=7295173)
Security Framework initialized
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20080926
ACPI: Checking initramfs for custom DSDT
..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ stepping 01
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4379.66 BogoMIPS (lpj=7295468)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ stepping 01
Brought up 2 CPUs
Total of 2 processors activated (8757.15 BogoMIPS).
net_namespace: 768 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG for extended config space
PCI: Using configuration type 1 for base access
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: reg 18 io port: [0x4100-0x411f]
pci 0000:00:00.0: reg 1c 64bit mmio: [0xe0000000-0xffffffff]
pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:12.0: reg 10 io port: [0xfe00-0xfe07]
pci 0000:00:12.0: reg 14 io port: [0xfd00-0xfd03]
pci 0000:00:12.0: reg 18 io port: [0xfc00-0xfc07]
pci 0000:00:12.0: reg 1c io port: [0xfb00-0xfb03]
pci 0000:00:12.0: reg 20 io port: [0xfa00-0xfa0f]
pci 0000:00:12.0: reg 24 32bit mmio: [0xfe02f000-0xfe02f1ff]
pci 0000:00:12.0: reg 30 32bit mmio: [0x000000-0x07ffff]
pci 0000:00:12.0: supports D1 D2
pci 0000:00:13.0: reg 10 32bit mmio: [0xfe02e000-0xfe02efff]
pci 0000:00:13.1: reg 10 32bit mmio: [0xfe02d000-0xfe02dfff]
pci 0000:00:13.2: reg 10 32bit mmio: [0xfe02c000-0xfe02cfff]
pci 0000:00:13.2: supports D1 D2
pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
pci 0000:00:13.2: PME# disabled
pci 0000:00:14.0: reg 10 io port: [0x500-0x50f]
pci 0000:00:14.0: reg 14 32bit mmio: [0xfe02b000-0xfe02b3ff]
HPET not enabled in BIOS. You might try hpet=force boot option
pci 0000:00:14.1: reg 10 io port: [0x00-0x07]
pci 0000:00:14.1: reg 14 io port: [0x00-0x03]
pci 0000:00:14.1: reg 18 io port: [0x00-0x07]
pci 0000:00:14.1: reg 1c io port: [0x00-0x03]
pci 0000:00:14.1: reg 20 io port: [0xf800-0xf80f]
pci 0000:01:00.0: reg 10 32bit mmio: [0xfa000000-0xfaffffff]
pci 0000:01:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio: [0xfb000000-0xfbffffff]
pci 0000:01:00.0: reg 24 io port: [0xef00-0xef7f]
pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
pci 0000:00:02.0: bridge io port: [0xe000-0xefff]
pci 0000:00:02.0: bridge 32bit mmio: [0xfa000000-0xfcffffff]
pci 0000:00:02.0: bridge 64bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:02:01.0: reg 10 io port: [0xdf00-0xdfff]
pci 0000:02:01.0: supports D1 D2
pci 0000:02:03.0: reg 10 io port: [0xde00-0xdeff]
pci 0000:02:03.0: reg 14 32bit mmio: [0xfdeff000-0xfdeff0ff]
pci 0000:02:03.0: reg 30 32bit mmio: [0x000000-0x00ffff]
pci 0000:02:03.0: supports D1 D2
pci 0000:02:03.0: PME# supported from D1 D2 D3hot D3cold
pci 0000:02:03.0: PME# disabled
pci 0000:02:04.0: reg 10 32bit mmio: [0xfdefe000-0xfdefe7ff]
pci 0000:02:04.0: reg 14 io port: [0xdd00-0xdd7f]
pci 0000:02:04.0: supports D2
pci 0000:02:04.0: PME# supported from D2 D3hot D3cold
pci 0000:02:04.0: PME# disabled
pci 0000:00:14.4: transparent bridge
pci 0000:00:14.4: bridge io port: [0xd000-0xdfff]
pci 0000:00:14.4: bridge 32bit mmio: [0xfde00000-0xfdefffff]
pci 0000:00:14.4: bridge 32bit mmio pref: [0xfdd00000-0xfddfffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 11)
ACPI: PCI Interrupt Link [LNKF] (IRQs *3 4 5 6 7 10 11)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled.
PCI: Using ACPI for IRQ routing
pci 0000:00:00.0: BAR 3: can't allocate resource
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:09: mem resource (0xf0000-0xf3fff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
pnp 00:09: mem resource (0xf4000-0xf7fff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
pnp 00:09: mem resource (0xf8000-0xfbfff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
pnp 00:09: mem resource (0xfc000-0xfffff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
pnp 00:09: mem resource (0x0-0x9ffff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
pnp 00:09: mem resource (0x100000-0x7feeffff) overlaps 0000:00:00.0 BAR 3 (0x0-0x1fffffff), disabling
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: ioport range 0x228-0x22f has been reserved
system 00:01: ioport range 0x40b-0x40b has been reserved
system 00:01: ioport range 0x4d6-0x4d6 has been reserved
system 00:01: ioport range 0xc00-0xc01 has been reserved
system 00:01: ioport range 0xc14-0xc14 has been reserved
system 00:01: ioport range 0xc50-0xc52 has been reserved
system 00:01: ioport range 0xc6c-0xc6d has been reserved
system 00:01: ioport range 0xc6f-0xc6f has been reserved
system 00:01: ioport range 0xcd4-0xcdf has been reserved
system 00:01: ioport range 0x4000-0x40fe has been reserved
system 00:01: ioport range 0x4210-0x4217 has been reserved
system 00:06: ioport range 0x4d0-0x4d1 has been reserved
system 00:06: ioport range 0x800-0x87f has been reserved
system 00:08: iomem range 0xe0000000-0xefffffff has been reserved
system 00:09: iomem range 0x7ff00000-0x7fffffff has been reserved
system 00:09: iomem range 0x7fef0000-0x7fefffff could not be reserved
system 00:09: iomem range 0xffff0000-0xffffffff has been reserved
system 00:09: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:09: iomem range 0xfff80000-0xfffeffff has been reserved
pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
pci 0000:00:02.0: IO window: 0xe000-0xefff
pci 0000:00:02.0: MEM window: 0xfa000000-0xfcffffff
pci 0000:00:02.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
pci 0000:00:14.4: PCI bridge, secondary bus 0000:02
pci 0000:00:14.4: IO window: 0xd000-0xdfff
pci 0000:00:14.4: MEM window: 0xfde00000-0xfdefffff
pci 0000:00:14.4: PREFETCH window: 0x000000fdd00000-0x000000fddfffff
pci 0000:00:02.0: setting latency timer to 64
bus: 00 index 0 io port: [0x00-0xffff]
bus: 00 index 1 mmio: [0x000000-0xffffffff]
bus: 01 index 0 io port: [0xe000-0xefff]
bus: 01 index 1 mmio: [0xfa000000-0xfcffffff]
bus: 01 index 2 mmio: [0xd0000000-0xdfffffff]
bus: 01 index 3 mmio: [0x0-0x0]
bus: 02 index 0 io port: [0xd000-0xdfff]
bus: 02 index 1 mmio: [0xfde00000-0xfdefffff]
bus: 02 index 2 mmio: [0xfdd00000-0xfddfffff]
bus: 02 index 3 io port: [0x00-0xffff]
bus: 02 index 4 mmio: [0x000000-0xffffffff]
NET: Registered protocol family 2
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs... done
Freeing initrd memory: 836k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1732
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:00.0: MSI quirk detected; MSI disabled
pci 0000:01:00.0: Boot video device
pcieport-driver 0000:00:02.0: setting latency timer to 64
pcieport-driver 0000:00:02.0: found MSI capability
pci_express 0000:00:02.0:pcie00: allocate port service
pci_express 0000:00:02.0:pcie01: allocate port service
pci_express 0000:00:02.0:pcie03: allocate port service
aer 0000:00:02.0:pcie01: AER service couldn't init device: no _OSC support
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
input: Macintosh mouse button emulation as /class/input/input0
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 332k freed
SCSI subsystem initialized
libata version 3.00 loaded.
pata_acpi 0000:00:12.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
pata_acpi 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
scsi0 : pata_atiixp
scsi1 : pata_atiixp
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf800 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf808 irq 15
ata2.00: ATAPI: HP DVD Writer 740b, ED24, max UDMA/33
ata2.00: configured for UDMA/33
scsi 1:0:0:0: CD-ROM HP DVD Writer 740b ED24 PQ: 0 ANSI: 5
sata_sil 0000:00:12.0: version 2.3
scsi2 : sata_sil
scsi3 : sata_sil
ata3: SATA max UDMA/100 mmio m512@0xfe02f000 tf 0xfe02f080 irq 22
ata4: SATA max UDMA/100 mmio m512@0xfe02f000 tf 0xfe02f0c0 irq 22
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: ATA-8: SAMSUNG HD501LJ, CR100-10, max UDMA7
ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/100
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: ATA-7: WDC WD2500JS-60MHB1, 10.02E01, max UDMA/100
ata4.00: 488397168 sectors, multi 16: LBA48
ata4.00: configured for UDMA/100
scsi 2:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5
scsi 3:0:0:0: Direct-Access ATA WDC WD2500JS-60M 10.0 PQ: 0 ANSI: 5
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:13.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.2: irq 19, io mem 0xfe02c000
Driver 'sd' needs updating - please use bus_type methods
sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:<6>ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:13.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 19, io mem 0xfe02e000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ohci_hcd 0000:00:13.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 19, io mem 0xfe02d000
sda1 sda2 sda3 sda4
sd 2:0:0:0: [sda] Attached SCSI disk
sd 3:0:0:0: [sdb] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 3:0:0:0: [sdb] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 3:0:0:0: [sdb] Attached SCSI disk
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
usb 1-7: new high speed USB device using ehci_hcd and address 5
usb 1-7: configuration #1 chosen from 1 choice
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, 242 bytes nvram
usb 2-2: new low speed USB device using ohci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice
8139too Fast Ethernet driver 0.9.28
8139too 0000:02:03.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
eth0: RealTek RTL8139 at 0xf8182000, 00:13:d3:88:fb:ec, IRQ 20
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
lirc_dev: IR Remote Control driver registered, major 61
lirc_mceusb2: Philips eHome USB IR Transceiver and Microsoft MCE 2005 Remote Control driver for LIRC $Revision: 1.44 $
lirc_mceusb2: Daniel Melander <[email protected]>, Martin Blatter <[email protected]>
usbcore: registered new interface driver lirc_mceusb2
usb 3-1: new full speed USB device using ohci_hcd and address 2
C-Media PCI 0000:02:01.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
usb 3-1: configuration #1 chosen from 1 choice
input: Power Button (FF) as /class/input/input1
usb 3-1: reset full speed USB device using ohci_hcd and address 2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input2
ACPI: Power Button (CM) [PWRB]
processor ACPI_CPU:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
processor ACPI_CPU:01: registered as cooling_device1
ACPI: Processor [CPU1] (supports 8 throttling states)
lirc_dev: lirc_register_plugin: sample_rate: 0
lirc_mceusb2[2]: Philips eHome Infrared Transceiver on usb3:2
usb 3-2: new low speed USB device using ohci_hcd and address 3
usb 3-2: configuration #1 chosen from 1 choice
usb 3-4: new full speed USB device using ohci_hcd and address 4
usb 3-4: configuration #1 chosen from 1 choice
Linux agpgart interface v0.103
usbcore: registered new interface driver hiddev
scsi 1:0:0:0: Attached scsi generic sg0 type 5
sd 2:0:0:0: Attached scsi generic sg1 type 0
sd 3:0:0:0: Attached scsi generic sg2 type 0
input: Logitech HID compliant keyboard as /class/input/input3
generic-usb 0003:046D:C30E.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech HID compliant keyboard] on usb-0000:00:13.0-2/input0
parport_pc 00:07: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
input: Logitech HID compliant keyboard as /class/input/input4
generic-usb 0003:046D:C30E.0002: input,hidraw1: USB HID v1.10 Device [Logitech HID compliant keyboard] on usb-0000:00:13.0-2/input1
input: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM) as /class/input/input5
generic-usb 0003:045E:0047.0003: input,hidraw2: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:13.1-2/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
nvidia: module license 'NVIDIA' taints kernel.
piix4_smbus 0000:00:14.0: SMBus Host Controller at 0x500, revision 0
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
input: PC Speaker as /class/input/input6
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
scsi5 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
ohci1394 0000:02:04.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[21] MMIO=[fdefe000-fdefe7ff] Max Packet=[2048] IR/IT contexts=[4/8]
Error: Driver 'pcspkr' is already registered, aborting...
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
nvidia 0000:01:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module 180.22 Tue Jan 6 09:29:08 PST 2009
EXT3 FS on sda2, internal journal
ReiserFS: sda3: found reiserfs format "3.6" with standard journal
ReiserFS: sda3: using ordered data mode
ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda3: checking transaction log (sda3)
ReiserFS: sda3: Using r5 hash to sort names
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0010dc0000bc42b8]
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
scsi 5:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
sd 5:0:0:0: [sdc] Attached SCSI removable disk
sd 5:0:0:0: Attached scsi generic sg3 type 0
scsi 5:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
scsi 4:0:0:0: Direct-Access ST316002 3A 8.01 PQ: 0 ANSI: 0
sd 5:0:0:1: [sdd] Attached SCSI removable disk
sd 5:0:0:1: Attached scsi generic sg4 type 0
scsi 5:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
sd 4:0:0:0: [sde] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
sd 4:0:0:0: [sde] Write Protect is off
sd 4:0:0:0: [sde] Mode Sense: 03 00 00 00
sd 4:0:0:0: [sde] Assuming drive cache: write through
sd 4:0:0:0: [sde] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
sd 4:0:0:0: [sde] Write Protect is off
sd 4:0:0:0: [sde] Mode Sense: 03 00 00 00
sd 4:0:0:0: [sde] Assuming drive cache: write through
sde: sde1
sd 4:0:0:0: [sde] Attached SCSI disk
sd 4:0:0:0: Attached scsi generic sg5 type 0
usb-storage: device scan complete
sd 5:0:0:2: [sdf] Attached SCSI removable disk
sd 5:0:0:2: Attached scsi generic sg6 type 0
scsi 5:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
sd 5:0:0:3: [sdg] Attached SCSI removable disk
sd 5:0:0:3: Attached scsi generic sg7 type 0
usb-storage: device scan complete
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present
kjournald starting. Commit interval 5 seconds
EXT3 FS on sde1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
TCP(wget:15427): Application bug, race in MSG_PEEK.
TCP(wget:18681): Application bug, race in MSG_PEEK.
TCP(wget:4122): Application bug, race in MSG_PEEK.
TCP(wget:4275): Application bug, race in MSG_PEEK.
TCP(wget:19451): Application bug, race in MSG_PEEK.

Inconsistent Airport USB disk mounting patterns

I have two Airport Extreme networks -- one at home and one in my office at work. I access both networks with a MacBook. Fine so far.
I also have an Iomega USB disk attached to the APE at home and an identical disk attached to my APE at work. The disk at home mounts nicely on my desktop. However, the disk at school does not mount. Connection proceeds to the point where I type in the password, but it does not mount, and I get the volume "__" could not be mounted message. This message appears regardless of which user account I work.
So, the Airport disk mounts fine at home but does not mount at my office. I've spent several hours deleting preference files, mucking around with the Airport Utility, etc. No go. Restarting the APE at work sometimes gives short-lived success, but it does not seem to last.
Any suggestions?

Okay, after reading several other discussion posts, the best workaround I've been able to find is to mount the Airport Disk through the Connect to Server menu. You'll need to know the IP address of your AirPort. It's probably either 10.0.1.1 or something like 192.168.0.1 -- you can find it by running AirPort Utility from the Utilities folder. Just click on your AirPort base station on the left side and the utility should say what the IP address of your base station is. (You can then quit AirPort Utility.)
Then press cmd-K, OR from the Finder click on the Go menu and then select Connect to Server...
In the "Server Address" box, type smb://AEBS-IP-adress/Volume-name
For example, in my setup, I connect to smb://10.0.1.1/Iomega because my AirPort Extreme Base Station has an IP address of 10.0.1.1 and the name of the drive I have connected to my AEBS is called "Iomega" The volume should now mount and show up in the Toolbar of any Finder window. It does NOT show up as a separate volume on my desktop, but your mileage may vary.
This has worked for me each time I've tried it and is much more reliable than trying to select my AEBS from the "Shared" option in the Toolbar of the Finder window.
BTW: If you will be doing this regularly, you may want to go back to the Connect to Server menu and click the + button to add it as one of your favorite servers.

Force Mount Point for USB disk drive

I need to force my 2TB usb drive to mount at the same mount point every time I log on or after I reboot the machine it seems to change - /Volumes/data, /Volumes/Data 1, ...
Can someone offer a solution?

Just to make sure I'm understanding this correctly....the iTunes library files (iTunes Library.itl and iTunes Music Library.xml) are currently located in my "My Documents\My Music\iTunes" folder. So, first I should delete the .xml file, right?
Then, you say to change my preferences and redirect iTunes to the new location of my songs (on the external USB drive). So, I would change the current setting of "C:\Documents and Settings\Jim\My Documents\My Music\iTunes\iTunes Music" to now point to the location of the new drive "I:\mp3" ?
What happens to the .itl file left behind in the old location? ...and all the directories with all my album art....I dont' want to lose that stuff.
Sorry, but I'm just a bit confused...well, a lot confused about where these files will be located. Before, my iTunes was configured with the iTunes music folder locations to be: "C:\Documents and Settings\Jim\My Documents\My Music\iTunes\iTunes Music" and all my mp3s were stored on the external USB disk drive....no music was in the iTunes Music folder. This config also put the library files in the \My Music\iTunes folder.
With making the changes you suggest will the library files and all the music now be on the external drive? The reason I ask is that I read some other posts from people that had everything on the external drive and if they had issues with their system connecting to the external drive, then iTunes would create a new library on the C drive and not let the user know.
Thanks for your patience in trying to explain this to me.

USB disks no longer mount, unknown filesystem

Ran a routine weekly update on an arch box this morning, didn't think anything of it as usual. Until Thunar started spitting errors at me whenever I tried to mount a USB device. gvfs makes the devices appear in the left pane for one-click mounting... usually.
A partition on the hard drive attached has started telling me I don't have permissions to mount it any more - never had issues before, I'm in storage so I don't see why.
The other issue comes with a USB hard drive, and when trying to mount it as above, Thunar throws this at me:
Error mounting /dev/sdb1 at /run/media/pip/HD-PVU2: Command-line `mount -t "vfat" -o "uhelper=udisks2,nodev,nosuid,uid=1000,gid-100,shortname=mixed,dmask=0077,utf8=1,showexec" "/dev/sdb1" "/run/media/pip/HD-PVU2"' exited with non-zero exit status 32: mount: unknown filesystem type 'vfat'
Searching both pacman and AUR gave me no packages to do with vfat filesystems, and the wiki article "USB Storage Devices" provided no solutions at all.
Using XFCE4 DE on 32-bit Arch. All packages have been updated to latest versions as of the time of this post.

I probably experience the same kind of problem as you guys. I'm using udisksvm to mount USB drives and when I plug one, I get something like that:
$ udisksvm
Automounting for non optical devices enabled
Added object : /org/freedesktop/UDisks2/drives/Intenso_Basic_10011100031138
Added object : /org/freedesktop/UDisks2/block_devices/sdb
Added object : /org/freedesktop/UDisks2/block_devices/sdb1
Automounting /dev/sdb1...
Mounting failed with error:
GDBus.Error:org.freedesktop.UDisks2.Error.NotAuthorizedCanObtain: Not authorized to perform operation
traydvm for /org/freedesktop/UDisks2/block_devices/sdb1 now running with pid : 2694
/usr/lib/python2.7/site-packages/gi/types.py:47: Warning: g_variant_unref: assertion `value->ref_count > 0' failed
return info.invoke(*args, **kwargs)
$ udisksvm
Automounting for non optical devices enabled
Added object : /org/freedesktop/UDisks2/drives/Nokia_S60_359557013658840
Added object : /org/freedesktop/UDisks2/block_devices/sdb
Added interface on object : /org/freedesktop/UDisks2/block_devices/sdb
Automounting /dev/sdb...
Mounting failed with error:
GDBus.Error:org.freedesktop.UDisks2.Error.NotAuthorizedCanObtain: Not authorized to perform operation
traydvm for /org/freedesktop/UDisks2/block_devices/sdb now running with pid : 3025
/usr/lib/python2.7/site-packages/gi/types.py:47: Warning: g_variant_unref: assertion `value->ref_count > 0' failed
return info.invoke(*args, **kwargs)
And the device is not mounted automatically. I have the packages dosfstools, ntfs-3g, systemd-sysvcompat installed (I use systemd). Mounting manually from console works well.

USB disk access of every type is hosed - HELP!?

Newbie with the very latest "Don't Panic" running on a laptop. I'm coming off a year with various bloateddistros, looking for something fast and stable.
I've got my internal drive up, networking, x, gnome and openoffice all working great. Next step is to plug in my external 160gig drive with all my data on it. This is a very standard USB2-to-EIDE drive, I've had no problems with it in any distro. It's split between a 32gig FAT32 partition and a 119gig Ext3.
I followed the wiki on autofs. Nothing. Then played with HAL and the like. Made my user a member of group "storage". Still nothing.
I've seen mount problems before of course, so I tried adding gparted via pacman and running that from a root command line just to see what's physically out there. Not good: gparted never finishes getting past the "Scanning all devices....." process with the blue bar bouncing back and forth. When gparted first starts I can hear the external disk spin up and chug for a few seconds, but then nothing.
I tried a 1gig USB flash critter (probably Fat32), nothing there either. I think something is fundamentally hosed in my USB disk support. I do have a USB external trackball working though...so my ports are up.
My daemons at present:
DAEMONS=(syslog-ng network netfs crond ntpd hal cups gdm alunnd)
Heeeelp! Neeeed my daaaata!
Wait, something else weird: if I turn on the external disk I see some CPU activity on my gnome panel monitor. Nothing major, a few light spikes. I've got a Celeron 1.6 but with the new 533 memory bus and 2gigs RAM. Once I run gparted it goes bananas and then once I close gparted CPU activity is pegged hard at 100% - yet there's no listed process eating that. Then when I turn off the external drive, CPU activity falls back to normal.
WTF, over?
Jim

Well before reading Veek's post I got further along. Almost there I think.
I went and loaded XFCE4 plus extras, and logged in with a XFCE session. I like having a backup desktop environment anyways in case Gnome gets squirrelly.
In XFCE Thunar shows the disks, but when I try and access 'em I get:
Failed to mount "128G Volume".
(exo-mount:4613): Gtk-WARNING **: Locale not supported by C library.
Using the fallback 'C' locale.
You are not privileged to mount the volume "128G Volume".
What I can't figure out is, what permissions? I'm added to groups "storage" and "disks"...any more needed?
The output from fdisk -l:
bash-3.2$ fdisk -l
Disk /dev/sda: 80.0 GB, 80026361856 bytes
255 heads, 63 sectors/track, 9729 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 * 1 9729 78148161 83 Linux
Disk /dev/sdb: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sdb1 1 19457 156288321 5 Extended
/dev/sdb5 1 3824 30716217 b W95 FAT32
/dev/sdb6 3825 19457 125572041 83 Linux
bash-3.2$
I'm going to jump back to Gnome and try Veek's concepts...

GNOME, nautilus, devicekit-disks: mount USB disk

Similar Messages

Maybe you are looking for