GPIB analyzer error

I am a new user to Labview 7 Express. While running the GPIB analyzer for the instruments scanned I get an error titled MISSING CARD ERROR: Supported GPIB+ interface not found.......It also list some steps to troubleshoot but they does not work in my case (Installing the GPIB+ interface, Scan for hardare changes or enabling the interface. I am attaching a screenshot of the error in jpeg format. Also, when I view the properties of my GPIB-USB-B, I do not get the resources tab (only General and Driver tabs are seen). What do I need to do to remve the error. Thanks in advance.
Attachments:
GPIB_Analyzer_error.jpg ‏65 KB

Hello,
The first thing I wanted to verify with you is what GPIB board you have. You will only be able to use the GPIB Analyzer with a GPIB+ board. These boards can be found at the following link.
http://sine.ni.com/apps/we/nioc.vp?cid=12461〈=US
Also, if you do have one of these interfaces, then I need to request more information, such as the driver version and OS you are using. Also, are able to communicate with your instrument successfully in MAX?
Hope this helps!
Regards,
Steven B.
Applications Engineering
National Instruments

Similar Messages

GPIB Analyzer missing card error but troble wizard OK

In trying to install and communicate with my PCMCIA GPIB card the GPIB analyzer does not recognize the card (Unkown/missing GPIB+ Card). But all the installation wizards and troubleshooting wizards test satisfactory. I have reinstalled the device. Th OS recognizes the device but when I try to communicate with an instrument (connected and powered on) no instrument is detected. I then open the GPIB Analyzer and get the Card error. I am using a Gateway laptop with EWindows XP and a Centrino Processor.

Kent,
Does the "Scan for Instruments" button in Measurement and Automation explorer pick up the instrument and show it under the GPIB interface card? If so, then your instrument is responding properly to the GPIB signaling. One thing to remember when communicating with instruments is that not all instruments use the same types of commands, termination characters, or termination methods. Not all instruments will respond to "*IDN?" which is the default string in the 488.2 communicator. If you have the programmer's reference manual to the device, you should be able to determine what strings are appropriate to communicate with the device.
If your instrument is not showing up after a "Scan for Instruments", you need to check to make sure that the
re is not an address conflict between your card (usually address 0) and your device. Additionally, some low-level troubleshooting steps can be accomplished with IBIC. This link will help you use it.
Hope this helps,
Scott

Bank Analyzer - Error while creating the Position Structure

Hi,
We are implementing Bank Analyzer 6.0 and Implementing Financial Instrument and Financial Transaction.
We facing an Error while creating the Position Structure,
Error Message: Status of structure S40CURRACC is "New"
Anyone has an idea how to fix this?
Thank you,
John Crawford

Hi,
1.Run Transaction - /BA1/F0_SGS_START
2.Entered the name of the structure and try to "activate".
3.It will get Active without any inconsistency.
Regards
Phani

BEx Web Analyzer error message

Hi,
I've integrated BI 7.0 with Portal 7.0. Both systems (BI and Portal) running on different servers, SSO is configured both ways and RFC communication is configured from ABAP to J2EE. However when i run the BEx Web Analyzer iView under the Business Intelligence role, i get the following error:-
The initial exception that caused the request to fail, was:
     No logical system exists for client 800
com.sap.mw.jco.JCO$Exception: (104) RFC_ERROR_SYSTEM_FAILURE:      No logical system exists for client 800
at com.sap.mw.jco.MiddlewareJRfc.generateJCoException(MiddlewareJRfc.java:455)
at com.sap.mw.jco.MiddlewareJRfc$Client.execute(MiddlewareJRfc.java:1442)
at com.sap.mw.jco.JCO$Client.execute(JCO.java:3962)
at com.sap.mw.jco.JCO$Client.execute(JCO.java:3399)
at com.sap.ip.bi.base.application.service.rfcproxy.impl.jco640.Jco640Proxy.executeFunction(Jco640Proxy.java:255)
Caused by: com.sap.ip.bi.base.exception.BIBaseRuntimeException: Jco exception thrown while executing function "RSWR_METADATA_GET" against system "BIXCLNT800"
at com.sap.ip.bi.base.application.service.rfcproxy.impl.RfcFunction.execute(RfcFunction.java:49)
... 44 more
Caused by: com.sap.mw.jco.JCO$Exception: (104) RFC_ERROR_SYSTEM_FAILURE:      No logical system exists for client 800
at com.sap.mw.jco.MiddlewareJRfc.generateJCoException(MiddlewareJRfc.java:455)
at com.sap.mw.jco.MiddlewareJRfc$Client.execute(MiddlewareJRfc.java:1442)
at com.sap.mw.jco.JCO$Client.execute(JCO.java:3962)
at com.sap.mw.jco.JCO$Client.execute(JCO.java:3399)
at com.sap.ip.bi.base.application.service.rfcproxy.impl.jco640.Jco640Proxy.executeFunction(Jco640Proxy.java:255)
at com.sap.ip.bi.base.application.service.rfcproxy.impl.jco640.Jco640Function.executeRfc(Jco640Function.java:73)
at com.sap.ip.bi.base.application.service.rfcproxy.impl.RfcFunction.execute(RfcFunction.java:47)
... 44 more
Any help on this would be greatly appreciated
- V

Priya, ya its already there/..this is the SM50 trace
N dy_signi_ext: ticket expired
N Mon Jun 4 17:57:44 2007
N dy_signi_ext: SSO TICKET logon (client 800)
N mySAPUnwrapCookie: was called.
N HmskiFindTicketInCache: Trying to find logon ticket in ticket cache.
N HmskiFindTicketInCache: Try to find ticket with cache key: 800:BB1DDE5432D1DBECA778E0DC15AA6852 .
N HmskiFindTicketInCache: Couldn't find ticket in ticket cache.
N I don't need to ask RunningCompatibly to know: I'm >= 46C.
N mySAP: Got the following SSF Params:
N         DN     =CN=BIX
N         EncrAlg=DES-CBC
N         Format =PKCS7
N         Toolkit =SAPSECULIB
N         HashAlg =SHA1
N         Profile =/usr/sap/BIX/DVEBMGS20/sec/SAPSYS.pse
N         PAB =/usr/sap/BIX/DVEBMGS20/sec/SAPSYS.pse
N Got the codepage 4102.
N Got ticket (head) AjExMDAgAA9wb3J0YWw6ZXBfYWRtaW6IAAdkZWZh. Length = 492.
N MskiValidateTicket returns 0.
N Got content client = 000.
N Got content sysid = EPX     .
N Got date 200706042239 from ticket.
N Cur time = 200706042257.
N Computing validity in hours.
N Computing validity in minutes.
N CurTime_t = 1181084220, CreTime_t = 1181083140
N validity: 120, difference:   1080.000.
N *** ERROR => HMskiCheckValidity failed. [ssoxxkrn.c   856]
N dy_signi_ext: ticket expired
Vaib

BEx Web Analyzer error in Portal

Hi,
I'v integrated the BI 7.0 with Portal 7.0. Both systems (BI and Portal) running on different servers, SSO is configured both ways and RFC communication is configured from ABAP to J2EE. However when i run the BEx Web Analyzer iView under the Business Intelligence role, i get the following error:-
The initial exception that caused the request to fail, was:
     No logical system exists for client 800
com.sap.mw.jco.JCO$Exception: (104) RFC_ERROR_SYSTEM_FAILURE:      No logical system exists for client 800
at com.sap.mw.jco.MiddlewareJRfc.generateJCoException(MiddlewareJRfc.java:455)
at com.sap.mw.jco.MiddlewareJRfc$Client.execute(MiddlewareJRfc.java:1442)
at com.sap.mw.jco.JCO$Client.execute(JCO.java:3962)
at com.sap.mw.jco.JCO$Client.execute(JCO.java:3399)
at com.sap.ip.bi.base.application.service.rfcproxy.impl.jco640.Jco640Proxy.executeFunction(Jco640Proxy.java:255)
Caused by: com.sap.ip.bi.base.exception.BIBaseRuntimeException: Jco exception thrown while executing function "RSWR_METADATA_GET" against system "BIXCLNT800"
at com.sap.ip.bi.base.application.service.rfcproxy.impl.RfcFunction.execute(RfcFunction.java:49)
... 44 more
Caused by: com.sap.mw.jco.JCO$Exception: (104) RFC_ERROR_SYSTEM_FAILURE:      No logical system exists for client 800
at com.sap.mw.jco.MiddlewareJRfc.generateJCoException(MiddlewareJRfc.java:455)
at com.sap.mw.jco.MiddlewareJRfc$Client.execute(MiddlewareJRfc.java:1442)
at com.sap.mw.jco.JCO$Client.execute(JCO.java:3962)
at com.sap.mw.jco.JCO$Client.execute(JCO.java:3399)
at com.sap.ip.bi.base.application.service.rfcproxy.impl.jco640.Jco640Proxy.executeFunction(Jco640Proxy.java:255)
at com.sap.ip.bi.base.application.service.rfcproxy.impl.jco640.Jco640Function.executeRfc(Jco640Function.java:73)
at com.sap.ip.bi.base.application.service.rfcproxy.impl.RfcFunction.execute(RfcFunction.java:47)
... 44 more
Any help on this would be greatly appreciated
-V

Hi Deepu,
All the parameters in the SAP_BW system is correct and i have tested the ITS, WebAS and Connector tests also and everything is green. In the BI diagnostic tool everything was green however in the RSPOR_SETUP the Maintain User Assignment was getting failed, so i removed the UME Master System (Reference system) from the Portal as i'm using the SAP Logon Tickets both ways. So there is no need for the reference system. After that RSPOR_SETUP is okay and in the BI Diagnostic tool one is red (UME Master system).
One thing i have noticed in the RSPOR_SETUP now that it tells me in the second step:-
com.sap.ip.bi Java classes with different versions.
Different ABAP and Java Support packages
ABAP support package 12
Java Support package   11
Vaib
Any clue??
Vaib

Analyze error in RWB

After some performace testing I have an error in rwb (sender )
Transmitting the message to endpoint http://xi:8000/sap/xi/engine?type=entry using connection AFW failed, due to: Received HTTP response code 500 : Internal Server Error.
smq1/smq2 doesn't show messages
runtime cache is updated
Message status is waiting
How to analyze what's happen with Integration Engine?

Denis
A HTTP Response in the Adapter Framework can be caused by the following:
The J2EE server might be overburdened and cannot accept the call. The 'Receive'servlet is not called. You will find further details on the HTTP status code definitions under "http://www.w3.org". Check the accessibility of the server by calling: http://<hostname>:<port>/MessagingSystem/receive/AFW/XI.
The Listener Beans of the affected connection (AFW, Marketplace, BC,see above) were not registered or the log-specific Event Handler was not found.
To debug this go to SAP Notes: 803145
---Mohan

GPIB write error code 6, how to do proper wait in GPIB comm

Hi!
I use a Keithley MUX and a DVM to measure different values in my system, including 4 wire resistance. My project runs for several hours without any problem, but last night I have got an error after approx. 8 hours runtime. My error out in the main vi shows the following error:
GPIB Write in A_4Wire_resMUX_2!1,2!3,2!5_new.vi Error code 6.
I have attached this subvi, as you can see, I have put a while loop in the subvi, to give enough time for the 4Wire measurement to be done. But of course maybe another GPIB write function crashes in the subvi, not the one after the while loop.
I have 2 questions:
1. what is the best way to do error handling in GPIB comm., so I could see on my final error out what element caused the problem in this certain subvi?
2. Can someone show me what I could do better in this subvi, to avoid possible GPIB errors?
Its just guessing, but I think the error comes from that I may not give enough time to the GPIB device to perform an action, so the next GPIB write crashes?
plus info: WindowsXP, LabView 2010 Full version
Thanks very much for advice and help!
Solved!
Go to Solution.
Attachments:
A_4Wire_resMUX_2!1,2!3,2!5_new.vi ‏35 KB

2001 driver
7001 driver
Now that you have a modern version of LabVIEW why are you not taking advantage of the instrument driver network? VISA is wonderful and the raw 488.2 primitives should be considered "obsolete".
Since you did not use the specific instrument driver vi's we can't tell which write to what device generates the error you are seeing.
So to specifically answer Q1. Use the Driver's found on the instrument driver network- they are tested and structured in ways that assist in debugging your application and take advantage of powerful features in VISA..
And 2) (see #1) and change the stacked sequence into a state machine
Jeff

PNA Guided Calibration: GPIB write error in for loop

Hi,
I have a LabVIEW program that creates a Guided Power Calibration on a PNA.
After initializing everything properly, I have a for loop that loops through all the manual steps that the user must go through (ex: Connect Channel A of Power meter to Port 1" "Connect male Short to port 1" etc).
The problem is, the program displays an error at the first command: sens:corr:coll:guid:acq STAN1
I says there is an error with the GPIB Write function.
Here are the commands I send:
SYSTRES
DISPlay:WINDow2TATE ON
CALCulate2ARameterEFine:EXT 'MyMeas',S21
DISPlay:WINDow2:TRACe1:FEED 'MyMeas'
CALC1AREL 'CH1_S11_1'
SENS:FREQTAR 2e9
SENS:FREQTOP 4e9
SENSWEOINTS 3
SENS:CORR:COLL:GUID:CONNORT1 'APC 2.4 male'
SENS:CORR:COLL:GUID:CONNORT2 'APC 2.4 male'
SENS:CORR:COLL:GUID:CKITORT1 '85056D'
SENS:CORR:COLL:GUID:CKITORT2 '85056D'
SENSe:CORRection:COLLect:GUIDedSENsor1 ON
SYSTem:COMMunicateSENsor gpib, "13"
SENSe:CORRection:COLLect:GUIDedSENsor1OWer:LEVel -20
sens:corr:coll:guid:init
sens:corr:coll:guid:steps?
//for loop from 1 to total_number_of_steps
sens:corr:coll:guid:desc? <step#>
sens:corr:coll:guid:acq STAN<step#>
The program quits right at the first step, when I send "sens:corr:coll:guid:acq STAN1", although the command is executed.
Also, the VBScript with the same commands works fine.
Can anybody help me? I've been stuck for a while now.
I attached the block diagram of the for loop.
Thanks in advance,
Nicolas
Attachments:
Guided cal for loop.vi ‏27 KB

Sending SENS:corr:coll:guid:acq STAN1 \n gives me a different error: -101 "Invalid Character".
From my different attempts at figuring this out, I thought the problem would come from LabVIEW, since the vbscript with the same commands works on the PNA.
I also modified the for loop because I thought each iteration should be linked to the previous one with the error wire (see attached).
I still have the same issue, only the first iteration is executed, then the program quits.
Attachments:
Guided cal for loop.vi ‏28 KB

BEx Analyzer Error "NO APPLICATION DATA FOUND".

Hello Experts,
I have a problem, when i am going to create a query in BEx analyzer.
I got this Error "NO APPLICATION DATA FOUND".
I already check that Particular InfoCube, The Cube is fine and also it contains Data.
But the Problem begins Same.
Thankyou,
Kshitij Deshmukh

Hello,
I have solved this problem on my own.
Solution: 1st check your target over query is excuting...there is data or no... in Tcode "LISTCUBE".
Then data is available... or not.
If every thing is ok...then dorp the query....create anothor and checked by only 2 fields....if is working then ....comptele it.....if data is there then no problem....report should run...
check ur data is ready for reproting.... i means reporting icon is available or not.????
If the Problem begin Same "NO APPLICABLE DATA FOUND".
Then the Problem in Loading.
2. Click on cube choose manage tab...there will be reproting symbol....
Need to check each steps if data is there or Report not running....
Finally delete the request then again load the data..and icon should come automatically...
3. There is R and below one excel sheet fighre...icon
4. Go and make a Report in BEx Analayzer..
Data will fetching Automatically....
Thank you
Regards
Kshitij Deshmukh

Analyzer error creating new reports

Has anyone seen this error message? Error while executing query and retrieving data.; nested exception is com.hyperion.ap.APException:[1033] Native: -1073741819 Operating system exception thrown I started getting this today when I tried to create any new report to any database connection (old and new DB connections) Old reports still work, but I can't create anything new. Nothing has changed that I am aware of. I tried restarting the service, rebooting the server, uninstalling and reinstalling Java client. Nothing has helped. Nothing in the Hyperion knowledge base. I plan to open a trouble ticket with Support but I have a ticket already opened with them for another issue with Analyzer for about a month now.

Gary,I have seen this issue. As far as I remember it did occur whilecreating the reports. I tried getting this solved but eventuallyhad to reinstall. Are you using desktop client? Are you able tocreate reports from the webclient? Hyperion told me that it wasrelated to some patches that could have been pushed onto themachine but i never believed that.Will try to dig back and see what I got for this.

BEx Analyzer error

When trying to open the BEx analyzer, I get the following error: SAP_CMINIT3 : rc=20 > Connect to SAP gateway failed.
I can access the Bex analyzer using the RRMX transaction.
Waiting for your answer
Thank you
Ramona Leabu

Hi,
your excel server connection is broken.Try to login once again with RRMX or else from start menu.
Regards,
Nikitha

Bex Analyzer error -2147417848

Hi ,
I am getting following error
Run-time error '-2147417848 (80010108)':
Automation error
The object invoked has disconnected from its clients..
Value help window crashes with error -2147417848 (80010108) .
This happens, when selecting a value by moving to the right handside of value help selection window in Query Designer or Analyzer.
Sometimes, this is followed by an runtime error '440'.
When I serached the forum I found that i need to look Note 1039191 - "Value help window crashes with run-time error -2147417848.
Please tell me how do I look at the oss note.
Thanks.

Run-time error '-2147417848 (80010108)':
Automation error
The object invoked has disconnected form it's clients.
Once you are working with SAP BW BEx tool and accessing different version of SAP BW you might encounter an error in BEx Query Designer says:
> u201C"Run-time error '-2147417848 (800010108)': Automation error The object invoked has disconnected from its clients".u201D
BEx Query Designer crashes afterwards.
Solution is to replace the RFC library librfc32.dll stored in your \WINDOWS\system32 on the client PC with a proper version depends on you SAP GUI version:
620: Version >= 6206.6.1938.4727 (620x.x.x.4727).
640: Version >= 6400.3.79.4740 (640x.x.x.4740).
710: check the newest patch of SAP GUI on SAP FTP server.
Thanks,
Arun Bala G

BEx Analyzer error -2147417848 (80010108)

Good morning,
We are upgrading our GUI from 6.40 to 7.10, and with that, Analyzer 3.5 is reinstalled. When we try to open Query designer 3.5 or Analyzer 3.5, we get Run-time error -2147417848 (80010108), method logon of object _CSAPLogonConnection failed. We are unable to go any further. And advise would be greatly appreciated.

Hi Hari,
Thks for the answer, that resolved the issue.
I just have a question, Im in the process to test Office 2010 and when I try to run BEx, Excel raise the following error.
*"Excel was able to open the file by repairing or removing the unreadable content."*
*"This workbook has lost its VBA project, ActiveX controls and any other programmability-related features."*
Do you know if we will be able to run BEx in office 2010? Does anyone knows if microsoft is taking care about make their office versions compatible with SAP?

BEx Analyzer error in loading DLL

Hello I have problem with BEx Analyzer. Each time I try to open it, there is an error message:
Microsoft Visual Basic
Error in loading DLL .
Last weak it was working! Do I need instal latest patch or what happend?
Thanks for reply.
Edited by: Marcel Horkovy on Mar 29, 2008 4:17 PM

Problem solved. I instaled MS Visio (MS Office) but last weak I uninstaled it. BEx Analyzer wasn´t working. So I tried to instal MS Visio again. And here we are. BEx Analyzer is working. I uninstaled Visio again and BEx Analyzer is still working.
Edited by: Marcel Horkovy on Mar 29, 2008 5:38 PM

Keithley 6517B GPIB Write Error 7

Hello,
I have a Keithley 6517B running and communicating with PC through GPIB. The program was initially running fine, and giving the current-noise signal against applied voltage (as programmed). But now when I run the program , it is giving an error that arises at the 6517 Reset/Preset.vi -
Error 7 occurred at GPIB Write in Keithley 6517A Reset / Preset.vi
How do I get rid of this error. I don't understand how suddenly an error arised when I changed nothing in the program or settings of the keithley. The keithley is configured at GPIB address 27.
I am attaching the main program and the sub.VI llb file .
Now when I run the main program, the graph does not show any current or noise signal, but it shows a straight line plotted along '0' along the x-axis (that is, against time or voltage)
Please help.
Best Regards,
Poulomi Das.
Institute for Microsystems Engineering.
University of Freiburg.
Freiburg, Germany.
Attachments:
VI Measurements_v4.vi ‏45 KB
kei6517v6.llb ‏1213 KB

Hello Mike,
I was on leave hence the late reply. I have attached the entire LV main vi with the sub VIs llb file to the very first message on this post. I have attached them again to this message.Do you mean something else?
Best Regards,
Poulomi Das.
Institute for Microsystems Engineering.
University of Freiburg.
Freiburg, Germany.
Attachments:
VI Measurements_v4.vi ‏45 KB
kei6517v6.llb ‏1213 KB

GPIB analyzer error

Similar Messages

Maybe you are looking for