GPIB driver for NEC omniace RA1100

Hello,
I want to control a NEC datalogger omniace II RA1100 via GPIB. Does anybody know where I can get the LabView driver for this instrument?
I didn't find them neither on ni.com nor at the NEC website.
Many thanks in advance,
Magnus

Hallo Jens,
kann es sein, dass die Schnittstellenparameter nicht gesetzt sind? Die Parameter für die Schnittstellen werden in der Datei GfSUDI.UDI im DIAdem Programmverzeichnis verwaltet. Falls die Datei nicht existiert, kann die im Attachment vorhandene UDI-Datei in das Diadem Programmverzeichnis kopiert werden. Die Adresse und der Kartentyp müssen mit der Karteneinstellung übereinstimmen.
Ich hoffe das hilft weiter.
Gruß
Walter
Attachments:
GfSUDI.zip ‏1 KB

Similar Messages

Where can I download labview GPIB driver for Electroglas 2001 wafer prober?

Need a copy of Labview GPIB driver for Electroglas 2001 prober. Please let me know where I can download it.
Thanks.

Hi,
All the Instrument Drivers NI has can be found at the Instrument Driver network:
www.ni.com/idnet.
I searched for the instrument you are using and I couldn't find anything on it.
In this case, you can contact the device manufacturer to see if they have a library. If not, you'll need the command set of the instrument. With the command set you can then use the VISA VIs to sent these commands and receive any data from the instrument.
DiegoF
National Instruments.

Where can I download a LabVIEW GPIB driver for an ANDO AQ6315E Optical Spectrum Analyzer?

Where can I download a LabVIEW GPIB driver for an ANDO AQ6315E Optical Spectrum Analyzer?
Thanks.
Solved!
Go to Solution.

The Instrument Driver Network has all the drivers for instruments. There is no driver specific to that model, but there is one for the 6310B. Perhaps that may work for you. You may need to modify it. If not, you will need to write one yourself. You can get a lot of material for this here: http://www.ni.com/devzone/idnet/development.htm

I need GPIB Driver for Keithley 263 Calibrator/Source Meter using Labview. Can anybody help? Thank you.

I need GPIB Driver for Keithley 263 Calibrator/Source Meter using Labview. Can anybody help?
Thank you in advance.

Hi,
on Keithley's website is explained :
"The Model 263 offers a more economical, more precise alternative to the Model 6430 or the Model 236 when used as a low-current source. It is used almost exclusively as a current calibrator."
This leads to Model 236.... A LabVIEW-driver is available @: http://search.ni.com/query.html?lk=1&col=alldocs&nh=500&rf=3&ql=&pw=595&qp=%2BContentType%3AInstrumentDriver+%2BIDNetManufacturer%3A%22Keithley%22&qt=&layout=IDNet
Maybe you have to "reconstruct" some parts - but it will help.
regards
wha

GPIB driver for AVS-46 resistance bridge

Hi,
does anybody have a GPIB driver for an AVS-46 resistance bridge?
I tried to program it by myself, and reading data works, but I found a
problem when I try to change the multiplexer channel programatically.
According to the manual, the GPIB command syntax for this command
should read "M[0....7]", where the number is the channel number. In
practice, this does not seem to work, and I have to switch the
channels manually.
Thanks for help!

Hi,
It seems that there is a driver for the AVS47 up on picowatt's webpage. http://www.picowatt.fi/index1.html. If it does not work exactly with your instrument, it would serve as a good starting point for your driver.
Hope this helps!
Best Regards,
Aaron K.
Application Engineer
National Instruments

HP8563E Spectrum gpib driver for labwindows/dos

Hi
I'm looking for HP8563E Spectrum gpib driver for labwindows/dos.
Best regards

I don't know of a driver, but you can download from agilent their Spectrum Analyzer compatability guide which cross references their analyzer's GPIB commands and create your own driver. It contains compatable commands for 8563 among others.
http://www.tm.agilent.com/classes/MasterServlet?view=faq&faq-ItemID=1000003541&language=eng&locale=US
I still use the 488.2 board (successfully with WINNT, ME with patch, 95) and don't use instrument drivers, just include the NIGLOBAL.bas and the GBPI32.bas and import them into either a VB project or MS Excel. From what I've seen there are only two basic types of instrument commands, settings and queries (both text), so I don't use a pre-compiled driver. Also been successful at using Microsoft's Winsock ActiveX control for real
-time display re-creation of an Advantest SA display over the internet. Hope this might help.

Where can I find GPIB drive for Stanford SR830 lockin amplifier for labview 6?

Hi I am trying to work with the lockin amplifier (Model: Stanford Research SR830). Unfortunately, my computer only has labview 6 installed. Could you please let me know where I can download a SR830 driver of GPIB version for labview 6? I have checked the NI website. Only drivers for LabVIEW 8.0 and up are available here. http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=240C113D3165071BE0440003BA7CCD...
Please let me know. If any one could upload one, that would be so great. Thank you.

Hi Wayne,
I am assuming you obtained the drivers from ni.com/drivers webpage? You can ask someone to convert it for you on the version conversion board and you should be good to go. If you create a new thread there please post the link to it over here so we can continue assisting you. Thank you and good luck!
Regards,
Basil
Applications Engineering
National Instruments

2.2 GPIB driver for Solaris doesn't work with Sol. 2.3 tester

Upgraded to 2.2 GPIB driver to fix issue of driver being lost on Sun Ultra60's at shutdown and reboot. The driver works fine with 10 of the 11 tester platforms we use. This tester is a Genesis III running Solaris 2.3. The program will run successfully, but when shutdown and re-started, the drivers are not there and must be re-installed. What to do? Thanks.

Thanks for the suggestion to check privileges, but that's the problem--the driver is not present to have any privileges to check. On reboot, there are only links (all owned by root with 777 perm.) at /dev which lead to non-existent directories.
#/dev> ls -l gpib*
lrwxrwxrwx 1 root other 43 Apr 18 09:50 gpib -> ../devices/pci@1f,4000/NATI,pci-gpib@2:gpib
lrwxrwxrwx 1 root other 44 Apr 18 09:50 gpib0 -> ../devices/pci@1f,4000/NATI,pci-gpib@2:gpib0
lrwxrwxrwx 1 root other 44 Apr 18 09:50 gpib1 -> ../devices/pci@1f,4000/NATI,pci-gpib@4:gpib1
If you try to use these links to go to these dirs, there're not there. Also, ibconf shows no gpib devices loaded.
Any more suggestions would be greatly appreciated.

Need GPIB driver for SD380 Spectral Dynamics FFT analyzer

>Hello,
>
>I'm looking for instrument driver (or design info) eg IEEE488 or GPIB for a
>SD380 Spectral Dynamics FFT analyzer I own - this will be used on a school
>project, so I hope to find source at no cost or someone who has worked with
>such an analyzer and who can give me ideas about how to go about writing
one
>for Linux or Windows.
>
>The SD380Z I have is a single-channel unit.
>
>Please copy me at:
>
>rXoYnZaXnAMPERSANDsXuYrZeXwYeZsXt.net
>
>( remove upper-case XYZs above, and replace AMPERSAND with the character)
>
>Thank you,
>Ron

Hey Ron,
I am sorry that National Instruments doesn't have an instrument driver for the SD380. What I would recommend is finding a copy of the user manual for this device and then try to create your own instrument driver for this device. If you are using one of NI's GPIB controllers and LabVIEW it is really easy. You will need to create VIs (functions) for specific tasks and these functions will be made up of commands or strings that are sent across the GPIB bus.
Here is a tutorial on instrument drivers that is very helpful.
http://zone.ni.com/devzone/conceptd.nsf/webmain/119b3b705b84b041862567d90074f425?OpenDocument
http://zone.ni.com/devzone/devzoneweb.nsf/Opendoc?openagent&64325190560C97CE86256E4A006F27F1
I hope this helps out.
JoshuaP
Nati
onal Instruments

Has anybody got Labview GPIB driver for a Time Electronics 5021 Calibrator

Windows NT and 2000 platforms.
Time electronics ltd multifunction claibrator model no 5021 or model no 9821

Hi,
National Instruments' Instrument driver library is at:
www.ni.com/idnet.
I did a search and couldn't find an instrument driver for this instrument.
You can contact the instrument manufacturer to see if they have a LabVIEW instrument driver.
Other options are contacting an alliance member to develop the instrument driver or you can do the development yourself. Here's a tutorial on writing instrument drivers in LabVIEW:
http://zone.ni.com/devzone/conceptd.nsf/2d17d611efb58b22862567a9006ffe76/117f9eaedfd2c9e58625680a005acd06?OpenDocument
Hope this helps.
DiegoF.

GPIB Driver for SR844

Hi, I am new with Labview and want to use my new Lock in Amplifier SR844. But couldnt find any driver for it. I am using Labview 2010. Could anybody help please? It will be highly appreciated.

see here: http://forums.ni.com/t5/LabVIEW/Can-driver-for-SR830-and-SR844-be-used-interchangeably/td-p/1600796

I have Agilent 8166A(Lightwave Multichannel Sys. I did not find GPIB drive for this Equipment.I also search this driver in the web but I still did not find them. Please help me and tell me how to download those drivers

Thank you very much !!!
Michael

The Agilent 8163, 8164 and 8166 uses the same driver and they come with the mainframe. If you didn't get the driver with the mainframe, call Agilent's T&M support and ask them to email it to you.
FYI, there is a bug in the LabVIEW driver that Agilent supplied.
I hope that helps. Regards,
Shan Pin Koh
Systems Engineer
Oakriver Technology

Driver for hp 54845A?

i'm searching for a gpib-driver for the oscilloscope hp 54845A. i'm using labview 5.0.1 and 6.i. can somebody help me.

You can download it from here.

Driver for hp 54730D?

i'm searching for a gpib-driver for the oscilloscope hp 54720D. i'm using labview 5.0.1 and 6.i. can somebody help me.

Ni doesn't have one for the 54720 but I gave you the location for the 54730. You might see what (if any) differences are between the gpib commands. My guess is that the command sets are the same. You could also check Agilent's web site.

Looking for Labview driver for Agilent 4294A (HP)

Help!
I've been browsing the driver database looking for the Labview GPIB driver
for Agilent(formerly HP) 4294A Gain-Phase Analyzer.
Does anyone know where I can get it?

Hello all,
NI is interested in developing LabVIEW and CVI drivers for the Agilent 4294A. I have been trying to obtain one of these units on loan from Agilent for the past couple of years with no success. If anyone can spare their 4294A for the duration of driver development or can influence Agilent to loan a 4294A, NI will write certified CVI and LabVIEW drivers for it.
Jason Hobbs
Instrument Drivers

GPIB driver for NEC omniace RA1100

Similar Messages

Maybe you are looking for