Got grey screen and Apple Logo but wont start up

Out of the blue; my 2008 (1.8Mhz) Mac mini wont boot up and it just stop after showing a grey screen with white Apple logo on it.
I insert the DVD and ran Apple hardware Testing; strangly the machine passed all the hardware test. I did changed the logic board battery but still no luck! Can anyone help me to resolve this issue please?

Mac OS X: Gray screen appears during startup

Similar Messages

HT1199 my computer displays grey screen and apple logo for 10 minutes or more during start up and shut down. sometimes it refuses to shut down . this issues started after installing OS lion. what do i do?

my computer displays grey screen and apple logo for 10 minutes or more during start up and shut down. sometimes it refuses to shut down . this issues started after installing OS lion. what do i do?

I don't think it's exactly an incomplete installation brody, but most likely in-correct permissions somewhere along the line that either happened, or became magnified during the upgrade. Also, it could be corruption as well.
First thing to do, is boot up holding down Shift key to do a safe-boot so we an clean up any corrupted OS caches, after that do another reboot, but go to the Lion recovery, and scan the HD for errors, repair any if you find them, and then try to do a Repair Permissions job.
That should fix the issue, if not, we can start doing a PRAM reset and SMC for good measure.

My Imac won't go past the grey screen and apple logo! How do I fix the start up in my Imac?

I really need help with this one!
My Imac is stuck on the grey screen with the apple Logo, and it wont go past that.
It does listen to certain keyboard commands to start it up (ive tried fixing it by reading other's posts.) But it will only listen to some commands,
It doesn't start on Shift (safe mode) but it does start on command+shift+(other button) which is safemode viewed so you can see whats going on.
As the letters on the screen type on, it says it's loading something but stays stuck there.
I've heard about a way where you can use terminal from another computer and boot it that way, or using firewire cables.
Please help! and take in mind I'm not really tech-savy with computers, so guides would be helpful!
If there is any way to save the files in the computer that would be great. If it can't be done, it's fine, I just want it working again .
Thanks,
Gian Varela

I really need help with this one!
My Imac is stuck on the grey screen with the apple Logo, and it wont go past that.
It does listen to certain keyboard commands to start it up (ive tried fixing it by reading other's posts.) But it will only listen to some commands,
It doesn't start on Shift (safe mode) but it does start on command+shift+(other button) which is safemode viewed so you can see whats going on.
As the letters on the screen type on, it says it's loading something but stays stuck there.
I've heard about a way where you can use terminal from another computer and boot it that way, or using firewire cables.
Please help! and take in mind I'm not really tech-savy with computers, so guides would be helpful!
If there is any way to save the files in the computer that would be great. If it can't be done, it's fine, I just want it working again .
Thanks,
Gian Varela

2nd ATV displays black screen and apple logo on initial start up

I just hooked up my 2nd ATV and all I am getting is a black screen with the apple logo. I am using component video and composite audio. No HDMI hooked up. 1st ATV is unplugged. Also have network cable plugged in for now. Using timecapsule for wireless network. This is a second hand ATV, so it has been previously used and configured. I also attempted to hook up using an HDMI, but same result. I am not sure if the unit is trying to find the previous users network or not. The amber light flashes indicating start up. Nothing else on the screen, no question mark, rotating circle, just the logo. Every few minutes the screen goes blue (assuming it is my TV default colour) and then returns to the black screen and logo. I am on the correct TV input. Also tried, menu + '+' and menu + - on the remote for factory restore and screen settings.

melbri wrote:
I hope you are reffering to the possibility that the person I purchased the unit from may be a thief. I am working with him at the moment and building up to getting my cash back so he can deal with Apple. Thanks.
Sorry if my comments were misunderstood, I wasn't suggesting anyone was a thief, I was suggesting that without a receipt the store couldn't/shouldn't rely on the serial number to exchange/refund the tv, as proof of purchase.

I tried to upate the softwear but now when i go to turn it on it comes with with the gray screen and apple logo but with a bunch of letters and numbers at the top of the screen not letting me log on

I tried ot update the softwear and i clicked accept and it went grey while it said updating items. Once it finished after about 2 minutes it said restart so i pressed restart and the screen whent black, when i went to turn it on again the grey apple screen came up but with all these words and letters in the top let corner. In the middle and top of the screen mixed in with the rest of the letters it says unable to find driver for this platform

Hello CathBuck,
Welcome to the Apple Support Communities! I understand that you are experiencing issues with your MacBook Air. Based on the information you have provided, it sounds like the steps in the following resource may help to resolve your issue:
Mac OS X: Gray screen appears during startup - Apple Support
http://support.apple.com/en-us/TS2570
Thanks,
Matt M.

My macbook pro 2011 shows grey screen with apple logo and want start

i was just using my macbook pro and it freezed for a while not responding and i turned it off by pressing the power button. afterwards, i turn it on and it shows a grey screen with apple logo but want start pls somebody help me because am having "my life" on the machine

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode.* The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
*Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
A dead logic-board battery in a Mac Pro can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

My iMac wont go past the grey screen with Apple Logo and question mark a caution mark

My iMac wont go past the grey screen with Apple Logo and question mark a caution mark

You may find this support article helpful:
http://support.apple.com/kb/TS2570
Ciao.

I just opened my imac, i got the grey screen without apple logo, I just opened my imac, i got the grey screen without apple logo

I just opened my imac, i got the grey screen without apple logo, I just opened my imac, i got the grey screen without apple logo

I am curious as to why you repeated your question twice both in the subject box and in the discussion box?
In answer to your question, have you tried using
Disk Utility?
   1. Insert the Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
   2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
      Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
   3. Click the First Aid tab.
   4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
   5. Select your Mac OS X volume.
   6. Click Repair. Disk Utility checks and repairs the disk.
Then, if you can, reboot to your internal drive and repair permissions.

I have snow leopard installed as an OS. When trying to reboot a MacBook Pro I am getting stuck on grey screen with apple logo and rotating symbol. What can I do?

I have snow leopard installed as an OS. When trying to reboot a MacBook Pro I am getting stuck on grey screen with apple logo and rotating symbol. What can I do?

Maybe this might help.
http://support.apple.com/kb/TS2570

When i start my mac and i got white screen with apple logo

when i start my mac and i got white screen with apple logo n spening round n round

Try here
https://discussions.apple.com/thread/4917686?start=0&tstart=0

Macbook Pro (2011) froze while working, forced shut down, now won't turn on. Grey screen with apple logo and spinning wheel for hours. Help?

Macbook Pro (2011) froze while working, forced shut down, now won't turn on. Grey screen with apple logo and spinning wheel for hours. Help?
Unfortunately do not know the operating system since I never updated anything and I can't get in to it.
Thanks for your assistance.

If you want to preserve the data on the boot drive, and it's not already backed up, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data, you can skip this step.
There are several ways to back up a Mac that is not fully functional. You need an external hard drive to hold the backup data.
1. Boot from the Recovery partition or from a local Time Machine backup volume (option key at startup.) Launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
2. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
3. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.

Start up screen stuck on grey screen with apple logo and spinning gear

Start up screen is stuck on grey screen with apple logo and spinning gear. What should I do?

See this thread with dominic23’s suggestions: https://discussions.apple.com/thread/5783326?tstart=0

Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help

Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help

Try the tips listed here Mac OS X: Gray screen appears during startup - Apple Support

HT204347 Hi my serial number on bottom of my mac is W8*******66E when l try to try the computer on it is just going to grey screen with apple logo and spinning wheel i have tried starting in safe mode and a few other suggested solutions and they have not

Hi my serial number on bottom of my mac is W8******66E when l try to turn the computer on it is just going to grey screen with apple logo and spinning wheel i have tried starting in safe mode and a few other suggested solutions and they have not worked?
<Edited by Host>

What other solutions have you tried?
This may help you:
https://discussions.apple.com/docs/DOC-3353
Ciao.

Computer won't start, grey screen with Apple logo only. Ideas?

Last night my wife's G5 froze. It is a G5 2.0 running OS X 10.4.11. I shut it down (had to use the power button) and tried to restart. No luck, just made it to the grey screen with Apple logo and spinning wheel. After a few seconds the Apple logo disappeared and a black box took its place, then the wheel stopped spinning. It was late, decided top wait until morning before trying again.
This morning I tried to start up again. This time got a warning(?) in upper left that a Firmtek item had already started. I'm sorry I didn't write this all down at the time, so I don't remember the entire message. Since there is a Firmtek card installed in one of the PCI slots I thought that might be the problem, and I pulled the card, as well as another Adaptec card that was also installed. Tried to start again, got to grey screen with Apple but this time no spinning wheel.
Opened media slot manually and inserted Diskwarrior. Tried to start with Diskwarrior but again only reached grey screen. Let run for ~5 minutes, until fans started to run and were begining to get noisy.
Next I reset the PRAM. No luck, still stuck on grey screen. Tried Diskwarrior again, this time got another message in upper left. Here is most of it -
System Failure : cpu=1; code=60000009 (Invalid pmap)
Lateset crash info for cpu1;
Exception state (sv=0x609bb280)
PC=0x000a4ad0; MSR=0x02003000 followed by more similar strings, then
backtrace terminated - unaligned frame address; 0xfc088891
So what's the diagnosis? I've had various issues with my G5s in the past, but have never had one refuse to boot with Diskwarrior before.
Thanks in advance for any help!

Whew, could be many things, from RAM, (or RAM slots/solder issue), to CPU #1 being bad, (CPU#1 is actually the second one.
Does it boot into any of these modes?
Target mode...
http://support.apple.com/kb/HT1661
Does it boot to Single User Mode, CMD+s keys at bootup, if so try...
/sbin/fsck -fy
Repeat until it shows no errors fixed.
(Space between fsck AND -fy important).
Resolve startup issues and perform disk maintenance with Disk Utility and fsck...
http://docs.info.apple.com/article.html?artnum=106214
We might get clues with verbose mode...
http://support.apple.com/kb/HT1492

Got grey screen and Apple Logo but wont start up

Similar Messages

Maybe you are looking for