Gpib and interface select problem

Hi,
Max gives me the following:
-primary address: 7
-secondary address: none
-gpib interface number: 1
If I try to communicate with the instrument in labview using the the gpib write.vi with "1: 7" as the address string I get error 30.
Why?
However writing to the instrument in Max is no problem.
Bye.

Change your address string to "1:7", instead of "1: 7".

Similar Messages

GPIB and RS232 communication problems

I've been having several "interesting" problems with GPIB and RS232 communications in LabVIEW VIs. Some I'll mention at the end for curiosity, but right now I'm facing a rather big problem. I'm essentially self-taught at doing LabVIEW (using 8.5.1 right now), but by now I've had a lot of experience as their either has not been any drivers or pre-made VIs for the instruments I've needed or I've not been able to get the available drivers to work and had to write my own anyway (such as with the HP 3458A), but nothing seems to be working right now. I'm not at work, but we typically find forum sites blocked anyway (I can't even download the NI drivers at work since they house them on a ftp server, go figures) so I can't give the VI itself (it wouldn't be easy to get approval even if I could) so the best I can do right now is in words describe everything I've tried. I will be happy to post follow-ups of specific details if I can if they would be helpful.
I've been working on a routine to read data from an MKS 670 Signal Conditioner/Display with a MKS 274 Multiplexer with 3 connected MKS 690A Baratrons. Previously I've worked on programs using other older displays and the analog outputs which were being read by a DAQ card, but for a new project it was decided to try and just read the data directly. I first worked with a unit with just an RS232 Serial Port which I managed to get to work, but had so much problems with garbage readings and having to add checks and re-reads that by the end no matter what delays I added between each reading and how simplified the command routine down to just 2 sequences and the read that it took at least 10 seconds to get 1 reading from each channel.
Figuring maybe it was a limitation of the serial communications for these instruments I tried to re-work it for a unit with a GPIB port with which I'm actually much more familiar. The problem is that I cannot get anything at all from the unit through GPIB. Everything even the bare-bones built-in GPIB CLR function times out with no response from the instrument no matter how long I set the timeout limit and it also freezes the entire GPIB bus as well. It isn't a waiting issue as it freezes on the very first command. The GPIB initialization function seems to work (I typically find this to be unnecessary), but the instrument itself doesn't even respond with a status code. I've also tried just the basic GPIB write functions with even just passing the <cr> and <lf> characters as well. In Measurement and Automation Explorer most of the time the instrument won't even appear when doing search for instruments and when it does it shows as not responding to the *IDN? command (yes I've messed with the EOI, EOS, etc settings and I've even changed the GPIB address even though when it gets this far it confirms that I have the correct address) and even tried manually doing the *IDN?, *RST, and *CLR commands even with <cr> and <lf> characters which the manual for these units clearly states are compatible commands and NI SPY and everything show no response at all. I've tried 2 different GPIB units, 3 different computers including several that are not online and haven't been updated for a while, and using older LabVIEW versions, extensive re-booting and resetting of computers and devices and still nothing. I'm using an NI GPIB-USB-HS GPIB to USB adaptor which I've used extensively on other systems and even re-connected to those systems and everything worked fine. When I hooked up equipment that I knew was working, it would either freeze the entire GPIB bus until well past whatever timeout setting I set at which point all the instruments would appear, but none responding to *IDN? queries or nothing would appear at all, or if I manually turned it off when frozen the other instruments would work and most even respond to the *IDN? queries. The same goes for both of the GPIB instruments of this type that I tried and again for different versions of LabVIEW, difference computers (all Windows XP though), and every GPIB configuration setting I can find to mess with in every combination.
Any thoughts or suggestions would be greatly appreciated. I've had all sorts of weird problems with equipment and LabVIEW (you've got to love undocumented design features) that have frustrated me before, but I've never had an instrument never respond at all especially a GPIB one. Getting garbage yes, no response at all, no.
The side side issues I'm just mentioning as they may be related, but I'm really interested in the above as I have working solutions for these:
One I've had is with a Hart Scientific (prior to being bought by Fluke) 1560 Black Stack that would continually stop responding to GPIB commands when on a continual read function taking readings just every 4 seconds with 250ms between each GPIB read or write command but for up to hours in total and the times it stops responding are random as far as I can tell. I even started sending the *RST command before and after every read or write command and still it freezes. The only thing is to manually turn it off and then back on or manually go through the menus and manually trigger the GPIB reset routine at which point it immediately starts responding. However, when I got sick of having to babysit it and just decided to try the RS232 serial port (as that is all it has without the extended communications module) it works fine no problem and I can even get readings slightly faster from it. Using a Hart Scientific 1529 Chub-e it could give me data on all 4 channels every second without problems. I just find it a bit odd.
When I couldn't get any of the HP 3458A driver packs to work to even give a single measurement reading and just made my own using basic GPIB read/write commands using the programming manual I still have a few interesting problems in randomly when reading off the full possible 256 bytes on the bus and clearing the bus I often find garbage partial readings on the bus every now and then. I've added a few routines to do some basic checks, but it is annoying. What is really weird is when just doing basic DC Voltage reads the "-" sign will randomly be dropped from some readings (started as about 1 out of every 5, down now to about 1 out of every 10). Fortunately I'm taking several readings and averaging and taking the standard deviation with limits on the deviations and basically added a routine to say if there is even 1 negative number take the absolute value of all then make all negative, but again I find it weird.
Thanks.
-Leif
Leif King
Metrology Engineer
Oak Ridge Metrology Center

Greetings Leif,
I understand you have completed extensive troubleshooting techniques to pin-point the problem with the GPIB communication. To begin, I want to ask you a few questions to help me understand your set-up and the issue at hand.
1) Is the NI GPIB-USB-HS cable the one which cannot communicate with your instrument?
2) When using the GPIB-USB-HS, does the GPIB interface show up in MAX?
3) If yes, does the instrument appear in MAX after scanning for instruments (from what I understand in your issue, it does so in an intermittent manner..)?
4) What driver version of VISA do you have installed in your computer?
5) Are you able to communicate to the same instrument using another GPIB cable?
Thank you for trying out some of these steps again, but we want to make sure we rule out other aspects in the systems which might be affecting the GPIB communication.
As for your other issues, please post seperate threads for each so we can help you accordingly. Thanks!
Sincerely,
Aldo
Aldo A
Applications Engineer
National Instruments

PCMCIA-GPIB and IBM 760XD Problem

I have two IBM 760XD identical laptops. Both have the latest BIOS update (hxet60ww). I've tried W2K SP1, WinME, and NT4 SP3 with similar results. I'm trying to use a PCMCIA- GPIB card and consistently get "One or more GPIB interfaces failed." at the "GPIB Interfaces Sequentially Verified" in the NI-488.2 Troubleshooting Wizard. NI-488.2 Software presence was verified as was the GPIB hardware presence verified. Double-click on the GPIB0 line and the Troubleshooting Wizard comes back with "Unknown Hardware Error" and various suggestions. I've tried the instructions (multiple reboots, card in/card out) to no avail. I've hot-inserted the card in W2K, the O/S installs the hardware, I reboot, same results. Same using
the NI-488.2 "Add GPIB Hardware". Version is ni488216. Any help is appreciated. Thanks.

If the revision number is C or lower, there can be problems and the card should be exchanged see http://www.ni.com/cgi-bin/search/search.cgi?scope=knowledgebase&query=1D3CIEGX for more details.
It may be a defective card. If possible, try another PCMCIA-GPIB card in that system. If it does have to be returned, RMA's are only done through phone support (512-795-8248).
Randy Solomonson
Applications Engineer
National Instruments

Glitchy cursor and tool selection problems

Hello all,
I recently updated to the latest version of Premiere Pro AND OS X Yosemite. Today I opened Premiere for the first time since the update and started editing.
Upon editing I began to realize that every time I try to make an edit buy using the razor tool, or any tool for that matter the mouse glitches.
For example: When I try and grad the end of a clip and drag, the cursor bounces between the red arrow and my mouse cursor. Does that make sense?
Also, when I have ANY tool selected it shows my mouse cursor in stead of the icon for the tool. And when I have the selection tool selected to drag a clip it is selecting the rolling edit tool, or the ripple edit tool making it almost impossible to make the edits that I need.
So, my question is, Is this a Premiere Pro bug or a Mac bug? And can I go about fixing this somehow?
Thanks for any help you can give me.

I did just find out that the new hard drive that was put into my computer (i needed more space) is a hybrid. Is this going to be a big factor to these problems? Both me and the other co-worker have hybrid hard drives.

Interface Builder: Problems with selecting items?

Hello, does someone else have experience with IB selection problems?
I did the following:
-Created a textured window
-Dragged a toolbar into it
-Dragged a NSScrollView into the textured window
-Gave the NSScrollView a white background
-Scaled the NSScrollView so that it extended to the edges of the window
-Dragged 4xCheckboxes into the NSScrollView
After this I had major problems in selecting any of the Checkboxes. It seemed like if I moved the mouse around a bit and kept clicking, then in some point I was able to get the checkbox selected. However this happened only after 5-30 clicks. Also the scaling controls of the checkboxes were almost impossible to find and to use.
Is there a button or a checkbox in the IB configuration, or a keyboard key or something in the IB that would make selecting things a bit easier. Or am I just doing something wrong?

Interface Builder is pretty buggy to begin with, so that is always going to be a hassle. You normally have to double-click inside scroll views to get to the actual contained items. Also, you can drill down through the scroll view in the object window in tree view and select the checkbox itself.

When opening Bridge (CS6) I get the following message: "Bridge encountered a problem and is unable to read the cache. Please try purging the central cache in Cache Preferences to correct the situation" I tried and after selecting purge cache it does not a

When opening Bridge (CS6) I get the following message: "Bridge encountered a problem and is unable to read the cache. Please try purging the central cache in Cache Preferences to correct the situation" I tried and after selecting purge cache it does not allow me to select OK. Also Bridge keeps saying "Building Criteria" with the spinning wheel and nothing happens. I tried uninstalling and reinstalling to no avail. Please help:)

Maybe a Preferences reset can help:
Numerous program settings are stored in the Adobe Bridge preferences file, including display, Adobe Photo Downloader, performance, and file-handling options.
Restoring preferences returns settings to their defaults and can often correct unusual application behavior.
Press and hold the Ctrl key (Windows) or the Option key (Mac OS) while starting Adobe Bridge.
In the Reset Settings dialog box, select one or more of the following options:
Reset Preferences
Returns preferences to their factory defaults. Some labels and ratings may be lost. Adobe Bridge creates a new preferences file when it starts.
Purge Entire Thumbnail Cache
Purging the thumbnail cache can help if Adobe Bridge is not displaying thumbnails properly. Adobe Bridge re-creates the thumbnail cache when it starts.
Reset Standard Workspaces
Returns Adobe predefined workspaces to their factory default configurations.
Click OK, or click Cancel to open Adobe Bridge without resetting preferences.

Troubles with Agilent gpib/usb interface

I have a problem to use Agilent 82357A gpib/usb interface with NI VISA (os Win98). I have Visa3.0.1. I did all what is written in file niinfo.htm, which containes some advices for running the agilent gpib/usb card with NI software(it is in directory prog. files\agilent\IO Libraries\readme\trouble\) and I also tried most of advices written on the web pages of ni.com. In MAX3 I can only see "miscellaous VISA resources". When I run NIVISAAIC, I can communicate with interface as well as with instrument attached to it. When I close nivisaaic, it returns arror message, that program performed unauthorised operation in module agvisa32.dll. It indicate that trouble is between libraries of NI and Agilent. I tried to install agilent gpib/u
sb driver in many ways, only SICL, or SICL + agilent visa (secondary, side by side), but nothing works. When I run Getting started wizard in run-programs-national instruments-Ni.488.2, it detects no gpib hardware, even MAX indicates some "miscellaous VISA resources". Is there somebody with experiences how to solve this problem.? Thanks

1. I have tried method 1 in that KB you have adviced me. I uninstalled Ni-Visa and instaled HP-Visa (is not clear from the KB description, if HP should be primary or secondary, side-by side. I tried both configurations). Of course MAX does not find gpib board in any case. To solve this problem in the KB is written "you must right-click on the control or constant and select "Allow Undefined Names." In this step I stopped, because in the MAX I did not find where this "constant or control" is. I tried to do right-click on "devices and interfaces", but only "Create new..." menu appears. The right-click on anything in the MAX does not open the menu which contains "Allow undefined names". Can you please, specify where this right-click should be done to allow undefined names and to continue with method1 to reach the goal of using LV for data aquisition.
2. Then I tried method 2 from the KB. I have uninstalled HP-visa; HP-SICL and Ni-Visa3.0 is installed, NiVisaTulip.dll passport is allowed and F5 refresh made. In MAX in the section Devices and Interfaces I can see "? Miscellaneous VISA resources" with "GPIB1::22::Instr" (it is for one device with address 22). Instead of "? Miscellaneous VISA resources" I expected, there will be written something like GPIB1(USB-GPIB). In this point I have few questions.
a) Is it correct if there is only "? Miscellaneous visa resources"?
b) If I configure usb/gpib card with Agilent config. utility to SICL name gpibn and visa name gpibn, where n is some integer, MAX shows everytime gpib1. There is only one gpib card installed in the PC, so I expect there will be gpib0 in the MAX.
Now, when I run nivisaic, I can see gpib interface named gpibn with gpibn::22::instr. I can communicate through this interface to the instrument in the session opened by double-click on the resource. In the Nivisaic there is also another interface marked as unknown-gpibn::intfc and gpibn::servant. I cannot communicate with this interface. When I install HP SICL with HP visa as secondary, side-by-side, this "unknown gpib" disappears. Then nivisaic seems to be OK(but MAX still shows "? miscellaneous visa resources"),the status of each operation in NI Spy is succesfull. I think I did everything required in method 2 of KB but, I cannot perform any data aquisition by LabView. Are there further thinks to do for starting data aquisiton? Thanks for any advices.

I want to edit properties of the interface windows opened while "Open File", "Save Page As" and interface opened during Downloading of any file.

I am doing a small project on dedicated web client where in user automatically logs in non-root user and Firefox automatically starts.
I am using Fedora 14 kernel 2.6.35.12-88.fc14.i686 and Firefox 3.6.16.
I have installed only Gnome in my computer with no Nautilus or other file browser on it.
I want to edit properties of the interface windows opened while "Open File", "Save Page As" and interface opened during Downloading of any file.
Please guide me for this.

First, I sent an email to the author of PhotoME to inform him of the serious issues his addon caused with Firefox latest versions.
Now, for those of you who do not have the PhotoME addon and yet experience the same problem that I had and that I described above, I suggest the following strategy.
As PhotoME did cause these problems with Firefox latest versions, I am pretty covinved other addons probably might cause these problems too. Therefore, adopt the following method.
Test one addon at a time to see if this particular addon is behind your Firefox issues like the ones I had.
So, disable one addon only at a time. Then close your Firefox and restart it from scratch and see if you still have your Firefox problems. You must restart the Firefox browser from scratch. If you still have these Firefox problems, re-enable the disabled addon, restart your Firefox (again!) and repeat the same method for every single addon that you have.
Try to be selective by choosing first addons that are more likely to cause your Firefox problems such as not very well-known or not very popular addons (like it was the case for the PhotoME addon).
If this method works or if it does not work, report it on this web page so that others can be helped with your comments.
I hope this method will help you because I was really upset that I had these Firefox problems and I first thought it was the fault of Firefox, only to discover later that this PhotoME addon was the culprit and had caused me such upset.

Shareable object interface cast problem

Hi,
I'm a student working on building a shareable object interface between two applets namely "EWallet" and "EPhone".
I currently use the javacard 2.2.X version and I mean to solve the shareable object interface in this version.
Thus not with servlets in 3.X.X.
The current problem I'm facing is the casting from the base type of shareable interface objects (Shareable) to the EWalletInterface which I need to do operations on the SIO of EWallet.
The code snippet of the EWallet applet (server)
public void verify(byte[] pincode) {
if ( pin.check(pincode, (short)0,(byte)(short)pincode.length) == false )
ISOException.throwIt(SW_VERIFICATION_FAILED);
public void debit(byte debitAmount) {
if (!pin.isValidated())
ISOException.throwIt(SW_PIN_VERIFICATION_REQUIRED);
// check debit amount
if ((debitAmount > MAX_TRANSACTION_AMOUNT) || (debitAmount < 0))
ISOException.throwIt(SW_INVALID_TRANSACTION_AMOUNT);
// check the new balance
if ((short)(balance - debitAmount) < (short)0)
ISOException.throwIt(SW_NEGATIVE_BALANCE);
balance = (short)(balance - debitAmount);
public Shareable getShareableInterfaceObject(AID client_aid, byte parameter){
byte[] ephone_aid_bytes = {(byte)0X15, (byte)0XEF, (byte)0X4D, (byte)0X55, (byte)0X86, (byte)0X60};
if(client_aid.equals(ephone_aid_bytes,(short)0,(byte)ephone_aid_bytes.length) == false)
return null;
if(parameter != (byte)0x01)
return null;
return this;
The code snippet of the EPhone applet (client)
//Helper method
private void makeBankcardDebit(short amount){
AID ewallet_aid = JCSystem.lookupAID(ewallet_aid_bytes,(short)0,(byte)ewallet_aid_bytes.length);
if(ewallet_aid == null)
ISOException.throwIt(SW_EWALLET_AID_NOT_EXIST);
//Error with casting from Shareable to EWalletInterface
EWalletInterface sio = (EWalletInterface)(JCSystem.getAppletShareableInterfaceObject(ewallet_aid, (byte)0x01));
if(sio == null)
ISOException.throwIt(SW_FAILED_TO_OBTAIN_SIO);
byte[] pin = new byte[4];
sio.verify(pin);
sio.debit((byte)amount);
this.balance = (short)(this.balance + amount);
The EWalletInterface code snippet
public interface EWalletInterface extends Shareable {
public void verify(byte[] pincode);
public void debit(byte amount);
The interface is currently both in the EWallet and EPhone packages.
The problem i'm facing is that in the code snippet of EPhone.
The "lookupAID"- and "getAppletShareableInterfaceObject"-methods work
The casting from Shareable to EWalletInterface gives me status word 0x6F00 which presents me with a google explanation of "No precise diagnosis".
Does anyone have an idea why the cast from Shareable to EWalletInterface doesn't work?
Thanks in advance,
Jeroen

Hi,
What happens if you get the SOI reference and store in a Shareable and see if it is null? Just to confirm, the two applets are in different packages and the server applet has be installed and is selectable?
If you get 0x6F00, you should start adding try/catch blocks to find the root cause.
Cheers,
Shane
=================================
Reposting with {code} tags
=================================
Hi,
I'm a student working on building a shareable object interface between two applets namely "EWallet" and "EPhone".
I currently use the javacard 2.2.X version and I mean to solve the shareable object interface in this version.
Thus not with servlets in 3.X.X.
The current problem I'm facing is the casting from the base type of shareable interface objects (Shareable) to the EWalletInterface which I need to do operations on the SIO of EWallet.
The code snippet of the EWallet applet (server)
    public void verify(byte[] pincode) {
        if ( pin.check(pincode, (short)0,(byte)(short)pincode.length) == false )
            ISOException.throwIt(SW_VERIFICATION_FAILED);
    public void debit(byte debitAmount) {
        if (!pin.isValidated())
            ISOException.throwIt(SW_PIN_VERIFICATION_REQUIRED);
        // check debit amount
        if ((debitAmount > MAX_TRANSACTION_AMOUNT) || (debitAmount < 0))
           ISOException.throwIt(SW_INVALID_TRANSACTION_AMOUNT);
        // check the new balance
        if ((short)(balance - debitAmount) < (short)0)
             ISOException.throwIt(SW_NEGATIVE_BALANCE);
        balance = (short)(balance - debitAmount);
    public Shareable getShareableInterfaceObject(AID client_aid, byte parameter){
        byte[] ephone_aid_bytes = {(byte)0X15, (byte)0XEF, (byte)0X4D, (byte)0X55, (byte)0X86, (byte)0X60};
        if(client_aid.equals(ephone_aid_bytes,(short)0,(byte)ephone_aid_bytes.length) == false)
            return null;
        if(parameter != (byte)0x01)
            return null;
        return this;
The code snippet of the EPhone applet (client)
   //Helper method
    private void makeBankcardDebit(short amount){
        AID ewallet_aid = JCSystem.lookupAID(ewallet_aid_bytes,(short)0,(byte)ewallet_aid_bytes.length);
        if(ewallet_aid == null)
           ISOException.throwIt(SW_EWALLET_AID_NOT_EXIST);
        //Error with casting from Shareable to EWalletInterface
        EWalletInterface sio = (EWalletInterface)(JCSystem.getAppletShareableInterfaceObject(ewallet_aid, (byte)0x01));
        if(sio == null)
          ISOException.throwIt(SW_FAILED_TO_OBTAIN_SIO);
        byte[] pin = new byte[4];
        sio.verify(pin);
        sio.debit((byte)amount);
        this.balance = (short)(this.balance + amount);
The EWalletInterface code snippet
    public interface EWalletInterface extends Shareable {
        public void verify(byte[] pincode);
        public void debit(byte amount);
    }The interface is currently both in the EWallet and EPhone packages.
The problem i'm facing is that in the code snippet of EPhone.
The "lookupAID"- and "getAppletShareableInterfaceObject"-methods work
The casting from Shareable to EWalletInterface gives me status word 0x6F00 which presents me with a google explanation of "No precise diagnosis".
Does anyone have an idea why the cast from Shareable to EWalletInterface doesn't work?
Thanks in advance,
Jeroen

GPIB and Desktop RT

I am running the following:
Desktop Labview Real Time 11.0
NI-VISA Server 5.1
and am using an NI PCI-GPIB card to connect to a couple of different pieces of lab equipment.
When I connect to this remote system from another workstation using MAX, I do see GPIB0 (PCI-GPIB) under devices and Interfaces on the RT machine, but I cannot figure out how to see the GPIB instruments that are connected to the bus.
I don't think it is a electrical problem on the bus because when I boot the workstation into windows instead of RT, I can see the instruments just fine using Max on that machine.
Rick
PS: The workstation I use to connect to the RT machine remotely runs a current version of Labview
Rick Foster
MIT Kavli Institute for Astrophysics and Space Research
Solved!
Go to Solution.

The current VISA Interactive Control layout is a bit differenent from the tutorial.
I do see the instruments now, but they are listed under localhost and I get an error when I try to list them on the remote machine that the GPIB controller is installed in.
I can now access the instruments in my code, but this Localhost versus Remote machine bit is confusing.
Rick
Rick Foster
MIT Kavli Institute for Astrophysics and Space Research

NIMax shows error when opening device and interface

I have just installed NI-VISA 3.1. NIMax will not open the devices and interfaces configuration to allow me to see the GPIB and PXI devices.
It gives a message of "NIMax.exe has generated errors and will be closed by Windows. You will need to restart the program."

Hello,
It sounds like an installation has been corrupted. As a general, first-order fix for such problems, you can uninstall and reinstall the program with corrupted files (using add/remove programs from your control panel). To get a better idea for which program has corrupted files, when MAX crashes click the details button (if one shows) in the error message (include such information in any repost as well!). If your system was stable prior to installing NI-VISA 3.1, you can try uninstalling and reinstalling NI-VISA. If you have the time, I would uninstall all of your NI hardware and software, then reinstall your NI software, then reinstall your NI hardware (you should check your hardware manuals to be sure that your specific NI hardware does not require instal
lation before the software). Also, if you could provide the version information for all of your NI software and your current hardware setup (NI and otherwise), it may open other options for solutions!
Thank you,
Best Regards,
JLS
Applications Engineer
National Instruments
Best,
JLS
Sixclear

Exception when "Edit Maps and Interface"

This is pretty uniform on all .jws I tried. Right click on the client
interface and choose "Edit Maps and Interface" yields:
Unexpected exception:
java.lang.NumberFormatException: null
at java.lang.Integer.parseInt(Integer.java:394)
at java.lang.Integer.parseInt(Integer.java:476)
at jellybeans.util.CookingUtil.getErrorCount(CookingUtil.java:159)
at jellybeans.util.CookingUtil.getErrorText(CookingUtil.java:142)
at
jellybeans.modules.jws.dialog.SvcMapEditorDialog$GetDefaultMapTask.runForegr
ound(SvcMapEditorDialog.java:1441)
at
jellybeans.core.task.TaskThread$ExecuteForeground.run(TaskThread.java:164)
at java.awt.event.InvocationEvent.dispatch(InvocationEvent.java:178)
at java.awt.EventQueue.dispatchEvent(EventQueue.java:443)
at
java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.ja
va:191)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
:144)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
:134)
at java.awt.Dialog.show(Dialog.java:524)
at jellybeans.util.AssertUtil$1.run(AssertUtil.java:147)
at java.awt.event.InvocationEvent.dispatch(InvocationEvent.java:178)
at java.awt.EventQueue.dispatchEvent(EventQueue.java:443)
at
java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.ja
va:191)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
:144)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
:134)
at java.awt.Dialog.show(Dialog.java:524)
at
jellybeans.modules.jws.action.EditSvcMapsAction.actionPerformed(EditSvcMapsA
ction.java:93)
at javax.swing.AbstractButton.fireActionPerformed(AbstractButton.java:1767)
at
javax.swing.AbstractButton$ForwardActionEvents.actionPerformed(AbstractButto
n.java:1820)
at
javax.swing.DefaultButtonModel.fireActionPerformed(DefaultButtonModel.java:4
19)
at javax.swing.DefaultButtonModel.setPressed(DefaultButtonModel.java:257)
at javax.swing.AbstractButton.doClick(AbstractButton.java:289)
at
javax.swing.plaf.basic.BasicMenuItemUI.doClick(BasicMenuItemUI.java:1092)
at
javax.swing.plaf.basic.BasicMenuItemUI$MouseInputHandler.mouseReleased(Basic
MenuItemUI.java:932)
at java.awt.Component.processMouseEvent(Component.java:5021)
at java.awt.Component.processEvent(Component.java:4818)
at java.awt.Container.processEvent(Container.java:1380)
at java.awt.Component.dispatchEventImpl(Component.java:3526)
at java.awt.Container.dispatchEventImpl(Container.java:1437)
at java.awt.Component.dispatchEvent(Component.java:3367)
at java.awt.LightweightDispatcher.retargetMouseEvent(Container.java:3214)
at java.awt.LightweightDispatcher.processMouseEvent(Container.java:2929)
at java.awt.LightweightDispatcher.dispatchEvent(Container.java:2859)
at java.awt.Container.dispatchEventImpl(Container.java:1423)
at java.awt.Window.dispatchEventImpl(Window.java:1566)
at java.awt.Component.dispatchEvent(Component.java:3367)
at java.awt.EventQueue.dispatchEvent(EventQueue.java:445)
at
java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.ja
va:191)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
:144)
at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:138)
at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:130)
at java.awt.EventDispatchThread.run(EventDispatchThread.java:98)
Was caught at:
jellybeans.util.AssertionFailureException: Unexpected exception: null
at jellybeans.util.AssertUtil.handleUnexpectedException(AssertUtil.java:50)
at jellybeans.util.AssertUtil.handle(AssertUtil.java:90)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at
sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39
at
sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl
.java:25)
at java.lang.reflect.Method.invoke(Method.java:324)
at
java.awt.EventDispatchThread.handleException(EventDispatchThread.java:304)
at
java.awt.EventDispatchThread.processException(EventDispatchThread.java:210)
at
java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.ja
va:202)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
:144)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
:134)
at java.awt.Dialog.show(Dialog.java:524)
at jellybeans.util.AssertUtil$1.run(AssertUtil.java:147)
at java.awt.event.InvocationEvent.dispatch(InvocationEvent.java:178)
at java.awt.EventQueue.dispatchEvent(EventQueue.java:443)
at
java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.ja
va:191)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
:144)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
:134)
at java.awt.Dialog.show(Dialog.java:524)
at
jellybeans.modules.jws.action.EditSvcMapsAction.actionPerformed(EditSvcMapsA
ction.java:93)
at javax.swing.AbstractButton.fireActionPerformed(AbstractButton.java:1767)
at
javax.swing.AbstractButton$ForwardActionEvents.actionPerformed(AbstractButto
n.java:1820)
at
javax.swing.DefaultButtonModel.fireActionPerformed(DefaultButtonModel.java:4
19)
at javax.swing.DefaultButtonModel.setPressed(DefaultButtonModel.java:257)
at javax.swing.AbstractButton.doClick(AbstractButton.java:289)
at
javax.swing.plaf.basic.BasicMenuItemUI.doClick(BasicMenuItemUI.java:1092)
at
javax.swing.plaf.basic.BasicMenuItemUI$MouseInputHandler.mouseReleased(Basic
MenuItemUI.java:932)
at java.awt.Component.processMouseEvent(Component.java:5021)
at java.awt.Component.processEvent(Component.java:4818)
at java.awt.Container.processEvent(Container.java:1380)
at java.awt.Component.dispatchEventImpl(Component.java:3526)
at java.awt.Container.dispatchEventImpl(Container.java:1437)
at java.awt.Component.dispatchEvent(Component.java:3367)
at java.awt.LightweightDispatcher.retargetMouseEvent(Container.java:3214)
at java.awt.LightweightDispatcher.processMouseEvent(Container.java:2929)
at java.awt.LightweightDispatcher.dispatchEvent(Container.java:2859)
at java.awt.Container.dispatchEventImpl(Container.java:1423)
at java.awt.Window.dispatchEventImpl(Window.java:1566)
at java.awt.Component.dispatchEvent(Component.java:3367)
at java.awt.EventQueue.dispatchEvent(EventQueue.java:445)
at
java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.ja
va:191)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
:144)
at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:138)
at java.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:130)
at java.awt.EventDispatchThread.run(EventDispatchThread.java:98)

Thanks all. I appreciate the help.
"Peter Laird" <[email protected]> wrote in message
news:[email protected]...
>
Me too. I got different errors however because I did something different:
1.) Download and install the public beta.
2.) Start WLS (I started mydomain server)
3.) Start Workshop from the Start Menu.4) Created a new method for my webservice
5) Selected Debug->"Start and Debug"
6) Got ClassNotFound exceptions on my mydomain server console window andWorkshop
showed a progress bar for multiple minutes instead of failing outright.
There seems to be a basic assumption for some users that Workshopinteracts with
the out of the box WLS instance. Its not clear for people that don't readthe
documentation (that's me!) that the WLS instance needs to be Cajun aware.
Perhaps a message dialog should appear upon first install explaininglittle gotchas
like this. It should be one of those windows that you can uncheck "Showthis window
at startup".
Just a suggestion.
"Joe Noonan" <[email protected]> wrote:
Thanks Ian. I also had this problem. I had started WebLogic before
WorkShop and ran into the same problem. Once I read this and started
it
from within WorkShop, it ran fine.
Joe Noonan
[email protected]
"Ian M. Goldstein" <[email protected]> wrote in message
news:[email protected]...
Thanks, Robert. It looks like this error happens when running a
non-Workshop-enabled instance of WebLogic Server.
Note the differences in the classpath settings in the Workshop-enabled
startWebLogic.cmd script
(C:\bea\weblogic700b\samples\workshop\startWebLogic.cmd) as opposedto the
non-Workshop-enabled scripts at
C:\bea\user_domains\mydomain\startWebLogic.cmd or
C:\bea\weblogic700b\samples\server\config\examples\startWebLogic.cmd.
I'll file an issue about improving the error message if the instanceof
WebLogic Server which is running doesn't have the necessary Workshopjars
in
its classpath.
Ian M. Goldstein
Developer Relations Engineer
BEA Systems, Inc.
"Robert Patrick" <[email protected]> wrote in message
news:[email protected]...
Here are the steps to reproduce this.
1.) Download and install the public beta.
2.) Start WLS (probably don't need to do this)
3.) Start Workshop from the Start Menu.
4.) Right Click on the Hello interface and Choose "Edit Maps andInterface".
Hope this helps,
Robert Patrick
Technical Director
BEA Systems
Ian M. Goldstein wrote:
Hi Steve. I'm not seeing this myself with any of the samples or
my own
jws
files. There was a pre-beta issue that fit this description, but
it
was
resolved before the beta release. What build are you running?
(Click
on
Help
About WebLogic Workshop.)
Are you actually modifying the interface when you're getting that
error,
or
does it happen just from opening the "Edit Maps and Interface"
dialog
box?
Once you get the error, can you get past it and try to open the
"Edit
Maps
and Interface" dialog box again? Do you get the error again, or
does
it
let
you actually edit the interface now?
Thanks,
Ian M. Goldstein
BEA Developer Relations Engineer
"Steve Demuth" <sdemuthxxxxartemisalliance.com> wrote in message
news:[email protected]...
This is pretty uniform on all .jws I tried. Right click on the
client
interface and choose "Edit Maps and Interface" yields:
Unexpected exception:
java.lang.NumberFormatException: null
at java.lang.Integer.parseInt(Integer.java:394)
at java.lang.Integer.parseInt(Integer.java:476)
at jellybeans.util.CookingUtil.getErrorCount(CookingUtil.java:159)
at jellybeans.util.CookingUtil.getErrorText(CookingUtil.java:142)
at
jellybeans.modules.jws.dialog.SvcMapEditorDialog$GetDefaultMapTask.runForegr
>>>>>
ound(SvcMapEditorDialog.java:1441)
at
jellybeans.core.task.TaskThread$ExecuteForeground.run(TaskThread.java:164
atjava.awt.event.InvocationEvent.dispatch(InvocationEvent.java:178)
at java.awt.EventQueue.dispatchEvent(EventQueue.java:443)
at
java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.ja
>>>>>
va:191)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
>>>>>
:144)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
>>>>>
:134)
at java.awt.Dialog.show(Dialog.java:524)
at jellybeans.util.AssertUtil$1.run(AssertUtil.java:147)
atjava.awt.event.InvocationEvent.dispatch(InvocationEvent.java:178)
at java.awt.EventQueue.dispatchEvent(EventQueue.java:443)
at
java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.ja
>>>>>
va:191)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
>>>>>
:144)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
>>>>>
:134)
at java.awt.Dialog.show(Dialog.java:524)
at
jellybeans.modules.jws.action.EditSvcMapsAction.actionPerformed(EditSvcMapsA
>>>>>
ction.java:93)
at
javax.swing.AbstractButton.fireActionPerformed(AbstractButton.java:1767)
at
javax.swing.AbstractButton$ForwardActionEvents.actionPerformed(AbstractButto
>>>>>
n.java:1820)
at
javax.swing.DefaultButtonModel.fireActionPerformed(DefaultButtonModel.java:4
>>>>>
19)
atjavax.swing.DefaultButtonModel.setPressed(DefaultButtonModel.java:257)
at javax.swing.AbstractButton.doClick(AbstractButton.java:289)
at
javax.swing.plaf.basic.BasicMenuItemUI.doClick(BasicMenuItemUI.java:1092)
at
javax.swing.plaf.basic.BasicMenuItemUI$MouseInputHandler.mouseReleased(Basic
>>>>>
MenuItemUI.java:932)
at java.awt.Component.processMouseEvent(Component.java:5021)
at java.awt.Component.processEvent(Component.java:4818)
at java.awt.Container.processEvent(Container.java:1380)
at java.awt.Component.dispatchEventImpl(Component.java:3526)
at java.awt.Container.dispatchEventImpl(Container.java:1437)
at java.awt.Component.dispatchEvent(Component.java:3367)
atjava.awt.LightweightDispatcher.retargetMouseEvent(Container.java:3214)
atjava.awt.LightweightDispatcher.processMouseEvent(Container.java:2929)
at
java.awt.LightweightDispatcher.dispatchEvent(Container.java:2859)
at java.awt.Container.dispatchEventImpl(Container.java:1423)
at java.awt.Window.dispatchEventImpl(Window.java:1566)
at java.awt.Component.dispatchEvent(Component.java:3367)
at java.awt.EventQueue.dispatchEvent(EventQueue.java:445)
at
java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.ja
>>>>>
va:191)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
>>>>>
:144)
atjava.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:138)
atjava.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:130)
at java.awt.EventDispatchThread.run(EventDispatchThread.java:98)
Was caught at:
jellybeans.util.AssertionFailureException: Unexpected exception:
null
at
jellybeans.util.AssertUtil.handleUnexpectedException(AssertUtil.java:50)
at jellybeans.util.AssertUtil.handle(AssertUtil.java:90)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at
sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39
>>>>>
at
sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl
>>>>>
.java:25)
at java.lang.reflect.Method.invoke(Method.java:324)
at
java.awt.EventDispatchThread.handleException(EventDispatchThread.java:304
at
java.awt.EventDispatchThread.processException(EventDispatchThread.java:210)
at
java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.ja
>>>>>
va:202)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
>>>>>
:144)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
>>>>>
:134)
at java.awt.Dialog.show(Dialog.java:524)
at jellybeans.util.AssertUtil$1.run(AssertUtil.java:147)
atjava.awt.event.InvocationEvent.dispatch(InvocationEvent.java:178)
at java.awt.EventQueue.dispatchEvent(EventQueue.java:443)
at
java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.ja
>>>>>
va:191)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
>>>>>
:144)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
>>>>>
:134)
at java.awt.Dialog.show(Dialog.java:524)
at
jellybeans.modules.jws.action.EditSvcMapsAction.actionPerformed(EditSvcMapsA
>>>>>
ction.java:93)
at
javax.swing.AbstractButton.fireActionPerformed(AbstractButton.java:1767)
at
javax.swing.AbstractButton$ForwardActionEvents.actionPerformed(AbstractButto
>>>>>
n.java:1820)
at
javax.swing.DefaultButtonModel.fireActionPerformed(DefaultButtonModel.java:4
>>>>>
19)
atjavax.swing.DefaultButtonModel.setPressed(DefaultButtonModel.java:257)
at javax.swing.AbstractButton.doClick(AbstractButton.java:289)
at
javax.swing.plaf.basic.BasicMenuItemUI.doClick(BasicMenuItemUI.java:1092)
at
javax.swing.plaf.basic.BasicMenuItemUI$MouseInputHandler.mouseReleased(Basic
>>>>>
MenuItemUI.java:932)
at java.awt.Component.processMouseEvent(Component.java:5021)
at java.awt.Component.processEvent(Component.java:4818)
at java.awt.Container.processEvent(Container.java:1380)
at java.awt.Component.dispatchEventImpl(Component.java:3526)
at java.awt.Container.dispatchEventImpl(Container.java:1437)
at java.awt.Component.dispatchEvent(Component.java:3367)
atjava.awt.LightweightDispatcher.retargetMouseEvent(Container.java:3214)
atjava.awt.LightweightDispatcher.processMouseEvent(Container.java:2929)
at
java.awt.LightweightDispatcher.dispatchEvent(Container.java:2859)
at java.awt.Container.dispatchEventImpl(Container.java:1423)
at java.awt.Window.dispatchEventImpl(Window.java:1566)
at java.awt.Component.dispatchEvent(Component.java:3367)
at java.awt.EventQueue.dispatchEvent(EventQueue.java:445)
at
java.awt.EventDispatchThread.pumpOneEventForHierarchy(EventDispatchThread.ja
>>>>>
va:191)
at
java.awt.EventDispatchThread.pumpEventsForHierarchy(EventDispatchThread.java
>>>>>
:144)
atjava.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:138)
atjava.awt.EventDispatchThread.pumpEvents(EventDispatchThread.java:130)
at java.awt.EventDispatchThread.run(EventDispatchThread.java:98)

CS4 and pen pressure problem

When drawing with the brush or the clone stamp brush now and then strokes are drawn at full pressure even though that is not the case. The next strokes are ok again for a while and then again... a few strokes like they there was no pen pressure. Very annoying when retouching masks.
I already installed the latest Wacom driver but no joy.
What else could I try?
My graphics card doesn't have OpenGL capacities so I don't think that's the problem or could it?
Also CS4 is much slower than CS3 in updating the screen. Related?
Tips welcome...
I am a long time user of Photoshop (since 2.5) but I think CS4 will be the first upgrade I will skip although I love the new adjustments and masks panels...
Windows XP Pro, 4 Gigs of Ram, Matrox Millenium card, plenty of sratch disk space.

I had exactly the same problem with my Wacom Intuos 3 tablet.
The solution is to go into Control Panel>Administrative Tools>Computer Management>Device Manager>Human Interface Devices and disable Wacom Virtual Hid Driver.
I found that somewhere on the Wacom site and it does it for me.
I'm not sure but I think it started when I updated the Wacom drivers to try and solve another problem.
Can I ask, if you press CNTRL-ALT-DEL to start task manager, does that disable your pen until you select the Task Manager button? That came with the latest driver too.
Brian

Outlook 2010 multiple item select problem

Hi,
I have a maddening issue with Outlook 2010. It has to do with a feature that has always worked 100% issue free in older versions of Outlook.
Outlook is somehow losing its mind where it comes to range selections. Specifically, there are 2 issues, with steps to reproduce.
Issue 1:
step 1) select a message
step 2) scroll down in the inbox, and shift-select a message 30 lines down (note: any number, not just 30, will do)
step 3) right click on the range, and select "Mark as read" (note: any other right-click action will do as well)
note: Upon completion of step 3, the range selection is lost inside of the inbox user interface.
step 4) to regain the view of the selected range, press and hold the shift key and then arrow up then back down
note: Upon completion of step 4, the entire range of 30 messages is shown as selected once more
Issue 2:
step 1) select a message
step 2) scroll up in the inbox, and shift-select a message 30 lines above (note: any number, not just 30, will do)
step 3) right click on the range, and select "Mark as read" (note: any other right-click action will do as well)
Upon completion of step 3, the range selection is lost inside of the inbox user interface.
step 4) to regain the view of the selected range, press and hold the shift key and then arrow up then back down
note: Upon completion of step 4, the entire range of 30 messages is NOT shown as selected; rather, only the number of messages that fit in the inbox view that were part of the selection are shown as highlighted. ie, if only 10 of the 30 fit in the
current view, only the 10 are shown as selected.
This is maddening, as it does not happen every single time.
Workarounds I have tried that did not solve the issue:
1) Update all BIOS and driver settings to the latest editions
2) Replace the mouse
3) Turn off the preview pane
4) Deleted the existing Outlook profile, and then created a new one
Please advise, this is an infuriating issue, which never occurred with older editions of MS Outlook!

Hello,
I tried your steps, but I cannot reproduce step 3. The selection didn't lost when I right clicked on the range and selected "Mark as read".
Please try to open Outlook in safe mode to check if the problem persists. To open Outlook in safe mode, press Windows key + R to open the Run command, type
outlook /safe and press Enter.
Regards,
Steve Fan
TechNet Community Support
It's recommended to download and install
Configuration Analyzer Tool (OffCAT), which is developed by Microsoft Support teams. Once the tool is installed, you can run it at any time to scan for hundreds of known issues in Office
programs.

A720 and windows 8 problems

Im trying to setup the a720 with windows 8 and have this problems: When power off the computer have all time this BSOD : SESSION_HAS_VALID_POOL_ON_EXIT Touchscreen not work.
If I run the windows 8 install, just for test, the touch is working, the problem is after install.
External hard disk not working when connect to any USB port, and unplug result in a system freeze.
Here my mini dump for error SESSION_HAS_VALID_POOL_ON_EXIT, I have the i5 model too and this not happen on that model:
Crash Dump Analysis provided by OSR Open Systems Resources, Inc. (http://www.osr.com) Online Crash Dump Analysis Service See http://www.osronline.com for more information Windows 8 Kernel Version 9200 MP (8 procs) Free x64 Product: WinNt, suite: TerminalServer SingleUserTS Built by: 9200.16384.amd64fre.win8_rtm.120725-1247 Machine Name: Kernel base = 0xfffff800`60081000 PsLoadedModuleList = 0xfffff800`6034ba60 Debug session time: Wed Nov 28 17:08:03.203 2012 (UTC - 5:00) System Uptime: 0 days 0:00:13.897 ******************************************************************************* * * * Bugcheck Analysis * * * *******************************************************************************
SESSION_HAS_VALID_POOL_ON_EXIT (ab) Caused by a session driver not freeing its pool allocations prior to a session unload. This indicates a bug in win32k.sys, atmfd.dll, rdpdd.dll or a video driver. Arguments: Arg1: 0000000000000001, session ID Arg2: 00000000000000f0, number of paged pool bytes that are leaking Arg3: 0000000000000000, number of nonpaged pool bytes that are leaking Arg4: 0000000000000001, total number of paged and nonpaged allocations that are leaking. nonpaged allocations are in the upper half of this word, paged allocations are in the lower half of this word.
Debugging Details: ------------------
TRIAGER: Could not open triage file : e:\dump_analysis\program\triage\modclass.ini, error 2
CUSTOMER_CRASH_COUNT: 1
DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT
BUGCHECK_STR: 0xAB
PROCESS_NAME: csrss.exe
CURRENT_IRQL: 0
LAST_CONTROL_TRANSFER: from fffff80060680506 to fffff800600fc040
STACK_TEXT: fffff880`05d059b8 fffff800`60680506 : 00000000`000000ab 00000000`00000001 00000000`000000f0 00000000`00000000 : nt!KeBugCheckEx fffff880`05d059c0 fffff800`603e8bb5 : fffff880`04983b40 00000000`00000000 fffff880`04983000 ffffffff`ffffffe6 : nt! ?? ::NNGAKEGL::`string'+0x36216 fffff880`05d05a10 fffff800`604a48b6 : 00000000`00000372 fffff880`04983000 fffffa80`090203c0 fffffa80`08fc4540 : nt!MiDereferenceSessionFinal+0xf1 fffff880`05d05a80 fffff800`604abe68 : fffff8a0`00142b00 00000000`00000000 00000000`00000001 00000000`00000001 : nt!MmCleanProcessAddressSpace+0x2be fffff880`05d05af0 fffff800`604ac55e : fffffa80`00000000 00000002`00000001 00000000`00000000 fffff8a0`00d0b8f0 : nt!PspExitThread+0x668 fffff880`05d05c10 fffff800`600e1dd6 : fffff800`60377180 00000000`00000080 fffffa80`090203c0 fffffa80`08fc4540 : nt!PspTerminateThreadByPointer+0x4e fffff880`05d05c60 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiStartSystemThread+0x16
STACK_COMMAND: kb
FOLLOWUP_IP: nt! ?? ::NNGAKEGL::`string'+36216 fffff800`60680506 cc int 3
SYMBOL_STACK_INDEX: 1
SYMBOL_NAME: nt! ?? ::NNGAKEGL::`string'+36216
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: nt
IMAGE_NAME: ntkrnlmp.exe
DEBUG_FLR_IMAGE_TIMESTAMP: 5010ac4b
FAILURE_BUCKET_ID: X64_0xAB_nt!_??_::NNGAKEGL::_string_+36216
BUCKET_ID: X64_0xAB_nt!_??_::NNGAKEGL::_string_+36216
Followup: MachineOwner ---------

Ok, the problem is generated by NVIDIA VIDEO DRIVER!
Honesty I cant understand why LENOVO not choose for this machines a ivibridge CPU with HD4000 VIDEO, performance is similar, and Intel VIDEOS GPU, have 0 troubles, ATI AND NVIDIA always are very problematic.
Anyway the solution is simple:
1 Turn OFF windows update, or change to selective install.
This prevent win update install NVIDIA driver in automatic way.
2 Uninstall NVIDIA driver sand NVIDIA related stuff.
3 Restart the machine, NOT POWER OFF, just restart.
4 Now go to SYSTEM PROPERTIES > HARDWARE > DEVICE MANAGER
INSIDE DISPLAY ADPATER NOW SELECT DISABLE THE DEFAULT VGA DRIVER, NOR UNINSTALL CHOOSE DISABLE!
NOW RESTART.
After restart now touchscreen work correctly, and next time you power off the machine, not have that ugly error all time.
This not is a final solution is just a workaround until LENOVO/NVIDIA provide a final fix for this.

Gpib and interface select problem

Similar Messages

Maybe you are looking for