Got a iMac upon start up it has white screen with apple logo and loading wheel spinning forever under it, does anybody know how to fix this?
PLEASE HELP!!!!!! EMERGENCY Upon start up normal start up noise occurs, then after white screen with Grey Apple logo, and a spinning loading wheel under it (thee repetitive lines NOT rainbow one) ?!? then thats as far as it goes it stays on that screen forever will not boot up. Any info on how to possibly fix? I've tried several of the Start up shortcuts , it wont even start up in Safe Mode . My fiance' is crushed she is a writer and EVERYTHING SHE HAS WORKED ON is somewhere on that hard drive. Any thoughts, i'm open to any and all LOGICAL responses, thank you very much for ya'lls time ........Its just heartbreaking to see my iMac in this vegistated coma,The whole reason i bought a mac was cause I love them I have Apple EVERYTHING, so once again please help.
Try this: Switch off your iMac wait 10-15 seconds hold down the Option Key (alt) key then press the power botton but keep the option key down. This should show all the available options to boot from. I trust you have a full backup, Good luck.
Similar Messages
-
Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help
Try the tips listed here Mac OS X: Gray screen appears during startup - Apple Support
-
imac wont boot - i get a white screen with apple logo, and it loads to about 10%, then screen goes black
Hey there mtriest,
It sounds like you are unable to boot the iMac successfully as it keeps shutting down when you try to boot. I suggest the troubleshooting from the following article named:
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/ts2570
Disconnect, test peripheral devices and network cables
Note: "Peripheral devices" refers to external devices other than what came with your Mac, such as hard drives, printers, or hubs that you connect via a USB or FireWire cable.
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Disconnect all peripheral devices such as external hard drives or printers (leave only the display, a keyboard, and mouse connected).
Disconnect any Ethernet cables.
Start up your Mac.
If you can start up this way, one or more of your peripheral devices (or installed software related to the device) is probably causing the gray screen issue. Connect one device, then restart your Mac to test for the issue. Repeat the process until you locate the device at issue. Make sure the device is powered if it needs to be to operate correctly. Check with the manufacturer of the device for support or possible software driver or firmware updates that may be available for the device. Try a different cable with the device if possible (such as a different USB or FireWire cable).
Note: If you have multiple peripheral devices and the issue only occurs when they are all connected, but not when each device is the only peripheral connected, see the Additional Information section below.
If you are using a desktop Mac with a third-party keyboard and/or mouse device, and the issue still occurs, try starting up with an Apple keyboard and mouse connected instead. Try starting with no keyboard and mouse connected, then connect them after start up. Also, try a different USB port on your Mac.
If the gray screen issue persists with no devices connected, go to the next section (with the peripherals still disconnected).
Perform a Safe BootSimply performing a Safe Boot may resolve this issue.
Shut down your Mac. If necessary, hold your Mac's power button for several seconds to force it to power down.
Start your Mac, then immediately hold the Shift key. This performs a Safe Boot. Advanced tip: If you want to see the status of a Safe Boot as it progresses, you can hold Shift-Command-V during start up (instead of just Shift).
Note: A Safe Boot takes longer than a typical start up because it includes a disk check and other operations.
If your Mac starts up as expected, immediately try restarting.
If the Safe Boot does not work, or the restart after a successful Safe Boot does not work, go to the next section.
There is additional information in the article with further troubleshooting if needed.
Thank you for using Apple Support Communities.
Cheers,
Sterling -
i bought iphone 5s 2 days ago and suddenly it turn off and start again till the white screen with apple logo and start again
please answer me as soon as possibleHello Ahmedabokamar,
Thanks for the question! I'd recommend taking a look at the following article for troubleshooting steps that can help get your iPhone working again.
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
Cheers,
Allen -
My Husband turned his desktop off without shutting down now When my desktop (Mac Power G5) starts up a folder comes up with 2 heads which changes to a question mark. Does anyone know how to fix this.?
Step 1- Try booting to Startup Manager by holding Option/Alt key.
Select the boot source and click the right arrow.
Once booted, open System Preferences and select the desired boot volume.
Replacing the PRAM battery is likely wise if the machine keeps forgetting it's boot source.
If that doesn't work,
Step 2- Boot holding a mouse click, insert the OS X install disc and hold C to boot to the install disc.
Once booted, open Disk Utility and "Repair Disk" on the boot drive.
Once done, reboot normally.
More:
http://support.apple.com/kb/TS1440 -
I have a iMac (20-inch, Mid 2009). On start up It will sit at the white screen with the logo and the wheel that spins under it. It will not go past this point? Any ideas?
Question (?) Mark, Blinking Folder, or Gray Screen at Startup
These are related but not identical issues. Their causes are outlined in Intel-based Mac- Startup sequence and error codes, symbols. Solutions may be found in:
A flashing question mark appears when you start your Mac
Mac OS X- Gray screen appears during startup
In most cases the problems may be caused by one or more of these:
a. Problem with the computer's PRAM - See Resetting your Mac's PRAM and NVRAM.
b. Boot drive's directory has been corrupted - Repair with Disk Utility.
c. Critical system files are damaged or deleted - Reinstall OS X.
d. The disk drive is physically non-functional - Replace the hard drive.
Note that the information I have provided is what Apple recommends, If other users suggest different solutions than found here, then be sure what they recommend does not impact on your warranty, if any, or ability to get continuing Apple service.
Please don't start removing drives or changing cables unless you know what you are doing and have exhausted other non-invasive alternatives outlined here. If you perform any work yourself that is unapproved by Apple, then you will void any warranty you may have and lose all further Apple Support.
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
The main difference if you are using Lion or Mountain Lion is that you must first boot from the Recovery HD. Simply boot from the Recovery HD to perform the above.
Reinstall Snow Leopard Without Erasing The drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
Reinstalling Lion/Mountain Lion Without Erasing The Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless. -
My dad has recently gotten a new phone and I got his old one. With his permission I restored it to factory settings and set up the iPhone 4 as a new phone with my apple id. Everything has downloaded fine but I have had many problems with my music. First it was where my phone didnt recognise my apple id, but I figured that out. Then it was where iTunes took one of my albums and split it so all the songs where their own albums. I fixed the album split on iTunes but its still like that on my iPhone. I have looked online everywhere and I still haven't found a solution! I'm getting super frustrated! Does anybody know how to fix this?
No it's not stealing. They have an allowance that you can share with so many computers/devices. You'll have to authorize her computer to play/use anything bought on your acct. You can do this under the Store menu at top when iTunes is open on her computer.
As far as getting it all on her computer....I think but I am not sure (because I don't use the feature) but I think if you turn on Home Sharing in iTunes it may copy the music to her computer. I don't know maybe it just streams it. If nothing else you can sign into your acct on her computer and download it all to her computer from the cloud. Not sure exactly how to go about that, I haven't had to do that yet. I wonder if once you authorize her computer and then set it up for automatic downloads (under Edit>Preferences>Store) if everything would download. Sorry I'm not much help on that. -
I get a white screen with apple logo and progress bar on my imac mavericks
I get a white screen with apple logo and progress bar ,then computer shuts down
when I turn my imac back on same thing happens,every time same thing
pprogress bar only goes half way then computer shut down
is there a solution ?
if not is there a way to at least salvage some files and docs?
i Have the latest imac 27Thanks I tried it but after I repaired my disk via disk utility at start up, it told me that
my disk can't be repaired and to try to back up my files so I can format it
but is there to back up my files?
also what I get is white screen with the progress bar not grey -
i upgraded to yosemite last week, now my computer wont start. it stops at white screen with apple logo. what do i do?
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
[Windows user] I have an ipod touch 5th generation 64gb and I can't backup my ipod. I have restored it many times, even in recovery mode, but it still comes up with "iTunes can't backup this ipod because the session has failed," yet it was still plugged in. Also error 54 pops up too. Does anybody know how to fix this?
If a PC try:
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
or
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8 -
my i phone 5c wont stop restarting!! sometimes it takes hours before the phone starts working again. Sometimes when it does this red lines go up and down the screen. Im so ready to go back to my 4s does anyone know how to fix this??? Should i mention i have tried restarting back to new and i have the most up to date software. Please help
If the center portion of the monitor is flickering then your GPU on the logic is bad or (unlikely given this symptom) that your monitor cable is pinched/damaged.
**Imediately backup ALL your important data while you can still see things on the monitor
Contact Apple for appt. for in shop diagnostics for full examination and for parts replacement
nobody can give you a cost on a repair that isnt fully diagnosed online and cannot be.
perform SMC reset just to check:
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer. -
MacBook will not start. I have restarted with original CD. I have used Utilities and "no problem" with hard drive. I have reset PRAM. I have tried safe boot. Nothing is work. Gray screen with Apple logo and rotating wheel. Thanks for any suggestions!
Snow Leopard is a Mac OS X version. You say that it's the version you have in your Mac (10.6.8). Do a back up of your files, format the hard drive (using Disk Utility) and reinstall again
-
Okay, so I got the latest update and apparently it doesn't work. I had an icon on my desktop that wouldn't open because the 'newer Itunes' is apparently corrupt or something. Going into my applications, I found another Itunes icon and it opens up, but not the F7, F8 and F9 keys aren't working with it. I've already tried installing the latest version and that hasn't helped. Does anyone know how to fix this problem?
Hey skyshade13,
Thanks for the question. The following article outlines how to restore a previous iTunes library should there be no content after updating. While the article does not speak specifically to your symptoms, attempting the steps by utilizing the "Previous iTunes Libraries" folder may resolve your issue.
No content shows up in iTunes after updating
http://support.apple.com/kb/TS1967
For further information see the following information:
OS X Lion: iTunes opens to "created by a newer version" alert
http://support.apple.com/kb/TS3918
iTunes: How to re-create your iTunes library and playlists
http://support.apple.com/kb/HT1451
Thanks,
Matt M. -
Imac does not start white screen with apple logo.......
Hi guys, my brand new Imac 21.5 got stuck on the white screen with apple logo and nonstop little wheel, but it never gets out of it....Disconnected everything else restarted but still nothing...stuck at the same screen. Please i need help, the machine is only 3 months old!!!
Hi, do you have AppleCare?
Call AppleHelp in any event 1-800-275-2273
You could try booting from your discs (Disc#1) that came with your Mac -
...L -
When i start my mac and i got white screen with apple logo
when i start my mac and i got white screen with apple logo n spening round n round
Try here
https://discussions.apple.com/thread/4917686?start=0&tstart=0
Maybe you are looking for
-
Restore needed but wont restore HELP PLEASE
my iphone keeps saying restore needed, iphone can not make calls or recieve calls restore on itunes phone says no service all the time, but iphone will not restore on itunes loads half way then stops, ive even tryed to restore settings on my phone ma
-
[Oracle 8i] Need help with bind variable in add_months function
I'm trying to put a variable within my add_months function: AND t1.edatetime >= add_months(sysdate,:v1) AND t1.edatetime <= add_months(sysdate,:v2)I have tried defining the variable both as 'integer' type and 'numeric' type, but in both cases
-
[svn] 2530: Fix incorrect drawing of line, when xFrom and yFrom are non-zero
Revision: 2530 Author: [email protected] Date: 2008-07-18 15:44:40 -0700 (Fri, 18 Jul 2008) Log Message: Fix incorrect drawing of line, when xFrom and yFrom are non-zero Reviewed by Ryan Modified Paths: flex/sdk/trunk/frameworks/projects/flex4/src/fl
-
ADF Faces & BC: Programmatic selection of row within a selectonechoice
OK i did some printouts and it looks like its occuring on this line: diseaseDescriptionLOVVo.findByKey(new Key(keyValues), -1); Is there a better way to do this selection?
-
Aperture crashes every time I look at keywords - any help?
I am considering upgrading to Aperture. I just loaded up the 30-day trial and imported about 500 images from my iPhoto library. Every time I hit the keywords button and then try to expand any of the lists, Aperture immediately quits. (And then help