Going from an e series board to an s series board using traditional NI DAQ

I'm using the AI Acquire Waveforms.vi in LabVIEW with an E-series board (a 6040E), and I want to switch to an S-series board (a 6111). Is it possible to switch boards without making any changes to my LabVIEW 'program'? If it runs without any changes, will it sample simultaneously or sequentially?
Thanks.

Hello pdan,
So you can certainly use the same program for E and S Series devices (given that all the functionality is supported), due to the fact that they both use the NI-DAQ driver. As to your concern, the S Series device is most certainly acquiring data simultaneously. It is not possible for the S Series board to acquire sequentially. Hope this helps!
-Alan A.

Similar Messages

My iPod has recently begun to lose charge at a rapid rate, going from 100% to 10-15% in 24 hours, where it used to be above 60% in the same time and use.

As the title says, my 4th gen iTouch has recently (last few weeks) begun losing charge at a rapid rate. I charge it fully until I go to bed, wake up it's at 85%. After about 12 hours, with moderate usage (browse the web for roughly 2 hours of the time, a few IMs), and by then it is either at or below 20%. This issue has not been present long, but it's becoming increasingly frustrating. I used to use it to play Netflix overnight, leaving a movie or tv show playing, and it would use about 10% (depending on the length). It now loses 10% in sleep mode over the same time.
I have a few thoughts as to why, but no idea if they'd be correct. One is that we've recently had a lot of network issues, we had two routers going at one point, and one of them had a strong signal but never allowed access to the internet (weirdly) and the other worked normally. We have finally gotten rid of the problem router, but it was around the same time this issue began, so I was wondering if different wifi signals could require more work for the iPod? It sounds stupid to me, but it's one idea.
The second is that I have not synced to my computer in over 3 months. I recently built a new computer, and never got around to transferring my music files to the new computer. I know I've had numerous app updates, new downloads, deleted a few apps, and at least one software update. Do those files linger on the iPod until synced with a computer?
Before suggesting, I have turned off location services, notifications, Bluetooth, and my backlight has always been at about 20% of the slider.
I appreciate any and all help anyone can offer, thank you in advance.

First, try to reset the phone by holding the sleep and home button for about 10sec, until the Apple logo comes back again. You will not lose data by resetting. If the problem comes back, try to set it up as new device, explained here:
How to back up your data and set up as a new device
It might be necessary not to restore from the latest backup, in case it contains corrupt data causing the drain.
Deleting the mail account and setting it up again might also help if your account uses push service.
Sometimes switching iCloud off and on again also does the trick.

Going from 256GB to 80GB SSD

Hello,
I'm going from my 256GB to an 80GB SSD, and I'll use an external for my file store. When I restore using time machine, do I have the option to pick and choose what I want to restore?

Hi, and welcome to the forums.
That depends on what you want to do. You have 4 options:
Restore your entire system to the exact state it was in at the time of any backup. See #14 in the Frequently Asked Questions *User Tip,* also at the top of this forum.
Install OSX, then restore your settings, apps, users, and/or data via +Setup Assistant.+ See #19 in the FAQ Tip. Then download and install the "combo" update to get back to 10.5.8. Info and download available at: http://support.apple.com/downloads/MacOS_X_10_5_8_ComboUpdate Be sure to do a +Repair Permissions+ via Disk Utility (in your Applications/Utilities folder) afterwards.
Install OSX, set up one user and install the "combo" as above. Then use +Migration Assistant,+ per this Apple article: http://support.apple.com/kb/HT3322
Install OSX, set up one user and install the "combo" as above, then restore selected items from Time Machine. See #15 in the FAQ tip.
Without knowing just what you want to do, we can only advise that usually your best bet is to do the full system restore, then delete anything you don't want, rather than trying to pick and choose what you do want, especially with applications.

Hi When going from Develop module to print module a white boarder appears on screen which also prints via my epson r3000 printer. I can get round this by exporting photo to Elements and printing from there but can i get rid of the boarder and print from l

Hi When going from Develop module to print module a white boarder appears on screen which also prints via my epson r3000 printer. I can get round this by exporting photo to Elements and printing from there but can i get rid of the boarder and print from lightroom?

In the printer driver (accessed through the Page Setup button) set the Advanced tab to borderless. Then in the right hand panel under Layout set all the margins to zero.

My computer screen goes from grey to black on startup and stays there. Can any one help me?

Hi there,
I was wondering if anyone can tell me what is going on with my Mac Pro. The screen is blank or black. When I reboot, it goes from the grey startup screen to black and nothing after that. HELP.

You don't say which year it is, but if it's a 13" you're not having a common GPU that some 2010 and 2011 15" models are having.
Since reinstalling the OS didn't help, I'm afraid that the only real choice you have is to take the machine to your local Apple Store or an AASP and have them run diagnostics on the machine. It's likely a screen problem, rather than a logic board problem (although that's always a possibility).
The testing is free as if the estimate for repair. There's really nothing else you can do yourself at this point.
Sorry,
Clinton

Why does my screen goes from bright (normal) to dim?

I hope someone can help. My screen keeps going from bright (normal) to dim then back to normal .

It could be a short in your power adaptor cable, break or crack in the power jack that the power adaptor plugs into, a failing power inverter (small long thin circuit board in the screen that converts DC back to AC) or some unusual setting in the power setting for the laptop. I have no idea what that last one actual is but I am guessing. Look at the notebook and note which lights are on when it is bright. See if the external power light goes out when it goes dim. This happens when you go from plugged power to battery. Try to run the notebook with the battery out of the system for a day and see if you still have the problem. Maybe the battery is starting to short out.
Reminder: Please select the "Accept as Solution" button on the post that best answers your question. Also, you may click on the white star in the "Kudos" button for any helpful post to give that person a quick thanks. These feedback tools help keep our community active, so you receive better answers faster.

Outputting 2 channels from an AT-MIO board

i'm attempting to output 2 channels from an AT-MIO-16E-1 board using
labview. the first channel goes out fine but when i try to add the second
i get an error message and no second channel. the error mesage is:
Error -10687 occured at AO Buffer Write.
Possible reasons: A configuration change has invalidated the acquistion
buffer, or an acquisition buffer has not been configured.
does anyone know how to solve this problem?
thanks,
jon.

Thank you for contacting National Instruments.
When you write �instrument driver,� I understand you to mean one of the complete LabVIEW VIs often available for communicating with things like o-scopes and DMMs through serial or GPIB interfaces. These usually have front panels similar to the look of the actual instrument.
When it comes to DAQ products, there are no �instrument drivers� per se. Nonetheless, there are a variety of example programs available. From the first screen that you see when you load LabVIEW, choose the option to search examples. Then look under Data Acquisition. There will be examples available for whatever type of DAQ operation you wish to perform.
Regards,
Mike G.
National Instruments Support

Installed the update tonight and now my phone (Lumia 928) won't power up. I've tried a soft reset, but the screen goes from the Nokia logo to a red Verizon screen to a black screen. What's wrong and how do I fix it? Help!

Installed the update tonight and now my phone (Lumia 928) won't power up. I've tried a soft reset, but the screen goes from the Nokia logo to a red Verizon screen to a black screen. Tried it 10 times with the same result. What's wrong and how do I fix it? Help!

Oh no Mr.Ected!
I can see if we can get your phone back on! I understand how important it is to have a phone. Have you tried this to see if we can get it back on? http://vz.to/1DZhteH . If it is still goes to a red Verizon screen and then to black we might need to do a master reset. While the phone is off try this:http://vz.to/1DZhXkU Be mindful this is the last resort because it will erase everything on the phone. If you have done back up assistant in the past you will be able to get you contacts back. Please let me know if you need any more help.
AmberF_VZW
Follow us on Twitter @VZWSupport

Going from iphone 4s to 6 want to know if i can save and or tran my voicemails and voice memos to put on my new phone

going from 4s to 6 can I save my favorite voice mails and voice memos to put on my new phone via pc or cloud

If you are planning to set up your iPhone 6 by restoring the iCloud backup from the iPhone 4s, your Visual Voice Mails and Voice Memos will be restored.

IPhone 4s Voice Memo App has 5 second delay when the record button is pressed. When it starts recording, it goes from 0 seconds to 5 or so seconds recorded. This happens randomly and often and sometimes has the delay but starts at zero. Solution Anyone?

After iOS 7 update, my iPhone 4s Voice Memo App has 5 second delay when the record button is pressed. When it starts recording, it goes from 0 seconds to 5 or so seconds that it shows has recorded. This happens randomly and often, sometimes it will have the 5+ second delay but starts recording at zero seconds. Besides the delay it has been working fine as far as saving and playback is concerned. I have plenty of storage on the phone itself and it NEVER had this problem before I updated to iOS 7. I've reset the phone a couple times by holding down the power and home buttons at the same time. The reason I have an issue with this is that I'm always recording song ideas, melodies, and scratch takes; what I'm saying is when I come up with an idea I need to be able to know that when I hit record it will start right then so I don't forget anything that has just popped in my mind.
Does anyone have a solution or suggestion?
Thanks

After iOS 7 update, my iPhone 4s Voice Memo App has 5 second delay when the record button is pressed. When it starts recording, it goes from 0 seconds to 5 or so seconds that it shows has recorded. This happens randomly and often, sometimes it will have the 5+ second delay but starts recording at zero seconds. Besides the delay it has been working fine as far as saving and playback is concerned. I have plenty of storage on the phone itself and it NEVER had this problem before I updated to iOS 7. I've reset the phone a couple times by holding down the power and home buttons at the same time. The reason I have an issue with this is that I'm always recording song ideas, melodies, and scratch takes; what I'm saying is when I come up with an idea I need to be able to know that when I hit record it will start right then so I don't forget anything that has just popped in my mind.
Does anyone have a solution or suggestion?
Thanks

Data not going from active data table to new data table -DSO activation iss

Hi Experts,
Data is going from DSO1 to DSO2. I see some of the records are getting missed in DSO 2 which are supposed to come.
There is start routine from DSO1 TO DSO2 and as per the start routine some records should come but they are getting missed.
Apart from that..to DSO 2 there are 4 other DSO sending data.
I tried to send single record and saw that data is going

Hi Experts,
Data is going from DSO1 to DSO2. I see some of the records are getting missed in DSO 2 which are supposed to come.
There is start routine from DSO1 TO DSO2 and as per the start routine some records should come but they are getting missed.
Apart from that..to DSO 2 there are 4 other DSO sending data.
I tried to send single record and saw that data is going to New data table and upon activation it does not go to Active data table.
Please suggest.
Regards
Sudha

My ipod 5th gen ios 7.0.6 crashed and keeps going from the apple logo, going to a black screen, back to the apple logo, then back to the black screen and so on. Furthermore, my laptop doesn't recognise that the iPod is connected. What do I do?

My ipod 5th gen ios 7.0.6 crashed and keeps going from the apple logo, going to a black screen, back to the apple logo, then back to the black screen and so on. Furthermore, my laptop doesn't recognise that the iPod is connected. What do I do?
Please help me out as this is very irritating. This has been happening for the last 20-30 minutes. It had roughly half battery left.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Blue screen of death, and continous reboot. Phone never actually boots up, just keeps going from reboot to blue screen and back again. Any suggestion?

Blue screen of death, and continous reboot. Phone never actually boots up, just keeps going from reboot to blue screen and back again. Any suggestion?

Hello jared1915
If you are stuck in that loop, the next step would be to restore your iPhone. Check out the article below to get your iPhone into recovery-mode and restore it in iTunes.
If you can't update or restore your iOS device
http://support.apple.com/kb/HT1808
Regards,
-Norm G.

HT4623 The software update option is not on my phone. It just goes from "about" to "usage". I have an iPhone 3G. Every time I try to update it on iTunes, nothing changes. I have version 4.2.1, no matter what I do. Any suggestions?

I have an iPhone 3G, and cannot update my iOS. In the General tab, "Upadate Software" is not even there. It just goes from "About" to "Usage". When I try to update on iTunes, it always remains the same. iOS 4.2.1. Any suggestions? (My PC uses Windows XP). Also, my WiFi has completely quit working. Works fine on the other iPhones in the house, as well as the XBox 360, so I am sure it's my phone. I tried everything I could think of, including restoring the iphone to factory settings & then updating, but no luck. Thank you! for any help you can give! I plan to get an iPhone 5, but wasn't ready to do it quite yet. Hopefully my phone can be rescued until I'm ready.

That is the highest you will be able to go with 3g. You need 3gs or 4 to go any higher (multi processors and more memory needed). Version 4.2.1 marks the end of your updates for that device.

I had to get a new iphone and want to know how to tell if my pictures from my previous phone were backed up on itunes. when i connect my c even if i'm going from a 4 to a 5s?

i had to get a new iphone and want to know how to tell if my pictures from my previous phone were backed up on itunes. when i connect to itunes, does it automatically sync / backup even if i'm going from a 4 w/IOS 6 to a 5S w/IOS 7?

Welcome to the Apple Community.
Yes you can probably delete the 2 incomplete back ups they are unlikely to work.
However, I'd be inclined to back up to a computer as well and restore from there, if you are changing your phone.

Going from an e series board to an s series board using traditiona​l NI DAQ

Similar Messages

Maybe you are looking for

Going from an e series board to an s series board using traditional NI DAQ