Goup result recording for inspection lots

Dear All,
Is there an option of recording results simultaneously for a number of inspection lots????
Please help out....
Regards ,
rishabh

Dear!!
Please Check QE51n with Plant as selection And unchecke With out usage decision below and execute ull get all the Inspection Lots
with regards
Pushpalas

Similar Messages

Result Recording for inprocess lot

Hello SAP gurus.
For in process inspection lot i have 3 operation for testing my requirment is if i goning for result recording for second operation without result recording for first operation system should restrict me. we are using 100 inspection point for inprocess inspection please suggest how can we do this?
Regards.

Dear,
Goto OPK4 -Select order type /Plant - Select 'Generally valid setting' for 'Operation sequence-Select 'Error when operation sequnce is not adhered and also QM Error message if no inspection result exists.
Or you can use the exit CONFPP05 PP order conf.: Customer specific enhancements when saving .
Regards,
R.Brahmankar

CRTD CHCR SPRQ-how to do result recording for that lot.

Hi All,
i am having issue.
i did GRN,lot is created with this status-CRTD CHCR SPRQ
i tried for Result recording but error is showing.
Then came to know QP01 is not assigned for that material.
then i created the QP01,but still i am not able to to Result Recording to that Lot.
is any way to do that.without cancell the lot can we do.
Regards,
siddharth shanker

Hi,
Your lot is at created status so you need to relesed lot. May be insection plan /task list has not been assigned to lot.
In Qa32 go in inspection lot Change ( Or T code -QA02 ) .where in tab Inspection specification tab click on task list/speci where you can assign plan theri ( You can assign plan with usage that you have created plan )
Save transaction.
refresh QA32 then try result.
Regards
SANIL
See QP02 with what usage you have cretaed plan.
as earlier I told you in QA02 tasl inspec tab in usage field select same usage by which you have created inspection plan.in QP01.
Regars
SANIL
Edited by: Sanil Vadke on Mar 29, 2010 8:40 AM

Result recording for 10th lot for specific MIC

Hello SAP Gurus,
Our requirment is we want to record result for one MIC for every 10th lot E.g 10th 20th 30th lot etc like this how can we do this?
Please suggest.
Regards,

Hi
Create DMR in QDR1, for usage decison. Make two stages, like stage 10 normal inspection and stage 20 skip. Mark stage one as initial and 20 as skip.
For stahge change of 10: No. of inspection lot 1, and new inspection change 20. For stage change of 20: no of lots 9 and new stage 10. For both stages 10 and 20, rejection will b 1 and new stage for that will be 10.
In inspection plan header data, there is a section for DMR level. Select DMR at characteristic level there.
So when you create lot: 1st lot will be be inspected, next 9 lots will be skipped. 11th will be inspected, next 9 lots will be skipped,...
Hope you will be able to do this, otherwise please revert back.

Automatic Results Recording for Inspection Plan

I'm trying to activate automatic results recording, at the beginning I get this meassage: "In customizing for default value of inspection type(400) you have to activate the following check boxes, " check characteristics", "Inspection with task list" & "Automatic assignment", I've done that. Yet, it sill doesn't work and the lot status is "CRTD" however it should be updated to "REL" status.

Hi,
Did you search enough before posting this query? There is plenty of discussions over this matter.
Based on the details given above, I don't think you have created an inspection plan.
Automatic assignment will assign the task list automatically to the inspection lot once it is created. You didn't mention if you have created one or not. Pl check that.
If the inspection plan is created, there could be possibility that material is assigned to more than one task list (inspection plan). If that is the case, you wouldn't get inspection lots with REL status but CRTD only.
ntn

Multiple results recording for Delivery inspection lot

Hi Gurus,
My requirement is to configure for quality results recording for sales delivery document. Where client wants to record Customer, supplier, Umpire, etc results record for inspection characteristics.
I got response from few Sapiens that I should use Inspection point concept for multiple results recording. Could anyone cna tell me how can I do this.
Your help will be highly appreciated.
Thanks,
Kumar

Hi Kumar,
Okay!
First of all letu2019s try to understand whether inspection points are really suitable for your requirement or not. Accordingly further errors can be eliminated. I just try to understand.
A- Using Inspection Points
1.     Inspection points are used when you inspect the same parameters again and again.
2.     When you click on results tab in QA32, system asks you put some identification number. Letu2019s say you put A1 and then press enter. Thereafter you record the actual results (LENGTH, WIDTH etc.) You save this without giving UD.
3.     For the next time when you again click on results for the same inspection lot, system again asks you to put identification number. This time suppose you put A2. Then again you record the results (LENGTH, WIDTH) for A2.
4.     Likewise you can retrieve the inspection results from system with respect to inspection point (identification point).
5.     Typically this can be used for chemical industries where you record the temperature of the same chemical after every ½ an hour. Here 10:00 am, 10:30 am can be used as identifications numbers. As a result of which you can get the information that at 10:00 am temperature was 40 Deg and at 10:30 am it was 75 degree Celsius.
If your requirement resembles this situation, then only the use of inspection points would be fruitful.
B- Without Inspection Points
But if you want to record the readings by various agencies like customer, umpire (refer following pattern)and want to compare them there are other ways.
1.     Reading by your inspector
a.     LENGTH u2013 100, 101, 102mm (average is 101mm)
b.     WIDTH     - 10.50, 10.50, 10.60mm (average is 31.6mm)
2.     Reading by customer
a.     LENGTH u2013 100, 101, 102mm (average is 101mm)
b.     WIDTH     - 10.50, 10.50, 10.60mm (average is 31.6mm)
3.     Reading by umpire
a.     LENGTH u2013 100, 101, 102mm (average is 101mm)
b.     WIDTH     - 10.50, 10.50, 10.60mm (average is 31.6mm)
You can achieve this without using inspection points also. For this in QP02 you need to create 3 operation; Inspector, Customer and umpire respectively. Feed the MICs in each of these operations. When you click on result tab system will throw pop up for these 3 operations. Double click on Umpire if you want to record results noted by umpire. Likewise for rest of the operations. You can do this even after UD also (after 1-2 months also). You need to use MIC with control indicator as long term characteristics for this in QS23.
Regarding averaging of results u2013 This can be achieved using single result recording MIC with or without inspection points. Use appropriate sampling procedure. When you feed results in QA32 system automaticaaly averages out the reading. This can be viewable against phi symbol.
Finally you did mention that u201Chere I am not getting the newly created inspection lotsu201D. Does that mean inspection lot (10 origin) has not created?
Regards,
Anand Rao

Three Physical Samples withdraw from inspection lot 04 and then result record for all three

Dear Gurus,
We have 3 quality labs and each lab is sent a separate samples to inspect certain characteristics once we receive material from production. I have created an inspection plan and mapped these three labs as work center in operation and then assigned MICs under each operation to inspect.
Now my issue is how to map separate 3 samples to inspection lot generated from production ( type-4) and also how to configure that to inspection plan.
I have to result record for all these three physical sample as withdrawn from Lot based upon inspection plan as mentioned above.
I can mention sample drawing procedure in inspection plan but how to map actual sample there.
Any help will be greatly appreciated.
Regards,
Satish

Hi Satish
You are creating three operation for depicting three testing Labs.
Against each lab (operation) you had assigned MICs as per your requirement.
Now you have to assign a SDP along with inspection point type 200 for physical sample in task list.
After prod confirmation system will create inspection lot along with a sample by default for 1st operation.
For other operations you have to create samples manually referring the same inspection lot (QPR6).Remember to click ' Create Insp points' and mention operation.
Release the samples in QPR4.
Now when you go for result recording system would ask first for operation, so select the operation , then system will ask for insp point (sample no).There click on assign insp point , so system will provide the Sample no which were created in QPR6 for that particular operation.
Please follow the steps and revert.
Regards
D Mohanty

Result recording for quantitative inspection characteristic

Team
Greetings!
Please find the following requirement.
We are using quantitative characteristics inspection.
Inspection lots are created automatically and the sample size for each characteristics are determined based on the sampling proceedure.
when we do result recording for a characteristic, say the sample size is 5, even if any one of the sample does not fall under the limit, we need the characteristic to be rejected.
How can this be addressed.
Gobinathan G

.

Sample results to one inspection lot

Hi,
Please confirm if the following is possible:
Record result for samples say 5 samples by today and then assign those sample result to one inspection lots after one week.
It yes then how ?
Regards

Hi Sun
First we need inspection lots to enter the results. If you mean five inspection lots results want to enter in one inspection lot. As per my knowledge it is not possible for transferring multiple result values to one inspection lot.
If you want to transfer one inspection lot to another please go through below link.
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/60221c69-0f8b-2b10-eebf-bec51a601dd6?QuickLink=index&…
Regards
Kesava

Result Recording of Inspection Characterstics.

Hi Gurus,
Actually we have one scenario in QA in which for one material there are certain specification whose result we will come to know few days later after posting inspection lot in Unrestricted & also after doing UD.
I want to know how to do result recording for that perticular specification after we already did the UD for that lot?
Is it possible after UD?
Is there any additional customization setting nedded?
Thanks in advance.

Hi,
You can do this .
Those MIC for which you want to take result after UD .In control indicator of MIC put long term inspection check box on .
So that even after UD of inspection lot , result record for that MIC will remain open for you to take result.
Regards
SANIL
Edited by: Sanil Vadke on Jun 29, 2010 8:53 AM

Recording against inspection lot

Hi Gurus,
We have one non valuated material. For this material we have prepared manual inspection lot and we assigned inspection point to it. Work center & shift are maintained as inspection point identifier. how many times we can record results against this inspection lot. is it fixed that we can do fix number of recording against this lot or we can record n number of results against this single lot.pls. help
Regards
Amit

Hi Amit
You can record N number of result against one inspection lot. Purpose of inspection point is to update results as per interval for larg time spam to eneble sufficient history for analysis purpose
Regards
Atul

SAP QM Result recording - Copy inspection results functionality

Dear all,
I have two queries.
1) The Raw materials used in various plants are same. I want to copy the inspection results to the inspection lot if the batch is already accepted in other plant. The material, batch and vendor is common point. Some of the characteristics are caluculated characteristics. How to map this requirement.
2) I want to test the standard functionality for copy results but in my system, the settings for copy inspection results is not appearing in quality inspections in SPRO. I want to confirm whether I am missing some other setting.
Regards,
Manohar

Hello Jessica,
you could try the following bapis:
BAPI_INSPCHAR_GETRESULT
BAPI_INSPCHAR_SETRESULT
Although the desired functionality was actually implemented in higher releases.
Hope this helps you.
Regards,
Isabelle

Bapi or FM to read data for inspection lot

Hi Experts
I need bapi or FM that will read all specifications and result value for entered inspection lot
the data that we also got in transaction qa13
I need exactly that data
Thanks
Taran

hI,
Check the below bapi's
GetDetail : Load detail data for inspection lot [ BAPI_INSPLOT_GETDETAIL ]
GetList : Select inspection lots [ BAPI_INSPLOT_GETLIST ]
GetOperations : Select inspection operations for inspection lots [ BAPI_INSPLOT_GETOPERATIONS ]
SetUsageDecision : Make automatic usage decision [ BAPI_INSPLOT_SETUSAGEDECISION ]
StatInterface : QM-STI Interface [ BAPI_INSPLOT_STATINTERFACE ]
Reward if helpful.
Regards,
nagaraj

Certificate creation for inspection lot

Dear all,
Is it possible to create test certificate for inspection lot of type 04. what is procedure to create this test certificate.
Thanx & regards,
Harish Parab.

Hi Harish,
You can generate an inspection certificate for the inspection lot generated for 04 insp type.
U need to use QC21 Certficate for inspection lot transaction ( U can search the lot for ur production order)
Basic steps to be done
1. Create certificate profile
2. Assign profile with out any recipient.
3. Generate certificate
Regards
Venugopal

Copying of Inspection results to another inspection lot automatically

Dear Guru
I need the results in the inspection lots to get copied to another inspection lot automatically.
Kindly let me knwo if u can do that and what are the possbilities.
thanks
Nithi A

This is standard SAP functionality. Please reveiw the help files:
http://help.sap.com/erp2005_ehp_01/helpdata/en/00/07cf2ec3b42046aeeb527773165efc/frameset.htm
Craig

Goup result recording for inspection lots

Similar Messages

Maybe you are looking for